The BIGGEST Mistakes DIYers Don't Know They Are Making When Wiring Receptacles | How To

Поделиться
HTML-код
  • Опубликовано: 26 авг 2022
  • In this video I show you some of the most common mistakes that are made when installing receptacles. Some of these are not done by just DIYers, I have seen professionals make some of the same mistakes. Hopefully this will help with some things I have found to look out for or at the very least, a good reminder!
    Products In the Video:
    Klein 11 in 1 Magnetic Screwdriver (combo bit not included): amzn.to/39RoKIN
    Klein Combination Bits: amzn.to/3yjxvEV
    MILWAUKEE 13-in-1 Screwdriver With ECX Bits: amzn.to/3ndPEOb
    Klein Non Contact Voltage Detector: amzn.to/3wCmSws
    Klein Outlet Tester: amzn.to/3OHcrgt
    Don't see what you are looking for? Here is my How To Home Amazon Store, where you can find many of the tools and shirts I use and wear in my videos! amzn.to/3mcqu1E
    Thank you for watching and for subscribing. You can support the channel at no cost to you by using one of the above affiliate links. This helps support the channel for new content!
    Blessings,
    Adam
    How To Home assumes no liability for damage or injury. How To Home highly recommends using proper safety procedures and professionals when needed. Our content is for entertainment purposes only. No information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not How To Home. How To Home will not be held liable for any negligent or accidental damage or injury resulting from equipment, tools, electrical, fire, electronics or any items contained in this video. Attempt projects and repairs at your own risk.
  • ХоббиХобби

Комментарии • 7 тыс.

  • @HowToHomeDIY
    @HowToHomeDIY  Год назад +530

    So these are some of the most common mistakes I have observed and even been guilty of in the past. Which ones did you find helpful and are there any that you think could be added to this list? Thanks!

    • @andywrites2141
      @andywrites2141 Год назад +16

      I always check to put the hot on the same side as the smaller opening on front of receptacle. Modern receptacles have a larger opening on the neutral side and smaller on hot side.

    • @lawrence7dyer865
      @lawrence7dyer865 Год назад +14

      Yes you cannot use the device as a splice or land the incoming wire on one screw and the outgoing wire on the other screw. The only reason there are 2 screws on each side is if you are making the top and bottom being fed with 2 different circuits at which time you break the jumper between the screws to separate them.

    • @lawrence7dyer865
      @lawrence7dyer865 Год назад +11

      Also the code says when you land a wire under a screw the wire must be at least 75% around the screw.

    • @DeltaCo7175
      @DeltaCo7175 Год назад +2

      @@lawrence7dyer865 or if your making half switched receptacle

    • @bobbytheboss
      @bobbytheboss Год назад +1

      Thank you from a plumber in North Carolina

  • @padler5106
    @padler5106 Месяц назад +30

    I'm a retired electrician (40 years) and I found this video excellent. Well done and well worth it for anyone including electricians to watch

  • @lj5833
    @lj5833 18 дней назад +25

    Do you realize how rare it is to post a diy video and not get a bunch of "experts" to rip you a new one? Well, this guy pulled it off. Gives valuable info. Oh, and I too am glad you don't have obnoxious nor any music in the background. Not needed. The info is the star of the show.

    • @HowToHomeDIY
      @HowToHomeDIY  13 дней назад +2

      Really glad to hear you liked it so much. Thanks a lot for the feedback! It is very much appreciated!

    • @OldiesandOldschool
      @OldiesandOldschool День назад

      Im pretty sure he was itching to play music on the background but probably didn't because of the copyrighted songs! Can't monetize your video with copyrighted music

    • @HowToHomeDIY
      @HowToHomeDIY  День назад

      @OldiesandOldschool I pay a licensing fee monthly to use a bunch of copyright free music. However, I haven’t used any songs in a year or 2 in my videos because they can be distracting. So no itch 😎

    • @OldiesandOldschool
      @OldiesandOldschool День назад

      @@HowToHomeDIY thats valid!I was wrong....uh - gen!

  • @stanleyo7140
    @stanleyo7140 Месяц назад +23

    Very good information. As an electrician for over 35 years and electricla instructor for over 20 years, this video is very accurate and provides good information. The only caveat I would add is usung the word "short" in my experience there were more "opens" than shorts, meaning a bad connection will open the circuit, not allowing for the flow of current. Great video!

    • @Mike-01234
      @Mike-01234 8 дней назад

      Just wondering why do manufactures continue to make outlets with backstabbing holes if it's so bad? Have you personally seen those things cause problems. The outlets are UL certified think if it was that bad they would not be certified. Short circuit is what you want so it trips the breaker open is worse someone could get shocked if a metal J-box, or conduit is not grounded.

    • @stanleyo7140
      @stanleyo7140 8 дней назад +1

      @@Mike-01234 The only reason I can possibly understand that the backstab is still allowed is that it is an Approved and Listed application. I have seen many Approved and Listed items not work optimally, however, the Authority having jurisdiction, may decide to not allow the backstab method in their jurisdiction, as it is an improvement and not a lowering of the Approving and Listing authority. I never allowed it nor did any of my employers when I was working in the field. I have seen too many instances where the wire would, due to heating and cooling of the conductor, cause the spring tension of the quick connect to lose integrity and allow the conductor to have intermittent contact with the termination on the backstab. In my experience, the neutral wire was the culprit. I hope this helps explain the reason.

    • @Mike-01234
      @Mike-01234 7 дней назад

      @@stanleyo7140 What do you think of those receptacles have the lever connection like a Wago.

    • @stanleyo7140
      @stanleyo7140 6 дней назад

      @@Mike-01234 If you mean the type that use a clamp mechanism internal to the device, I have found those to provide an adequate mechanical connection, they seem to work better if two wires are inserted side by side so that the clamping mechanism is not at an angle with just one wire. Thanks for the question.

  • @marketingmikesmith
    @marketingmikesmith 6 месяцев назад +18

    I always praise people like this for taking the time to show us these educational videos...I've learned so much and saved so much money over the years, that I can't give this guy enough compliments. Thank you!

  • @le8026
    @le8026 10 месяцев назад +95

    Great demonstration. No junk music, no bleating or blathering; straight to the point and focused. Thank you.

  • @maristobbe3378
    @maristobbe3378 Год назад +311

    I really appreciate the efficient use of time - every minute was necessary, no unnecessary chatting, straight to business. If I miss something, I can back up. Valuable information for a DIYer. One shouldn't have to call an electrician for something this small and you wrap up the important safety issues.

