You got the smarts my friend.. Did you see video of guy that built gears on . hope that wasn't you. But I thank you for the knowledge I needed to turn my inline fan into windmill. Now I got to go take apart again. Grateful I found you. Thanks.
Although you are correct that there would be losses converting to DC then back to AC via an inverter, the advantange would be that the output voltage and frequency would be regulated.
Hello and thank you for all your great videos! Besides getting AC current, what is the advantage of this reconfiguration vs using a 3 phase bridge (Diode) rectifier for dc current? Are there significant losses through a rectifier setup? Thx!
Excelente invento amigo ahora solo toca que construyas un generador eolico casero y ahorrar luz jejej ,claro colocando una caja de relación de velocidad al motor brushless para multiplicar el giro y listo...gracias por el video..
Realmente no creo que pueda encender una lámpara de 100 watts ya que la tensión podrá ser 110 o 230 voltios pero la corriente sería muy baja ya que el embobinado brushless na da para proporcionar la corriente requerida en la salida del transformador. Tal vez funcione para otras aplicaciones.
Where can I get the Controller which you have used here to run the brush less DC motor ? Please also give the specific name and specifications of the controller, if any.
These drivers are so fast, if your power supply current allows speed of the motor will pass speed of sound and the sticker on the motor can peal of with a loud boom scary sound in a fraction of a second .That little weight of label in those speed can not hold itself on the fast turning outrunning motor.
Though I was watching it much later, would like ask if I can attach this generator to my water turbine? And it's sure that at constant RPM enough current will be available to glow 10 LED bulbs. Isn't that right?
Hello Mr. Electron, I'm working on an off grid remote 120/240vac 60Hz AC generator system. Your knowledge of the 3 phase generator could be valuable to the project. The plan is to use a low RPM permanent magnet generator rated 10kw at 170 RPM, delivers 3 phase power, but I'm not sure if this is AC or DC or what Hz it would be producing. I plan on driving this with a Lister Diesel running at 650 to 670 rpm through a 4:1 reduction drive which should increase the torque of the engine and reduce the speed of the PMG to it's rated specifications. Questions are 1) can the output be directly from the generator assuming voltage and Hz are in range. 2) is it better to use a higher voltage and reduce it to 120/240vac with a step down transformer? I have 240v and 380v options for the PMG Or will I have DC power from this PMG and need to to create AC and Hz from DC and what device/s would be needed to accomplish the correct voltage and Hz? I'm trying to gather as much information as possible before spending $4000 on the engine and PMG for testing. Thanks for the great information in this video! 👍 Cheers, Darrin Goodman
Hello Congratulations on the video beautiful. Unfortunately I don't speak English. I'm just watching the image. I am writing with Google Translate. I'm sorry if I make a mistake. I have a question for you. I opened 1 servo motor with 9 coils. Sorry, I guess I couldn't do the linking process correctly. Sorry, I guess I couldn't do the linking process correctly. Sorry, I guess I couldn't do the linking process correctly. Sorry, I couldn't get the result I wanted. I can't comment so much because I can't understand our conversations in the video. I don't know where I made a mistake. Which Details should I pay attention to? I would be glad if you could help.
hallo, Im come from in Indonesia. that so simply? if i add a mosfet circuit to the transformer input, can the power output increase? thank you. (sorry my English is not good)
Why don't you put two loads in two separate AC lines L1 - L2 and L2 - L3. This way no power will be wasted and you don't have to remodel your Valuable BLDC motor by any means!
i believe that the only purpose of the video was to demonstrate how to turn a bldc into a single phase generator.. a few of those connected in series "if possible" and ran through a transformer powerful enough something like 6Kw could run a house... if you have appliances that runs only on 220v ac.. and obviously connected to a dc motor that run all generators with pulleys at once...
I thought the same in the begining but the thing with bldc motors is that the number of rotor poles (magnet poles are not the same as the number of stator or armature poles) for this very reason, the output volts weren't 3 times. Cool observation
the output voltage and it's 258 volts like the voltage in india and i'm know where you live it's india and i'm knew that because you wrote hindi word in the description of a video . don't worry i'm will didn't say this to any person . i'm didn't lie . if i said to a person . don't worry he will didn't go to you because the distance from my place i'm live in it is far .
