Just when you thought we own crap cars, today we introduce this shit box to the mix. We fully build this this thing from start to finish in one episode. Shes gonna go.
Where did the rods come from??? I need to know for my turbo N16. I'm running everything Haltech in mine as well. Been getting quotes from the US about getting custom Carrillo rods and Ross Racing pistons. If I could find some rods that already fit, that would be AWESOME!!!
@xplore7359 Not sure yet man. If all goes well, I'll be ordering them this arvo or tomorrow. I currently got Ross Racing Pistons making me custom forged pistons though so that's working out thus far. 👌
Absolutely fucking badass ! when you get that notification & you know the lads have been cookin ! 😎 Camp Dogs !!!! sick edit lads. dying to see the shake down 👍🏽
Hahaha fuck me it’s always the slapper builds where you get away with giving zero fucks assembling or checking any clearances , the screw driver for the rings had me crying 😂 , I would never do an oil change on that motor, it’ll let the magic out
Nice love the build guys but I own a 2003 Nissan bluebird syphy and I just changed my fuel pump and the fuel gadage stop working what exactly u think is the issue?
What pistons and rods were used. I know the eods were aftermarket (what brand) and were the pistons stock or custom ? Head studs? Gaskets ? Please teach me !!!
Stock pistons, reused the rings, rods were on eBay. It was very hard to find any listing for qg18 but it turns out the ga16 rods are identical so we got those and they work fine
FINALLY….THE TIME HAS COME😈, it was about time the N16 gets put on the map. I got the early model version aka the small light model with the QG16 de. Love this episode guys, awesome job, although I would warn you that the timing chain, cam and crank sensors are an issue with this car after like 170,000km. Hopefully if it gets enough popularity, us QG boyz can get good performance parts👀🙏
@@MattBerrymotorsportAt around that 170,000km mark the timing chain metal is known to expand, elongating the overall timing chain’s length by a couple millimeters, and it would make the engine sound like it misfiring a bit, had this happened to me before. If the engine has been reasonably taken care of and is under 120,000km, you should be fine but just to be safe, try and get an oem replacement if possible, before….you know….timing chain deletes itself💀🥲
Get yourself a isky o-ring tool and oring the block with stainless wire, then run a stock composite head gasket. You'll blow a hole in the block before the head gasket fails. I o-ringed my BMW block at home it's easy as.
Boys this is gonna smoke Nicks starlet, its nuts!
Hope there's an LSD in the works or the only thing it'll smoke is one wheel up to 200kmh lol
wont it smoke that auto trans?
@@exvilsseems to be holding up
😅p9c@@tmmtmm
We lost the Nissan pulsar in the 90s. That thing looks like a Toyota Corolla.
Hi
The Starlet is shaking in its boots
Proper RUclips build
Awesome, rough as guts but awesome.
haha what a ripper! i need to drop an AU falcon off for you bloke to turbo for me!
install a large transmission cooler with fan
Where did the rods come from??? I need to know for my turbo N16. I'm running everything Haltech in mine as well. Been getting quotes from the US about getting custom Carrillo rods and Ross Racing pistons. If I could find some rods that already fit, that would be AWESOME!!!
Straight off eBay to suit ga16 engine
End up having any luck Cody? I know GA16 rods will fit but some require heavy notching of the girdle and block to clearance.
@xplore7359 Not sure yet man. If all goes well, I'll be ordering them this arvo or tomorrow. I currently got Ross Racing Pistons making me custom forged pistons though so that's working out thus far. 👌
Mean videos
I'd trust anyone with an Australian accent!
I heard these engines had problems with weak cam chains.
I guess we'll find out if they put 40psi through it.
Only one way to find out.
@Camp Dogs what rods are you guys using??
EBay
ive been checking, noting under the qg specifically
ill give u guys my n15 sss pulsar to turbo LOL
Man i love to see regular cars making powah
In 🇹🇹 we call n16 Almera, pulsar are base off b14, nice build 👍
Men at work!
Down under.
Gave me a bite , of a Vegemite sandwich 😂
😜👍🇦🇺
Love the qg18de motor its the same engine pretty much as my ga16de. So cool to see this
Absolutely fucking badass ! when you get that notification & you know the lads have been cookin ! 😎 Camp Dogs !!!! sick edit lads. dying to see the shake down 👍🏽
came for a sunny gti-r got spammed with some shit music at the start then got trolled with the joke "pulsar"..