    • @jayare5931
      @jayare5931 Год назад +13

      BRAVO on efficient use Of time !
      I am so busy I sometimes think I’m going nuts,
      but your information is spot on in time management and stress-relief
      for me, and that is something you don’t
      see too often here.
      Thank you

    • @JustinAddis-wj7dz
      @JustinAddis-wj7dz 12 дней назад

      Justin will get ⚃ in a 🕖 and a couple times in a row and 🕖 is not in

  • @KyleHarrisonRedacted
    @KyleHarrisonRedacted 6 месяцев назад +4

    Just that little tip near the start about the gauge on the back of the outlet… immediate thumbs up. No one yet has mentioned that, and I surely would have missed it

  • @emmgeevideo
    @emmgeevideo 2 месяца назад +4

    I've been doing DIY electrical for years. The house hasn't burned down thank goodness. No injuries. But I know I've committed every sin on your list and in one of your companion videos. I found your videos today before embarking on adding a new wall plug because I thought I should get some tips. I followed several of yours, particularly the ones regarding how to correctly twist wires and use wire nuts. I feel so much better knowing I did it right. Worked first time too 😊 Thank you for your clear instructions!

  • @Angel-tm7du
    @Angel-tm7du Год назад +48

    I have always been a DIYer but have no formal training. These videos you have taken the time to make are awesome for me.. I would like to change out my receptacles (they are 51 yrs old). Now I have a good idea what to buy and the proper install. AND... Thank all you commenters. I have learned from you also with your great questions and comments. The cameraman rocks!!!! Thank you again👍👍

    • @kurtvanluven9351
      @kurtvanluven9351 11 месяцев назад +3

      Hope you have copper/instead of Aluminum/ wire in your house. Let me tell you how (not) fun it is to change outlets in that situation!

    • @johnbagewll2321
      @johnbagewll2321 10 месяцев назад +1

      @@kurtvanluven9351
      You can use CO/ALR, CU-AL, or AL-CU stamped and approved devices instead of pig tailing everything right? If you have aluminum wiring.

    • @Angel-tm7du
      @Angel-tm7du 10 месяцев назад

      @@kurtvanluven9351 guess I will have to investigate this further. Things May be different here in so. Florida. Thank you for your reply. 👍

    • @Angel-tm7du
      @Angel-tm7du 10 месяцев назад +1

      @@johnbagewll2321 thank you for your reply and comment. Will investigate further. Things May be different here in So. Florida. 👍

  • @CherokeeSprings3320
    @CherokeeSprings3320 4 месяца назад +11

    Great job, Adam. Keep 'em coming. I know nothing about any of it but I find myself at a place in life where everything seems to need repair and there's no one to do it but me and little resources. You're helping tremendously. Thanks so much.

  • @toryshew6228
    @toryshew6228 8 месяцев назад +8

    I am by no means a licensed electrician but I have most definitely done a lot of my own wiring and electrical work in the past. And I got to say there's a couple things in here that I had no clue about so I appreciate that! Thank you very much

  • @kassidysell7454
    @kassidysell7454 8 месяцев назад +23

    That measurement tool on the receptacle is 🤯 I audibly gasped, haha. So glad you mentioned it! My shop teacher in high school taught me to use my pinky from the top of the nail to the first knuckle but this is much more useful. Your videos are always so well explained without any useless chatter. Thank you for your time and effort!

  • @jimchurchman2628
    @jimchurchman2628 Год назад +15

    You need to demonstrate what a “pigtail” is for multiple wires hooking to a receptacle! Good video!

  • @bryancasey1046
    @bryancasey1046 2 месяца назад +4

    I love this! I was preparing to replace two duplex receptacles in my bedroom, after they had failed following a substandard installation by a 'jack of all trades' type. My suspicions were correct as to the cause of the failures, and now I am confident I can safely and effectively replace both with the desired results.
    Thank you!

  • @LocomotiveServiceInc
    @LocomotiveServiceInc 5 месяцев назад +12

    Adam, I'm truly grateful. Your videos have not only made my home electrical projects more enjoyable and safe but have also given me a deeper understanding of the processes involved. Thank you!

    • @HowToHomeDIY
      @HowToHomeDIY  5 месяцев назад +1

      You are very welcome. Really glad to hear you are finding value in the channel. Thanks a lot for the feedback!

    • @Jbmc65
      @Jbmc65 3 месяца назад

      @@HowToHomeDIY Adam, Do you have a video that shows how you wire receptacles in a series, Like home run comes to first one then you have another wire to next and so on? Thank-you in advance for all you do.

  • @hortonhcci
    @hortonhcci 11 месяцев назад +45

    Really excellent video. Adam is a great teacher--he shows you a common error, invites you to speculate what might be the problem, and shows/explains the potential consequences of poor practices. Only then does he demonstrate proper technique. This is what good teachers do, and it's why I'll remember these lessons years from now when I take on these kinds of tasks.

    • @jmor2252
      @jmor2252 18 дней назад

      This is what I was coming to say. Fantastic instruction, close up, slow enough to take everything in but not so slow that you mentally wander off. Perfect instruction style.

  • @oisiaa
    @oisiaa Год назад +51

    I went on Amazon and bought those Klein combination bits immediately. In my whole life I don't think I've ever gone from not knowing something exists to buying it so quickly. I've done a lot of electrical work and that bit looks amazing!

    • @oisiaa
      @oisiaa Год назад +2

      @@mft760 I just used these bits today. Worth every cent!

    • @Springerpop
      @Springerpop Год назад +1

      Just like you, I went from not knowing about the bit to wanting one immediately.
      Imagine my frustration when Amazon told me they were sold out. Home Depot says the same. Guess I'll just have to wait until they're back in stock somewhere.

    • @mjmsongs
      @mjmsongs Год назад +1

      Heading to Amazon right now!

    • @waynebinky
      @waynebinky Год назад +4

      A Robertson works great too but most Americans don't know it exists. It was developed by a Canadian in the early 1900's.

    • @garyhoney2013
      @garyhoney2013 Год назад

      FYI they Irwin makes an extendable nut/screwdriver goes out to approximately 11 plus the base that love too in addition to the one you mentioned.

  • @user-hp4qd4qt6k
    @user-hp4qd4qt6k 2 месяца назад +3

    You do a great job of explaining wiring mistakes and showing it in a way that makes it easy to understand! Great stuff!