*Join this channel to get access to perks:*
ruclips.net/channel/UCWFbPzBb7dCyCWuBA-DBrMAjoin
*Mr.Electron Patreon's Page* - www.patreon.com/mrelectron
*Hindi Channel* - www.youtube.com/@Mr.ElectronHindi
*Alternator Channel* - www.youtube.com/@mrelectron_alternator
*Watsapp Channel* - whatsapp.com/channel/0029VaQmmRaFCCoWOf7huh3G
You got the smarts my friend.. Did you see video of guy that built gears on . hope that wasn't you. But I thank you for the knowledge I needed to turn my inline fan into windmill. Now I got to go take apart again. Grateful I found you. Thanks.
Although you are correct that there would be losses converting to DC then back to AC via an inverter, the advantange would be that the output voltage and frequency would be regulated.
Nice work, it would be more helpful if you showed the pole testing and winding test as well
It goes three times the normal frequency.
So you are bypassing one leg of the Inverter driven Y connected stator, BLDC motor for single phase power generation? Smart Idea!
Hello and thank you for all your great videos! Besides getting AC current, what is the advantage of this reconfiguration vs using a 3 phase bridge (Diode) rectifier for dc current? Are there significant losses through a rectifier setup? Thx!
Всё просто и понятно, а главное что всё работает. Молодец, так держать.
Спасибо.
Excelente invento amigo ahora solo toca que construyas un generador eolico casero y ahorrar luz jejej ,claro colocando una caja de relación de velocidad al motor brushless para multiplicar el giro y listo...gracias por el video..
Quitale la cabeza del taladro.
Y contruya un GIROESCOPIO y se lo coloca y tiene una rotacion constante.
Brother from which photocopy machine you get this motor tell the name of it...
It's very useful. But i didn't get how u changed the connect . Explain with sticker on each wire . Please make another video. Please do it for me bro
Please give sketch drawing of winding connection with sequence for generator purpose.
Nicely explained and demonstrated... step by step .. Most excellentt . Bravo
Realmente no creo que pueda encender una lámpara de 100 watts ya que la tensión podrá ser 110 o 230 voltios pero la corriente sería muy baja ya que el embobinado brushless na da para proporcionar la corriente requerida en la salida del transformador. Tal vez funcione para otras aplicaciones.
Sangat bermanfaat untuk generator ac pada kebutuhan rumah tangga..
Did you do a series connection of the wires? and then the last end is the positive and negative terminals.
Thank you!
Where can I get the Controller which you have used here to run the brush less DC motor ? Please also give the specific name and specifications of the controller, if any.
These drivers are so fast, if your power supply current allows speed of the motor will pass speed of sound and the sticker on the motor can peal of with a loud boom scary sound in a fraction of a second .That little weight of label in those speed can not hold itself on the fast turning outrunning motor.
Though I was watching it much later, would like ask if I can attach this generator to my water turbine?
And it's sure that at constant RPM enough current will be available to glow 10 LED bulbs. Isn't that right?
Very nice video
Yah motor kis mein se nikalta hai
Would you be able to wire AC ammeter and voltage meter for monitoring and measuring voltage and current being produce by generator.
sure.
So good, I like it
Thanks
Thank`s
:)
Hola kisiera saver si conectas el motor al primario oal secundario del transformador
Hello Mr. Electron,
I'm working on an off grid remote 120/240vac 60Hz AC generator system. Your knowledge of the 3 phase generator could be valuable to the project.
The plan is to use a low RPM permanent magnet generator rated 10kw at 170 RPM, delivers 3 phase power, but I'm not sure if this is AC or DC or what Hz it would be producing.
I plan on driving this with a Lister Diesel running at 650 to 670 rpm through a 4:1 reduction drive which should increase the torque of the engine and reduce the speed of the PMG to it's rated specifications.
Questions are
1) can the output be directly from the generator assuming voltage and Hz are in range.
2) is it better to use a higher voltage and reduce it to 120/240vac with a step down transformer? I have 240v and 380v options for the PMG
Or will I have DC power from this PMG and need to to create AC and Hz from DC and what device/s would be needed to accomplish the correct voltage and Hz?
I'm trying to gather as much information as possible before spending $4000 on the engine and PMG for testing.
Thanks for the great information in this video! 👍
Cheers, Darrin Goodman
I have a bldc motor of four coils can you please make a video to show how to make generator by that. Thank you.
Hello
Congratulations on the video beautiful. Unfortunately I don't speak English. I'm just watching the image. I am writing with Google Translate. I'm sorry if I make a mistake. I have a question for you. I opened 1 servo motor with 9 coils. Sorry, I guess I couldn't do the linking process correctly. Sorry, I guess I couldn't do the linking process correctly. Sorry, I guess I couldn't do the linking process correctly. Sorry, I couldn't get the result I wanted. I can't comment so much because I can't understand our conversations in the video. I don't know where I made a mistake. Which Details should I pay attention to? I would be glad if you could help.
