Я вот почти все понял, вот только не понял как двигатель 0.75квт может на выходе дать 10квт. Наверно все дело в наклейках, главное их надо правильно наклеить.
the oscillating EM wave is not controled by anything. It just amplifies until it reaches some limit. You may experiment catestrophic result, if current goes too high, causing the wires in transformers and in the stator to melt and take fire, and possibly explode as there's also no temperature/current limiter, except the natural resistance of coper wires of transformers and stator; also without any control of the oscillating EM, I bet it is not stable, and the frequency is most probably growing. That system could then emit undesired EM all around, interfering with radio waves and causing perturbations, because there's also no screening at all to absorb the EM waves radiated on both open sides of the stator. To suppress all these, an electronic device (using some power transistor and a small electric regulator) should stabilize the frequency and check that the "cos-phi" (angle between voltage and current) stays within the design limits of the stator (about 0.7 to 0.85 according to the plate). Otherwise that device may be dangerous. May be if the EM oscillates too fast, the 2 transformers may start to vibrate: they are not firmly maintained, just sticked with a basic rubber. If the transformers move, they will interact negatively with the oscillating wave, and the system may stop working, for no longer being in correct phase. In the video, there's no vibration, but the video is short. That engine should also never be left without a charge to dissipate the excess of energy. And you should not leave the small microwave motor (0.75W) plugged in for long, it will not resist if it has to absorb high currents. But I bet that the system cannot run for long, and the cos-phi will start varying (along with the frequency), and angular polarisations will have a negative effect on the inducted currents, causing the wave to turn off, and this is not easy to predict (depends on various noises, including temperature of the system) A basic security should be to install fuses in the wires connecting the two transformers to phases of the stator, so that it can also stop the system. And you can turn off the system by inserting an On/Off switch on those wires (the alternative is to remove the magnets on both sides, but if the system becomes unstable, these magnets will be pushed away by the oscillating EM wave having the incorrect polarity. In the video this works only because of a specific length of the bar and position of the two transformers: the osillating EM ways is propagated along the central bar, which is thick enough to support high currents without melting (but this cannot be said about the thin helicoidal wires in the 2 transforrmers and in the stator). The way the EM wave oscillates on the central bar (at specific wave lengths) is also dependant on the material with which it is built (it influences the speed of electrons), but also from the temperature and hygrometry of the air (where magnetic waves travel between the central bar and the stator). Try building it yourself, it may not work at all, unless there's a way to adjust the length of the bar or the horizontal position of transformers near both ends of the central bar. So alone, this system canot be stable. Either the builder in the video was very lucky, or he did not film here the many attempts made to adjust the system, and did not show the effective measurements he made to make it work in a stable way long enough to take short video captures (reassembeld later).
Thank you for the explanation. I set up similarly, but instead of the motor stator, I used a coil with thick wire. Result - 0. I don't know if it still makes sense. Your comments are very valuable. Thank you.
This as already been invented 100 years ago. The government has this technology but just decides to leave us in the dark about all the cool shit they have
Ohne rotierender Bauteile? Bei Slabodjan war das letzte mal dieses Funktionsprinzip gewesen bevor er verschwand...GENIAL wenn das so funktioniert. Schön wäre wenn ihr einer Art Anleitung anonym im Internet verbreiteten würdet. Es ist schon lange überfällig dass diese Technologie seinen Durchbruch erfährt in unseren Welt. Danke für eure Arbeit!
Спасибо Вам за просмотр и комментарий. Вы сэкономили моё время для просмотра фейка. Сейчас в инете так много фейков, по этому я сначала читаю комменты.
@@jumaniyazov51 пожалуйста! Все эти видео где из ничего получают kwt электроэнергии из ниоткуда не более чем фейк!! Если хотите бесплатное электричество то поставте солнечные панели
@@jumaniyazov51 No já jsem se zrychleně podíval. Pracoval jsem jako elektromechanik a takových motorů jsem převinul asi dvacet tisíc. Opravdu jsem se podivil, čemu dneska lidé mohou věřit. Sancta simplicitas.
Привяжи себе на горб этот пропеллер - вентилятор и дуй на Марс.. энергии тебе должно хватить..и болгарку с лампочкой не забудь взять с собой..марсиане заценят твою технологию..😂
Yes. (Copied from above) the oscillating EM wave is not controled by anything. It just amplifies until it reaches some limit. You may experiment catestrophic result, if current goes too high, causing the wires in transformers and in the stator to melt and take fire, and possibly explode as there's also no temperature/current limiter, except the natural resistance of coper wires of transformers and stator; also without any control of the oscillating EM, I bet it is not stable, and the frequency is most probably growing. That system could then emit undesired EM all around, interfering with radio waves and causing perturbations, because there's also no screening at all to absorb the EM waves radiated on both open sides of the stator. To suppress all these, an electronic device (using some power transistor and a small electric regulator) should stabilize the frequency and check that the "cos-phi" (angle between voltage and current) stays within the design limits of the stator (about 0.7 to 0.85 according to the plate). Otherwise that device may be dangerous. May be if the EM oscillates too fast, the 2 transformers may start to vibrate: they are not firmly maintained, just sticked with a basic rubber. If the transformers move, they will interact negatively with the oscillating wave, and the system may stop working, for no longer being in correct phase. In the video, there's no vibration, but the video is short. That engine should also never be left without a charge to dissipate the excess of energy. And you should not leave the small microwave motor (0.75W) plugged in for long, it will not resist if it has to absorb high currents. But I bet that the system cannot run for long, and the cos-phi will start varying (along with the frequency), and angular polarisations will have a negative effect on the inducted currents, causing the wave to turn off, and this is not easy to predict (depends on various noises, including temperature of the system) A basic security should be to install fuses in the wires connecting the two transformers to phases of the stator, so that it can also stop the system. And you can turn off the system by inserting an On/Off switch on those wires (the alternative is to remove the magnets on both sides, but if the system becomes unstable, these magnets will be pushed away by the oscillating EM wave having the incorrect polarity. In the video this works only because of a specific length of the bar and position of the two transformers: the osillating EM ways is propagated along the central bar, which is thick enough to support high currents without melting (but this cannot be said about the thin helicoidal wires in the 2 transforrmers and in the stator). The way the EM wave oscillates on the central bar (at specific wave lengths) is also dependant on the material with which it is built (it influences the speed of electrons), but also from the temperature and hygrometry of the air (where magnetic waves travel between the central bar and the stator). Try building it yourself, it may not work at all, unless there's a way to adjust the length of the bar or the horizontal position of transformers near both ends of the central bar. So alone, this system canot be stable. Either the builder in the video was very lucky, or he did not film here the many attempts made to adjust the system, and did not show the effective measurements he made to make it work in a stable way long enough to take short video captures (reassembeld later).
This is the most relevant question. Once it is "kickstarted" why doesn't the little kickstart motor (the thing that rotates the glass tray in microwave) keep going like all the other appliances plugged into same power board ??
Пока полной чистоты не будет, это лишь красивый фокус. Поднять всю установку в руки и включить мощную нагрузку и носить на руках на камеру со всех сторон. Until there is complete cleanliness, this is just a beautiful trick. Lift the entire installation in your hands and turn on a powerful load and carry it on your hands to the camera from all sides.
@@ГеннадийС-ъ7ы Мне больше нравится ДЕТЕКТИРОВАНИЕ МАГНИТНОГО ПОЛЯ а особенно ТЕОРИЯ БОЛЬШОГО ВЗРЫВА ИЗ НИЧЕГО подтверждающая РАБОТОСПОСОБНОСТЬ ВЕЧНОГО ДВИГАТЕЛЯ . А вам что нравится - швабра ?
Мне больше нравится ДЕТЕКТИРОВАНИЕ МАГНИТНОГО ПОЛЯ а особенно ТЕОРИЯ БОЛЬШОГО ВЗРЫВА ИЗ НИЧЕГО подтверждающая РАБОТОСПОСОБНОСТЬ ВЕЧНОГО ДВИГАТЕЛЯ . А вам что нравится - швабра ?
So as to what i have seen. There is no moving parts? Right? Can you tell us what is the theory? Since the magnetic force applied is "statically" in the coil? Meaning current won't be created in the coil unless there is an alternating magnetic polarity applied to it.
