I did my express cruiser back in 2020 still holding up great only 2 suggestions 1 always round your corners 2 before your final lay down & adhesion give it a spray of 3M heavy duty spray adhesive. Looks great mate!
great job mate. I'm doing my second boat shortly. I use Silkaflex 591 black, around all the seems, just for good measure, that water can not get underneath and start lifting the stickiness. Bit of extrawork though having to mask up the edges and then mask the floor. 3 or 4mm , Then when you peel off leaves a lovely finish.
Nice job. I think that looks great. An alternative installation approach could be to find the midline of the boat and place a panel there and then template out to starboard and port to complete. You might have an easier time of aligning the black lines that way? Let is know how it holds up.
Thank you for not glossing over the stenciling and measuring part. Too many videos speed through it and it's the most important part, good to see the actual speed of some of the difficult portions of boat. Came out great nice work. My only question is what about the screws you took out, wouldnt you want to seal them with something in case water seeps through?
Can’t believe y’all put carpet on offshore boats. The blood would be a nightmare. Not to mention all the damned snaps. Plan on putting the exact same foam on my twin vee. How has it held up thus far? You did a hell of a job.
Nice job. Just got a sea fox boat and looking to do this . Thinking of doing seating in the cuddy as well . Also they have a diamond pattern maybe for the dash.
The rolls were only 500mm wide so it would have made it difficult as the carpet was one large piece.Also, I wanted it to be a more accurate fit than the carpet was.
If you give the boat a real good clean it will stick.I used degreaser and acetone to clean mine but mine is fibre glass. Just check on a small area on your boat just in case the acetone reacts.
i install my brown and im not happy at all everytime when gets wet is a mess of paint from the eva foam look like brown dust when is dry everyting you bring aboard gets stain from it
@@Eltsinoz I understand that you say that it already has it but that’s not a reality. What kind of stain resistant in water resistant treatment would you use to make it? Let’s say more water and stain resistant? Because reality is that stains do occur often.
Still looking good . None of it is coming unstuck. There is the odd mark on it but would put that down to wear and tear. I would say it was a success. I think good preparation is the key and wash it down after any fishing baits or blood etc get on it . Will maybe do another short video soon. Thanks for the comment.
Won't last. I fish almost every day and my boat is under cover when not used and this stuff only lasts 2 maybe 3 years in Florida. It's disintegrating away.
I did my express cruiser back in 2020 still holding up great only 2 suggestions 1 always round your corners 2 before your final lay down & adhesion give it a spray of 3M heavy duty spray adhesive. Looks great mate!
Is it still holding up in your boat ? I’m planning to put it in my boat….
great job mate. I'm doing my second boat shortly. I use Silkaflex 591 black, around all the seems, just for good measure, that water can not get underneath and start lifting the stickiness. Bit of extrawork though having to mask up the edges and then mask the floor. 3 or 4mm , Then when you peel off leaves a lovely finish.
Good Job and looking forward to the update seeing how it holds up
Seems to be ok so far. 👍
Looks great! I like how you rounded all the corners
Thanks for watching
Great job you've just made there, I now feel it's going on my boat many thanks
Your welcome.Thanks for watching
Nice job. I think that looks great. An alternative installation approach could be to find the midline of the boat and place a panel there and then template out to starboard and port to complete. You might have an easier time of aligning the black lines that way?
Let is know how it holds up.
Doing an update video shortly mate.Cheers for watching
Thank you for not glossing over the stenciling and measuring part. Too many videos speed through it and it's the most important part, good to see the actual speed of some of the difficult portions of boat. Came out great nice work.
My only question is what about the screws you took out, wouldnt you want to seal them with something in case water seeps through?
@@Murfdigidy the screws were just for studs that held down the old carpet. Just dabbed some silicone on them
I have a 87 Grady White, and want to do this flooring also thanks for showing the process.
Thanks for watching
That looks mint mate. Good job!!
Thankyou.
Aguanta bien el paso del tiempo? Es facil retirarlo luego para poner otro nuevo? Un saludo
Hey mate thanks for the video - I’m about to do the same to my boat - gonna get the eBay Eva deck , would you still recommend? Cheers 👍🏽
Looks real good. I will be doing this shortly and this was informative.
Thanks for watching.
Can’t believe y’all put carpet on offshore boats. The blood would be a nightmare. Not to mention all the damned snaps. Plan on putting the exact same foam on my twin vee. How has it held up thus far? You did a hell of a job.
Still looking good after a year.Definitely worth doing.
Nice job. Just got a sea fox boat and looking to do this . Thinking of doing seating in the cuddy as well . Also they have a diamond pattern maybe for the dash.
Definitely worth doing mate
Looks great man!
Hard to believe this was your first one! Great job, your well skilled! How’s it holding up?
Seems to be doing well so far.
Well done! Looks great!
Looks great, I like it!
Thankyou
Thought you might have removed the chair bases to make it a bit easier,
Was worried about weakening the fixings but would have made it a bit easier….thanks for watching.
Great job
Thankyou.
Well done
Is that just a plastic drop cloth for paint that you’re using for template?
Slightly thicker than a drop cloth.Just bought a roll from local hardware store.
Is this stuff waterproof does it let the water lay under it.
Yes it’s waterproof and doesn’t hold water.
Can’t u use the carpet for the pattern?
The rolls were only 500mm wide so it would have made it difficult as the carpet was one large piece.Also, I wanted it to be a more accurate fit than the carpet was.
Really nice work
Thankyou
Just wondering where did you buy the plastic roll thanks
@@hanshahn3145 got it from Bunnings hardware store.
what is the material the boat deck is made out of? plastic? my boat deck is plastic and Im trying to figure out if this stuff will stick to it or not
If you give the boat a real good clean it will stick.I used degreaser and acetone to clean mine but mine is fibre glass. Just check on a small area on your boat just in case the acetone reacts.
Whats the name if the company you purchased from?
@@gadirtracer247 www.yarrasupply.com.au/products/eva-foam-boat-flooring-grey?variant=39302458736722¤cy=AUD&srsltid=AfmBOopXvrK7Qk_ksKNGZwpd-tYtWypXg5XujSJ_56xcf2m89iNoXDXcl30
i install my brown and im not happy at all everytime when gets wet is a mess of paint from the eva foam look like brown dust when is dry everyting you bring aboard gets stain from it
Not sure what foam you used but I’m not having this problem
Nice job
Thankyou
$22sf Canada texdeck
What do you use to make it resistant or proofing to water and stain?
It’s already water and stain resistant.
@@Eltsinoz I understand that you say that it already has it but that’s not a reality. What kind of stain resistant in water resistant treatment would you use to make it? Let’s say more water and stain resistant? Because reality is that stains do occur often.
@@user-ue1gf7im7m There is a few products you can use if you google it. Haven’t used any so couldn’t comment on how good they are.
How’s it holding up?
Still looking good . None of it is coming unstuck. There is the odd mark on it but would put that down to wear and tear. I would say it was a success. I think good preparation is the key and wash it down after any fishing baits or blood etc get on it . Will maybe do another short video soon. Thanks for the comment.
Won't last. I fish almost every day and my boat is under cover when not used and this stuff only lasts 2 maybe 3 years in Florida. It's disintegrating away.
If it lasts that long I would be very happy.I still have the templates so I will just replace it. Thanks for watching.
That’s a good time frame for only 260 of material ..