This is absolutely the correct way to mount. The distance between then depends upon which frequency you want to receive. More the distance between then the better it is. Mounting at +-45 degrees 90-0 degree also fine to achieve diversity or MIMO. Thanks.
I assume the original external antennas for the router was designed to transmit signals both for wifi and for 4G. Will the local wifi quality be poor when replacing both omni antennas with directional 4G antennas? Is it possible to just replace one of the 4G antennas, and how will the wifi and 4G quality be affected by this?
You have set antennas right because theya are 90 dgree for each other and 4g signals travel in mimo(multiple in multi out) which are perpendicular to each other
silly question but have you tried to swap the connecters going into the router, I found if i have one ariel on top and one below and i try the ariel sockets either way round one way will be faster than the other if you see what i meen
So Router does not need antenna inside Room, to transmit wifi, are both antenna that originally come with router are for receiving 4G signal, can this also be done with TPLINK MR200
Do you really need this antenna while you have the cellular towers just about 100 meter away from you? This makes me feel it’s might not work if I’m really really far away from the tower.
Sir plz tell me will it work to bihar rural areas.? I'm getting almost 7-8 Mbps want almost 20-30 mbps for my work please help me I should buy or not ?
hahaha i love this guy the right guy. i am connecting 3dbi antenna to a bobcat hnt miner (crypto) my cable is 10meters(25ft) where do i place the booster and what type please?
Im using only 1 parabolic 18dbi antenna in my mr6400 and the other is the stock atenna. So far it’s working fine. Planning to get the mr600 and i intend to use only the same parabolic antenna i have. Will that work?
5km is far, I guess Yagi should work, but it may be costly to get two of those. What is signal strength that you get now and are you at the direct line of sight from the cell tower. If you are then you can try the lpda as well provided you get marginal signal strength now.
@@diyIndia I'm not too sure about yagi antennas, they have good gain but narrow bandwidth. If you get two for two different frequencies you'll only be able to use inter-band aggregation (i.e. different bands) and not intra-band (same band) because each one will be polarised in one direction and won't pick up the other polarisation on that same frequency. You might be able to use just one frequency for both antennas, but then you can't use inter-band aggregation. LPDAs are more flexible because they're wide band and should allow both, but at the expense of lower gain. Also you'll never get 25dBi gain from a yagi! A better approach might be to use a flat dual polarised directional antenna like a Poynting Xpol2 and mount it in place of the feed horn of a satellite dish, there are youtube videos of people doing this and getting some very good gain. It's difficult to know which approach is best, it'll depend on your tower and what the aggregation capabilities of your router are as to what setup gives the highest and most reliable speeds.
How did you connect dual antenna to the router? Did you any T connector. Because the router has 2 antenna, but 1 is for 4g and another for wifi. Curious to know
if you insert an airtel sim and select lte band 40, it aggregates with two band 40s , y could easily achive speeds up to 100mbps, i get these speeds on my mobile if i stand this close to the base station please do try airtel and jio in this one and update.......
Yes I do use airtel. Band 40 ca does not work in this beta firmware I believe. For me with Airtel only band 3, band 40 work on CA. if am only connected to band 40 in airtel with these antenna I easily reach 75mbps. But upload is only at 5 and 6 Mbps which is why am using vodafone. With CA 3,40. I get upload of 15 Mbps and download of 30mbps, but the router does not lock CA for long. I have to restart to lock it again, am waiting for stable firmware. The beta is buggy for now
I bought an external yagi antenna from the internet. It works very well on an old router from huawei, but doesn’t work on newer models, like b310 or newer. Sometimes it doesn’t work at all, and orher times works interrupted, so that it screws up all the internet speed. Do you know why newer routers won’t work with my antenna?
you would need a direct line of sight, if there are building then the signals will be reflected by the walls. if you get good signals then you try the patch Antenna or Omni directional Antenna mounted little higher.