  • @jeffreyhunt8204
    @jeffreyhunt8204 Месяц назад +3

    I enjoy your easy to follow instructions, your knowledge and the direct approach you use in your videos. I also love your organized tools. Makes my OCD very happy.

    • @HowToHomeDIY
      @HowToHomeDIY  Месяц назад

      Really glad to hear you are finding value in the channel. I too have touch of OCD haha Thanks a lot for the feedback!

  • @user-iz5ke5so9d
    @user-iz5ke5so9d 11 месяцев назад +62

    Very helpful videos. I would suggest one step prior to wiring or replacing receptacles. That step is to use a polarity tested on the circuit before making any changes. Years ago, I had to replace a receptacle with a damaged plastic face. I removed the receptacle and rewired it according to code, as you have shown. When I was done, I checked the polarity and was surprised when it showed reversed. I double checked the wiring on my new outlet and the black and white wires were correct. I then used a voltmeter to check the wiring and found that the WHITE wire was hot and the black was neutral. Long story short- I traced the problem to the electrical panel. The white wire was wrapped with a piece of black tape and connected to the hot side of the breaker; the black wire wrapped with a white tape.
    I talked to the City Building Inspector who told me that if the black wire is compromised during construction, it was permissible to reverse the wires for that circuit as long as all of the connections in the house also were marked with white/black tape. I went through the house and checked all outlets on that circuit for tape and only about half were actually marked. Assuming that the existing wiring is correct was my first mistake!!

    • @tommybotts
      @tommybotts 8 месяцев назад +4

      So much for the validity of Building Inspectors.

    • @chrisowen2925
      @chrisowen2925 8 месяцев назад +2

      @@tommybotts Where it would have taken little time and been easier to switch the white and black instead of going to every outlet and marking it with black and white tape... Some people just take the lazy way out. And electricians have to be licensed. So let us assume the house never had a DIYer doing the work prior to this. That becomes scary as to how many homes that particular electrician did. Once the wall is closed, they can get away with anything and you never know what is behind the plate unless you do the inspection yourself.

    • @rubiconklbrutorowman7577
      @rubiconklbrutorowman7577 7 месяцев назад +2

      Wow that is eye opening reminder! I will definitely buy polarity tester. It is like we must not take face value of anything and everything indeed! Glad read comments down this far and kudos 2 U sharing with us spine chilling Infor that any house can be burn down with things like totally irresponsible house builder and wiring person(s) failed stated or post on circuit breaker panel! Dam on them!

    • @rubiconklbrutorowman7577
      @rubiconklbrutorowman7577 7 месяцев назад +1

      Ys spine chilling or house can be burn down! So many despicable ahols out there, among other ahols!@@chrisowen2925

    • @EMPYS
      @EMPYS 6 месяцев назад

      My house was a convent and built in 1925. The prior owner had replaced the knob and tube and did new wiring, but as I've been changing old 2 prong outlets for 3 prong, and I've noticed the white wire is hot and connected to the brass side. Now I'm concerned that it might be more than just connecting to the right side of the outlet, and I should really get an electrician in here to make sure there's not a fire waiting to happen. I've heard bussing on the walls, and the bathroom light (which still has the push bottom switch) comes on when it wants to a well as the lights and ceiling fan in my living room, and the AC trips because there seems to be too much on one circuit. 😢 I've been trying to save money doing a few things myself, but it might be time for a pro to make sure my family is safe.😮

  • @HeyChickens
    @HeyChickens Год назад +21

    The combo bits in the video were cool! I figured such a tool must exist, but you just confirmed it! Excellent hands-on demonstration of the wrong and right ways to wire up outlets!

    • @HowToHomeDIY
      @HowToHomeDIY  Год назад +1

      Yeah they are really helpful! Really glad to hear you liked it. Thanks a lot for the feedback Bryan!

    • @meaninglessname123
      @meaninglessname123 11 месяцев назад

      The screwheads on the outlets were specifically designed to be tightened with either a Philips or a slotted screwdriver, for convenience. They were not designed to require a special bit. For the DIYer, it is my opinion that a special bit may be nicer to use, but it is not necessary. A Philips bit in GOOD CONDITION is, however, necessary. I also think the combination screwheads are a stupid idea and that simply using a standard Philips screwhead would have given the best results since the combo screwhead is not a *perfect* fit for either Philips or slotted.

    • @toriless
      @toriless 10 месяцев назад +1

      I have an insulated set. They have red rubber on them.

  • @sandycross4827
    @sandycross4827 2 месяца назад +2

    I would never consider doing my own electrical work, but your videos are incredibly helpful for demonstrating when things haven’t been f do one correctly and what the consequences could be. Many thanks for taking the time to share your expertise and for explaining things so well.

  • @joshuagibilisco9522
    @joshuagibilisco9522 5 месяцев назад +2

    I didn't think I was going to learn anything, just looking for refreshers. But I need to go out and get some of those bits. Thank you for sharing.

  • @lynnskinner4457
    @lynnskinner4457 Год назад +19

    I've never done any electrical work. It always sounded simple but scared the crap out of me. And now I can see I was smart not to touch it. It's more complicated than I thought it was. So Props to all the people who know what they're doing. You're appreciated.

    • @keithmarlowe5569
      @keithmarlowe5569 Год назад +2

      Everything is more complicated than you think it is. There is a reason for permitting, inspections, and requiring licenses.

    • @coffeebeforemascara
      @coffeebeforemascara Год назад +2

      Same! But isn't it so crazy clever that they molded a stripping gauge right into the back of the receptacle so you know exactly how much insulation to strip from your wire? Absolutely freaking brilliant!

    • @toriless
      @toriless 10 месяцев назад

      @@coffeebeforemascara Modern "smart" device do not have it ...

  • @hami8664
    @hami8664 Год назад +9

    I’ve seen a lot of these mistakes around my house changing the receptacles. As for myself doing the replacements, this video of the explanation of doing it right and safely replacing them, had helped me a lot better.

  • @davidworker4053
    @davidworker4053 4 месяца назад +2

    Great tips! It's amazing learning these little details to really make the process much safer and easier (strip gauge on back of outlet, different screw tips, clockwise wire curling, etc.). I thought before the video that there wasn't much else to learn about installing outlets but I was proven wrong. Thank you.

  • @tomhyde1138
    @tomhyde1138 7 месяцев назад +4

    Great video! Hugely helpful for a newb such as myself that wants to do some basic stuff around the house. Informative and very easy to follow and understand. Thank you!

  • @gwmattos
    @gwmattos Год назад +8

    I just purchased a receptacle looking very much like yours and I learned a couple of new things and I thank you for bringing this to all of our attention out here who are do it yourself installers in our own homes and that I really appreciate.

