Might have been better when aligning the 3 disks to use DTI on tack weld then position them before final weld! I do love these videos watching how someone gets over a problem with ingenuity.
I too wish to build a pellet machine and small hammer mill .. but I dont have a lathe and am not confident enough in my fabrication skill to build a machine that slings blades at 1700 rpm 😆 maybe one day. I do enjoy watching yours, though. Thanks so much for sharing!
A lathe is very useful for a household. I have never built a grinding mill either. I wanted to try and I see that I succeeded. Thank you for your support.
@@DorelBorlea multumesc mult, accesibil, Slava Domnului. ma uit pentru o optiune si eu sa le schimb la o moara care are ... multicele :)Spor in toate ! O Zi buna! Doamne ajuta
@@DorelBorlea merci , asha fac shi eu dar se mananca diuzele prea repede. Am cumparat un pistol cu masa incorporarata dar nu am apucat sal probez. Salutari din Spania
@@igotbricotools2035 la materiale pana in 6mm grosime duzele merg foarte bine. Am taiat aproximativ 3 metri de tabla.de 6 mm cu o singura duza si inaca mai merge.
I have one almost same, but with square blades. I switch side of blades because side that hits become rounded. So, side that hits is square again but I can see that parts of wood that comes out are a bit bigger than before. At start it was like in your video at 1st seconds of video. What can be a reason for that?
Супер , молодец!! Я изготовил дробилку такого же плана,-молотковую дробит зерновые,сено,початки кукурузы,на вал установил вентилятор и дробленная масса уходит в мешок через цыклон. Заходите в гости имею дробилки разных конструкций, экструдеры,веялка зерновых,пресс для брикетов, чертежи..и другие поделки..
Might have been better when aligning the 3 disks to use DTI on tack weld then position them before final weld! I do love these videos watching how someone gets over a problem with ingenuity.
I too wish to build a pellet machine and small hammer mill .. but I dont have a lathe and am not confident enough in my fabrication skill to build a machine that slings blades at 1700 rpm 😆 maybe one day. I do enjoy watching yours, though. Thanks so much for sharing!
A lathe is very useful for a household. I have never built a grinding mill either. I wanted to try and I see that I succeeded. Thank you for your support.
Nc project, can i ask what is the size of those nuts? and also the thickness of the plates?
Thanks. The plates are 6mm thick, the nuts are 16mm but I drilled them with a 19mm drill.
Doamne ajuta Dorel.
de unde ai luat ciocanelele rodura, cat au costat?
Multumesc mult si spor in tot ce faci!
De pe utb shop. Nu mai stiu cat au costat. Un jur de 100 lei toate cutitele.
@@DorelBorlea multumesc mult, accesibil, Slava Domnului. ma uit pentru o optiune si eu sa le schimb la o moara care are ... multicele :)Spor in toate ! O Zi buna! Doamne ajuta
@@popescuadrian4170 Multumesc. Cutitele acestea sunt destul de rezistente , ieftine si se schimba repede.
@@DorelBorlea multumesc, :) Slava Domnului Dn. Dorel! Doamne Ajuta.
Good work?
But Mill for which material ?
straw, grass, alfalfa
7:44 What is the name of the item? Where can I buy it?
these are knives or blades for tractor-drawn rotary mowers
Is it possible to make a hammer mill from an old dust blower fan? Must the "hammers" be movable or can i weld them directly to the fan blades?
I think you can build a straw grinding mill out of a dust fan. The hammer mill is built with movable knives.
@@DorelBorlea I want to grind wood chips into smaller particles like sawdust so i can use it in my pellet press
I ground wood chips with this hammer mill. It's going super well.
@@DorelBorlea Can you grind wood chips with a mill with fixed knifes?
@@theodorranebo2909 I don't know.
Hello sir, can it cut coconut husk?
Hello. I don't know.
Sir could u please suggest this type hammer mill grind the waste printed circuit boards in to powder
Bun vídeo 👍
0:37 cand tai cu plasma la ce distantza tzii diuza de placa?
O tin lipita de material
@@DorelBorlea merci , asha fac shi eu dar se mananca diuzele prea repede. Am cumparat un pistol cu masa incorporarata dar nu am apucat sal probez.
Salutari din Spania
@@igotbricotools2035 la materiale pana in 6mm grosime duzele merg foarte bine. Am taiat aproximativ 3 metri de tabla.de 6 mm cu o singura duza si inaca mai merge.
I want the mill, my wife wants the dog!
I have one almost same, but with square blades. I switch side of blades because side that hits become rounded. So, side that hits is square again but I can see that parts of wood that comes out are a bit bigger than before. At start it was like in your video at 1st seconds of video. What can be a reason for that?
The type of wood and the humidity of the sawdust. The mill should grind the same, only the sawdust is different.
Mai montezi inca doua axuri cu cutite s-au ramane in doua?
4 axuri cu cutite am vrut sa montez dar merge bine si cu doua.
what size are those blades sir?
96mm × 40mm x 3mm
thank you very much! how about the plates and steel rods?@@DorelBorlea
@@denjaspersilorio7621 plates are 230mm , steel roads are 19 mm.
Супер , молодец!!
Я изготовил дробилку такого же плана,-молотковую дробит зерновые,сено,початки кукурузы,на вал установил вентилятор и дробленная масса уходит в мешок через цыклон.
Заходите в гости имею дробилки разных конструкций, экструдеры,веялка зерновых,пресс для брикетов, чертежи..и другие поделки..
How much does it cost
Is not for sale.
Moter HP?
5kw
@@DorelBorlea production per hour
@@Tafseerraza-f9g I don't know
Nice video
Good work
Thanks!
I wonder why you not cut the hair around the Dog eyes?
Berapa harga satu unit pak
Puedes partir ...rocas no superior a ...1..c.m..2c.m...3c.m gracias
Ok bien
❤🎉❤🎉