Did you just connect the three coils together in series to make it a single coil motor?
Yes.
Just making them in series won't give you full voltage you need to connect according to phases. Else you get less voltage.
@@MastercraftKARIGAR unfortunately the armature poles are not equivalent to rotor pole
Add a small RC kero/diesel motor to this and you have a good emergency charger for batteries (?)
hallo, Im come from in Indonesia.
that so simply?
if i add a mosfet circuit to the transformer input, can the power output increase?
thank you.
(sorry my English is not good)
Yes its that simple and i don't think adding mosfets can increase power. Also, your English is fine
Alright, thank you very much for your answer.
keep making useful work and keep spirit bro.
😃 sure
No.. generator power is already sinewave... No need ... So go easy
Power is fixed. It can't be increased but you can raise the efficiency by lowering any power loss through I×I×R.
Why don't you put two loads in two separate AC lines L1 - L2 and L2 - L3. This way no power will be wasted and you don't have to remodel your Valuable BLDC motor by any means!
i believe that the only purpose of the video was to demonstrate how to turn a bldc into a single phase generator..
a few of those connected in series "if possible" and ran through a transformer powerful
enough something like 6Kw could run a house...
if you have appliances that runs only on 220v ac..
and obviously connected to a dc motor that run all generators with pulleys at once...
Reason is increasing output voltage if the BLDC..
Please help me which wires to connect??. Tried to follow every step you said. Unable to generate after connection. Help me
Hello how to convert stepper motor into 3 phase motor please show wiring schema with star connection
Nice work
How to convert 3 phase altenator to single phase ?
just I had a motor received from old copier machine marked as 24 volt number of pins 10 how can I get electricity plz let me know tq
Wow! Can you share the connection scheme of the 3 phases?
Ok sure ! i will add it in my next video ending :)
Mr Electron thanks!
Did you converted from star to delta or just connect every winding in series.
in series
Is possible to do it on cdroom motor?
But you don't explain about star connection conversion
Modify table fan single phase squirrel cage induction motor into bldc motor
Ok
Very nice
Is it an RF voltage?
How much output watts coming out form the generator
Hola me gustaría saber de que artefacto sale el motor
Where can we buy this BLDC
Wait, which wires of the coils did you connect???
Wattage output ?
Aus welchem Drucker ist dieser Motor?
what is the stator diameter?
Sir please make esc 🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏
Height volts and low current
Helllo !!!!
Tumhare idea acha hai mare pass idea hai free electricity bna sakte hai
👍👍👍
hello
this generator produces ac, i need to add another intermediate device to charge the battery
You can convert to dc making a full bridge rectifier
You made a mistake while putting all coils in series. U wold get 3 times more voltage.
I thought the same in the begining but the thing with bldc motors is that the number of rotor poles (magnet poles are not the same as the number of stator or armature poles) for this very reason, the output volts weren't 3 times.
Cool observation
@@MrElectron it also alternates three times the frequency.
So using rectifier method is best or this connection method is best according to you
the output voltage and it's 258 volts like the voltage in india and i'm know where you live it's india and i'm knew that because you wrote hindi word in the description of a video . don't worry i'm will didn't say this to any person . i'm didn't lie . if i said to a person . don't worry he will didn't go to you because the distance from my place i'm live in it is far .
🌿
I can directly take voltage out of 1 phase 😁😁
HEY MAN CHANGE THE TITLE - THIS is NOT a DC motor the current is alternating in sinus form, so THIS is an AC (Alternating Current) Motor…
Fm where can i get it
Do you mean where can you get the motor?
@@Dipplers you r rt sir
@@somsherrai5170 ?
What is the wAtts
👍🏼👍🏼👍🏼👍🏼
Apke pass comment aara hi hai kya aara hi hai to reply karo
My school is so close to the transformer that we get 250 volts
Bahi Hindi me behi video bana kro
Mera hindi channel check kariye ye video Hindi me dekhne k liye..
Naam the professor dc motor
ami kinbo
Could you speak french please?
But language urdu...?
nice bro
pd your voice is sexy xD :D
completely junk, to use 2 ph. from a 3 ph. ac motyor/gen
200w, losses? genrated by youy hand?
including losses, you have 1/2 hp power in your hand? haha nice fake
It is not a new invention many people has done this before...
Its a copy...😡😡😡
Lol
Why ?
virusi cu prea multe reclame!
uh. no. fake....
Your demo on the winding wire connections is very confusing.
ты где такой хороший генератор взял мне такой тоже нужен