Today I replaced my brewing piston it had a crack on the plastics, my machines around 8 years its now good as new. Without this video I wouldn't have been able to fix it! Thank you for making this awesome video!
Thank you, was a big help to see how to do this procedure. I was lucky and needed only cleaning. Mine is a Magnifica S, but internal bits are the same, only without the LCD display.
Thank you for your kind words! As I said before, I am not an engineer, I just had a go and when the parts arrived I thought I will film it (Including any mistakes) and it may help someone. Glad to hear that it did help. Many thanks.
Thanks for the tutorial. I saw that on the piston top part, there is a switch which not in contact with any part that might be able to push it. However, I think that when the infuser is going up toward the piston, by pressing really hard, the two springs from the piston, it might be possible to have this switch pushed and therefore triggering an event. On my ECAM 22.110.B, I have a yellow triangle light which is flashing and looking when this happens is at the moment described above. I tried to press the piston part in order to see if it can move and, indded, that is possibel but it's hard to make it moving (the spriongs are really hard to press). Do you have a hint for this yellow flashing light ? Thanks again
You haven't notice the small amount of water on top of the piston, was it a small leak? Have you forget to clean the condensation output on the left front side, lots of lime scale?
Hi, Thanks a lot for all your vid I bought my DeLonghi Magnifica XS from Costco MN 120 v - 60 HZ 1250 W Type ECAM 22110 B P= 1.5 MPa (15 bar) When I took it to North Africa and by mistake I plugged it in 220 V I smelled little burning. I still can turn it on I can hear the coffee grinding all screen look good with green and yellow light but it doesn't dispense water nor a coffee. Please help.
Sorry, I am no expert! I just fixed my machine and made a video of it, to include any mistakes I made, so others can avoid the mistakes and maybe assist them in fixing their machines. You seem to have an electrical problem and fused part of the circuit. Take it to a local repair person, Good luck!
First of all, thank you for sharing you knowledge! After I replaced the o-rings and put it back together to make the test, the unit turns on (but not flushing water through) and the red light “Triangle !” comes on. I have tried to turn off, take electricity of the plug in the wall. Any suggestions?
Firstly; I am no "Expert", I just made a video to include all mistakes I made, so people can follow what seems right to them! There are a lot of youtube videos explaining many problems. Just do a search on youtube. I hope this helps you to find a solution.
1.48. better to move cover back about cm1 backward, both sides. Then undo the 2 side screws holding the lid on. This will help prevent damage to the catches at the top and bottom on the side panels. 2.35 after removing the steamer control pull the grinder control, located under the coffee lid, but pulling straight up. Only then lift the lid followed by the side panels. Remember DON'T LIFT LID IF SIDE PANELS ARE NOT MOVED BACK ABOUT 1cm. The cracked, yellow see through part, can be bought independently although as the price isn't much cheaper that's up to you. An advantage of the complete new unit is all the o rings are new.
Hi David. A wonderful video. Its fantastic. Have you any suggestions on replacing the Hall Sensor. The grinder works fine although its not grinding long enough. I reset the system and it grinded too much coffee first time and i chmaged the strength and it produced the best cup of coffee since buying this machine. After this cup the grinding once again became very quick producing very weak coffee. Ive done some research and its most likely a faulty hall sensor. Any help or advive would be greatly appreciated
Sorry, I won't be able to help you. I had never seen the inside of one of these before! So I opened it (before making the video) and realised the generator was cracked. I ordered it from ebay. Then I thought I would make a video while replacing it. I was sure I would make lots of mistakes, but others can avoid my mistakes and probably manage to fix their machine. After a quick search on youtube I found this vwebsite: (Maybe it will help you) www.coffeeforums.co.uk/threads/problem-with-delonghi-magnificas.25619/
I have a Delonghi Magnifica S is dumping water into the coffee grounds container I am trying to find a solution to this problem, could it be the O RING that's also an with it?
@@DavidLevi-k1 opened it up and found a crack in the Delonghi Brew Piston Infuser and can see it leaking, this will need replacing like yours. I am in the UK so will see if I can buy a replacement part! thanks for the video its great!!