I'm tired of seeing comments from non science students and from those who claim to be science students but don't understand advanced physics, this system actually works i tried it, if you think y'all can afford to make one i promise to let you have it's complete composition, as long as you can afford the amount of silver and the rest, stop using your unresearched ideas to disrupt another man's invention, this should be applauded and not mocked, and this is confined within the law or physics, I'd prove it to you if you need explanation, it hasn't broken any law, this is not a perpetual motion engine it's just a high efficient engine, understand the difference and you're good to go
Я таким генератором обеспечиваю всю Прибалтику электроэнергией. Завтра после обеда еще один генератор подключу и начну электроэнергию в Казахстан экспортировать.
Is it based on a Don Smith design? Seems high pwr for 1 set of ring magnets & 1 core. What's freq out? The power tool needs 50/60 Hz. Did you calculate the coils' resonant freq B4 assembly?
А значит и не может быть переменного напряжения. Все источники электрической энергии работают на принципе генератора с вращающимся статором или ротором. Все остальные это преобразователи одной энергии в другую с большим количеством электронных компонентов. Здесь же нет ни чего, одни замкнутые контура, а это значит здесь обман и под столом стоит большая электро катушка подключенная к электросети играющая роль генератора. Как беспроводные зарядки телефонов.
Есть изобретатель если не ошибаюсь в европе который отсидел за свое изобретение на данный момент его сайт работает. Так вот в его тройном кольце и подведенными катушками вокруг для съема электричества там нет движущих частей или моментов, ничего не крутится. "Проект Заряд, Джон Серл"
@@АлексейЦыганков-м2е вот возьмите и повторите хотя бы то, что здесь показали, и поймёте, что это фейк, ложь, и обман. Признаюсь честно, этот якобы генератор, действительно работает. Но только не качестве генератора электричества, а как генератор бабла при просмотрах этого видео, вот так он работает точно и не поспоришь!!!
La cosa che mi sorprende è vedere come tanti babbei fanno i presuntuosi e fanno ironia convinti che ci sia il trucco quando è tutto chiaro del perchè il progetto funziona. L'unica cosa che mi stupisce è il fatto che non ci sono schermature alle oscillazioni EM e inoltre bisognerebbe capire se sono oscillazioni stabili. Comunque complimenti. Ho costruito anch'io un generatore con un alternatore, ma non con questo sistema. Io ho lasciato la parte mobile della dinamo e quindi fa un lieve rumore. Il tuo sistema è silenzioso al 1000% e anche se comprendo il sistema, ammetto che non ci sarei mai arrivato
I've stripped down an microwave oven and the there was only one very large power unit of the micro wave coils twas very heavy ad weighed as much as the rest of the microwave oven, Can you inform me of the make of the microwave oven the has two coil sets that are the typo you used in the Liberty Engine 2.
At 15:13 you attempt to demonstrate that, look no tricks, but then at 15:27 you change camera views, allowing you to easily have a wire now coming from underneath the table. One continuous unedited, uncut camera view is the only possible way of creating any type of credibility that you aren't trying to create an illusion. You have far too many cuts and changes in camera views to give you any credibility.
He's not trying to sell you anything. All he is trying to do, is show you what he and his cohorts came up with-just like the other liberty engines. I imagine he cares less whether you believe it o not. Doesnt change his life at all-or yours. If and when his group decides its safe to share and or sell the product(s), I'm sure they will find plenty of buyers whether you believe in it or not.
@@ccreddell True. Hope you're right and I'm wrong. Proof of concepts must be able to be verified by a third party. The problem is without verification, some unscrupulous individuals attempt to solicit people for investment money and end up scamming them for their hard earned savings.
@@feger481 You are not wrong. But so far, they havent asked for any money. I tend to go the Reagan route and trust but verify before I send anyone any money. I am getting all the pieces together to try and put one of these together though, so we'll see....
i can see resonance working here on the long bar inside the 50hz vibration on the bar question is which metal can vibrate on 50hz and produce over unity
In The proccess of fabrication of magnets ,to activate they use 300 v at 50 amps,,,so he just Made the oscillator starting with external energíy,,but the magnets keep the oscillations,👍
If you watch carefully, you can see that it's spinning. It even changes the direction. Please keep in mind, that it makes 4 rpm only. That's very slow…
l'energia non è statica l'energia deve essere sempre eccitata e creata da qualcuno o qualcosa. non è una batteria che accumula energia, in questo video ti fa credere che ha creato un generatore non un accumulatore
OK - działa , wymiary wałka z pamięci , zastosowałem mosiężny wałek , pozostałe wymiary organoleptycznie zrobiłem wzrokowo , patrząc na montaż każdego elementu generatora . Wracam z delegacji 2 grudnia i zrobię test na obciążenie i na czas ile wytrzyma w czasie 5 godzin . Pozdrawiam i niedowiarków pozdro !!!
Я поражаюсь всем этим видосам. Если умеешь и у тебя получается сделать изделие, то не для демонстрации, а для распространения сделай 2-3 экземпляра, для продажи. Кто купит и подтвердит эфективность, тогда в зачет. А так это видосики для пиар проекта фентези нью мен.
Согласен!!! Хотя бы видео правдивые выкладывали,а то такое впечатление что в школе либо не учили физику либо учебник скурили,либо только узнали этот фокус.😂
The first law of thermodynamics states that a perpetual motion machine of the first kind cannot exist, and the second law of thermodynamics states that one of the second kind cannot exist. Although those laws are more than a century old, patent applications for such devices are still filed every year. Very ingenious reasoning is often followed, but upon closer examination of these devices, the following two options always remain: either the device does not work, or there is a hidden energy source present.
Any new scientific invention has to go throught two processes -- peer review and independent replication, I understand during peer review this will be rejected, but if others are able to replicate it with your clear instructions, then this unit will reach masses. Can you make a detailed tutorial with diagrams for laymans?
I was sitting at the edge of my chair as this build was developing and it was all making sense to me, but I was perplexed as to how you were going to start an oscillation from a solid state generator. . . then you pulled out the synchronous motor and i about fell out of my chair, like watching the plot of a great movie unfold where there whole thing comes together. i know the connecting rod is the same material at the Liberty Engine 2 rotor. My question: can you shed any light on exactly what that alloy composition is? or a least a #### that represents that alloy? I have all the parts for my build but that. also, are the supporting brackets steel or aluminum? thanks!
Забавно, но это не работает так. Учите физику ребята😂. Но автор видео кое-где прокололся, а именно почему так называемый генератор пуска не стал вращаться самостоятельно после запуска всей конструкции. Хотя автор молодец большой он сделал генератор денег из воздуха) Вы просмотры и лайки а он денюшку с ролика.
Если посмотреть внимательно, то он начал вращаться, так же как в микроволновке, медленно. Пересмотрите, я сам вчера пересматривал и убедился что он начал вращаться.
What is that black insulation at 3:29? Mine don’t have that black insulation wire and I have the exact motor. Is that a modification you added? You can also see it at 3:16
@@thelibertyengineproject7966 you need to give us 1 prototype for see it really works or not.... or you give only shame from community... i do beta test and after i see it work i promise to give you back, we can signed a contract
Ottimo progetto penso di farlo anchio, il motore trifase da 05cv cel'ho , un trafornatore del microonde anche (debbo trovarne un'altro) e adesso ordino i magneti e il synchro...Ma il mio dubbio resta: quanto dura questa erogazione di corrente? dato che lo connetterei ad una stufetta elettrica da 1000vatt e la farei andare in continuo durante tutto l'inverno...
In realtà è un campo elettromagnetico che si auto-alimenta... quindi il processo è costante finché i magneti non perdono il loro magnetismo. Ma dal mio punto di vista bisogna mettere dei fusibili... la barra o totalmente di argento o rame
16,45 minuta czemu przez moment miernik pokazał zero. Podejrzewam przełączenie prądu na zasilanie ukryte. Nie ma cudów, już od kilku lat przeprowadzam próby z róznymi ciekawostkami.
Hello, the video shows that you connect a grinder, a flashlight and a fan, and why didn't you use at least one magnet to prove your video, thereby interrupting the flow of electricity, then it would become clear that it really works.
