thanks alot dude, with ur help i really got into subd modelling with rhino and its such an amazing tool. My Co-Students always ask me how i did create my buildings and i always refer to ur channel cause ur tutorials are awesome
Thanks, I used the Grasshopper for the first time, I had a problem with Boundary Surfaces, the left receiver could accept only one wire (idk the names forgive me haha) either from Relay or Rebuild Cruve.. later after flwing all instructions, the result was applied on both surfaces (tho Im pretty sure I selected the down surface)
@@AdamArchh you are welcome. Can I one question? I tried to make what you did fully in Grasshopper. Everything was good except one. The one that I had problem with was 'Surface split'. I could not find the option or command(Node) to shrink the domain when the surface trimmed. IF YOF HAVE TIME ONLY, could you please show the script or recommend some tutorial. It will be very appreciated. Thanks!!
Honestly your tutorials help me a lots in the way of learning how to modelling with Rhino. Big respect. I also have a question: 1. what is the purpose of "Bounding box" component and why do we have to connect its output to Reference of "Surface Morph" ? 2. What's the difference between Deconstruct Domain (with U max and V max) at the first stage and Deconstruct Domain without it (normal U and V output) ? Thank you and have a good day
at 1;09 when you scaled the edge loop , that didnt happen for me , i endup scaling the whole object even when pressing shift/ ctrl i tried whatever but it didnt work , thank u for the vid
Nice, but is there any way to know the base of grasshopper? Because when ever you use it in your lessons I just don't have any idea about it and I repeat your moves😂
I have a couple problems with the exercice: 1. when I Scale the Voronoi cell around 0.70/0.75 some cells create a surface inside of them. The vast majority have holes but some near the perimeter dont (i followed the tutorial step by step) 2. Until the Extrusion everything works if I Scale it slightly smaller (0.60), but when the BoundingBox receives the Extrusion data it creates a boundingbox bigger than the Extrusion. The boundingbox is where the extrusion sits, and as they are differently scaled, the final product is floating (the perimeter of the baked SurfaceMorph isnt connected with the other hald of the stadium) Thanks in advance!
I tried lot of time selection is so complex in this rhino... I strucked at the grasshopper node surface --- set one surface. When ever i try to slect nothig selected
thanks Adam! great vedio again! At 7:17 in this vedio, I wonder why "Boundary Surface" doesn't show out result while all former steps are fine? what may be the problem? :)
Merhaba, SubD araçları yalnızca Rhino 7 ve üstü versiyonlarda kullanılabiliyor. 90 günlük Rhino 7 deneme sürümü indirebilirsiniz. Ya da Rhinoceros 5 indirip T-Splines eklentisini kurebilirsiniz. Bu SubD'nin ilk versiyonu olduğu için SubD kadar başarılı değil.
The images in the video are not renders, they are photos of the real project. - archdaily.com/562054/football-stadium-arena-borisov-ofis-architects I use 3Ds Max + Corona Renderer in my own projects.
Hola, tengo un problema en el minuto 7:31 al añadir el relay no me deja conectarlo a la caja de boundary surfaces, si conecto el relay se desconecta rebuild curve
Başka bir model üzerinde aşmaları takip ediyordum, parametreleri değiştirince halloldu. İlginiz için ve bilgilendirici videolar için çok teşekkürler! @@AdamArchh
from 2:16 , you only selected 6 loops of edges. but after duplicating. you got 7 curves ? I did it the same way. but kind of bit confused. how did the curve at the bottom come out ?
@@AdamArchh after many tries. I finally achieved the correct result. I have learnt much from this video. plz make more of the good tutorials. will keep following you.
HI! I have an initial problem, when I create the two 8 meter surfaces, subsequently it doesn't let me deform the walls, can you tell me why? I also read a comment where you asked the same thing, but I have gumball active and I tried the other option. When I move the red line, it scales the model uniformly, without deforming it
I have the same problem, it gives me as if it is a single surface, it doesn't make me select the line in the middle but the entire surface. I've been trying for a long time but I can't. We are waiting for a response!!
Hi. Adam. sorry. I've got an issue again. 8:36 when creating the bounding box. my bounding box is much larger than the extrusion object. it's almost twice of the width. any idea how that's happening ? thanks.
Hi there Ray Wong, I've never had a problem like this. But if you want, you can create a manual bounding box yourself by extruding the rectangle we created first. Google Drive: drive.google.com/drive/folders/1me8ztcmdwz2tEN-FBmRRdK8yyXiHgxWO?usp=sharing
When spliting a SubD the split command does not expose the shrink argument, you would have to reparametrize the split surface or handle this inside grasshopper, otherwise the voronoi pattern would remap to the whole original surface before the split and not just the split part.
Hello, How could someone begin learning Rhino + Grasshopper from scratch as a newbie, i am actually an architecture student and would love to learn because the software fascinates me and opens door for all kind of designs for, i'd be happiest if you could help me by referring tutorial videos to learn the software from the beginning :) Thank You.