  • @BWGPEI
    @BWGPEI Год назад +44

    As an old technical writer, I am impressed by how well you demonstrate your points. Very nicely done!

  • @rodweichlein3104
    @rodweichlein3104 Месяц назад +1

    So great to listen and learn from an individual that delivers an easily understood tutorial !

  • @user-tx2yt2nh8k
    @user-tx2yt2nh8k 11 дней назад

    Excellent instructor. I am 40 years of electronic and electrical technician and am totally agreed this video is present the best experiences. I would give you 2 thumbs up

  • @Richard-bg1rz
    @Richard-bg1rz 11 месяцев назад +43

    Just stumbled upon your channel. Excellent job on this video! As a Master Electrician for about twenty years I can’t think of anything you missed on this specific topic. Only thing I would have added would be the rationale: poor mechanical connection = arc = heat = fire.
    I especially despise the backstabbing technique (wish they would stop making it). I live near the coast, the humidity here exacerbates the corrosion of the tab that makes contact with the wire in a backstabbed receptacle. I can’t even guess how many I’ve replaced with a beautiful little smoke trail on the wall above them!
    Again, great job! Looking forward to checking out the rest of your content.

    • @cbohmable
      @cbohmable 6 месяцев назад

      WHAT ABOUT USING DEVICE AS A SPLICING MEANS ( ONLY ONE GROUNDED WIRE ON DEVICE)

  • @Jeff-vh1zz
    @Jeff-vh1zz 9 месяцев назад +19

    Hey brother. Thanks for the video. One other common receptacle mistake I have encountered while helping others out is the 'split receptacle' found in most Canadian kitchens. I had a neighbour come over in a panic asking me to help with a wiring issue. It seems that her husband had switched all of the old style receptacles in the kitchen to Decora models and failed to break the tab between the upper and lower receptacle openings so her toaster was now getting 240v. It was hysterical because the ceiling was glowing red when you pressed the toaster lever. I am sure that some of your viewers are not familiar with split receptacles. (I have not had the opportunity to see if this is addressed in another vid.) Lastly, a common issue that I encounter is that electricians have installed the receptacles using one screw and then leave the other screw extended instead of turning it in so that there is less chance of contact with the ground wire or the box. Best practice would be to tighten all screws.

    • @stevieg.4816
      @stevieg.4816 Месяц назад

      Using a split receptacle clearly marking the wires in the box, on the plate, and in the panel. Still not a good idea as a person not an electrician they can be severely harmed, dead or potentially cause a fire. That box split now has the potential of 240v. My advise, add the extra box and separate the circuits that way. Oh, and yes I have been an Electrician for over 45 years, residential, commercial, and industrial. We don't leave things, ( it could happen) we leave things so it can't happen.

  • @darrellpizzagoni5182
    @darrellpizzagoni5182 Месяц назад +2

    I watched this very informative video today.
    I am not a professional electrician and really don't like playing with electricity.
    You taught me some very important points about installing receptacles that I never knew.
    Thank you for what you are doing for us layman.

  • @glenngilliard4112
    @glenngilliard4112 3 дня назад

    Very good! You of course are spot on on everything you said! It is suprising how many people don't know what you show in this video.

  • @stephenlong5297
    @stephenlong5297 Год назад +6

    Just want to say thank you for taking the time to make this video. I'm hardcore about learning everything I can to be self-sufficient. I I can seldom afford to pay a professional. On behalf of everyone else in a similar situation I would like to express my gratitude and convey my most sincere thank you for showing us how to be safe with this stuff

  • @michaelbecchio8738
    @michaelbecchio8738 9 месяцев назад +14

    Man this video was SO helpful! Didn’t even realize the things I’d been doing wrong. Thanks so much my man! Thorough but succinct, and very informative. Props 🙌🏼

  • @andyvoltin9321
    @andyvoltin9321 26 дней назад +1

    Thank you, your explanation of the failures makes it a lot easier to understand/remember. Thank you

    • @HowToHomeDIY
      @HowToHomeDIY  13 дней назад

      You are very welcome! Really glad to hear you liked it. Thanks a lot for the feedback Andy!

  • @user-sv5xo6kw7b
    @user-sv5xo6kw7b 28 дней назад +1

    Thank you for the clear instructions and rookie mistakes. You have saved me from some serious future problems as I switch out an old painted wall outlet.

    • @HowToHomeDIY
      @HowToHomeDIY  13 дней назад

      You are very welcome! Really glad to hear you liked it. Thanks a lot for the feedback!

  • @travisbond1974
    @travisbond1974 9 месяцев назад +21

    Amazing. Been doing home projects for a few decades and I’ve learned a massive amounts of better techniques huge help. Thank you so much. Also, this is one of the most professional videos I’ve seen in terms of actual close-ups in focus, and the voiceover demonstrating precisely what you’re doing.

  • @fleedopmogu6169
    @fleedopmogu6169 Год назад +9

    Explained nicely in a efficient concise manner. Good video shooting as well as verbal explanations. I pretty much knew all this info but your presentation, concise treatment of info, and the efficient videography is all very impressive. Thanks. I REALLY especially liked the simple but extremely illustrative example of the clockwise tightening on the clockwise bend. Just fixed a DIYers circuit where the dude tightened all the connections and you could tell it was random the way the DIYer placed all the bends or hooks. The guy was a self professed "expert" but had no clue that a counterclockwise bend would spread out or widen upon tightening. ...... and I'm a DIYer, but someone taught me early on that the direction of bend matters.

  • @milushapetrica3018
    @milushapetrica3018 15 дней назад

    I have to replace an outlet in my kitchen. Never done it before. This video is hugely helpful specifically the strands of wire/stiff single wire demonstration as well as the direction of the hook. Now I hopefully know what to expect /correct when I attempt it this week. Wish me luck!

  • @wandajames6234
    @wandajames6234 7 месяцев назад +1

    Awesome! About time someone covered basic common errors and showed the right way. Thanks!

  • @drayerink
    @drayerink Год назад +14

    Really helpful, I have always done these things instinctively (getting the stripped length correct and the hook in the right direction). I'm unfamiliar with US receptacles, so it was helpful to have a guide to the wiring layout and attachment, too. Thank you for this clear and helpful guide!

    • @HowToHomeDIY
      @HowToHomeDIY  Год назад +3

      You are very welcome. Glad you liked it. Assuming you are in Europe somewhere?