Could you kindly explain, if the power of the motor windings is 0.75KW, then how can you get 10x power out of this tuning??? And how did you maybe measure it???
In reality, it is a flux flip flop inductor that is shorted out magnetically, opposing itself so the oscillations created by the microwave oven dish motor is enough to trigger a reaction, pulsing the initial source of energy back and forth simultaneously that it keeps oscillating with greater efficiency than any Meissner circuit because it works with a dead magnetic short so to speak, instead of an electrical short, flux concentrations and electricity ring and cancel each other out but it gives enormous amounts of oscillating maf=gnetic energy that is converted back to electricity at 10 or more times from the coils. It could only start up via it's trigger using an oscillation at the proper voltage. Since the coils are tuned to 50 hz, the same frequency sets off and triggers a 50Hz cycle at the same voltage, bouncing it back and forth to infinity no matter what you try to draw from it, I'm guessing gauge of the coils of wire and gauge of wire used basically is the limit via the amperage of the wire and coils. Does this heat up or is it something that stays fairly cool until really loaded? I could actually see how it works in my head, you feed the start up energy into the two outside phase connections and the motor is backfed across two points of the delta in which the stator is wound and connected to the input terminals, then the stator windings reverberate the signal through all three coils, bouncing back and forth until it rings continuously at 50Hz across the coil you broadcasted to. The signal from the little motor is good to start it up, but does it jump to 50 or 60 hz or does this fluctuate a lot?. This is absolute genius. Have you experimented with cancelling the magnetic field using NSNS outward facing in motor armatures driving a dc signal by electromagnet into one winding with universal motors before? I think I understand how you did the last liberty engines like I am saying, no?
Можете объяснить что у вас с магнитным полем происходит в стержне. Оно пульсирует? Для чего вы его поджимаете магнитами с двух сторон. Катушки от СВЧ трансформатора с разным направлением намотаны? Снимается полезный сигнал с обмоток статора двигателя?
I wonder if the material, diameter and weight of the core have any significance? did the transformer from the microwave windings leave primary or secondary? любопытно имеет ли какое то значение материал, диаметр и вес сердечника? а трансформатор от микроволновки - обмотки оставил первичные или вторичные?
More than likely it does. Just like with the liberty engine, they will never give you the one secret that makes this work because of patents / trade secrets. These guys are going to hold on to this secret until they can sell or license it to you for profit. The only benefit humanity gets out of these videos is proof that free energy exists and that we will never get our hands on it. The reason these guys keep their identity secret is because they know someone one would find them and beat the secrets out of them to share with humanity and they would not get wealthy from this.
Hola, el anterior con el motor y alternador me convencia mas, este se ve aun mas sencillo y trabaja igual segun vi, pero los cortes de dicho video me dan a entender que se esconde algo.
Amigo repetir um progeto mecânico que usava imã e 2 bobinas com iman num veio cilindrico meso usando um motor esterno para o girar ele produzia 0 de enegia e foi copiado so ínfimo detalhe não dar para crer em tudo que montra nós videos só testando para saber vai que funciona algum deles se estiver próximo de um rio ou possua um poço com muita agua dar para oroduzir um gerador capaz de gerar uma boa energia
So nice of you not to patent this technical marvel and make a fortune while solving the energy problems of the world. I'm so touched, my tears are also 100% real. OMG LMAO.
Ty tak serio? 🤣 Przecież już podstawy fizyki wyniesione z zawodówki Ci powiedzą że takie coś nie ma prawa działać, łykacie ludzie wszystko jak pelikany 😅
Bonjour monsieur je viens de voir votre vidéo pour ce moteur de 10 kW comment puis-je me le procurer et à quel prix je suis en France merci pour la démonstration
Absolutely. Take your extension cord from the wall outlet, wrap it twice around the table holding any motor you like and plug your devices directly into it.
Can you make a follow-up video where you plug the light in as well as the fan and pich the Power Generator up with the camera placed so one can see there are no cables under the Power Generator? There are too many videos on FB showing "Free Power" that do not work. If this works you should be able to demonstrate that quite easy
Excellent objection... If people believe this, then no wonder there are so many people who believe the earth is a flat plate... This world works by natural laws, not by magic tricks... (easy fun for the ignorant).. .
@@petarkostic3768exactly. "Free energy"... They don't know the 1st law of thermodynamics. They think it is possible to create energy from nothing or to have zero loss, zero friction, and so on 🤦🤦
it's all about getting clicks and earning money from the videos. They know there are a lot of curious people out there, and unfortunately most of them are also gullible.
The first law of thermodynamics states that a perpetual motion machine of the first kind cannot exist, and the second law of thermodynamics states that one of the second kind cannot exist. Although those laws are more than a century old, patent applications for such devices are still filed every year. Very ingenious reasoning is often followed, but upon closer examination of these devices, the following two options always remain: either the device does not work, or there is a hidden energy source present.
the oscillating EM wave is not controled by anything. It just amplifies until it reaches some limit. You may experiment catestrophic result, if current goes too high, causing the wires in transformers and in the stator to melt and take fire, and possibly explode as there's also no temperature/current limiter, except the natural resistance of coper wires of transformers and stator; also without any control of the oscillating EM, I bet it is not stable, and the frequency is most probably growing. That system could then emit undesired EM all around, interfering with radio waves and causing perturbations, because there's also no screening at all to absorb the EM waves radiated on both open sides of the stator. To suppress all these, an electronic device (using some power transistor and a small electric regulator) should stabilize the frequency and check that the "cos-phi" (angle between voltage and current) stays within the design limits of the stator (about 0.7 to 0.85 according to the plate). Otherwise that device may be dangerous. May be if the EM oscillates too fast, the 2 transformers may start to vibrate: they are not firmly maintained, just sticked with a basic rubber. If the transformers move, they will interact negatively with the oscillating wave, and the system may stop working, for no longer being in correct phase. In the video, there's no vibration, but the video is short. That engine should also never be left without a charge to dissipate the excess of energy. And you should not leave the small microwave motor (0.75W) plugged in for long, it will not resist if it has to absorb high currents. But I bet that the system cannot run for long, and the cos-phi will start varying (along with the frequency), and angular polarisations will have a negative effect on the inducted currents, causing the wave to turn off, and this is not easy to predict (depends on various noises, including temperature of the system) A basic security should be to install fuses in the wires connecting the two transformers to phases of the stator, so that it can also stop the system. And you can turn off the system by inserting an On/Off switch on those wires (the alternative is to remove the magnets on both sides, but if the system becomes unstable, these magnets will be pushed away by the oscillating EM wave having the incorrect polarity. In the video this works only because of a specific length of the bar and position of the two transformers: the osillating EM ways is propagated along the central bar, which is thick enough to support high currents without melting (but this cannot be said about the thin helicoidal wires in the 2 transforrmers and in the stator). The way the EM wave oscillates on the central bar (at specific wave lengths) is also dependant on the material with which it is built (it influences the speed of electrons), but also from the temperature and hygrometry of the air (where magnetic waves travel between the central bar and the stator). Try building it yourself, it may not work at all, unless there's a way to adjust the length of the bar or the horizontal position of transformers near both ends of the central bar. So alone, this system canot be stable. Either the builder in the video was very lucky, or he did not film here the many attempts made to adjust the system, and did not show the effective measurements he made to make it work in a stable way long enough to take short video captures (reassembeld later).
Если он только покажет свое лицо То его обязательно за это убьют Через некоторое время (((((( И ещё объявят шарлатаном Вот он и оберегает свою жизнь и правильно делает !!!! Дольше проживет !!!!! А это самое главное жить долго !!!!
Nope he wouldn't be living with everything he ever dreamed off. Nevet to be famous, he wouldn't be rich, he only would be death! Assassination by Oil petro-dollar Mafia! So for yr own Safety can you please stop this free energy bullcrap.. I'm sick of it!
Самое интерестное ,это ручная динамомашинка которая типа возбуждает всю схему как волшебная палочка,тоесть мгниты с обмотками и начинается генерирование откуда-то свч аж 230в.и,работает даже пятидесятигерцовая болгарка,Тесла отдыхает!!!!
