Thanks for this video. I bought evo fortin chrt 4 for my Dodge Charger 2010. This video was really helpful. Did exactly like this. Now I’ve a remote start in my car😊
I got one for a 2016, ordered it off ebay but the instructions are way too confusing. It is the evo one with only the t-harness. I am attempting to install tomorrow but I also didn't get a install instructions manual just the one available online. Any info on how to wire this one to work like how you did with this one?
Its a 2016 dodge journey with a push button start. I was attempting to bench set up the wire harness like you did but I only have the one yellow wire off the top harness. It says I have to wire the can-hi and can-low but has 2 wires for each (2 for hi, 2 for low) one set is orange and the other set is grey. I figured I would wire the power that goes to the ignition straight from the push button harness and avoid any problems with hooking up the wrong wire off the main harness. Any help would be greatly appreciated! I would have ordered yours if it would have shown up in the ebay listing but it only showed up when I searched for it by your company name sadly.
Hi ... I really need help 😫... I bought I bought the Excalibur RS-275-3DB BECAUSE IT SAYS WAS A PLUG AND PLAY BUT THIS THING HAS TOOO MANY CABLES.. CAN YOU PLEASE TELL ME WHAT TO DO ...I NEED HELP.
I Installed a Fortin EVO - All in a 2008 Jeep Liberty 4WD For a year it worked perfectly Now when I use the remote to start and then shut down or turn off the Jeep The next time I either use the remote or Key to start the starter over engages for about three seconds If I shut the car off with either the remote or key it doesn’t over engage the starter But if I use the remote again to start the car the whole process starts again I have done a master reset and reprogrammed a total of three times But the problem persists Any help would be greatly appreciated. I don’t want to destroy my starter
Hello my name is Chuck. I have a 2002 Chrysler Town and Country.I would like to know what it cost me for one of those setups I'll plug and play like you just
Still waiting to find out how much it will cost me for you to hook one of these up so I can plug and play in a 2002 Chrysler Town and country and what it would cost
I have bought one for my 2005 vrand Cheroke, tried to install it but when i reached programming the evo device will keep on flashinh all the lights even with the button is pressed Could you plz help
Mine didn't come with the hood pin and a few other things you mentioned. Not very plug and play. In the item description it says everything you need included, true plug and play except I need to get a hood pin!
Ok I need help how do I turn it off I did exactly u did but the instructions say I gotta connect more wires to my immobilizer on 2006 dodge charger do I need to do that or no
i did i have the fortin evo all chrt 4 t harness wire samething and when i have everything wired and use the electric start it wont let me shift my car out if gear have to shut off the car and turn it back on what can i try or do its a 2009 jeep grand cherokee
Man!!!! Thanks! I regret now not doing a bit more research to find you guys! I would have ordered the unit from you.... nevertheless, without this video I would be lost. I got the unit from AMAZON along with the Flasher and could not get it to sync up with my car. I saw this video and was done in like 10 min! Now, I did exactly what you did... i kean exactly! From cutting the wires to the zip tie at the end.... can I still add the mobile module on it?
Hi! I got a EVO-CHRT5 EVO-ALL (SN001A07 116497) I'm trying to install in a 2005 Jeep Grand Cherokee but don't work. The blue light came out but once you put the ignition switch in on position the blue light turn off... Please can you help me to fix it? I think the module don't work...
I tried using the Vague instructions that came in the box but it does not work . I plug into key barrel, Then power wire to box while holding button, release when blue then plug rest of wires and then put key to on position and then remove key and press unlock. Did I do a step wrong?
Hello. I'm checking to see if this device will work on a '14 Chrysler 300? I also looked on the Ebay store website but wasn't sure which product to choose. I appreciate any help given.
I was wondering if once this is done if the remote would still work to unlock and lock the doors. And I was wondering if this is available for a 2014 Dodge Dart?
I got evo rs chat 4 from Amazon for my 2015 crysler t&c . I installed it took some extra time , anyway it starts and after 3-4 seconds it stops and after few seconds automatically it starts again and after 3-4 seconds it stops again. can you please tell me what is the problem ? Thanks
completed programming, all looks good, blue light flashed rapidly then stopped after hitting the lock button. BUT...when trying to remote start, I'm not getting it to crank (the light on the module blinks blue each time I hit it (3x) but then nothing. Any help would be appreciated!