    • @drayerink
      @drayerink Год назад

      @@HowToHomeDIY no, I am from New Zealand, recently moved to the USA and doing some home reno, so learning how they are set up is useful :)

  • @joeblow1104
    @joeblow1104 Год назад +3

    One of the best electrical videos I’ve watched. Your examples go right down to the point. I knew most of these but watching your video definitely!

  • @fewworddotrick
    @fewworddotrick 20 дней назад

    Nice tips. My dad was a 40 year journeyman lineman and wired my whole house so that provided a great example to learn from. Another one is install your outlets with the ground plug facing up. A lot of people will say that's goofy or unnecessary but just like this other stuff in the video it's just little things that over time minimize the chance of something going wrong in the future. GFIC outlets are designed to be oriented with ground plug up, I suspect so that anytime there's water in the area it will be less likely to splash on the hot terminal first, from above.

  • @gweedomurray9923
    @gweedomurray9923 8 дней назад

    I have seen different configurations of Phillips head drivers. Some will fit the screw snugly while others, being of a larger or smaller tip, or more tapered, will easily slide out. I always match up a given driver to the screws it will be turning. Concise presentation with very good video quality and best of all no cheesy "music" overlay. 🙂👍 ...The specialty drivers shown at the end are really neat.

  • @SarcasmForDummies
    @SarcasmForDummies Год назад +368

    I am not a professional electrician but have done a lot of electrical work myself due to not having the finances to pay a professional. I always research and make sure that I'm doing it the right way. Years ago I had to read the books that I still own and would make sure everything was done right. Today having the ability to see videos like this is an amazing thing. The learning process is far faster when seeing visuals. I have a quick project today and was just refreshing myself; so thanks!

    • @universalask
      @universalask Год назад +2

      @@jayhaines1792 what do you mean feed through. The one where he was complaining that two wires were attached to one screw?

    • @kamakaziozzie3038
      @kamakaziozzie3038 Год назад

      @@universalask yeah jay haines is right.
      I’m a 22 year electrical contractor and concur with him.

    • @RetiredBassist
      @RetiredBassist Год назад +2

      I like to use large wiring boxes and bring all the wires together with scotch-lock or wire nut so only one set of wires go to the receptacle. If you have to change a receptacle or switch, you don’t open circuit and have power possible on the any neutral or uncontrolled hot.

    • @RetiredBassist
      @RetiredBassist Год назад +8

      @@jayhaines1792 I look at residential wiring as the worst possible chance of problems. Even if the power is turned off, someone could be using the neutral as a return for power else where. Funny, it was my dad who pointed it out and proved it while remodeling a house. So always take care when breaking neutrals and test wires, unless the main breaker is shut down.

    • @RetiredBassist
      @RetiredBassist Год назад +3

      @@jayhaines1792 I agree your experienced and licensed. My comment was for those who trust that a turned off breaker is safe. It is never totally safe. Respect the power and treat all wiring as hot unless it is ground clustered and tested.

  • @leowiebe2101
    @leowiebe2101 Год назад +15

    Even though I'm an electrician. I'm happy there is someone like you who cares enough to explain to DIYers. The do's an don'ts. You're doing a really go job on explaining. With your illustrations.

    • @HowToHomeDIY
      @HowToHomeDIY  Год назад +1

      Glad you liked it. Thanks for the feedback!

    • @leowiebe2101
      @leowiebe2101 Год назад

      @@spinnymathingy3149 I've seen some better work by unqualified people than some Electricians to the point where I'd say. "NO"

    • @leowiebe2101
      @leowiebe2101 Год назад

      @@spinnymathingy3149 You have no idea what i have seen in my lifetime I have to defend some of these DIYers seriously.

    • @leowiebe2101
      @leowiebe2101 Год назад

      @@spinnymathingy3149 This is exactly why I had to fire a lot of my so call ticketed or red sealed skilled trades men. And started selected training my own contractors. From scratch all 60 of them until they changed the law that had to be certified. and being under my company at the time. they were fully qualified. I didn't have near the stress.

  • @michaelbauchan250
    @michaelbauchan250 4 месяца назад +1

    Excellent training and reminders for young and old DIYers. Thank you.

  • @christopherallen5603
    @christopherallen5603 3 месяца назад +3

    Great video. There's newer outlets I've installed recently with a version of the speed wiring inserts where you also tighten the screws to fasten them in that clamps with a much higher connector contact area.

  • @eltorpedo67
    @eltorpedo67 Год назад +25

    Always appreciative of the folks that take the time to make these helpful videos. Special shoutout to you for the stellar camera positioning, lighting and angle. You made sure we could see every thing you were talking about with perfect clarity. Well done!

    • @brugges
      @brugges Год назад

      No offense, but the folk takes the time to make these the videos primarily in the hope to make a living out of it 😉

    • @meaninglessname123
      @meaninglessname123 11 месяцев назад

      Why can't it be both to help DIYers and also to make some money? I have seen plenty of videos that were made only to make money and did not explain EVERYTHING in detail like this gentleman does. This video is really thorough.

  • @Capalmer01
    @Capalmer01 11 месяцев назад +4

    Well done dude . . . I'm not a licensed electrician but I do ALL these things, great tips. One thing that a buddy of mine told me not to long ago that he does as well, is once he's finished making the connection he runs a roll of electrical tape around the outside of the back square to cover all the connections and ensure that no wires touch when pushing the receptacle back in the box. Another guy I knew used to install the receptacles upside down . . . in the off chance that if a plug was loose and if something metal fell across the top connecting the two prongs. Oh . . and backstabbing is THE WORST !!! I had rental properties for years and almost every electrical issue was due to backstabbing the receptacle

    • @ruffxm
      @ruffxm 11 месяцев назад +2

      When I was an apprentice, I used to wrap tape around receptacles as well - I learned that growing up...But the mechanics made me break that habit....They'd say that's the sign of a novice. If wires are stripped and terminated properly, there's no reason you would need the tape...no copper is showing, wires are secure - what wires would touch when you pushed it into the box? If it was a real issue, NEC would address it.
      The upside down method is not wrong, but the perfect storm of scenarios would be needed to cause an issue - which is why NEC does not govern a receptacle's orientation. I actually performed an experiment with students when teaching a night course at a trade school. They couldn't get something to cross blades without helping the situation along.

  • @ssarraf6855
    @ssarraf6855 4 месяца назад +1

    Very good tips. To the point. No hash, music, or other distractions.
    Keep up the good videos.
    Thank you 🙏🏼

  • @krazjl
    @krazjl 5 месяцев назад +1

    Wow! Finally, someone who can make an extremely efficient & to the point video. Nice job ! Best I've seen in a while.