In The proccess of fabrication of magnets ,to activate they use 300 v at 50 amps,,,so he just Made the oscillator starting with external energíy,,but the magnets keep the oscillations,👍
Здравствуйте Либерти я смотрю все ваши изобретения вы гении своего дела хотелось бы узнать только один ответ что это правда. Я понимаю что секрет остаться за вами и есле это так то вы могли бы помоч миллионам людей сказав правду что это реальность а не фокус
Τα 10kw είναι αλήθεια και πραγματικό, αλλά θα χρειαστεί να δειται το βιντεάκι πολλές φορές ώστε να προσέξετε δύο και μόνο πράγματα για να προχωρήσετε στην κατασκευή αυτή, πολλά συγχαρητήρια σε αυτή την ομάδα των ανθρώπων ΜΠΡΑΒΟ ΣΑΣ. 10:26
ПомочЬ ... к стати ... И это лишь фокус для просмотров ... Спроси у этого "мастера" - как удалось достичь 230 и при частоте переменки - в 50 герц . Он не даст ответ. Однозначно.
Зачем на тачку ? На космолёт и за пределы галактики ! Электроников в провода запустил, а они там бегают и размножаются да ещё с такой скоростью, что исчерпать невозможно никакой нагрузкой.
Я вот почти все понял, вот только не понял как двигатель 0.75квт может на выходе дать 10квт. Наверно все дело в наклейках, главное их надо правильно наклеить.
🤣
Странно, когда моторчик завели (генератор), напряжение появилось, но потом моторчик не стал работать (двигатель) и его отключили. 🤗
даже не удивительно что ты ни....... не понял :))
the oscillating EM wave is not controled by anything. It just amplifies until it reaches some limit. You may experiment catestrophic result, if current goes too high, causing the wires in transformers and in the stator to melt and take fire, and possibly explode as there's also no temperature/current limiter, except the natural resistance of coper wires of transformers and stator; also without any control of the oscillating EM, I bet it is not stable, and the frequency is most probably growing. That system could then emit undesired EM all around, interfering with radio waves and causing perturbations, because there's also no screening at all to absorb the EM waves radiated on both open sides of the stator.
To suppress all these, an electronic device (using some power transistor and a small electric regulator) should stabilize the frequency and check that the "cos-phi" (angle between voltage and current) stays within the design limits of the stator (about 0.7 to 0.85 according to the plate). Otherwise that device may be dangerous.
May be if the EM oscillates too fast, the 2 transformers may start to vibrate: they are not firmly maintained, just sticked with a basic rubber. If the transformers move, they will interact negatively with the oscillating wave, and the system may stop working, for no longer being in correct phase. In the video, there's no vibration, but the video is short. That engine should also never be left without a charge to dissipate the excess of energy. And you should not leave the small microwave motor (0.75W) plugged in for long, it will not resist if it has to absorb high currents.
But I bet that the system cannot run for long, and the cos-phi will start varying (along with the frequency), and angular polarisations will have a negative effect on the inducted currents, causing the wave to turn off, and this is not easy to predict (depends on various noises, including temperature of the system)
A basic security should be to install fuses in the wires connecting the two transformers to phases of the stator, so that it can also stop the system. And you can turn off the system by inserting an On/Off switch on those wires (the alternative is to remove the magnets on both sides, but if the system becomes unstable, these magnets will be pushed away by the oscillating EM wave having the incorrect polarity. In the video this works only because of a specific length of the bar and position of the two transformers: the osillating EM ways is propagated along the central bar, which is thick enough to support high currents without melting (but this cannot be said about the thin helicoidal wires in the 2 transforrmers and in the stator).
The way the EM wave oscillates on the central bar (at specific wave lengths) is also dependant on the material with which it is built (it influences the speed of electrons), but also from the temperature and hygrometry of the air (where magnetic waves travel between the central bar and the stator). Try building it yourself, it may not work at all, unless there's a way to adjust the length of the bar or the horizontal position of transformers near both ends of the central bar.
So alone, this system canot be stable. Either the builder in the video was very lucky, or he did not film here the many attempts made to adjust the system, and did not show the effective measurements he made to make it work in a stable way long enough to take short video captures (reassembeld later).
Thank you for the explanation. I set up similarly, but instead of the motor stator, I used a coil with thick wire. Result - 0. I don't know if it still makes sense. Your comments are very valuable. Thank you.
have you tried to build this yet? i built the easy one with pvc and 2 circle magnets, dont work. have most of parts together now for this one.
i suggest you collaborate and perfect this machine to make a world a better place and share it, so we can have this so called free energy, good luck
This as already been invented 100 years ago. The government has this technology but just decides to leave us in the dark about all the cool shit they have
Bara de argalium? Interesant! Din păcate nu învățăm așa ceva la școală. Secretul rămâne pentru generațiile care vin. 😊
Ohne rotierender Bauteile? Bei Slabodjan war das letzte mal dieses Funktionsprinzip gewesen bevor er verschwand...GENIAL wenn das so funktioniert. Schön wäre wenn ihr einer Art Anleitung anonym im Internet verbreiteten würdet. Es ist schon lange überfällig dass diese Technologie seinen Durchbruch erfährt in unseren Welt. Danke für eure Arbeit!
Самое сложное в этой конструкции, это спрятать питающий сетевой провод, с чем автор справился отлично!!!
Спасибо Вам за просмотр и комментарий. Вы сэкономили моё время для просмотра фейка. Сейчас в инете так много фейков, по этому я сначала читаю комменты.
@@jumaniyazov51 пожалуйста! Все эти видео где из ничего получают kwt электроэнергии из ниоткуда не более чем фейк!! Если хотите бесплатное электричество то поставте солнечные панели
мне в этих видео всегда больше интересна как они наёбывают а не наебалово это или нет
@@jumaniyazov51 No já jsem se zrychleně podíval. Pracoval jsem jako elektromechanik a takových motorů jsem převinul asi dvacet tisíc. Opravdu jsem se podivil, čemu dneska lidé mohou věřit. Sancta simplicitas.
Привяжи себе на горб этот пропеллер - вентилятор и дуй на Марс.. энергии тебе должно хватить..и болгарку с лампочкой не забудь взять с собой..марсиане заценят твою технологию..😂
Pregunta : porque cuando le da impulso con el motor de microondas, el mismo no sigue girando, puesto que ya tiene energía?
Kręci się, 3 obroty na minutę - jesteś ślepy czy jesteś ignorantem... ?
😂😂😂😂😂
Hello, does the bar in the center need a specific measurement (size, diameter)? Is this the motor shaft? THANKS
Yes. (Copied from above)
the oscillating EM wave is not controled by anything. It just amplifies until it reaches some limit. You may experiment catestrophic result, if current goes too high, causing the wires in transformers and in the stator to melt and take fire, and possibly explode as there's also no temperature/current limiter, except the natural resistance of coper wires of transformers and stator; also without any control of the oscillating EM, I bet it is not stable, and the frequency is most probably growing. That system could then emit undesired EM all around, interfering with radio waves and causing perturbations, because there's also no screening at all to absorb the EM waves radiated on both open sides of the stator.
To suppress all these, an electronic device (using some power transistor and a small electric regulator) should stabilize the frequency and check that the "cos-phi" (angle between voltage and current) stays within the design limits of the stator (about 0.7 to 0.85 according to the plate). Otherwise that device may be dangerous.
May be if the EM oscillates too fast, the 2 transformers may start to vibrate: they are not firmly maintained, just sticked with a basic rubber. If the transformers move, they will interact negatively with the oscillating wave, and the system may stop working, for no longer being in correct phase. In the video, there's no vibration, but the video is short. That engine should also never be left without a charge to dissipate the excess of energy. And you should not leave the small microwave motor (0.75W) plugged in for long, it will not resist if it has to absorb high currents.
But I bet that the system cannot run for long, and the cos-phi will start varying (along with the frequency), and angular polarisations will have a negative effect on the inducted currents, causing the wave to turn off, and this is not easy to predict (depends on various noises, including temperature of the system)
A basic security should be to install fuses in the wires connecting the two transformers to phases of the stator, so that it can also stop the system. And you can turn off the system by inserting an On/Off switch on those wires (the alternative is to remove the magnets on both sides, but if the system becomes unstable, these magnets will be pushed away by the oscillating EM wave having the incorrect polarity. In the video this works only because of a specific length of the bar and position of the two transformers: the osillating EM ways is propagated along the central bar, which is thick enough to support high currents without melting (but this cannot be said about the thin helicoidal wires in the 2 transforrmers and in the stator).
