No problems at all with my upgraded Wild UL-19 and highly recommend getting rid of the factory mount and tray.Very heavy and too much room wasted with plastic.She is gonna haul the mail with that setup👍
You should look into a rear motor mount from OSE. Rear support ring for the motor. Add strength to mounting of the motor. Also sounds a great ul19. Removing everything and doing a full inlay will light in the boat up and really wakes it up. Tip to gauge. Slide under the hull at desired height step Next to the strut. Adjust strut to new height. Also pads 21mm. Then take away 3 mm for the centerline of the propeller of strut. 18mm be the new set point.
When I do the inlay I'm gonna install a rail style mount with forward &rear support. So I used the strut gauge wrong? Lol. I've never used one before, I just looked at your website I see exactly how to use it now. Thanks for the support brother,
@@IRONCLADRC I was afraid you were gonna say that lol. Firma 160a 😳. I kinda like the smart info on remote. Especially the ECS temp. Think it’s even worth trying? I got the motor installed. Was gonna test it tomorrow.
@@IRONCLADRC you're the man! Thanks! Been kinda down on my UL 19 been through a hull and a whole pile of electronics trying to get back to 63 where it was at before stuck at 60 now 🤷🏻♂️ but this is giving me motivation to keep pushing to get it back to right
Now, finally, you'll enjoy this hydro on 6s without temp issues. Bigger motor and ESC is the way to go for that. Use 70C or higher lipos. Watch out for blow overs now. Upgrading the flex wire is a must now. Good choices. Enjoy. Remember to lube the flex.
Hopefully the wind corporates this evening so I can go to the speed run spot? If not I may have to do my testing at the park pond? 12mph wnw wind today tomorrow's forecast looks good 2mph SW
NICE!!! Great clean build, watching this I my have figured out my motor cooling problem👍 Can’t wait to see it run! and the read outs from your new transmitter, can you change the voice to a sexy French girl 😂🤣😂
![ARGENTINA vs. PERÚ [1-0] | RESUMEN | ELIMINATORIAS SUDAMERICANAS | FECHA 12](http://i.ytimg.com/vi/xtI25ENDDSY/mqdefault.jpg)
I always learn so much from watching your videos!! Thanks for all the time you take to make these videos!!
Glad you like them! Thanks for watching
Amazing detail.. this is how it should be done!!!! Attention to detail!!! Something that's missing these days. New sub
No problems at all with my upgraded Wild UL-19 and highly recommend getting rid of the factory mount and tray.Very heavy and too much room wasted with plastic.She is gonna haul the mail with that setup👍
What did you use for a mount, I've been looking at the tray from OSE
www.offshoreelectrics.com/proddetail.php?prod=ose-83394
Same link below,OSE carbon fiber mount 40 mm👍
Fun build Big B! You will love the rail system on this boat, gives you a lot more room for your batts and a lower more centered cg.
So, what are waiting for? Grab your jacket and a cup’a joe and head for the pond!
You should look into a rear motor mount from OSE. Rear support ring for the motor. Add strength to mounting of the motor.
Also sounds a great ul19.
Removing everything and doing a full inlay will light in the boat up and really wakes it up.
Tip to gauge.
Slide under the hull at desired height step
Next to the strut. Adjust strut to new height.
Also pads 21mm. Then take away 3 mm for the centerline of the propeller of strut.
18mm be the new set point.
When I do the inlay I'm gonna install a rail style mount with forward &rear support.
So I used the strut gauge wrong? Lol. I've never used one before, I just looked at your website I see exactly how to use it now.
Thanks for the support brother,
@@IRONCLADRC you did was good with the gauge. May uses for measuring so I think it was a good demonstration and use.
Think I’ve watched this video 10 times lol. Couple hot totties & installing the oxidean 2200KV in UL19 for me tonight!
Good luck with the build, what speed control are you running? Really need a minimum of 200a for the 2200kv oxidean
@@IRONCLADRC I was afraid you were gonna say that lol. Firma 160a 😳. I kinda like the smart info on remote. Especially the ECS temp. Think it’s even worth trying? I got the motor installed. Was gonna test it tomorrow.
Can’t wait to see her run!! I’m always learning new setup tricks from you. Thanks!
Me too. Going to the park pond for her initial run then the speed run spot following day very windy today. Grrr
Looking forward to seeing it Rip, lotsa power @ the finger tip!
Awesome 🤟 can't wait for more on this boat!! Please do a full video when you do the inlay🤞🤞🤞
I will definitely make a video on the ul19 reinforcement Inlay process
@@IRONCLADRC you're the man! Thanks! Been kinda down on my UL 19 been through a hull and a whole pile of electronics trying to get back to 63 where it was at before stuck at 60 now 🤷🏻♂️ but this is giving me motivation to keep pushing to get it back to right
Waiting for the launch!! Great explanation of the buid
Now, finally, you'll enjoy this hydro on 6s without temp issues. Bigger motor and ESC is the way to go for that. Use 70C or higher lipos. Watch out for blow overs now. Upgrading the flex wire is a must now. Good choices. Enjoy. Remember to lube the flex.
Thanks brother I did the maiden in today's upload. She's an absolute beast
Put you coat on Bro and get to the park pond ...Awesome build..
I did video will be out in the morning
@@IRONCLADRC lmao ..awesome can't wait to watch it Brother...
Great job Big B looks good. Dying to see this beast run.
Hopefully the wind corporates this evening so I can go to the speed run spot? If not I may have to do my testing at the park pond? 12mph wnw wind today tomorrow's forecast looks good 2mph SW
I can't wait to see it run!
NICE!!! Great clean build, watching this I my have figured out my motor cooling problem👍
Can’t wait to see it run! and the read outs from your new transmitter, can you change the voice to a sexy French girl 😂🤣😂
Great info! Im going to get the Zipp flex cable since Im running 6s. How do I get the teflon tube out?
Going for the fastest ul19 on RUclips I see
Was gifted a free Max 6 ESC is there any way to change it to water cooled
Question, why you changed ESC to Oxidean from ZTW? If it is ok to ask. Thanks
I had an ose 150 in this boat I've always had the ose/flycolor 15p in the ul19
What u do for cooling?
Where can I find the mad lizard strut gauge?
www.madlizardproducts.com/product-page/hydro-strut-gauge
@@IRONCLADRC thanks much appreciated
When??????
IT WILL BE A SCREAMER☠
Thats going to haul ass...!!!