Hi Richard, Firstly; I am no "Expert", I just made a video to include all mistakes I made, so people can follow what seems right to them! There are a lot of youtube videos explaining the removal of the Infuser. Just do a search for "magnifica s clean infuser". I hope this helps you to find a solution.
Hello. After 6 years using the machine coffee taste got very bad. Used coffee tablets residue are not whole and wet. I've changed the brewing piston and all O rings, cleaned everything inside. Coffee taste got better and the coffee tablets are still broken and very wet. What is the reason can be? Thanks
Hi David. In the video you refer to getting the replacement part from e-spares. Can you give me a reference part number for the part you used. I need to purchase the same part for this coffee machine but e-spares have at least 3 different parts for this coffee machine. Want to make sure I buy the right one.
Hi Liam, I'm sorry but I cannot help you. I provided the model number and there was only one option. Currently, I do not have the machine, as I have upgraded and never kept the receipt.
Today I replaced my brewing piston it had a crack on the plastics, my machines around 8 years its now good as new. Without this video I wouldn't have been able to fix it! Thank you for making this awesome video!
Thank you, was a big help to see how to do this procedure. I was lucky and needed only cleaning. Mine is a Magnifica S, but internal bits are the same, only without the LCD display.
Thank you very much for the time you took to explain step by step. it helped me a lot to repair my Dinamica Delonghi. thanks again.
Thank you for your kind words! As I said before, I am not an engineer, I just had a go and when the parts arrived I thought I will film it (Including any mistakes) and it may help someone. Glad to hear that it did help. Many thanks.
Wonderful step by step explanation.
Thanks! Glad to see that the video continues to help people.
Thanks for the tutorial.
I saw that on the piston top part, there is a switch which not in contact with any part that might be able to push it. However, I think that when the infuser is going up toward the piston, by pressing really hard, the two springs from the piston, it might be possible to have this switch pushed and therefore triggering an event.
On my ECAM 22.110.B, I have a yellow triangle light which is flashing and looking when this happens is at the moment described above.
I tried to press the piston part in order to see if it can move and, indded, that is possibel but it's hard to make it moving (the spriongs are really hard to press).
Do you have a hint for this yellow flashing light ?
Thanks again
Thank you, thank you, thank you very much for your disponibility to share your knowledge with us. Chears from Roumania!
Top Job ! well done thank you for sharing your willingness to improve our general knowledge .
Fantastic video David.
Love it. Helped me with my repair. Cheers!
Thank you for watching the video! Glad it helped another person with their problem.
You haven't notice the small amount of water on top of the piston, was it a small leak? Have you forget to clean the condensation output on the left front side, lots of lime scale?
Hi,
Thanks a lot for all your vid
I bought my DeLonghi Magnifica XS from Costco MN
120 v - 60 HZ 1250 W
Type ECAM 22110 B
P= 1.5 MPa (15 bar)
When I took it to North Africa and by mistake I plugged it in 220 V
I smelled little burning. I still can turn it on I can hear the coffee grinding all screen look good with green and yellow light but it doesn't dispense water nor a coffee.
Please help.
Sorry, I am no expert! I just fixed my machine and made a video of it, to include any mistakes I made, so others can avoid the mistakes and maybe assist them in fixing their machines.
You seem to have an electrical problem and fused part of the circuit. Take it to a local repair person,
Good luck!
First of all, thank you for sharing you knowledge!
After I replaced the o-rings and put it back together to make the test, the unit turns on (but not flushing water through) and the red light “Triangle !” comes on.
I have tried to turn off, take electricity of the plug in the wall.
Any suggestions?
Firstly; I am no "Expert", I just made a video to include all mistakes I made, so people can follow what seems right to them! There are a lot of youtube videos explaining many problems. Just do a search on youtube.
I hope this helps you to find a solution.
Hi again, i figured out the issue. Thank you though
@@filiplarsen1434 Hi, Please do share with us, how you fixed it? Many people visit this video looking for solutions. Maybe it will help others.