Dude your work is awesome , I own a Mr 600 Router 4g+ works till noon and after that Whatever I try band locking dosen't work at all will this work although my reception is Excellent with 100 % coverage using a vi sim
If you already are getting 100% reception. It is not worth buying this.. do not spend this, it will work only if reception is low. For band lock use the beta firm ware. If you already have band lock and if router fails to hold it on, just restart it.
@@diyIndia i tried restarting it after choosing the bands even then it does not hold onto it , this is the v2 of the mr 600, replaced it once even then it dosent work . i found that the snr value is involved with the 4g+ and speeds , snr of 25 and above is giving me speeds of 70 to 80 mbps but as it drops to 13 to 15 speed goes down to 20mbps . whereas on my mobile with the same sim card getting 4g+ almost all the time and speeds always greater than 70mbps and early in the day 100+mpbs which is pretty insane . so will this help me improve the snr value or omni is better ? there are good number of towers in my area .
I always wondered...so can you confirm that when only one cable is drawn from the antenna, the latter should be connected to the port near the SIM slot?
Should i go for this? Bcoz i facing internet fluctuations (wifi disconnection) problem in my one month old tp link tlmr6400... Does this problem occur in this model too? Or this is just the network issue rather than device issues?
I have not faced any wifi disconnection issue. I have faced internet not connecting issue that was related to network, but no wifi disconnection. Did you try resetting flashing the firmware again?
I have a TL-ANT5819MS and I have the Base StationWBS510 for it. My problem is my router(TL MR6400) doesn't work with the antenna. What router do you have that can use a 4G sim card and work on the same frequency(5GHZ) as the antenna and base or Any advice or plan for them to work.
I m not sure I was able to understand that clearly, You need your router to work on 5 GHZ (Given out by the base station) and 4G data connecter to your router (which uses the ANT5819MS antennae ) ?
Hi, 1) I am using MR6400 though the router won't support CA it is necessary to buy 2LPDA antenna or one is enough? 2) 5m cable is suitable for two storeyed building rooftop to ground floor? 3) whatever the network in band 40 w/o CA the upload speed is very low like 2mbps by fixing this antenna will improve speed?
Hi, even though your router does not support CA I would suggest you to get two antennas this will help. 5meter would not be sufficient for the length which you mentioned. I would suggest you to run a length of cord or rope then measures to get accurate length. Even I have less upload speed in band 40, it's always been less than 2mbps but after fixing. It increase to 6 to 8 mbps, yes that's not great but I guess that's how much my base station supports in band 40 in my area.
The only visible repeater tower im connected too is 26 km away and getting 68-69 signal strength, Is there a way to improve the signal from my antenna to repeater tower?
It‘s already very good, i‘m like 3-4km away from the cell tower and my signal strength is about -80 to -110dBm on my mobile phone. Maybe there‘s another cell tower you are connected to, you can find that out with Cellmapper.
Thank you for the video. Would you please share the details where you bought he LPDA and cables? I have already ordered Mr 600 and require the LPDA setup like yours.
Depends on the deal in amazon. I saw it was selling for rs8499 and on top of that you also get some banks discounts . If you want to wait for an Amazon sale then you might get at a cheaper price.
Hello! Please tell me as you have connected the external antennas, how the router gives Wifi.. is it that it has to be again connected to Wifi router through LAN!
Hi, I have a doubt what if I use one internal antenna and one external antenna, can I do carrier aggregation? Like say internal antenna on band3 and external antenna on band 40, will that work? Can anyone help me here?
Which kind of antenna is good for the area which is far away from tower and also forests nearby. I get low connectivity .Now with route r placed outside I usually get 600kbps to 3 mbps. Will omni directional , or directional antenna help(MIMO ,or not MIMO) ,patch or panel antenna help in this case
Hi , I stay away from tower around 2-3kms. There is no direct visibility at my home. If I move around 500m the tower is visible. Which type of Antenna do you recommend?
Hey just purchased a to link mr600 , using it with an airtel sim . Which external antennas would you recommend . Also should I install one antenna or two ?