The way the EM wave oscillates on the central bar (at specific wave lengths) is also dependant on the material with which it is built (it influences the speed of electrons), but also from the temperature and hygrometry of the air (where magnetic waves travel between the central bar and the stator). Try building it yourself, it may not work at all, unless there's a way to adjust the length of the bar or the horizontal position of transformers near both ends of the central bar.
So alone, this system canot be stable. Either the builder in the video was very lucky, or he did not film here the many attempts made to adjust the system, and did not show the effective measurements he made to make it work in a stable way long enough to take short video captures (reassembeld later).
How is that possible without rotation to producing ac?In what laws of physics is working on?Thanks.
Kaç Amp, güç, üretiyor?
pra que baterria no carro eletrico
Once you energize it with the synchronous motor , you switch it off with the switch, but does it kill the circuit or is it still giving 230v ?
@wesleykuo8731 try to replicate ... but do it faithfully with respect to the video
To which terminals do we connect the socket for the starting impulse?
At the voltage input or the voltage output?
you will never get one reply from scamer
Když nemáte motorek z mikrovlnky, tak použijte liščí ocas a ebonitovou tyč.
What’s the cost of 1 unit?
Since you're out of the socket, why doesn't the small motor you make the first move start? Shouldn't it work on it?
This is the most relevant question. Once it is "kickstarted" why doesn't the little kickstart motor (the thing that rotates the glass tray in microwave) keep going like all the other appliances plugged into same power board ??
Én úgy láttam, hogy lassan de tovább forgott amíg ki nem húzta
Пока полной чистоты не будет, это лишь красивый фокус. Поднять всю установку в руки и включить мощную нагрузку и носить на руках на камеру со всех сторон.
Until there is complete cleanliness, this is just a beautiful trick. Lift the entire installation in your hands and turn on a powerful load and carry it on your hands to the camera from all sides.
I want to see it working out side on a concrete floor then watch him remove the magnets.
Witam też pracuje nad tym to jest na tą chwilę nie realne. Pozdrawiam.
exactly also when you plug 120volt grinder into 220 it would have bad things happen
❤
@@czesawzaeski1364 zbudowałem dokładną kopie -- ale niestety nie generuje nic -- moze rdzen jest inny niz stalowy
Когда смотрю такие видео то чисто для поржать, уверен что очень много электриков очень громко тоже ржут. 😀
Раньше лапшу цепляли а теперь магниты
@@vadimrind2460.И что больше нравится из двух ??? . Лапша или магниты ??? .
@@ГеннадийС-ъ7ы
Мне больше нравится ДЕТЕКТИРОВАНИЕ МАГНИТНОГО ПОЛЯ а особенно ТЕОРИЯ БОЛЬШОГО ВЗРЫВА ИЗ НИЧЕГО подтверждающая РАБОТОСПОСОБНОСТЬ ВЕЧНОГО ДВИГАТЕЛЯ . А вам что нравится - швабра ?
Мне больше нравится ДЕТЕКТИРОВАНИЕ МАГНИТНОГО ПОЛЯ а особенно ТЕОРИЯ БОЛЬШОГО ВЗРЫВА ИЗ НИЧЕГО подтверждающая РАБОТОСПОСОБНОСТЬ ВЕЧНОГО ДВИГАТЕЛЯ . А вам что нравится - швабра ?
Это лопша но не каша
İlginç, spiral makinesi çalıştığında lambada voltaj düşümü olmuyor. Nükleer tesisten alıyor olmalı şebeke elektriğini?
evet abi yoktan var etti 😂😂😂😂
So as to what i have seen. There is no moving parts? Right? Can you tell us what is the theory? Since the magnetic force applied is "statically" in the coil? Meaning current won't be created in the coil unless there is an alternating magnetic polarity applied to it.
Good evening, I would like to know what type of material this central shaft is made of
its made of unobtainium...
Ya so the material can not be obtained
😂@@bunnykiller
ФЕЙК КРАСИВО ИЗГОТОВЛЕН ! ШИКАРНАЯ МАСТЕРСКАЯ !
I'm tired of seeing comments from non science students and from those who claim to be science students but don't understand advanced physics, this system actually works i tried it, if you think y'all can afford to make one i promise to let you have it's complete composition, as long as you can afford the amount of silver and the rest, stop using your unresearched ideas to disrupt another man's invention, this should be applauded and not mocked, and this is confined within the law or physics, I'd prove it to you if you need explanation, it hasn't broken any law, this is not a perpetual motion engine it's just a high efficient engine, understand the difference and you're good to go
Я таким генератором обеспечиваю всю Прибалтику электроэнергией. Завтра после обеда еще один генератор подключу и начну электроэнергию в Казахстан экспортировать.
Saludos una pregunta de q material se compone el eje q va en el centro del motor
Alloy aluminum brother
@@juvenalgonzalez8756
hello sir, how to stop the generator? from producing the current
Remove the circle magnets
This project should be tested in middle school laboratories to stimulate young people's brains.
Как будто побывал в цирке на выступлении хорошего фокусника😅, Вопрос : откуда взялась частота 50Hz?
Ну , так... откуда 10 кил , оттуда ж и 50 герцов)) "не будем им мешать" ))
Оттуда же откуда 10кВт))) из розетки на стене помещения)))
Вот и я задался этим же И почему не происходит срыва частоты? Тоже не понятно, чем она стабилизирована?
Nice. What is the shaft in the middle made of? What is the material?
Also the measurements..
the shaft is precisely machined from a secret alloy of precious metals which form a room temperature superconductor, producing overunity in the system
i just made that up btw
@@mrp3066 is iron oxide and metal
The shaft is the original shaft that came with the motor
Молодец, дай бог что бы тебе дети на старости лет так же воды дали, как ты всем открытие сотворил....
По простому-Это то же самое,что жить, постоянно питаясь своим говном..Великий Дэвид Копперфильд "рыдает"...
Is it based on a Don Smith design? Seems high pwr for 1 set of ring magnets & 1 core. What's freq out? The power tool needs 50/60 Hz. Did you calculate the coils' resonant freq B4 assembly?
He tested it on a device that works on frequency need of 50/60 HZ , yes ?
How long the magnet resist?
what is the cylinder in the middle? Is it a specific alloy?
Да это конкретный сплав, называется ЛОХОТРОН!
That's absolutely genius. The thing that's even more genius is that there are no moving parts.
А значит и не может быть переменного напряжения. Все источники электрической энергии работают на принципе генератора с вращающимся статором или ротором. Все остальные это преобразователи одной энергии в другую с большим количеством электронных компонентов. Здесь же нет ни чего, одни замкнутые контура, а это значит здесь обман и под столом стоит большая электро катушка подключенная к электросети играющая роль генератора. Как беспроводные зарядки телефонов.
@@Зубогрыз ага и через железный стол наводит индуктивную энергию 😁😁😁
Есть изобретатель если не ошибаюсь в европе который отсидел за свое изобретение на данный момент его сайт работает. Так вот в его тройном кольце и подведенными катушками вокруг для съема электричества там нет движущих частей или моментов, ничего не крутится. "Проект Заряд, Джон Серл"
@@АлексейЦыганков-м2е вот возьмите и повторите хотя бы то, что здесь показали, и поймёте, что это фейк, ложь, и обман. Признаюсь честно, этот якобы генератор, действительно работает. Но только не качестве генератора электричества, а как генератор бабла при просмотрах этого видео, вот так он работает точно и не поспоришь!!!
Я бы поверил , наверно , если бы он поднял платформу с генератором во время работы нагрузки , а так осталась большая вероятность фэйка.