@@Lesscoelectronics so....the plugs on the harness I got were way to big to fit into push button switch....I didn't get it from you but wanted to point it out to you so you know things changed in 18. not sure where to go here, gonna return it for now
I buy the chrt5 for my 06 Dodge Ram it don’t work. To be honest i think it was I waist of money cuz I don’t know what to do with this kit anymore. Can you help me up. What do I believe is this kid it’s not programmed for my truck. Thank you
mux is short for multiplex, all that is - is multiple resistance values travel down a single wire and prompt the computer to perform multiple functions using less wiring and save automakers money building cars. a jeep usually needs 1000 ohms through a negative signal to do parking lights by the way...
Yes I do, see below: www.ebay.com/itm/OEM-Activated-Plug-and-Play-Remote-Start-for-2019-Dodge-Durango-Push-To-Start/401777649099?hash=item5d8bd065cb:g:LjEAAOSwp-Racx5r
Thanks for this video. I bought evo fortin chrt 4 for my Dodge Charger 2010. This video was really helpful. Did exactly like this. Now I’ve a remote start in my car😊
my man! welcome to da club
Definitely not the easiest I've seen in regards to plug n play. Better options out there.
Hy thanks for your time.
It's amazing and I was wondering if it can be fitted to 2018 dodge charger and price please.
I'm looking to install remote start on my 2004 dodge Dakota it has manual door locks what kit do I need and do you offer one
Hey Man, thanks for your instruction. I have managed to connect this R.S. to my 2012 Ram Caravan. Not even Fortin's web site was useful..
I got one for a 2016, ordered it off ebay but the instructions are way too confusing. It is the evo one with only the t-harness. I am attempting to install tomorrow but I also didn't get a install instructions manual just the one available online. Any info on how to wire this one to work like how you did with this one?
sure, whats the vehicle details?
Its a 2016 dodge journey with a push button start. I was attempting to bench set up the wire harness like you did but I only have the one yellow wire off the top harness. It says I have to wire the can-hi and can-low but has 2 wires for each (2 for hi, 2 for low) one set is orange and the other set is grey. I figured I would wire the power that goes to the ignition straight from the push button harness and avoid any problems with hooking up the wrong wire off the main harness. Any help would be greatly appreciated! I would have ordered yours if it would have shown up in the ebay listing but it only showed up when I searched for it by your company name sadly.
I ordered the evo-all version
Hi ... I really need help 😫...
I bought I bought the Excalibur RS-275-3DB BECAUSE IT SAYS WAS A PLUG AND PLAY BUT THIS THING HAS TOOO MANY CABLES.. CAN YOU PLEASE TELL ME WHAT TO DO ...I NEED HELP.
I Installed a Fortin EVO - All in a 2008 Jeep Liberty 4WD
For a year it worked perfectly
Now when I use the remote to start and then shut down or turn off the Jeep
The next time I either use the remote or Key to start the starter over engages for about three seconds
If I shut the car off with either the remote or key it doesn’t over engage the starter
But if I use the remote again to start the car the whole process starts again
I have done a master reset and reprogrammed a total of three times
But the problem persists
Any help would be greatly appreciated.
I don’t want to destroy my starter
Hello my name is Chuck. I have a 2002 Chrysler Town and Country.I would like to know what it cost me for one of those setups I'll plug and play like you just
does it work the same for grand cherokee 2005, it works on evo chrt-5
Still waiting to find out how much it will cost me for you to hook one of these up so I can plug and play in a 2002 Chrysler Town and country and what it would cost
I have bought one for my 2005 vrand Cheroke, tried to install it but when i reached programming the evo device will keep on flashinh all the lights even with the button is pressed
Could you plz help
Mine didn't come with the hood pin and a few other things you mentioned. Not very plug and play. In the item description it says everything you need included, true plug and play except I need to get a hood pin!
no, that hood pin is totally optional.
Ok I need help how do I turn it off I did exactly u did but the instructions say I gotta connect more wires to my immobilizer on 2006 dodge charger do I need to do that or no
i did i have the fortin evo all chrt 4 t harness wire samething and when i have everything wired and use the electric start it wont let me shift my car out if gear have to shut off the car and turn it back on what can i try or do its a 2009 jeep grand cherokee
Which remote start for I need for my pt cruiser 2005 emobilizer
Can you do one for a 2007 2500 dodge truck and what will it cost
That connection can be used in a 2005 Jeep Grand Cherokee??????
06 ram do I need a 12v yellow wire run. In Junction with the t harness.
Hello, do you have a video on how to pre wire the evo chrt7 for a 2014 dodge dart?