Hey, As a Rather recent Architecture school graduate, and someone who loves Rhino and is still learning always. You will definitely learn everything you need to know by watching tutorials here on RUclips and of course from this channel! As i am a recent sub myself. Practice is key! So always have rhino open and practice as you watch and you will in no time learn the basics of rhino first then Grasshopper. Focus on Rhino first
Our tutorials are intermediate level tutorials . And we are project-oriented. So you can find lots of beginner-level tutorials on RUclips. It makes more sense to learn Rhino first and then Grasshopper.
The relay from the rectangle to boundary surfaces unlinks rubuild curve link to boundary surface
thanks alot dude, with ur help i really got into subd modelling with rhino and its such an amazing tool. My Co-Students always ask me how i did create my buildings and i always refer to ur channel cause ur tutorials are awesome
Wow thank you, good to hear.
Amazing work. Your vedios make me learn a lot.
Thank you for your support
Many thanks Adam. Great tutorial as usual!
Thank you too
Thx for your passion... you're a pro!
Thank you
The channel will grow
Extremely useful video. Got to learn lots of new things. Keep it up.
Thank you
thanks for ur fantastic demo . its really helpful to learn how to create model.
Thank you
Jesus this is superb.
Thank you
Amazing design,like this 😍
Thanks for great tutorials :D
Thank you
Incredible
Thank you
Thank you for your efforts.
I hope you clarify the bif more because it didn't give a result with me please
Thanks, I used the Grasshopper for the first time, I had a problem with Boundary Surfaces, the left receiver could accept only one wire (idk the names forgive me haha) either from Relay or Rebuild Cruve.. later after flwing all instructions, the result was applied on both surfaces (tho Im pretty sure I selected the down surface)
With shift you make a copy and you can paste the relay, did you manage to make the coverage?
Thanks a lot! your tutorial is super!
Thank you
@@AdamArchh you are welcome. Can I one question? I tried to make what you did fully in Grasshopper. Everything was good except one. The one that I had problem with was 'Surface split'. I could not find the option or command(Node) to shrink the domain when the surface trimmed. IF YOF HAVE TIME ONLY, could you please show the script or recommend some tutorial. It will be very appreciated. Thanks!!
Great 👍
Please can you use Revit for this exact same design?
Honestly your tutorials help me a lots in the way of learning how to modelling with Rhino. Big respect. I also have a question:
1. what is the purpose of "Bounding box" component and why do we have to connect its output to Reference of "Surface Morph" ?
2. What's the difference between Deconstruct Domain (with U max and V max) at the first stage and Deconstruct Domain without it (normal U and V output) ?
Thank you and have a good day
Bounding Box is the smallest surface eclosing the geometry
Hi Adam, I followed the steps but the sides didn't turn out well, maybe it's because I'm now using Rhino 8?
Great tutoriaal! I have a question, how would you fix the problem or the "not continuous voronoi" in the seam line?
at 1;09 when you scaled the edge loop , that didnt happen for me , i endup scaling the whole object even when pressing shift/ ctrl i tried whatever but it didnt work , thank u for the vid
- Use the Gumball so scale 1D
- Hold shift to scale proportionally
mennn where have you been!!!!!??????? awsemone techiques
Thank you
Nice, but is there any way to know the base of grasshopper?
Because when ever you use it in your lessons I just don't have any idea about it and I repeat your moves😂
Thanks. You can find thousands of beginner's tutorials on RUclips.
I hear ya! It's like.....WHEREDAFAk do I start?
Çok güzel, çok eğitici. Teşekkürler.
Ben teşekkür ederim.
How to change the size of one circle ( tlorganic thing ) in the pattern what i mean what if i want to increase the size of one of them
I have a couple problems with the exercice:
1. when I Scale the Voronoi cell around 0.70/0.75 some cells create a surface inside of them. The vast majority have holes but some near the perimeter dont (i followed the tutorial step by step)
2. Until the Extrusion everything works if I Scale it slightly smaller (0.60), but when the BoundingBox receives the Extrusion data it creates a boundingbox bigger than the Extrusion.
The boundingbox is where the extrusion sits, and as they are differently scaled, the final product is floating (the perimeter of the baked SurfaceMorph isnt connected with the other hald of the stadium)
Thanks in advance!
Did you find a solution for that ?
great
Thank you Ali
How did you create glass surface inside
I tried lot of time selection is so complex in this rhino... I strucked at the grasshopper node surface --- set one surface. When ever i try to slect nothig selected
thanks Adam! great vedio again! At 7:17 in this vedio, I wonder why "Boundary Surface" doesn't show out result while all former steps are fine? what may be the problem? :)
I found the problem! I accidentally unpreview the result. Now "Boundary Surface" works! thanks again ;)
Merhabalar rhino 6 kullanıyorum. Makesubd komutu çıkmıyor ne yapmalıyım acaba?
Merhaba, SubD araçları yalnızca Rhino 7 ve üstü versiyonlarda kullanılabiliyor. 90 günlük Rhino 7 deneme sürümü indirebilirsiniz. Ya da Rhinoceros 5 indirip T-Splines eklentisini kurebilirsiniz. Bu SubD'nin ilk versiyonu olduğu için SubD kadar başarılı değil.