  • @keeblerkelloggs
    @keeblerkelloggs Год назад +11

    I was aware of the mistakes you pointed out, there's one more that could go on your list that I'm aware of, if only one wire is going on the hot and neutral terminals, always be sure to tighten the screws that are not being used so the heads are not sticking out where a person could accidentally touch them or contact a ground wire when pushed into the box .
    Was not aware of the different screwdrivers for tightening the screws, will pick one up.
    Thanks!

  • @chuckgrilliot3705
    @chuckgrilliot3705 5 месяцев назад +1

    Thanks for the video. Popped up in my feed just as I was getting ready to replace a bunch of outlets around the house. Excellent timing!

  • @thenathanielhardyproject8675
    @thenathanielhardyproject8675 2 дня назад

    Why can’t other videos be more informative ℹ️ like yours without the music and just getting straight to the point? Great video! Being once an electrician myself this is GRRRRRREAT information passed on!

  • @jasonnorthcutt3771
    @jasonnorthcutt3771 Год назад +3

    Haven't done any wiring in a decade or so but you're advice is solid.

    • @HowToHomeDIY
      @HowToHomeDIY  Год назад

      Really glad to hear you liked it. Thanks a lot for the feedback!

  • @chughes737
    @chughes737 Год назад +10

    Great video, learned a couple things, I don't see many DIY channels explain things as clearly or with the details you include. Well done!

    • @culbyj3665
      @culbyj3665 Год назад +1

      dude dont listen to these type of vids

    • @HowToHomeDIY
      @HowToHomeDIY  Год назад

      Really glad to hear you found it helpful! Thanks a lot for the feedback!

    • @HowToHomeDIY
      @HowToHomeDIY  Год назад

      @Culbyj what is wrong with it in your opinion? These are just basic common mistakes that can be avoided.

  • @carlosmendez1047
    @carlosmendez1047 7 месяцев назад

    Man, you are an Angel!!! I had a breaker stripping as soon as I turned 2 lights on or plugged a TV to the wall. Watched lots of videos and ran into yours. One of my outlets neutral wire was left so freaking long by the builder contractors so the last time something was plugged in it moved it and touched the ground causing the fault. I trimmed it just like you suggested and BAM!! All good on that circuit again.

  • @charlesohlson4316
    @charlesohlson4316 9 дней назад

    Thanks mate, In the HVAC and this is a great reminder of things... Thanks for what you do, keep it going. I'm looking at changing a ceiling fan and also at time point if i do it might as well do upgrades to all in some areas to make it usb capable. 9:55 use the right tools is key......

  • @deadmanswife3625
    @deadmanswife3625 11 месяцев назад +6

    It's nice that you take the time to thoroughly explain things in this video. You do go into detail and you do cover all the bases I appreciate that. It makes me feel sure that I understand what you're saying. There's too many people that assume everybody knows these little details. Thanks again.
    Edited to say
    I certainly understand the use of Pigtails in many more ways than I ever did before which was I didn't really at all LOL.
    It was also especially helpful when you talked about the different types of drill bits.

    • @petegarro6024
      @petegarro6024 11 месяцев назад +1

      Pigtail, always Pigtail, if not outlets down the line will not have juice

    • @misscdog
      @misscdog 5 месяцев назад

      Your video was great. I love that I didn’t hear of a single ummmm.

  • @j.elliott4310
    @j.elliott4310 Месяц назад

    I like your video because you are calm, clear and concise. The explanations are thorough so the viewer fully understands why these common mistakes happen and how to correct them.
    I stay away from electrical because I always thought it was dangerous but this video makes me feel confident to tackle installing new outlets and switches in my home!!🙂

  • @jodihaas7709
    @jodihaas7709 2 месяца назад

    I learned more in these few moments than I did after years of working at a hardware store! So easy to understand. I have the confidence to replace my problem outlet, thank you!

  • @frankhenry2467
    @frankhenry2467 11 месяцев назад +6

    Great video! I'm in property management and do a lot of side work of all kinds. My rule is plumbing or electric inside the wall is done by pro's. A good friend of mine is a master and taught me the basics that you showed. Never hurts to have a refresher though! Thanks.

    • @toriless
      @toriless 10 месяцев назад

      In ground work is harder than simple in wall work.

  • @gwmattos
    @gwmattos Год назад +3

    A very professional and to the point video and I appreciate the information you gave because I just purchased a receptacle very similar to what you're showing and I have to install it this week and your advice was to the point and very helpful.

  • @markdahl8082
    @markdahl8082 4 месяца назад +4

    Great video. Years ago I updated my home outlets to more modern versions and was not aware of “reverse polarity” (AC isn’t polarized, right?). I discovered my error when I recently failed the home inspection when selling my home. As probability theory would predict, I had to go through and rework about half my outlets! I wish I had been able to watch this video back then!

  • @michaelferver5707
    @michaelferver5707 5 дней назад

    Great details! Thanks so much, for this level of explanation.

  • @drewkremer2609
    @drewkremer2609 Год назад +3

    Great video! As a rookie DIYer, videos like this are absolutely invaluable! Thanks!

  • @jtnelson89
    @jtnelson89 Год назад +8

    Thank you for this, I didn't know about that new type of bit. Phillips heads were designed to slip to limit the amount of torque that could be put on a fastener. I first encountered this working on vintage Japanese motorcycles and damaging lots of bolt heads. I finally found out that these heads are not Phillips after all, but rather JIS, which is designed not to slip, and got a set of JIS screwdrivers which make the jobs go a lot better. It seems that there is an electrical equivalent of a non-Phillips crosshead screw!

    • @JL-yo1du
      @JL-yo1du Год назад

      Copper is soft and should not be overly tightened, I have found Philips apply enough pressure.

  • @geraldwilliams5256
    @geraldwilliams5256 6 месяцев назад +1

    Learned two additional pieces of information about the outlets today. The guage marks on the outlets and how the rear connections are found to be unstable. Thanks.

  • @keninfarinato1177
    @keninfarinato1177 3 месяца назад

    Very well done! Your work was fully visible, and your explanations were clear and complete. Basics are so important. Thanks!

  • @ducamuk
    @ducamuk Год назад +4

    Love those ECX and combination bits. Had no idea they existed until now. Thanks for sharing your knowledge and experience. ✌️

    • @HowToHomeDIY
      @HowToHomeDIY  Год назад +1

      You are very welcome. Really glad to hear you liked it. Thanks a lot for the feedback!