There is almost close to 4k difference between the prices, now you would need to decide if you are in spending extra 4k on LTE advance which is CA, now this is going to help you get better speed if the network provider supports it. The CA works on MR600 and MR600 has more supported band, but most band supported in INDIA are also supported in MR6400. It boils down to two things. Do you need CA and cost. If you can afford it get mr600
Hi sir, just wanna ask, currently I'm using modem TP-Link mr-6400, just done upgrade the firmware & have band for select, if use this signal booster can get higher speed? Thank you
I am staying approximately 1-2 kms from the tower, in this case, should I use the antenna's that you are using or the Omni-directional antenna's? Please reply.
These antennas are cheap compared to omni- directional antenna. If the tower is in line of sight (That is, if you could point this antenna directly to it) you will get good results.
Suppose I have 1 Mbps as the maximum internet speed available around my area. By installing the antenna and tp link router, will I get a better internet speed? For example: in your case, say you are getting 5Mbps inside your room, 10 Mbps on the terrace. Will you get more the 10Mbps in your room?
Internet speed depends on lot of factor. If you are already getting good quality signal and if your speed is only 1mbps then it is because of the network tower. Even if you get a tplink and antenna it won't help. Its for people who have less signal In there place. Check the comments to see if anyone has benefited based on your situation.
I am living in ground floor in a 3 floor building so if I keep the antennas in top floor , will I get wifi signal to ground floor or else I think my neighbours in 3rd floor will get better signal than me so what shall I do ?
What you could do is fix antenna on the terrace and run your cable to the ground floor and connect it with your router so that you can get wifi signal in ground floor. Antenna is used only for you 4g network.
I would Highly recommend that and it works well during heavy rain I had not faced any issues
3 года назад
The antennas should be grounded because electricity tries to find the easiest path to ground. Otherwise, the current would flow through the router and destroy something with a high possibility. And yes, it still should work during heavy rain, it‘s only a issue with mmWave and WiFi 2.4 GHz.
Hey there. The external antenna is only for 4G lte signals and not for wifi. I connected the antenna which are placed in the terrace and the MR600 has a built in Antenna for wifi inside the device and the device is placed inside my room. hope this clarifies.
@@diyIndia that information is very hard to ascertain from the manual and all online details. I too thought the LTE antennas also did internal WiFi. Thanks for clarifying.
Hello bro, with internal antenna usage i see a download speed of 30mbps and upload speed less then 1mbps. Do i need to purchase two lpda outdoor antenna or one antenna will do. I am working from home, cannot take chances. Please suggest.
Hey guys, I have installed one external antenna and one stock antenna to the MR600 router. But results were bad when to compared to original stock antenna. I purchased OXYWAVE external 4G lte antenna but it's not doing great for me. Any suggestions pls. Thankyou
I m not sure about radio technologies or whether single antenna might work for you, but what I could tell from searching the internet we need to have antenna setup as done in the video for better signal reception. Along with that the LPDA antenna must be in line of sight.
Make sure to plug external antenna connection to MAIN port and stock antenna in AUX port of router, but for optimum performance always use same type of antennas for correct MIMO configuration.
Hi. Will it work with TP-Link MR100 and 3g coverage?
3 года назад+1
Yes, to my knowledge you wouldn‘t even need 2 antennas. But also check, if your ISP will shut down 3G because in many countries it will be replaced (or is already replaced) by 4G and 5G. Also, 4G low band may be faster.
Check out YAGI at : ruclips.net/video/mfEHBX4gYZA/видео.html
Check out OMNI at : ruclips.net/video/f16a2_0HB24/видео.html
Can u share to me what cable type u use ..coz my cable connector to tenda 4G09 not suit it to large
@@road00mmr87 bro you have you purchased these 2 LPDA anteena from above seller Akansha singh?
bro you have you purchased these 2 LPDA anteena from above seller Akansha singh? How is her behaviour?
This is absolutely the correct way to mount. The distance between then depends upon which frequency you want to receive. More the distance between then the better it is. Mounting at +-45 degrees 90-0 degree also fine to achieve diversity or MIMO. Thanks.
Perfect. Thank you.