You really got got good aye?
Hahaha fuck me it’s always the slapper builds where you get away with giving zero fucks assembling or checking any clearances , the screw driver for the rings had me crying 😂 , I would never do an oil change on that motor, it’ll let the magic out
I know right! All the cars we take time on to do properly have nothing but dramas!
Slapper builds for the win 💪💪
Nice love the build guys but I own a 2003 Nissan bluebird syphy and I just changed my fuel pump and the fuel gadage stop working what exactly u think is the issue?
Hey bro size intercooler pipes do u use on a 5efte
big up de dawgs them for building a beast real 🇹🇹men going smile seeing this 🤣
Should have used stick car
Absolute champions!
Keep up the exquisite engineering….. love it!
Wear ear plugs or ear muffs when using an angle grinder when your older your ears will thank you keep up the awesome content
I wish you guys would fix my car 😅
Fuk yeh. Got 2 of these pulsar at my block haha
40psi is a lot of boost for 500hp. 😱
We will give it all it needs 😂
Got to love the attention to detail that went into this build. 😂😂
What pistons and rods were used. I know the eods were aftermarket (what brand) and were the pistons stock or custom ? Head studs? Gaskets ? Please teach me !!!
Stock pistons, reused the rings, rods were on eBay. It was very hard to find any listing for qg18 but it turns out the ga16 rods are identical so we got those and they work fine
We used the cheapest head gasket on eBay, $50
Re used the stock head bolts
1.8 litter I thought it was 2.0?
FINALLY….THE TIME HAS COME😈, it was about time the N16 gets put on the map. I got the early model version aka the small light model with the QG16 de. Love this episode guys, awesome job, although I would warn you that the timing chain, cam and crank sensors are an issue with this car after like 170,000km. Hopefully if it gets enough popularity, us QG boyz can get good performance parts👀🙏
Great info, we already had problems with the sensors and have replaced them. What can we expect to go wrong with the timing chain?
@@MattBerrymotorsportAt around that 170,000km mark the timing chain metal is known to expand, elongating the overall timing chain’s length by a couple millimeters, and it would make the engine sound like it misfiring a bit, had this happened to me before. If the engine has been reasonably taken care of and is under 120,000km, you should be fine but just to be safe, try and get an oem replacement if possible, before….you know….timing chain deletes itself💀🥲
What pistons did they use I need some for my qg18 build
Stock pistons
We are currently on 26 psi and going over 30 soon
Pistons out turbo the car and didn’t even jack it up once😂
All my life I known this car as Nissan Sentra
Probably the same thing but we don’t have them badged as Sentra here
your bead roller sounds like a wookie
😆
Nice video this is fkn sick, how much will it cost me to come down and get mine done for similar speed ❤🙏🏾🔥
i swear i am loving this so funny to good
love this, think am a build one ....would love it if u share the build info and wire diagrams
Wiring diagrams can be found on google. Type in qg18 wiring diagram text files and click the link.
1000s of pages of the entire car
Another banger from the Legends!
YEAH THE BOYS !!!
What connecting rods you guys used
steppin it up with the editing.. hammer shot and air box shot were mint.
Update time boys
Drags this weekend, currently on 30 psi
wicked build!
Where did you buy the connecting rods
Great video. Can't wait to see it turned up
Can you make a atomatic car have a turbo
Some of the best content on my feed atm!
So good 👍
So good
I have a Nissan blue bird sss
Where'd you guys source the rods and pistons from for this build? I can't find anything in Aus.
Stock pistons and we found a set of rods of eBay. I tried finding the listing for another guy but old mate only had one set.
@@MattBerrymotorsport bugger, thanks for looking.
what rod and piston did you guys use ?
Chinese rod, stock piston
now do you think i can put one of those on my ga16de and make 400?
I think so
Is it Sam engine
Bang on hood cutouts!
In Australia we call it a fluke
twin engine pulsar
After tonight’s tuning on the hiway it would definitely be sick. Drives way better than a starlet 😂
@@MattBerrymotorsport just run it berry crank the channel up. time to turn up the flame
Hi I am val
Get yourself a isky o-ring tool and oring the block with stainless wire, then run a stock composite head gasket. You'll blow a hole in the block before the head gasket fails. I o-ringed my BMW block at home it's easy as.
Stock as looking sleeper until you wake it up TTTOUGH 🦾