  • @shawfestify
    @shawfestify Год назад +3

    It is fascinating whenever someone explains something that they know well, about an improper and proper--more safe way to do it. I appreciate that, even if I never install an outlet in a home! Thank you.

    • @epstein_isnt_dead7726
      @epstein_isnt_dead7726 Год назад

      You can tell from the first 30 seconds of the video that this guy is clueless. Just look at his pegboard. Dude clearly just went to home Depot to buy props for his video backdrops and has never used a tool in his life. He just watches Electrician U videos and poorly repackages that content into his own videos

    • @patriot692
      @patriot692 Год назад

      YOU are going to burn your house down Hahahaha! J-k, I saw that somewhere in these comments. But this guy in the video's Not a total dufe.

    • @HowToHomeDIY
      @HowToHomeDIY  Год назад

      Thanks I think? 😂 I find it hilarious that I’m clueless because someone thinks my tools are props. Instead of at least trying to talk about the content of actual subject matter. Genius lol

    • @HowToHomeDIY
      @HowToHomeDIY  Год назад

      Uh oh, someone got their panties in a wad. When did I say piggybacking off of a receptacle is okay? Some folks on here are amazing 😂

  • @lovelyletter7460
    @lovelyletter7460 7 месяцев назад

    Great video! I just watched this with my 8 year old son who started becoming obsessed with electrical and watching these videos since he was 3. He was explaining gfci outlets and “ground” to anyone who would listen! 😆

  • @JonathanPerez-vz5ei
    @JonathanPerez-vz5ei 7 месяцев назад +1

    I changed 3 outlets so far at home and made a bunch of these mistakes. Gonna redo them. Thanks for the great tips 👍💪

  • @risussardonicus8416
    @risussardonicus8416 Год назад +9

    Great video. Something worth pointing out, there are round cutouts at the base of the mounting tabs. They are to be used as wire strippers 12,14 gauge ,solid or stranded.

    • @gano7297
      @gano7297 Год назад +2

      VERY few brands have that feature from what ive seen.

    • @kb_100
      @kb_100 Год назад +1

      Eaton does but Leviton does not. In any case its not a great way to strip wires

  • @chucknahlik
    @chucknahlik Год назад +4

    I found this video very informative. I am not an electrician but an absolute DIYer and have changed out my share of electrical outlets. The most eye-opening for me where the new bits available for this type of project! Running out to the home improvement store right now!

    • @HowToHomeDIY
      @HowToHomeDIY  Год назад

      Glad you liked it. Thanks for the feedback!

  • @reallifechangingtruth7679
    @reallifechangingtruth7679 Месяц назад

    Your teaching is electrifying! Good stuff! The information connects right to the mental receptacle! Less chance of a short mental circuit that may cause a bad connection and possible information flow failure! There you have it! From Pst. MBJR. 2-3-24 at 10:48 A.M. Oregon Time. Get plugged in.....

  • @intherockies
    @intherockies Месяц назад

    I've changed a socket before but it's been years ago and my husband was there. Fast forward to now, I need a new plug-in and it's just myself and my 15 yr old grandson. I used this video and a few others to make sure I do it right and teach him the right way (yes main breaker to house will be off). I appreciate you sharing your knowledge with us.

  • @derekdeemie2074
    @derekdeemie2074 11 месяцев назад +3

    Thank you my man! I'm building a relatively large shed for my mom and your channel is going to help me out. Good stuff brother!

    • @HowToHomeDIY
      @HowToHomeDIY  11 месяцев назад

      You are very welcome! Really glad to hear you liked it. Thanks a lot for the feedback Derek!

  • @roberth9188
    @roberth9188 Год назад +19

    Super simple stuff- other than the double stack I’ve still caught myself doing all the other mistakes! Not good when you risk burning down your house, maybe with your family and yourself in it. Thanks for your videos, I’ll be checking through them time to time for instruction or reference before I get into projects👍🏻 I’ve learned the hard way 2 bazillion times that a quick second to watch and be sure I’m prepared can save some brutal headaches.

    • @HowToHomeDIY
      @HowToHomeDIY  Год назад +2

      Your are welcome. Really glad to hear when a video is able to help folks. Thanks a lot for the feedback!

    • @keithmarlowe5569
      @keithmarlowe5569 Год назад +1

      And don't think insurance investigators aren't trained to sniff out things like that to deny claim. That's why I hired a union master electrician that works on the side to wire my basement. Cheaper than an actual company, but covered by his license. The other reason is that amount of electric work is beyond my skill level.

  • @michaelgalland7985
    @michaelgalland7985 3 месяца назад

    Really appreciate how clear and thoughtful your directions are. Thank you.

  • @victoriavanburen8950
    @victoriavanburen8950 Месяц назад

    Thank you - I appreciate the clear video and detailed instructions.

  • @calebenglert692
    @calebenglert692 Год назад +11

    I don’t know everything but I was aware of all of this content.
    However it took years to figure all these little details out. I always want to learn more, and fear I may have been doing something wrong. Great video. Many people who are paying attention are avoiding a long hard learning curve. Definitely a High value video.
    Great job man.
    Keep them coming.

  • @Okie-Tom
    @Okie-Tom Год назад +3

    I didn’t even know about those “ECX” bits. Good info! Tom

  • @jennabryan1658
    @jennabryan1658 6 дней назад

    Thank you! Many pauses and rewinds and notes- thank you!

  • @sozofam2164
    @sozofam2164 27 дней назад +1

    Ver concise video and well explained [especially for seniors]. Thanks!

    • @HowToHomeDIY
      @HowToHomeDIY  13 дней назад

      You are very welcome! Really glad to hear you liked it. Thanks a lot for the feedback!

  • @51samiam
    @51samiam Год назад +26

    Great tips - As a DIYer I don't wire outlets every day so "best practices" never become "habits." I never knew why electricians didn't use the back-stab facility but now I do. Also the strip-gauge would save me either stripping more or cutting too long a tip off the copper.

    • @toriless
      @toriless 10 месяцев назад

      Unfortunately, "smart" switchers and dimmer so not have them, I can provide proof, but I have enough experience to guess anyway.

    • @rsvihla
      @rsvihla 9 месяцев назад +1

      The electricians who wired our house used the back-stab terminal.

    • @Effervescent_Smegma
      @Effervescent_Smegma 3 месяца назад

      Laziness kills.