Hi abhijeet, plz make a video of your antenna set
Hi abhijeet, plz make a video of your antenna set
@@diyIndia If you mind, could you explain what he said above, please? thanks
Thanks for video... I have followed this and install setup. now able to gain 15mbps speed (earlier 1mbs airtel 4g).
Sach me kya
I use the same Router and Poynting 4g-xpol-a0002 !! Much better signal and I'm miles from the towers !!
I assume the original external antennas for the router was designed to transmit signals both for wifi and for 4G. Will the local wifi quality be poor when replacing both omni antennas with directional 4G antennas? Is it possible to just replace one of the 4G antennas, and how will the wifi and 4G quality be affected by this?
Signal is strong out door but is weak indoor. Tower is not in line of sight. What u suggest? Which antenna should I go for?
You have set antennas right because theya are 90 dgree for each other and 4g signals travel in mimo(multiple in multi out) which are perpendicular to each other
Lol
If I'm only using 1 antenna, do I need to tilt it?
It's been 2 years now.. How It's performing? Still worth?
Where do you have bougth these antennas?
Hi bro..can u share me website link where u r checking these data. I am using one 12dbi LDAP but not getting more than 6Mbps
Hi, My home is 5km away from cell tower does it work for me to get good internet speed?
Is this have a manual selection for "Band Locking" or "Change Band"?
Did you find optimised Antenna setting,like you mentioned 45 degree or pointing towards 2 different tower etc.
Sorry, I did not have time for it, I will be doing it soon.
Why are you using 2 yagi antennas? Isn't 1 of the connections on the router for wifi?
silly question but have you tried to swap the connecters going into the router, I found if i have one ariel on top and one below and i try the ariel sockets either way round one way will be faster than the other if you see what i meen
Why you have choosen LMR200 CABLE over other cables like RG CABLES
To be honest there is no specific reason why I went with lmr200.
Was there any setting changed within the archer mr600 modem to work better with external antenna
So Router does not need antenna inside Room, to transmit wifi, are both antenna that originally come with router are for receiving 4G signal, can this also be done with TPLINK MR200
Do you really need this antenna while you have the cellular towers just about 100 meter away from you? This makes me feel it’s might not work if I’m really really far away from the tower.
which mr6400 did you use because in another video someone had to open the router to expand the lte antena
What type of connector used for the antenna in the router?
Please reply, their is two antennae with cable connected but wifi router has only one port to connect one cable . So how did u connect please reply
I love your work!
Sir plz tell me will it work to bihar rural areas.? I'm getting almost 7-8 Mbps want almost 20-30 mbps for my work please help me I should buy or not ?
Thank You sir... Really a Helpful Video... Thanks Again!!
2 external LPDA antennas? Required? I'm aware the router has 2 small antenna. Only one external antenna or 2 antennas to be connected to router?
You would need to use two antenna for better signal quality.
I have. It WiFi line my home.i can use WiFi from satellite?
Hi is there any thing should I change it in the modem sitting
My plant locates inside the mountain. The distance to BTS was 4 Km. Is This 4G antenna possible? Thank
hahaha i love this guy the right guy. i am connecting 3dbi antenna to a bobcat hnt miner (crypto) my cable is 10meters(25ft) where do i place the booster and what type please?
you didn't show the indoor unit? What is the indoor Unit? How to connect ?
Will this antennas work with DLink dwr 920, which is 4G Router ?
Sir,is it good to mount only one antenna..or 2 antenna are mandatory
You need 2, if you use 1 than u will have 3G
Im using only 1 parabolic 18dbi antenna in my mr6400 and the other is the stock atenna. So far it’s working fine.
Planning to get the mr600 and i intend to use only the same parabolic antenna i have. Will that work?
I'm using Mr600 but we were 5kms far away from the tower, can i go for this or do i need to buy yagi antenna with 25dbi? please suggest.
thank you.
5km is far, I guess Yagi should work, but it may be costly to get two of those. What is signal strength that you get now and are you at the direct line of sight from the cell tower. If you are then you can try the lpda as well provided you get marginal signal strength now.