100% фейк😂
La cosa che mi sorprende è vedere come tanti babbei fanno i presuntuosi e fanno ironia convinti che ci sia il trucco quando è tutto chiaro del perchè il progetto funziona. L'unica cosa che mi stupisce è il fatto che non ci sono schermature alle oscillazioni EM e inoltre bisognerebbe capire se sono oscillazioni stabili. Comunque complimenti. Ho costruito anch'io un generatore con un alternatore, ma non con questo sistema. Io ho lasciato la parte mobile della dinamo e quindi fa un lieve rumore. Il tuo sistema è silenzioso al 1000% e anche se comprendo il sistema, ammetto che non ci sarei mai arrivato
Ráno prášek zelený, v poledne růžový a večer oranžový, 3 krát denně svěrací kazajka.
Does it rotate?? Or it makes electricity without any part movement ??
Olá amigo qual dispositivo que vc alimenta para partir o gerador
Um motor de microondas
I've stripped down an microwave oven and the there was only one very large power unit of the micro wave coils twas very heavy ad weighed as much as the rest of the microwave oven, Can you inform me of the make of the microwave oven the has two coil sets that are the typo you used in the Liberty Engine 2.
All microwaves have only one transformer. You must use four similar transformers.
Kad si pobudio uređaj zasto se motoric za pobudu nije nastavio okretati ako je pokrenuo struju
At 15:13 you attempt to demonstrate that, look no tricks, but then at 15:27 you change camera views, allowing you to easily have a wire now coming from underneath the table. One continuous unedited, uncut camera view is the only possible way of creating any type of credibility that you aren't trying to create an illusion. You have far too many cuts and changes in camera views to give you any credibility.
He's not trying to sell you anything. All he is trying to do, is show you what he and his cohorts came up with-just like the other liberty engines. I imagine he cares less whether you believe it o not. Doesnt change his life at all-or yours. If and when his group decides its safe to share and or sell the product(s), I'm sure they will find plenty of buyers whether you believe in it or not.
@@ccreddell True. Hope you're right and I'm wrong. Proof of concepts must be able to be verified by a third party. The problem is without verification, some unscrupulous individuals attempt to solicit people for investment money and end up scamming them for their hard earned savings.
@@feger481 You are not wrong. But so far, they havent asked for any money. I tend to go the Reagan route and trust but verify before I send anyone any money. I am getting all the pieces together to try and put one of these together though, so we'll see....
They are making money from views likes subscriptions and ads from youtube.
just do it, and see for your self
Microwave turntable motors are all 12 volts, but the one shown here is 220 volts.
Bonjour la barre au centre faut il une mesure (taille, diamètre) spécifique? S’agit il de l’axe du moteur? Merci
What is your reason for hiding electricity?
i can see resonance working here on the long bar inside the 50hz vibration on the bar question is which metal can vibrate on 50hz and produce over unity
In The proccess of fabrication of magnets ,to activate they use 300 v at 50 amps,,,so he just Made the oscillator starting with external energíy,,but the magnets keep the oscillations,👍
@@MrAcapela how do we fabricate the magnet
Can you show me the wiring diagram?
여러분 전기와 자기에서 N과 S가 연속적으로 바뀌지 않으면 절대로 연속적으로 전기가 발생한다고 믿습니까? 혹시 원자력이라고 생각합니까? 속이는자와 속는자의 차이는?
3 phase is full time induction, each leg @ 60 hz, cycles. How to start the induction field and maintain it ?
It is very troubling that his power meter reads 666 each time he turns it on. Just saying.
the more simple is to hack the meter..
May I ask if the strip metal is aluminum alloy or stainless steel?
The small motor you first energize should spin when energy production starts, but it never spins.
If you watch carefully, you can see that it's spinning. It even changes the direction. Please keep in mind, that it makes 4 rpm only. That's very slow…
❤
l'energia non è statica l'energia deve essere sempre eccitata e creata da qualcuno o qualcosa. non è una batteria che accumula energia, in questo video ti fa credere che ha creato un generatore non un accumulatore
OK - działa , wymiary wałka z pamięci , zastosowałem mosiężny wałek , pozostałe wymiary organoleptycznie zrobiłem wzrokowo , patrząc na montaż każdego elementu generatora . Wracam z delegacji 2 grudnia i zrobię test na obciążenie i na czas ile wytrzyma w czasie 5 godzin . Pozdrawiam i niedowiarków pozdro !!!
Я поражаюсь всем этим видосам. Если умеешь и у тебя получается сделать изделие, то не для демонстрации, а для распространения сделай 2-3 экземпляра, для продажи. Кто купит и подтвердит эфективность, тогда в зачет. А так это видосики для пиар проекта фентези нью мен.
Согласен!!! Хотя бы видео правдивые выкладывали,а то такое впечатление что в школе либо не учили физику либо учебник скурили,либо только узнали этот фокус.😂
what material is the shaft made of? is it taken from the engine without modification?
No please it is made specially for the purpose of transferring electrons from one end to the other end to enable the generation of electricity
So do research about galvanic corrosion
The shaft material is ArGalium Alpha. We have told many clues about this material in our videos
Сможешь сделать это или продать заранее спасибо
What are the properties of the shaft between the transformers?
Hi.
What is the ratio of silver : aluminum in electro magnet field bar? How much should it weight ?
Thank you.
Из какого материала изготовлен вал ?
@@СергейЧеремош Смешно ! Хотелось бы уточнить: это какая то Электросталь или обычная СТ3 ?
вал металлический, должен магнититься.
Please give us all the details to make one, you would be a hero
Did you receive the info you requested?
I've the details information
@@freeelectricgenerator7921 please send them to me
원리가 이해 안가네요
no that is not the way
Dove posso trovare la barra centrale di argalium per provare a replicare il progetto? Posso usare anche altri materiali?
L'unica alternativa è una barra di Rame
Please give us a link to the wiring diagram. Thanks.
The first law of thermodynamics states that a perpetual motion machine of the first kind cannot exist, and the second law of thermodynamics states that one of the second kind cannot exist. Although those laws are more than a century old, patent applications for such devices are still filed every year. Very ingenious reasoning is often followed, but upon closer examination of these devices, the following two options always remain: either the device does not work, or there is a hidden energy source present.
@@joteirlinck4778there are 2 things infinite, the universe and the stupidity of mens, but for the first im not really sure. A. Einstein
А еще был случай когда Мюнхаузен вытянул себя за волосы из болота...
Красивый удлинитель только зачем на нём столько лишних деталей хватило бы и фанерки с розеткой
...скорей всего литиевые аккумы в доске - основании
@@максимкиселёв-ш1ии я про это думаю, две доски аккумулятор внутри, доски с изолентой обмотаны, понтом красиво.
هل هذا حقيقة ام خدعه 😂
он творец, он так видит
@@максимкиселёв-ш1и ! Совершенно верно! В таких делах без прибомбассов не обходится!
Mi spieghi come fa a generare 10 KW se i dati di targa dicono 220/380 volt massimo 3 Ampere???
E' la solita fregnaccia
Hi can I use a single phase motor or not
You can use both single-phase and three-phase motors. It won't work with either.
Any new scientific invention has to go throught two processes -- peer review and independent replication, I understand during peer review this will be rejected, but if others are able to replicate it with your clear instructions, then this unit will reach masses.
Can you make a detailed tutorial with diagrams for laymans?
He won’t be long for this world if he starts helping others successfully build them.
I was sitting at the edge of my chair as this build was developing and it was all making sense to me, but I was perplexed as to how you were going to start an oscillation from a solid state generator. . . then you pulled out the synchronous motor and i about fell out of my chair, like watching the plot of a great movie unfold where there whole thing comes together. i know the connecting rod is the same material at the Liberty Engine 2 rotor. My question: can you shed any light on exactly what that alloy composition is? or a least a #### that represents that alloy? I have all the parts for my build but that. also, are the supporting brackets steel or aluminum? thanks!
The supports are made of steel. Today we have published another video in which we tell some information about the metal of the core
LO HE HECHO CON UN TUBO DE ALUMINIO Y NO FUNCIONA ...PUEDES DAR ALGUN DETALLE DE QUE MATERIAL USAR O DONDE SE CONSIGE ESE QUE USASTE 😢
Y EN LA CONEXIÓN CONECTAS LOS DOS CABLES MARRONES JUNTOS Y LOS AZULES EN EL OTRO LADO DEJANDO LA FASE DEL MEDIO SIN CONEXIÓN 😮???
