Hi Francisco, Im Jose from Spain. First of all congrats for your amazing video, its very clear. I have the same problem in my BMW X6 F16 year 2016. I would like to know where can I buy the seals, solenoids, turbine sensor, etc... Do you sell these components? or Where can I buy these components to repair my car? What precautions should I take to replace the turbine sensor? Thank you Francisco and congrats again for your amazing video. Thanks
Gary my 02 745i 4.4 6hp26 does run ok but 4,5 does hard bump at shift and no 6 gear code p0735 I found lowww oil and tube seals flat hardened like rock, and when fail safe mode appears it will go into Park but e shift didn’t show P it will stay at N flashing
Hello, I have a BMW 550i 2008 e60. The car could not be driven, I connected a scanner to it and it gave me a code that one of my transmission solenoids was damaged. I removed the mechatronic unit, tested my solenoids, found that one was actually damaged, replaced them all anyway, replaced the signal bridge that goes on top of the valve body, replaced the 4 sleeves, and the transmission connection sleeve. I install everything in the back, the car drives but it doesn't go to park. I tried the old Park solenoid (green solenoid) and it worked. I decided to install that old solenoid thinking that the new one was defective and I still have the same problem. I connected a matco maxlitea scanner to it and I have a 507D EGS error: Parking Gear Incorrectly Disengaged. What do you recommend I do? The transmission has enough fluid, it is freshly changed fluid
Hello Francisco, I have 2011 BMW 740, I had the turbine sensor code, I sent the mechatronic to a guy to repair. Not the turbine sensor code is gone, but i have code 400671 Position Valve Malfunction, I got brand new Selonoids and still throws the same code. What valve is this?
Seems exactly what I am experiencing with my E61 525i -07. It came during this last winter when I let it stand while driving another car during the winter. I started the BMW every other weekend and after a few months I noticed that it kind of slipped on the reverse gear and then let go to "P". For now, I can only get into "D" if I am fast after starting the car. I also started noticing leakage under the gearbox. It was dry underneath when I put it to winter rest. Maybe I have lost too much automatic fluid so it can't activate the gears....
Hi please need your help, my E60 525i brings Transmission fault and the signals P,R,N,D don't show on the dash causing car not to start what could be the problem
Hello Francisco, I have a problem with my BMW E60 520i 2004. Surprisingly even at idle when I switch it on, it will run, and then after about 10min, generate a transmission fault, without even moving. Sometimes when I switch it off, and switch it one, I get the error "Park P not engaged", with a symbol of a car with two arrows above pointing in opposite directions; and it refuses to start until after some time, possibly it resets itself. Sometimes, I would be driving, and then after sometime, it generates that transmission fault problem; When I put into park, and then drive, it drives in safe mode until I get to my destination, sometimes I dont even get to my destination, it goes into neutral until after some times when it resets. Can you help what could be the problem with this type of behaviour? Thanks
Hola Francisco saludos desde Colombia tengo una transmisión zf8hp45 con el siguiente código 421462 sensor De revoluciones de la turbina el vehículo no hace las marchas y se coloca solo en P en ocasiones no da ninguna marcha
Hi there, i have 07 750li with zf6hp26 trans,my vehicle start going into park from drive after vehicle worm up,will not do it when it's cold, error code iam getting is 4E89 SV 1 or SV 2 mechanically jammed.Have you seen a code error like this. I replaced all mechatronic sleeves and all solenoids, followed fill procedure engine off ,engine running at 40c .Reset adaptation,still having the same problem.I recently replaced the valvebody with used one but i used my old TCM module installed on it. because I couldn't flash the one that came with the used valvebody ,still have same problem same error code. could you please help me with this problem what it could be.thanks.
I have an automatic car is doing funny things 118i bmw F20 5 door First when selected Drive or Reverse it would just jump back on its own into Park. Now its not doing that anymore. Now when i select reverse it goes into reverse and as soon as i get close to something it was sound an alarm, but when i select Drive it goes into drive and goes forward . the alarm disappears but the reversing information is still on the dash screen even when i put in Neutral. Hope i can get some help from you or someone on this chat
Thank you I have a shop and you are a great HELP. ADG AUTO MONROE N.C
Hi Francisco, Im Jose from Spain. First of all congrats for your amazing video, its very clear. I have the same problem in my BMW X6 F16 year 2016. I would like to know where can I buy the seals, solenoids, turbine sensor, etc... Do you sell these components? or Where can I buy these components to repair my car? What precautions should I take to replace the turbine sensor?
Thank you Francisco and congrats again for your amazing video.
Thanks
The video was not very explainatory
y
Gary my 02 745i 4.4 6hp26 does run ok but 4,5 does hard bump at shift and no 6 gear code p0735 I found lowww oil and tube seals flat hardened like rock, and when fail safe mode appears it will go into Park but e shift didn’t show P it will stay at N flashing
Cange the meg tronic bro
Time 2:31 June 17 2024. I have a 2011 bmw 750li. How do I remove the turbine speed sensor from the tcm? Thank you.