You can contact the above seller you should be able to get Yagi antenna at a good price.
@@diyIndia I'm not too sure about yagi antennas, they have good gain but narrow bandwidth. If you get two for two different frequencies you'll only be able to use inter-band aggregation (i.e. different bands) and not intra-band (same band) because each one will be polarised in one direction and won't pick up the other polarisation on that same frequency. You might be able to use just one frequency for both antennas, but then you can't use inter-band aggregation. LPDAs are more flexible because they're wide band and should allow both, but at the expense of lower gain. Also you'll never get 25dBi gain from a yagi! A better approach might be to use a flat dual polarised directional antenna like a Poynting Xpol2 and mount it in place of the feed horn of a satellite dish, there are youtube videos of people doing this and getting some very good gain. It's difficult to know which approach is best, it'll depend on your tower and what the aggregation capabilities of your router are as to what setup gives the highest and most reliable speeds.
@@markpurcell8075 Hey Mark how about parabolic / semi parabolic antenna with 2300-2500 MHz?
if you are using 2 antenna, do we need splitter
Any links to buy these !!?
bro where is link for the same as you told in the video from indiamart?
External entina buy link?
How did you connect dual antenna to the router? Did you any T connector. Because the router has 2 antenna, but 1 is for 4g and another for wifi. Curious to know
Both the antennas are for 4G.
Can you please confirm if there is any setting from the TP-link Interface we need to do while installing an external antenna with archer mr600?
Hey there. No there is no option that you need to turn on to enable external antenna.
Hi, can you install only 1 parabolic antenna in mr600 and the regular whip antenna at the other slot of the sma?
where can i buy this stuffs . am using mr600 and 4g sim . am here in saudi
if you insert an airtel sim and select lte band 40, it aggregates with two band 40s , y could easily achive speeds up to 100mbps, i get these speeds on my mobile if i stand this close to the base station
please do try airtel and jio in this one and update.......
Yes I do use airtel. Band 40 ca does not work in this beta firmware I believe. For me with Airtel only band 3, band 40 work on CA. if am only connected to band 40 in airtel with these antenna I easily reach 75mbps. But upload is only at 5 and 6 Mbps which is why am using vodafone. With CA 3,40. I get upload of 15 Mbps and download of 30mbps, but the router does not lock CA for long. I have to restart to lock it again, am waiting for stable firmware. The beta is buggy for now
@@diyIndia ok, btw where do you live?
Chennai.
In jio sim which bands should I use for getting aggregation ?
@@amaralingeswararaopola6526 in jio, if your device supports 3CA, all 3 bands can be aggregated, else b40+b40 can be used.
I bought an external yagi antenna from the internet. It works very well on an old router from huawei, but doesn’t work on newer models, like b310 or newer. Sometimes it doesn’t work at all, and orher times works interrupted, so that it screws up all the internet speed. Do you know why newer routers won’t work with my antenna?
Have you changed the settings on the dashboard?
I noticed that my router has three antenna options: auto, internal and external.
@@mturawa Yes, nothing has changed
Will this improve the signal if there is something like a big tall building in between the tower and ur antenna.. No direct line of sight..
you would need a direct line of sight, if there are building then the signals will be reflected by the walls. if you get good signals then you try the patch Antenna or Omni directional Antenna mounted little higher.
Dude your work is
awesome , I own a Mr 600 Router 4g+ works till noon and after that
Whatever I try band locking dosen't
work at all will this
work although my reception
is Excellent with 100 % coverage using a vi sim
If you already are getting 100% reception. It is not worth buying this.. do not spend this, it will work only if reception is low. For band lock use the beta firm ware. If you already have band lock and if router fails to hold it on, just restart it.
@@diyIndia i tried restarting it after choosing the bands even then it does not hold onto it , this is the v2 of the mr 600, replaced it once even then it dosent work . i found that the snr value is involved with the 4g+ and speeds , snr of 25 and above is giving me speeds of 70 to 80 mbps but as it drops to 13 to 15 speed goes down to 20mbps . whereas on my mobile with the same sim card getting 4g+ almost all the time and speeds always greater than 70mbps and early in the day 100+mpbs which is pretty insane . so will this help me improve the snr value or omni is better ? there are good number of towers in my area .