@@FoxEcoit'll never be explained because it doesn't work. Great videos and thought provoking ideas though.
8:03
Where can I get the parts to make.
Это не работает.
How long does this energy remain at the same value?
여러분 전기와 자기에서 N과 S가 연속적으로 바뀌지 않으면 절대로 연속적으로 전기가 발생한다고 믿습니까? 혹시 원자력이라고 생각합니까? 속이는자와 속는자의 차이는?
Забавно, но это не работает так. Учите физику ребята😂. Но автор видео кое-где прокололся, а именно почему так называемый генератор пуска не стал вращаться самостоятельно после запуска всей конструкции. Хотя автор молодец большой он сделал генератор денег из воздуха) Вы просмотры и лайки а он денюшку с ролика.
Стол разделен на два потенциала и очень хорошо замаскирован. На 20:48 видна еле заметная полоска разделения стола. В ножках контакты. Старый фокус.
👏👍
Если посмотреть внимательно, то он начал вращаться, так же как в микроволновке, медленно. Пересмотрите, я сам вчера пересматривал и убедился что он начал вращаться.
Та физика о тпаразитов, даваемая в школе есть научный бред для оболванивая наших детей. НАУКА - для идиотов. Раньше была Тривия.
What is that black insulation at 3:29? Mine don’t have that black insulation wire and I have the exact motor. Is that a modification you added? You can also see it at 3:16
Don't know. It is a piece of rubber or rubber
@@thelibertyengineproject7966 you need to give us 1 prototype for see it really works or not.... or you give only shame from community... i do beta test and after i see it work i promise to give you back, we can signed a contract
У меня есть чёрная лента, но лучше синяя - КПД выше.
@@Energolog
Are you did the generator? Is it working?
Ottimo progetto penso di farlo anchio, il motore trifase da 05cv cel'ho , un trafornatore del microonde anche (debbo trovarne un'altro) e adesso ordino i magneti e il synchro...Ma il mio dubbio resta: quanto dura questa erogazione di corrente? dato che lo connetterei ad una stufetta elettrica da 1000vatt e la farei andare in continuo durante tutto l'inverno...
In realtà è un campo elettromagnetico che si auto-alimenta... quindi il processo è costante finché i magneti non perdono il loro magnetismo. Ma dal mio punto di vista bisogna mettere dei fusibili... la barra o totalmente di argento o rame
Jaka cena za ten generator ? CIEKAWA KONSTRUJCJA
16,45 minuta czemu przez moment miernik pokazał zero. Podejrzewam przełączenie prądu na zasilanie ukryte. Nie ma cudów, już od kilku lat przeprowadzam próby z róznymi ciekawostkami.
@@krzysztofbuczek7238 To zrób próbę z generatorem Figuera.
TWOŻĄ TAKIE ŚCIEMY ŻEBYŚ UZNAŁ ŻE NIC SIĘ NIE DA ALE TESLA POSZEDŁ DALEJ WIĘC UMARŁ JAK LEPPER
@@janusz1268 w płaską ziemie też wierzysz? 🤣
😂😂😂 хороший фейк, молодец👍🏻 а частоту 50 герц откуда берёшь умник, преобразователь как минимум на мосте нужно построить. Красиво спрятал.
pourquoi le moteur synchrone ne s'est pas mis a tourner puisqu'il y avait 230V dans la prise ?
Hello, tell me what metal is made of the metal cylinder that passes through the stator of the remaining part of the engine?
Hello, the video shows that you connect a grinder, a flashlight and a fan, and why didn't you use at least one magnet to prove your video, thereby interrupting the flow of electricity, then it would become clear that it really works.
Hello sir your generator produced 230v ok good but why synchronous motor not running
SYNCHOMOTOR WAS NOT RUNNING, COS WAS NOT PLUGED IN. BUT, AS YOU CAN SEE, IT DOESN'T NEED TO BE ON, AS THE THING HAS MICROWAVE PARTS. 🤣
I'd like to know if you made the shaft out of alum/silver or is it just iron thanks for showing this
Dont botther. Brother.. this. Not. Real .. their. Is no voltage drop .. avr too
that sharft is batery hahahaha.this is not real this is joke.
quale e' il pricipio di fuzionamento?carica dei condensatori e poi?
Could you kindly explain, if the power of the motor windings is 0.75KW, then how can you get 10x power out of this tuning??? And how did you maybe measure it???
In reality, it is a flux flip flop inductor that is shorted out magnetically, opposing itself so the oscillations created by the microwave oven dish motor is enough to trigger a reaction, pulsing the initial source of energy back and forth simultaneously that it keeps oscillating with greater efficiency than any Meissner circuit because it works with a dead magnetic short so to speak, instead of an electrical short, flux concentrations and electricity ring and cancel each other out but it gives enormous amounts of oscillating maf=gnetic energy that is converted back to electricity at 10 or more times from the coils. It could only start up via it's trigger using an oscillation at the proper voltage. Since the coils are tuned to 50 hz, the same frequency sets off and triggers a 50Hz cycle at the same voltage, bouncing it back and forth to infinity no matter what you try to draw from it, I'm guessing gauge of the coils of wire and gauge of wire used basically is the limit via the amperage of the wire and coils. Does this heat up or is it something that stays fairly cool until really loaded? I could actually see how it works in my head, you feed the start up energy into the two outside phase connections and the motor is backfed across two points of the delta in which the stator is wound and connected to the input terminals, then the stator windings reverberate the signal through all three coils, bouncing back and forth until it rings continuously at 50Hz across the coil you broadcasted to. The signal from the little motor is good to start it up, but does it jump to 50 or 60 hz or does this fluctuate a lot?. This is absolute genius. Have you experimented with cancelling the magnetic field using NSNS outward facing in motor armatures driving a dc signal by electromagnet into one winding with universal motors before? I think I understand how you did the last liberty engines like I am saying, no?
Hello, Thank you for great your explanation! Are you aware of any other devices utilizing this process or additional information on it? Thank you!
The real question is how many amps it can handle?
0
Можете объяснить что у вас с магнитным полем происходит в стержне. Оно пульсирует? Для чего вы его поджимаете магнитами с двух сторон. Катушки от СВЧ трансформатора с разным направлением намотаны? Снимается полезный сигнал с обмоток статора двигателя?
De cuanto son los condensadores
I wonder
if the material, diameter and weight of the core have any significance?
did the transformer from the microwave windings leave primary or secondary?
любопытно
имеет ли какое то значение материал, диаметр и вес сердечника?
а трансформатор от микроволновки - обмотки оставил первичные или вторичные?
More than likely it does. Just like with the liberty engine, they will never give you the one secret that makes this work because of patents / trade secrets. These guys are going to hold on to this secret until they can sell or license it to you for profit. The only benefit humanity gets out of these videos is proof that free energy exists and that we will never get our hands on it. The reason these guys keep their identity secret is because they know someone one would find them and beat the secrets out of them to share with humanity and they would not get wealthy from this.
Masa iya
Hola, yo me imagino que el devanado primario. Porque el secundario tiene un voltaje muy alto, como de 1000v más o menos.!🎉
How long is the metal bar?
I just found out that the bar is 8in long.
In the last video we tell that information
What is the center induction motor that is magnet or metal
There is a lot of content like this on RUclips. After some research, I saw that there is an induction coil under this installation.
여러분 전기와 자기에서 N과 S가 연속적으로 바뀌지 않으면 절대로 연속적으로 전기가 발생한다고 믿습니까? 혹시 원자력이라고 생각합니까? 속이는자와 속는자의 차이는?
No2
Bạn nói rất dúng hoặc họ dùng một cái bếp từ De ở dưới trò trẻ Con
Bạn phải nói rằng ke lừa dối mà học thức kém lại nghĩ mình là thiên tài tetla
Nie ma cewki indukcyjnej ...tylko prad wzbudzajacy
Please reveal the specifications for the production
That'll make the viewers happy
Try!
its eazy :D dont waste time with this and use wall plug :D :D here is too normal AC plug under :D :D
Please do another video Lifting the Unit while its powering a device to prove No Incoming-AC Line connected.