  • @CupidStatFunt
    @CupidStatFunt Год назад +11

    Thanks for this, particularly the clockwise/anti-clockwise thing. I'm an occasional DIYer and knew about the hooks and trim length but never knew that the hook was supposed to go in clockwise. I'd randomly insert it in either direction and thought the reason the wire slipped out sometimes and stayed put others was down to poor quality control on the terminals. I've even wedged a flat head next to the wire to stop it popping out while I tightened. Thanks!

    • @TheBooze13
      @TheBooze13 Год назад +2

      Hire an electrician you’re going to burn your house down

    • @patriot692
      @patriot692 Год назад +1

      My pet peeve over the years has been: Seeing so many people NOT examining their own methods, NOT being safe. A fool leaves sharp tin or wires falling into roof insulation. A fool jacks up a vehicle WITHOUT tires blocked, emerg. brake On. I can think of a dozen more examples. I can accept humble suggestions from others. If I disagree, I explain the physics of Why. Seems like most women (that I've been around) "just want the damn thing fixed, & they want it done YESTERDAY! 🐷😵‍💫💩😠

    • @CupidStatFunt
      @CupidStatFunt Год назад

      @@TheBooze13 ​In my defense, I've never had an issue with the exception of this one thing - one thing that How To Home thought was a common enough mistake he made a video about it. Also, in case my words misled - the flat head screwdriver is only there while the electricity is turned off to ensure the wire doesn't slip as the screw tightens. It counters the effect of the screw pushing the wire out, and everything is securely held in place before the flat head is removed. Everything is then insulated before turning the electricity on and testing polarity/ground, then the electric goes off again while the outlet goes in the wall. One more go with the receptacle tester and a quick run round with the non-contact so I don't think there's any additional risks.

    • @CupidStatFunt
      @CupidStatFunt Год назад

      ​@@patriot692 A fool is one that doesn't learn. I reverse engineer most things I do, and often improve the process but this one thing got me. It's largely because I've only ever installed 8 outlets and 6 of them just happened to be the right way round, so, when I hit two that weren't I questioned the slightly cheaper outlets I'd switched to instead of myself. I observed the wire slipping out and devised a graceful lever mechanism to insist that it stay in place as I tightened.
      Talking of jacking up cars, the first time I ever changed a brake pad it took two hours for the first wheel but the last time I ever changed one, the second wheel, only took 15-minutes. I was barely 17 and, although the parking brake was of course on, I had no idea about blocking the tires at the time. The wind was blowing hard and my leg was totally fine because nothing happened but you almost thought it was going to be an interesting story.

    • @castironwitch
      @castironwitch Год назад +1

      I'm left handed and although I know this, I catch myself going the wrong direction or twisted wires together the wrong way then wondering why the wire nut doesn't feel right! Thanks for the reviews, helps alot

  • @fjp3305
    @fjp3305 Месяц назад +1

    Great, very helpful. I didn't know the gold and silver screws stuff.

    • @HowToHomeDIY
      @HowToHomeDIY  Месяц назад

      Really glad to hear you liked it. Thanks a lot for the feedback!

  • @trevorpark7768
    @trevorpark7768 Месяц назад

    This video was great. You got right to the point and explained everything so clearly.

  • @fantasticfamily5004
    @fantasticfamily5004 10 месяцев назад +4

    Thank you! A friend who does his own work. I saw the black wire was stripped more as you showed. He said it was okay. He just re-tightened.
    After he left, I turned off my electricity. Got my wire cutter, cut the tip off. Measured it like you demonstrated. We curved. And refastened. I feel safer now that I did this. This just reassures me that I myself can do this safely and cautiously. I also know that if I don’t feel comfortable not to do it and to bring an electrician in.. for me it’s always been better. Be safe than sorry.

    • @myobmyob2215
      @myobmyob2215 2 дня назад

      Wrapped new receptacle connection sides w electrical tape after RnR because GFCI didnt trip breaker didnt trip burned outlet and GFCI strip. Leave nothing to arc, nothing to chance.

  • @lory2622
    @lory2622 Год назад +3

    Thank you sir. I know this stuff pretty well but I am a DIY’r and almost every time, I learn something either new, or better. Thanks for the effort.

    • @HowToHomeDIY
      @HowToHomeDIY  Год назад

      You are welcome. Really glad to hear you liked it. Thanks a lot for the feedback!

  • @juanaponte2782
    @juanaponte2782 17 дней назад +1

    Thanks, very easy and explained. As a handyman I know that looks easy but I knew that I was doing something wrong every time whit the cable's and now that I saw this video I know what I was doing wrong.So thanks again 💪🔥💯

    • @HowToHomeDIY
      @HowToHomeDIY  13 дней назад

      You are very welcome! Really glad to hear you liked it. Thanks a lot for the feedback!

  • @markdemonte4546
    @markdemonte4546 26 дней назад +1

    Great video, I have to replace an outlet in the kitchen, thanks so much!

    • @HowToHomeDIY
      @HowToHomeDIY  13 дней назад

      You are very welcome! Really glad to hear you liked it. Thanks a lot for the feedback!

  • @InexplicableBill
    @InexplicableBill Год назад +35

    Great video man!! Son of an electrician here, Architectural designer by trade. I watched my pop do a lot of wiring as a kid and am a confident DIY electrician around my own home. I certainly don't know everything but love learning. The combination screw bit you showed at the end is an incredible innovation for electricians. I'm buying a set today!

    • @HowToHomeDIY
      @HowToHomeDIY  Год назад +4

      Glad you liked it. Those bits really do make things so much easier. Enjoy them! Thanks a lot for the feedback!

    • @jameskennedy673
      @jameskennedy673 Год назад

      👏👏👏for this video. Years ago I was taught that the black wire went to the brass screws, white wire to silver screws. I was also taught to be careful with electricity, it’ll earn your respect. I done away with our garbage disposal, which the on/off switch had a receptical also, I took it out put in a wall plug, put black wire to brass screws, white to silver, but no power, the breaker is on

    • @johndorian4078
      @johndorian4078 Год назад

      but do you really need that much torque......... you can cause just as much damage as good if you torque it to tight.

  • @Joe-xy9mq
    @Joe-xy9mq Год назад +3

    This is the best instructional video I have ever watched, and I have watched many over my 60 years. The camera work is perfect. Great closeups. Your speech is easy to understand and very well done! Awesome!

    • @HowToHomeDIY
      @HowToHomeDIY  Год назад

      Wow, thank you very much for the feedback. Really glad to hear you liked it so much!