Can I use this in any other possible way without a router?(directly to the jiofi)
Becoz router cost more than this antennas..
No you can't used this on jiofi. Because that uses built in antennas
@@diyIndia Thanku bro
I always wondered...so can you confirm that when only one cable is drawn from the antenna, the latter should be connected to the port near the SIM slot?
yes you are correct. From the antenna, the wires gets connected to the router external antenna port which are generally SMA type.
Should i go for this?
Bcoz i facing internet fluctuations (wifi disconnection) problem in my one month old tp link tlmr6400...
Does this problem occur in this model too? Or this is just the network issue rather than device issues?
I have not faced any wifi disconnection issue. I have faced internet not connecting issue that was related to network, but no wifi disconnection. Did you try resetting flashing the firmware again?
I have a TL-ANT5819MS and I have the Base StationWBS510 for it. My problem is my router(TL MR6400) doesn't work with the antenna. What router do you have that can use a 4G sim card and work on the same frequency(5GHZ) as the antenna and base or Any advice or plan for them to work.
I m not sure I was able to understand that clearly, You need your router to work on 5 GHZ (Given out by the base station) and 4G data connecter to your router (which uses the ANT5819MS antennae ) ?
Which cat cable did u using ?
Hi,
1) I am using MR6400 though the router won't support CA it is necessary to buy 2LPDA antenna or one is enough?
2) 5m cable is suitable for two storeyed building rooftop to ground floor?
3) whatever the network in band 40 w/o CA the upload speed is very low like 2mbps by fixing this antenna will improve speed?
Hi, even though your router does not support CA I would suggest you to get two antennas this will help. 5meter would not be sufficient for the length which you mentioned. I would suggest you to run a length of cord or rope then measures to get accurate length. Even I have less upload speed in band 40, it's always been less than 2mbps but after fixing. It increase to 6 to 8 mbps, yes that's not great but I guess that's how much my base station supports in band 40 in my area.
Does it improve mobile signal also ?
The only visible repeater tower im connected too is 26 km away and getting 68-69 signal strength,
Is there a way to improve the signal from my antenna to repeater tower?
Ask home fiber or use parabolic antenna
It‘s already very good, i‘m like 3-4km away from the cell tower and my signal strength is about -80 to -110dBm on my mobile phone.
Maybe there‘s another cell tower you are connected to, you can find that out with Cellmapper.
Can u use local wifi internet cable in tp link mr 600, cat6, router instead of inserting sim ?
yes you can, you can use your local fiber connection and the 4g as the back up.
The red arrow on the antenna should point the tower.
I believe it indicates the top of antenna because there is a small drain hole opposite to the direction of the red arrow.
How did you connect 2 antenna to MR600? Isn't it has one gsm antenna and one wifi antenna. My understanding is that second gsm antenna is internal.
My understanding is that WIFI Antennas are internal and those external antennas are GSM ones.
Thank you for the video. Would you please share the details where you bought he LPDA and cables? I have already ordered Mr 600 and require the LPDA setup like yours.
I have uploaded the details in the description.
How much price you paid for mr600? I am always seeing 9449. But some claim they got it for 8000
Depends on the deal in amazon. I saw it was selling for rs8499 and on top of that you also get some banks discounts . If you want to wait for an Amazon sale then you might get at a cheaper price.
Cost may vary depending upon demand and supply.
How was the results of your setup?
Hello!
Please tell me as you have connected the external antennas, how the router gives Wifi.. is it that it has to be again connected to Wifi router through LAN!
Hi, The Antenna in the Mr600 is only for LTE and not for Wifi. The wifi antenna are built inside the router itself.
Nice! No legal questions to install such an antenna? I have the TL MR 100 and am also thinking about installing a 4G antenna.