Man!!!! Thanks! I regret now not doing a bit more research to find you guys! I would have ordered the unit from you.... nevertheless, without this video I would be lost. I got the unit from AMAZON along with the Flasher and could not get it to sync up with my car. I saw this video and was done in like 10 min!
Now, I did exactly what you did... i kean exactly! From cutting the wires to the zip tie at the end.... can I still add the mobile module on it?
;I
Hi! I got a EVO-CHRT5 EVO-ALL (SN001A07 116497) I'm trying to install in a 2005 Jeep Grand Cherokee but don't work. The blue light came out but once you put the ignition switch in on position the blue light turn off... Please can you help me to fix it? I think the module don't work...
Do we need to cut the yellow wire near the ignition plug and connect it to yellow/green on the red 4 pin? On the manual its the labeled D1.
Hello, you have for grand cherokee 2015 6c
Any way you could do one, Flashlogic FLRSCH5 for a 2007 Dodge Charger. There are no videos or help anywhere. I am having issues getting it to work.
Will it work on 2007 dodge ram 1500?
Is the chart 5 harness the same set up
Got anything for a 2009 dodge charger 3.5L?
How can i make this for evo-chrt6? I got a jeep grand cherokee 2018.
Would it work that way on jeep Cherokee srt8 2007 I just got one off you guys and not too sure how to fit it
did you look up the install guide on fortin.ca?
@@Lesscoelectronics yes but cart seem to work it out
I tried using the Vague instructions that came in the box but it does not work . I plug into key barrel, Then power wire to box while holding button, release when blue then plug rest of wires and then put key to on position and then remove key and press unlock. Did I do a step wrong?
It sure sounds like it, Whats your year make and model?
@@Lesscoelectronics I have a 2011 VW Routan . Also it's a Evo RS CHR.T4
Thanks for the video.
Hello. I'm checking to see if this device will work on a '14 Chrysler 300? I also looked on the Ebay store website but wasn't sure which product to choose. I appreciate any help given.
Can you fix one for my 2005 pt cruiser or will that one work? I have a fortin
sure, call us 904 342 5491
I was wondering if once this is done if the remote would still work to unlock and lock the doors. And I was wondering if this is available for a 2014 Dodge Dart?
Same
Do you have for 2015 chrysler 200?
Do you have one for 2017 dodge journey push to start?
do the wires need to be cut at all [apart from connecting the yellow one?] will it be a problem if I don't?
thanks
even if you're not using the hood pin or parking lights
I got evo rs chat 4 from Amazon for my 2015 crysler t&c . I installed it took some extra time , anyway it starts and after 3-4 seconds it stops and after few seconds automatically it starts again and after 3-4 seconds it stops again. can you please tell me what is the problem ? Thanks
Is there a link to a pre wired kit for a 2015 ram 3500 diesel
Yes, here it is www.ebay.com/itm/363296912785
Will you guys ever do an update for the Chrysler 200 with the CHRT-6 T Hardness?
Maybe, whats are you most interested in exactly?
How can i do this on evo-chrt6? My t harness not has the yellow wire.
Is this the same for a 2012 dodge avenger with the evo-all evo-chrt5
Do you still have them in stock??
completed programming, all looks good, blue light flashed rapidly then stopped after hitting the lock button. BUT...when trying to remote start, I'm not getting it to crank (the light on the module blinks blue each time I hit it (3x) but then nothing. Any help would be appreciated!
same problem . did you ever get it sorted out?
Does anyone know if this works for a 2011 charger pursuit push to start
will this be the same for a 2018? wish I had got the kit from you...
MMMM, Similar, but 2018's also need a flashlink which I will include so you can do the key clone (decryptor) step yourself.
@@Lesscoelectronics so....the plugs on the harness I got were way to big to fit into push button switch....I didn't get it from you but wanted to point it out to you so you know things changed in 18. not sure where to go here, gonna return it for now
ordered the new t6 version from amazon but it had a t5 sticker showing so not sure what they did...
if the plugs arent grey then you ain't got the right plug.
@@Lesscoelectronics yup they were black and 2x the size do you have the correct one for a 2018?
I do the connection on my 2011 ram 1500 and the three colors red yellow and blue still flashing all the time. Can you give a hand. Please.
Call me tomorrow, Ill help - no biggie 904 342 5491, Martin
do you have kits for the dodge journey 2019 and if so how much for a preprogrammed unit
Yes sir!
www.ebay.com/itm/401978014558
Do you make the remote start for a 2020 chrysler 300?
There’s no 2020 Chrysler 300 u dummy
Can you do that with any remote starter ?