Serait il possible d’avoir la liste des pièces pour réaliser le projets
Hola, el anterior con el motor y alternador me convencia mas, este se ve aun mas sencillo y trabaja igual segun vi, pero los cortes de dicho video me dan a entender que se esconde algo.
Amigo repetir um progeto mecânico que usava imã e 2 bobinas com iman num veio cilindrico meso usando um motor esterno para o girar ele produzia 0 de enegia e foi copiado so ínfimo detalhe não dar para crer em tudo que montra nós videos só testando para saber vai que funciona algum deles se estiver próximo de um rio ou possua um poço com muita agua dar para oroduzir um gerador capaz de gerar uma boa energia
opino lo mismo.
So nice of you not to patent this technical marvel and make a fortune while solving the energy problems of the world.
I'm so touched, my tears are also 100% real. OMG LMAO.
😂🤣😂
Czy można go kupić lub zamówić ?
Ty tak serio? 🤣 Przecież już podstawy fizyki wyniesione z zawodówki Ci powiedzą że takie coś nie ma prawa działać, łykacie ludzie wszystko jak pelikany 😅
Bonjour monsieur je viens de voir votre vidéo pour ce moteur de 10 kW comment puis-je me le procurer et à quel prix je suis en France merci pour la démonstration
Thanks for your video. Can I use a 4HP 3-phase motor instead of the 0.75KW 3-phase motor in your video?
Absolutely. Take your extension cord from the wall outlet, wrap it twice around the table holding any motor you like and plug your devices directly into it.
Can you make a follow-up video where you plug the light in as well as the fan and pich the Power Generator up with the camera placed so one can see there are no cables under the Power Generator?
There are too many videos on FB showing "Free Power" that do not work.
If this works you should be able to demonstrate that quite easy
Excellent objection... If people believe this, then no wonder there are so many people who believe the earth is a flat plate... This world works by natural laws, not by magic tricks... (easy fun for the ignorant).. .
@@petarkostic3768exactly. "Free energy"... They don't know the 1st law of thermodynamics. They think it is possible to create energy from nothing or to have zero loss, zero friction, and so on 🤦🤦
it's all about getting clicks and earning money from the videos. They know there are a lot of curious people out there, and unfortunately most of them are also gullible.
If it works really he would win the Nobel prize 😂
And would win much more money with his own company than with RUclips rewards 😂
The first law of thermodynamics states that a perpetual motion machine of the first kind cannot exist, and the second law of thermodynamics states that one of the second kind cannot exist. Although those laws are more than a century old, patent applications for such devices are still filed every year. Very ingenious reasoning is often followed, but upon closer examination of these devices, the following two options always remain: either the device does not work, or there is a hidden energy source present.
the oscillating EM wave is not controled by anything. It just amplifies until it reaches some limit. You may experiment catestrophic result, if current goes too high, causing the wires in transformers and in the stator to melt and take fire, and possibly explode as there's also no temperature/current limiter, except the natural resistance of coper wires of transformers and stator; also without any control of the oscillating EM, I bet it is not stable, and the frequency is most probably growing. That system could then emit undesired EM all around, interfering with radio waves and causing perturbations, because there's also no screening at all to absorb the EM waves radiated on both open sides of the stator.
To suppress all these, an electronic device (using some power transistor and a small electric regulator) should stabilize the frequency and check that the "cos-phi" (angle between voltage and current) stays within the design limits of the stator (about 0.7 to 0.85 according to the plate). Otherwise that device may be dangerous.
May be if the EM oscillates too fast, the 2 transformers may start to vibrate: they are not firmly maintained, just sticked with a basic rubber. If the transformers move, they will interact negatively with the oscillating wave, and the system may stop working, for no longer being in correct phase. In the video, there's no vibration, but the video is short. That engine should also never be left without a charge to dissipate the excess of energy. And you should not leave the small microwave motor (0.75W) plugged in for long, it will not resist if it has to absorb high currents.
But I bet that the system cannot run for long, and the cos-phi will start varying (along with the frequency), and angular polarisations will have a negative effect on the inducted currents, causing the wave to turn off, and this is not easy to predict (depends on various noises, including temperature of the system)
A basic security should be to install fuses in the wires connecting the two transformers to phases of the stator, so that it can also stop the system. And you can turn off the system by inserting an On/Off switch on those wires (the alternative is to remove the magnets on both sides, but if the system becomes unstable, these magnets will be pushed away by the oscillating EM wave having the incorrect polarity. In the video this works only because of a specific length of the bar and position of the two transformers: the osillating EM ways is propagated along the central bar, which is thick enough to support high currents without melting (but this cannot be said about the thin helicoidal wires in the 2 transforrmers and in the stator).
The way the EM wave oscillates on the central bar (at specific wave lengths) is also dependant on the material with which it is built (it influences the speed of electrons), but also from the temperature and hygrometry of the air (where magnetic waves travel between the central bar and the stator). Try building it yourself, it may not work at all, unless there's a way to adjust the length of the bar or the horizontal position of transformers near both ends of the central bar.
So alone, this system canot be stable. Either the builder in the video was very lucky, or he did not film here the many attempts made to adjust the system, and did not show the effective measurements he made to make it work in a stable way long enough to take short video captures (reassembeld later).
Если он только покажет свое лицо
То его обязательно за это убьют
Через некоторое время ((((((
И ещё объявят шарлатаном
Вот он и оберегает свою жизнь и правильно делает !!!!
Дольше проживет !!!!!
А это самое главное жить долго !!!!
Nope he wouldn't be living with everything he ever dreamed off. Nevet to be famous, he wouldn't be rich, he only would be death! Assassination by Oil petro-dollar Mafia! So for yr own Safety can you please stop this free energy bullcrap.. I'm sick of it!
Agradeço a vossa cooperação, partilha e ensinamento. Muito obrigado e muitas felicidades. Continuem e libertem o engenho da energia livre.
Почему столько телодвижений? Можно было просто взять провод и к его концам подсоединить нагрузку - ура, есть бесплатная энергия!!!
шудра, а ты проверь сам
Самое интерестное ,это ручная динамомашинка которая типа возбуждает всю схему как волшебная палочка,тоесть мгниты с обмотками и начинается генерирование откуда-то свч аж 230в.и,работает даже пятидесятигерцовая болгарка,Тесла отдыхает!!!!
Are you an Eskimo? I have magic ice box I need to sell you 🛶
Видно как он при подьеме всей площадки стараеться поставить ее в определенное место и ножки закрывает руками.
In The proccess of fabrication of magnets ,to activate they use 300 v at 50 amps,,,so he just Made the oscillator starting with external energíy,,but the magnets keep the oscillations,👍
какое свч ,ты бредишь
@@АндрейКуликов-л5м это не мои слова ,сказанное было в ролике
Здравствуйте Либерти я смотрю все ваши изобретения вы гении своего дела хотелось бы узнать только один ответ что это правда. Я понимаю что секрет остаться за вами и есле это так то вы могли бы помоч миллионам людей сказав правду что это реальность а не фокус
Why tell trick when he gets clicks =$$$?
Єто лохотрон для просмотров видео.
Τα 10kw είναι αλήθεια και πραγματικό, αλλά θα χρειαστεί να δειται το βιντεάκι πολλές φορές ώστε να προσέξετε δύο και μόνο πράγματα για να προχωρήσετε στην κατασκευή αυτή, πολλά συγχαρητήρια σε αυτή την ομάδα των ανθρώπων ΜΠΡΑΒΟ ΣΑΣ. 10:26
@@МояПасека нет не лохотрон. дело в магнитах и волнах.
ПомочЬ ... к стати ... И это лишь фокус для просмотров ... Спроси у этого "мастера" - как удалось достичь 230 и при частоте переменки - в 50 герц . Он не даст ответ. Однозначно.
Where we can get the silver metal , can you provide me some diagrams
We have manufactured this metal ourselves. Not for sale yet
Этот генератор нужно установить на грузовую тачку и по перону грузы возить!Красиво навещал лапшу на уши ,за ролик 👏.
Зачем на тачку ? На космолёт и за пределы галактики ! Электроников в провода запустил, а они там бегают и размножаются да ещё с такой скоростью, что исчерпать невозможно никакой нагрузкой.