Wend you change the part do you need to reset the computer??? Yes or not?? My BMW is a 2009 528i
Hello, I have a BMW 550i 2008 e60. The car could not be driven, I connected a scanner to it and it gave me a code that one of my transmission solenoids was damaged. I removed the mechatronic unit, tested my solenoids, found that one was actually damaged, replaced them all anyway, replaced the signal bridge that goes on top of the valve body, replaced the 4 sleeves, and the transmission connection sleeve. I install everything in the back, the car drives but it doesn't go to park. I tried the old Park solenoid (green solenoid) and it worked. I decided to install that old solenoid thinking that the new one was defective and I still have the same problem. I connected a matco maxlitea scanner to it and I have a 507D EGS error: Parking Gear Incorrectly Disengaged. What do you recommend I do? The transmission has enough fluid, it is freshly changed fluid
I changed the valvebody because I had a bad turbine sensor and shift solenoids but it still runs poorly. Would I have to replace or reprogram the tcm.
Hello Francisco,
I have 2011 BMW 740, I had the turbine sensor code, I sent the mechatronic to a guy to repair.
Not the turbine sensor code is gone, but i have code 400671 Position Valve Malfunction, I got brand new Selonoids and still throws the same code.
What valve is this?
Question: 2007 750 Alpina 120 K. No codes, no noises, no shifting, if put in D feel the kick and then no go, no reverse neither. Please advise.
Seems exactly what I am experiencing with my E61 525i -07.
It came during this last winter when I let it stand while driving another car during the winter.
I started the BMW every other weekend and after a few months I noticed that it kind of slipped on the reverse gear and then let go to "P".
For now, I can only get into "D" if I am fast after starting the car.
I also started noticing leakage under the gearbox. It was dry underneath when I put it to winter rest. Maybe I have lost too much automatic fluid so it can't activate the gears....
Hey bra, i have added the transmission fluid on my BMW 745li 2002 , but it’s not engaging , do you have any suggestion?
Thanks frn
Hi please need your help, my E60 525i brings Transmission fault and the signals P,R,N,D don't show on the dash causing car not to start what could be the problem
If water get inside the transmission can it damage the transmission
I just emailed you on this issue.
Thanks,
Nick
Hey buddy, so my question is, how do you remove that brown piece that has the sensor from the whole unit to access the wiring part to weld???!
Goo day, did you by any chance figure it out? I noticed some clips, but they look so hard to unclipped.
Hello Francisco, I have a problem with my BMW E60 520i 2004. Surprisingly even at idle when I switch it on, it will run, and then after about 10min, generate a transmission fault, without even moving. Sometimes when I switch it off, and switch it one, I get the error "Park P not engaged", with a symbol of a car with two arrows above pointing in opposite directions; and it refuses to start until after some time, possibly it resets itself. Sometimes, I would be driving, and then after sometime, it generates that transmission fault problem; When I put into park, and then drive, it drives in safe mode until I get to my destination, sometimes I dont even get to my destination, it goes into neutral until after some times when it resets. Can you help what could be the problem with this type of behaviour? Thanks
Hola Francisco saludos desde Colombia tengo una transmisión zf8hp45 con el siguiente código 421462 sensor De revoluciones de la turbina el vehículo no hace las marchas y se coloca solo en P en ocasiones no da ninguna marcha
Hola, tengo el mismo problema en mi BMW X6 F16, como conseguiste solucionarlo? Gracias
I noticed that you’re working on a California vehicle where exactly in California are you?
Where you located.
I want to bring my 750li to you
Hi mate I put brand new mechatronic and now I got no engine run no gears plus got code faulty
E09400
And E09410
Any help
Thanks
Hi there, i have 07 750li with zf6hp26 trans,my vehicle start going into
park from drive after vehicle worm up,will not do it when it's cold,
error code iam getting is 4E89 SV 1 or SV 2 mechanically jammed.Have
you seen a code error like this. I replaced all mechatronic sleeves and
all solenoids, followed fill procedure engine off ,engine running at 40c
.Reset adaptation,still having the same problem.I recently replaced the
valvebody with used one but i used my old TCM module installed on it.
because I couldn't flash the one that came with the used valvebody
,still have same problem same error code. could you please help me with
this problem what it could be.thanks.
Francisco I need your help to diagnose this problem on my car How can I contact you???
What do it cost for that job
Very useful video 🙂
Need help can u refer me to someone who can whip clean an program my valve body I live n new jersey...
Where can I email you or call you? I am close to Fontana
I have an automatic car is doing funny things 118i bmw F20 5 door
First when selected Drive or Reverse it would just jump back on its own into Park.
Now its not doing that anymore.
Now when i select reverse it goes into reverse and as soon as i get close to something it was sound an alarm, but when i select Drive it goes into drive and goes forward . the alarm disappears but the reversing information is still on the dash screen even when i put in Neutral.
Hope i can get some help from you or someone on this chat
Please anyone if you can assist please do
code is 400625 but ur title says 600625. Easy fix to get more hits.
I emailed you on this .please check thank you
얼마인가요 ㅜㅜ
He can’t read
I have slam in my 2006 530i bmw transmission when it goes in over drive
Do you have a direct phone number?
How come you never reply, I have the same car and I would like to being it to you can you email or reply to please . . Thank you
How to contact you