Can you make one for pt cruiser 2004 ?
installing this kit 'SHOULD' enable my remote start on my key fob?
never mind - this is a totally separate system from OEM. NICE!!!
yes sir
this is way HELLA cheaper than having the dealership diagnose why my remote start isn't working... that's a fact...
So how important is the installation Of the hood pin switch?
its an optional layer of protection, it not for everyone, but it is safer to use one..
I thought they had one for dodge dart push button start didn't have or work
You have kit for Chrysler Pt cruiser 2004? $?
no sorry, only 2006 and later
Thanks
Is their one for a 2004 dodge ram
no, sorry
I buy the chrt5 for my 06 Dodge Ram it don’t work. To be honest i think it was I waist of money cuz I don’t know what to do with this kit anymore. Can you help me up. What do I believe is this kid it’s not programmed for my truck. Thank you
What is the service number on the evo module?
how i can connect parking light cable into 2010 jeep compass and what its mean MUX cable ?
mux is short for multiplex, all that is - is multiple resistance values travel down a single wire and prompt the computer to perform multiple functions using less wiring and save automakers money building cars. a jeep usually needs 1000 ohms through a negative signal to do parking lights by the way...
Lessco Electronics will this set up work for dodge dart i have the evo chrt 6
Are these still offered on your site for a 2013 Dodge Dart?
check it out: www.ebaystores.com/Lessco-Electronics/_i.html?_nkw=2013+dart&submit=Search&_sid=77826561
Can they fit on a Ram Ecodiesel?
What year?
Do you have one for a 2019 Dodge Durango GT?
Yes I do, see below:
www.ebay.com/itm/OEM-Activated-Plug-and-Play-Remote-Start-for-2019-Dodge-Durango-Push-To-Start/401777649099?hash=item5d8bd065cb:g:LjEAAOSwp-Racx5r
I bought a prelaoded one for my ram followed your steps and programming steps and it doesnt work for me.
I cant get mine to start in the mornings but after i drive it for a lottle and try to start it some other time in the day it works
Did you get that item from us?
replace your car battery
Can you make one for Honda Pilot 2003
I cannot, an 03 pre-dates canbus technology which these kits are designed to be used with predominantly.
Does it activate the parking lights with remote start on?
Yes, ON most kits the brown/white output has a -output for that specific purpose.
It will if you tie in the brown/white wire output
add a 1k ohm resistor though!!
I did everything in the video flashed it and programed it but it won't start my car
What about the can high and can low?
theyre in the t harness already
I have audi a4 2012 is same?
Yes, I have them here:
www.ebay.com/sch/m.html?_ssn=martinhod&LH_PrefLoc=&_from=R40&_trksid=p2499338.m570.l1313&_nkw=a4&_sacat=0
08?..... like a Jeep Compass?
Ok I have it flashed and programmed plugged back in now I’m just getting a flashing blue light but won’t start
Did you program it to the car before trying to use it??
Yes I read I might have to master reset and program again
Ugh, you dont want to do a master reset, you'll go more backwards than anything doing that...
Got a link to green and black strippers
these? www.ebay.com/str/lesscoelectronics?_bkw=strippers
Green and black handle u used on video also do u make a plug and plAy remote start 2009 toyota tacoma
Thx
I don't have a emobiliser
good video....but you can be a little slower and show the color or name the colors of the wires you cut......
Please email me the request via email to: sales@lesscoelectronics.com - I will reply with one for you.
This guy is too fast. Either he wants to save time or data. No option but to watch the video at half the speed 😂😂😂😂
You need to slow down
never happen
Wow... maybe drink less coffee before filming.... couldn’t follow at all.
Do you have a kit for a 2019 Dodge Challenger SXT
www.ebaystores.com/Lessco-Electronics/_i.html?_nkw=+challenger&submit=Search&_sid=77826561
What can i use for 2017 dodge journey push start??
Those are super easy , probably under 15min, I just did my 2018 going to upload the video to my channel
Is this the same way for the evo-chr t6?
What model 2016?
2012 Chrysler 300
yes its very similar
Ok cool only difference is one yellow on the main pin and the other yellow with blue stripe
the chrt6 has 2-4 extra connections and always required the decryptor step at the end to clone a key while using it.
will this work on a 2017 Challenger RT
Which kit do i need for 2018 dodge ram 15oo
this one: www.ebaystores.com/Lessco-Electronics/_i.html?_nkw=2018+ram+&submit=Search&_sid=77826561