Antenna is completely legal bro
Hi,Mr 600 two antinas are mobile signel caching?
Yes both are for mobile antenna and the wifi antenna is inside the router
Hi, I have a doubt what if I use one internal antenna and one external antenna, can I do carrier aggregation? Like say internal antenna on band3 and external antenna on band 40, will that work? Can anyone help me here?
are both antennas on mr600 4g or is one of them wifi ?
Good job. I have small opinion about removed antenna could you fix in outside via sma cable?
we could surely try that.
@@diyIndia may the both antenna for wifi or sim signal? Please find
Which kind of antenna is good for the area which is far away from tower and also forests nearby. I get low connectivity .Now with route r placed outside I usually get 600kbps to 3 mbps. Will omni directional , or directional antenna help(MIMO ,or not MIMO) ,patch or panel antenna help in this case
Lpda 12 dbi antenna best
Did you change any settings in the router to read the extenna antenna please?
No I did not . I just installed it and no settings changed.
@@diyIndia Thx
Hi , I stay away from tower around 2-3kms. There is no direct visibility at my home. If I move around 500m the tower is visible. Which type of Antenna do you recommend?
Lpda
can you show the firewall setting of this?
If you are looking anything specific , let me know there is lot of section in that firewall.
Hello. Can it work if i just bought one antenna only?
Yes, you need to connect to the stock antenna on the other one.
Is this for recharge?
Hey just purchased a to link mr600 , using it with an airtel sim . Which external antennas would you recommend . Also should I install one antenna or two ?
You should with two antenna. Only if the signal is low and if your have proper line of sight of the tower you can try lpda
MR6400 or MR600
I will use only ethernet cable so which one is best for me...
There is almost close to 4k difference between the prices, now you would need to decide if you are in spending extra 4k on LTE advance which is CA, now this is going to help you get better speed if the network provider supports it. The CA works on MR600 and MR600 has more supported band, but most band supported in INDIA are also supported in MR6400. It boils down to two things. Do you need CA and cost. If you can afford it get mr600
Sir I stay 3kms away from the nearest cell tower. One is jio and other one is Vodafone. Could you please suggest which type of antenna should I use ?
If you have the tower visibility lpda is good for mr600
@@diyIndia no sir...there are hills and trees in between...no direct visibility
Please make a video on 1 lpda and 2 lpda antenna speed test
I will try to include in my next video, What I have notice is that if I remove on antenna my speed will get reduced. This is what I had observed.
Hi sir, just wanna ask, currently I'm using modem TP-Link mr-6400, just done upgrade the firmware & have band for select, if use this signal booster can get higher speed? Thank you
Check speed test on open space terrace . Same mobile me jo speed milega vahi milega antenna lagane pr
I bought antenna couple of days back my stock antenna is providing better speed compared to lpda antenna,any suggestions??
How many antenna have you connected and in which router are you using it. Did you fix them at 45 degree angle.
@@diyIndia I have one antenna,I fixed it at 45 degree..
One does not work. And 45 degrees does not matter when you have only one. Try mounting it horizontal and see if it helps.
I am staying approximately 1-2 kms from the tower, in this case, should I use the antenna's that you are using or the Omni-directional antenna's? Please reply.
These antennas are cheap compared to omni- directional antenna. If the tower is in line of sight (That is, if you could point this antenna directly to it) you will get good results.
Can these antennas give good signal than yagi antenna
Please reply
no yagi has a better gain. close to 22db. So yagi will get you better signal for sure.
@@diyIndia Thak you sir
Suppose I have 1 Mbps as the maximum internet speed available around my area. By installing the antenna and tp link router, will I get a better internet speed?
For example: in your case, say you are getting 5Mbps inside your room, 10 Mbps on the terrace. Will you get more the 10Mbps in your room?
Internet speed depends on lot of factor. If you are already getting good quality signal and if your speed is only 1mbps then it is because of the network tower. Even if you get a tplink and antenna it won't help. Its for people who have less signal In there place. Check the comments to see if anyone has benefited based on your situation.