Great video David. I have a refurb to carry out on a similar model so will be using vid as a reference.
MAJOR MISTAKE: Made at 28:05 and 34:12 - Spring inserted WRONG-WAY round !!!
Thanks for the info David. 👍
Hello, this helps also for leaking water in the disposel tray?
There could be a multitude of problems for the leaking.
In my case the generator was cracked. But it could also be that the seals need replacing.
1.48. better to move cover back about cm1 backward, both sides. Then undo the 2 side screws holding the lid on. This will help prevent damage to the catches at the top and bottom on the side panels. 2.35 after removing the steamer control pull the grinder control, located under the coffee lid, but pulling straight up. Only then lift the lid followed by the side panels. Remember DON'T LIFT LID IF SIDE PANELS ARE NOT MOVED BACK ABOUT 1cm.
The cracked, yellow see through part, can be bought independently although as the price isn't much cheaper that's up to you. An advantage of the complete new unit is all the o rings are new.
Thank you for these comments - I am sure it will help someone!
@@DavidLevi-k1 and thanks for your video. It helped me.
Hi David. A wonderful video. Its fantastic. Have you any suggestions on replacing the Hall Sensor. The grinder works fine although its not grinding long enough. I reset the system and it grinded too much coffee first time and i chmaged the strength and it produced the best cup of coffee since buying this machine. After this cup the grinding once again became very quick producing very weak coffee. Ive done some research and its most likely a faulty hall sensor. Any help or advive would be greatly appreciated
Sorry, I won't be able to help you. I had never seen the inside of one of these before! So I opened it (before making the video) and realised the generator was cracked. I ordered it from ebay. Then I thought I would make a video while replacing it. I was sure I would make lots of mistakes, but others can avoid my mistakes and probably manage to fix their machine. After a quick search on youtube I found this vwebsite: (Maybe it will help you)
www.coffeeforums.co.uk/threads/problem-with-delonghi-magnificas.25619/
@@DavidLevi-k1 you did an amazing job. This video helped me fix the boiking water and frothing part of the machine. Thank you kindly for this.
@@samuelconneely3010 Thank you for your kind words!
I have a Delonghi Magnifica S is dumping water into the coffee grounds container I am trying to find a solution to this problem, could it be the O RING that's also an with it?
It could be the O ring - I cannot say for sure.
@@DavidLevi-k1 opened it up and found a crack in the Delonghi Brew Piston Infuser and can see it leaking, this will need replacing like yours. I am in the UK so will see if I can buy a replacement part! thanks for the video its great!!
Infuser in my Magnifica XS is solid stuck in upper position(not visible through the open gate) How to force it down to removable position
Hi Richard, Firstly; I am no "Expert", I just made a video to include all mistakes I made, so people can follow what seems right to them! There are a lot of youtube videos explaining the removal of the Infuser. Just do a search for "magnifica s clean infuser".
I hope this helps you to find a solution.
First stop the machine ..
Hello. After 6 years using the machine coffee taste got very bad. Used coffee tablets residue are not whole and wet. I've changed the brewing piston and all O rings, cleaned everything inside. Coffee taste got better and the coffee tablets are still broken and very wet.
What is the reason can be?
Thanks
Hi Vlad, did you find a solution? I have the same problem
@@paolosacchetti4688 Hi, Paolo. Yes, I did. I cleaned everything where this water comes. Watch this video ruclips.net/video/MevXIJX7SLA/видео.html
13:54
Is Dave medical practitioner?😊
Hahaha, Nice one! I find it a very useful tool, come in handy to access fiddly bits.
Hi David. In the video you refer to getting the replacement part from e-spares. Can you give me a reference part number for the part you used. I need to purchase the same part for this coffee machine but e-spares have at least 3 different parts for this coffee machine. Want to make sure I buy the right one.
Hi Liam, I'm sorry but I cannot help you. I provided the model number and there was only one option. Currently, I do not have the machine, as I have upgraded and never kept the receipt.
DeLonghi Magnifica S Plus ECAM Piston Generator Repair or Replace Part No: 7313244461
OK