Can somebody help me out ? Like creating similar thing but on a rectangular surface ??
👍🏻👍🏻👍🏻👍🏻👍🏻😍
What did you use for the render?
The images in the video are not renders, they are photos of the real project.
- archdaily.com/562054/football-stadium-arena-borisov-ofis-architects
I use 3Ds Max + Corona Renderer in my own projects.
at the beginning when u say extrude u talk about extrudeCrv ?
I mean Extrude using Gumball.
2. image: instagram.com/p/Cu2c6VQswCH/?igshid=MzRlODBiNWFlZA==
thannks Adamm i dont know why the number slider give me a maximum "1 " as value u put 150 @@AdamArchh
@@ghazinspace Double click on the canvas and type 150 enter
it said that lower limit is 0 and upper limit is 1 ... @@AdamArchh
Double click the number slider and change the Max value
Hola, tengo un problema en el minuto 7:31 al añadir el relay no me deja conectarlo a la caja de boundary surfaces, si conecto el relay se desconecta rebuild curve
SAME ISSUE
Haz una copia manteniendo seleccionado la tecla shif, si te das cuenta se crea un símbolo mas
merhaba, voronoi yüzeyim ana yüzeyi tam kaplamıyor eksik alanlar kalıyor. Sebebi ne olabilir?
Merhaba, birçok nedeni olabilir. Buradan bir şey söyleyebilmek mümkün değil.
Başka bir model üzerinde aşmaları takip ediyordum, parametreleri değiştirince halloldu. İlginiz için ve bilgilendirici videolar için çok teşekkürler! @@AdamArchh
ZH style..
from 2:16 , you only selected 6 loops of edges. but after duplicating. you got 7 curves ? I did it the same way. but kind of bit confused. how did the curve at the bottom come out ?
That curve was the ellipse we drew at the beginning of the tutorial.
hahaha. it seems that I asked a silly question. obviously. yes. we did. at the very beginning. thank you very much Adam.
Every question is logical.
@@AdamArchh after many tries. I finally achieved the correct result. I have learnt much from this video. plz make more of the good tutorials. will keep following you.
HI! I have an initial problem, when I create the two 8 meter surfaces, subsequently it doesn't let me deform the walls, can you tell me why? I also read a comment where you asked the same thing, but I have gumball active and I tried the other option. When I move the red line, it scales the model uniformly, without deforming it
I have the same problem, it gives me as if it is a single surface, it doesn't make me select the line in the middle but the entire surface. I've been trying for a long time but I can't. We are waiting for a response!!
SubD menu ---> look very corner are of that icon collection u have an options like face select, edge select , point and edge loop select
Hi. Adam. sorry. I've got an issue again. 8:36 when creating the bounding box. my bounding box is much larger than the extrusion object. it's almost twice of the width. any idea how that's happening ? thanks.
Hi there
Ray Wong, I've never had a problem like this. But if you want, you can create a manual bounding box yourself by extruding the rectangle we created first.
Google Drive: drive.google.com/drive/folders/1me8ztcmdwz2tEN-FBmRRdK8yyXiHgxWO?usp=sharing
@@AdamArchh I suffered from the same problem, but I solved it by setting the bounding box myself.
Thank you
@@きくきく-h8k Please, I have the same problem, how can I set the bounding box myself ?
@@ibtissamdaher8794 I solved it by manually adjusting the bounding box.
@@きくきく-h8k how do you manually adjust the bounding box?
Elinize sağlık.Türk müsünüz acaba :)
Teşekkür ederim. Evet Vanlıyım.
Tebrikler..Başarılarınız daim olsun inşallah
Teşekkür ederim. Size de kolay gelsin.
can i ask why we have to convert from subD to loft,please
When spliting a SubD the split command does not expose the shrink argument, you would have to reparametrize the split surface or handle this inside grasshopper, otherwise the voronoi pattern would remap to the whole original surface before the split and not just the split part.
Hello,
How could someone begin learning Rhino + Grasshopper from scratch as a newbie, i am actually an architecture student and would love to learn because the software fascinates me and opens door for all kind of designs for, i'd be happiest if you could help me by referring tutorial videos to learn the software from the beginning :)
Thank You.
Hey,
As a Rather recent Architecture school graduate, and someone who loves Rhino and is still learning always. You will definitely learn everything you need to know by watching tutorials here on RUclips and of course from this channel! As i am a recent sub myself. Practice is key! So always have rhino open and practice as you watch and you will in no time learn the basics of rhino first then Grasshopper. Focus on Rhino first
Our tutorials are intermediate level tutorials . And we are project-oriented. So you can find lots of beginner-level tutorials on RUclips. It makes more sense to learn Rhino first and then Grasshopper.
Thanks Fab C, for the great comment.
@@fabc9841 thanks man...really appreciate your comment
@@AdamArchh okk will definitely start by learning rhino first :)