It will work for tplink mr200 ?
I am living in ground floor in a 3 floor building so if I keep the antennas in top floor , will I get wifi signal to ground floor or else I think my neighbours in 3rd floor will get better signal than me so what shall I do ?
What you could do is fix antenna on the terrace and run your cable to the ground floor and connect it with your router so that you can get wifi signal in ground floor. Antenna is used only for you 4g network.
Do you need to install a lightning surge protection ? does it work ok during heavy rain ?
I would Highly recommend that and it works well during heavy rain I had not faced any issues
The antennas should be grounded because electricity tries to find the easiest path to ground. Otherwise, the current would flow through the router and destroy something with a high possibility. And yes, it still should work during heavy rain, it‘s only a issue with mmWave and WiFi 2.4 GHz.
May i know did you connect both external antenna. then how did you broadcast wifi Signals Indore?
Both the antenna cable are connected to the MR 600 router and it will act like a normal WIFI hotspot.
If you connect both the antenna. And keep antenna above 30Feet. How does it broadcast inside house?
Hey there. The external antenna is only for 4G lte signals and not for wifi. I connected the antenna which are placed in the terrace and the MR600 has a built in Antenna for wifi inside the device and the device is placed inside my room. hope this clarifies.
@@diyIndia
that information is very hard to ascertain from the manual and all online details. I too thought the LTE antennas also did internal WiFi. Thanks for clarifying.
Bro u have to use lmr 400 or 600 because their will be no loss of signal
Hello bro, with internal antenna usage i see a download speed of 30mbps and upload speed less then 1mbps. Do i need to purchase two lpda outdoor antenna or one antenna will do. I am working from home, cannot take chances. Please suggest.
HI Niranjan, I am also doing work from home, If you know any good process, Please tell.
Hey guys, I have installed one external antenna and one stock antenna to the MR600 router. But results were bad when to compared to original stock antenna. I purchased OXYWAVE external 4G lte antenna but it's not doing great for me. Any suggestions pls.
Thankyou
I m not sure about radio technologies or whether single antenna might work for you, but what I could tell from searching the internet we need to have antenna setup as done in the video for better signal reception. Along with that the LPDA antenna must be in line of sight.
Make sure to plug external antenna connection to MAIN port and stock antenna in AUX port of router, but for optimum performance always use same type of antennas for correct MIMO configuration.
buy wher i want to buy it and how much
Contact details in the description
If there are trees between antenna and cell tower, how is the result ?
the results may vary, as these are directional antenna. if trees are there then the signa may drop.
Can wr use CPE610 as LPDA
Where to install the sim card?????
Antene lpda+booster repeater GSM+TP-LINK 6400.?
Is it legal to use it in India?
Can you provide purchasing link 🔗
Hi Sir
Ive got only one antenna.
I'm not getting much Speed.
Should I need to go for another one?
MR600 has two antenna, i would suggest to get another Antenna, I had tested with one antenna but it did not give much results.
Bro I want to know tp link archer mr600 supports sim slot or not some one saying sim slot was not supported I want to know please give reply bro
Hey. It does support sim. I have tried with all three network operators. Vodafone, jio and Airtel.
Hi. Will it work with TP-Link MR100 and 3g coverage?
Yes, to my knowledge you wouldn‘t even need 2 antennas. But also check, if your ISP will shut down 3G because in many countries it will be replaced (or is already replaced) by 4G and 5G. Also, 4G low band may be faster.
hi, how to set manually the modem on the extarnal antenna?
Hey, in mr600 there is no option to set as external antenna. You just plug and use.
@@diyIndia thanks
Hi bro this LMR 200 cable and television cable are same or different?
I m not an expert in electronics but those cables are totally different compared to LMR 200.
In my place signal tower is nearly 5-6kms dose it works
The signal quality will improve. Fiat check if the signal is coming in your mobile
How do i find tower
does it work for tp link mr 6400??? please reply asap
I am not sure about it ,but do check whether the antenna are removable or not. Some of the commenters in this video had mentioned about using MR6400.