I've been using above ground beds for about 15 years. One thing that helps: paint the boards, ESPECIALLY the exposed grain ends, and BEFORE assembly so you get coverage at the joints. They look nicer, and I think you get about double the life. Irrigation: I use a dual-level system. I drill a 3/4 hole in the box side, about 1/3 from the bottom. I run 5/8 main (valve at the entrance to the box if you want to isolate) into the box, tee to each side, elbows along each side (all this 1/3 from bottom). I then connect 1/4 drip tube (integral weep holes) alternating in stripes from the two sides, covering the layer; again, 1/3 from bottom. In each corner I put an above ground 90 degree sprayer, adjustable, with a spray range long enough to cover the size of the bed. When first planting, I use both the above ground sprayers, and the lower (future root) matrix is always active. After the plants have rooted, I turn off the above ground sprayers, leaving only the below ground root system with water. This reduces evaporation, and also discourages surface weeds.
I just built my first dripper system and after I finished I had the idea that I should have set up a similar below ground watering system. Might be back out there on Saturday undoing all of my work.
@@shelshele Gee a video is sooo not-my-generation! :-) Since a year ago, I figured even easier method: the 5/8 (standard plastic irrigation pipe) carries enough water that you can run it down the middle, and serve ALL the 1/4 tubes from one main pipe. Again, put in about 1/3 soil depth, and put the underground dripper grid on top of that soil (then fill the rest). Install the 1/4" laterals about every 6~12", and cut them so the drip holes are staggered, alternatingly. Remember that this lower grid isn't meant to give 100% coverage to seeds/seedlings: it just has to wet the soil "down there", and the roots will grow to the moisture.
One thing I have found helpful when doing drip irrigation in cold temperatures is to use a propane torch with a push button ignitor to slightly heat (be careful not to burn) the ends of the tubing a few seconds before pressing the tubing on the fittings. This works well on the harder poly tubing as well as the 1/4" drip line. I have installed hundreds of feet of drip in my orchard this way in the winter and makes life a lot easier especially when using barbed fittings instead of compression fittings.
Yes, the "new" pressure treated wood is safe for use for raised garden frames... with a few precautions! Up until 2003, the most common preservative used for pressure treated wood was chromated copper arsenate (CCA), a compound using arsenic as its primary rot protectant.The compounds currently being used are alkaline copper quat (ACQ) and copper azole (CA-B). Both contain copper and a fungicide but no arsenic.Yes, New Pressure treated wood is safe.
Thanks! Saved me from freaking out. I just built one with pressure treated pine. But i also plastic lined the walls. Hopefully there was nothing wrong with that :D
Copper is extremely toxic to the body and causes a whole host of issues. Check out The Medical Medium to learn how toxic and problematic copper deposits in the body can be.
This was a wonderful video. Thank you! Wanted to add, pressure treated wood has come a long way in the past years. You can now buy garden safe pressure treated wood that will last you for up to 10 years and costs quite a bit less that douglas fir (and certainly much cheaper than cedar). I have about 300 sq ft of raised garden bed using pressure treated pine, and I come out with about 500-600 pounds of fresh, healthy produce every year. Just check the labelling to ensure the treatment process is such that it is certified as a Environmentally Preferable Product (EPP).
@@warfarewar8206 I don't believe that the old arsenic treated wood can be sold in recent years. Now it's all copper based as another commenter stated and shouldn't be an issue.
That seems like a crazy good amount of food for 500-600 sq ft, could you tell us more such as, what you grow, in what region, and your soil/amendment used
Newer pressure treated wood is actually quite safe to use in the garden! Of course, some people may not feel comfortable with any treated products but MCA, CA-B, and ACQ do not contain arsenic, which was the main concern with earlier types of treated wood such as CCA. They do contain copper, but the amount that would be required for toxicity is far higher than what is typically seen with plants grown in these beds. Un-treated wood is still preferable, but for people who may have issues with rot and pests newer treated products offer a good alternative. And thanks for the video! Looking to make one of these this coming season and install drip irrigation in my other raised beds.
Benjamin Dan good treatment to the timbers then builders Dpc wrapped all round in and out well and correctly then nice free skip timbers ie pallets to clad the out side of the beds for a nice natural look . never replace timbers and lasts 30 years if you don’t clad the face 👍 I like doing it once and well 😊
Another fellow CT resident who likes your videos. This video is exactly what I was looking for. Thanks for showing multiple examples and explaining everything.
Thanks for the video. I have used pressure treated lumber for my raised beds since the feds banned the arsenic infused lumber about 7 years ago. Pressure treated lumber today uses copper to deter rot and works very well for raised beds. The infused copper has an additional benefit, it kills garden fungus just like the copper fungicide that is sprayed on vegetable plants. On the downside, the copper infused lumber does not stand up as well as the arsenic infused lumber when it is contact with the ground, it will typically last about 5 to 10 years, depending on climate, before it starts to deteriorate. Just FYI.
I liked that you filmed every step, explaining what you have done. This was the best that I have seen on building a garden bed. Great for me as a beginner.
Ty soo much for sharing. I am considering in expanding my small patio & backyard garden. I am considering raise beds because of the benefits but didn't know how to water them efficiently. TY, soooooo much for the step by step.
Two questions (actually kinda 4 questions lol) (I'll also look at other videos for answers too though) 1.) Can this sort of drip system hook up to rain barrels? How would the set up for that part look like if so? 2.) Can I build my own drip system from supplies found at regular hardware stores? If so, what are recommended pieces and material types?
I was trying to figure out how to do that! I use airstones and want to make compost tea. Im looking to find how i can pump a bin of water into a garden bed. Any ideas?
I was thinking about rain barrels also. The water faucet is too far away to connect directly. For my present garden beds, I have to pull a long hose over to water them. A rain barrel setup (or just filling up the barrels from the faucet) would be ideal.
@@musenenlightened1984 if you have an existing system like the one in this video, add a T to the line to add your barrel in then you can use a cheap water pump to move your nutrient solution. Depending on the volume of your tubing it wouldn't take much of a pump.
If interested in a fairly inexpensive raised bed, consider using cedar fence slats. They are only 1" (or 5/8) thick but $2.97 per board at Lowe's; (Wood Fencing 1" x 6" x 6' Cedar Fence Board). They also make 1" x 6" x 8', boards as well. I made a 3' x 6' bed in 2016 (it's 2020 now) using these boards and they are still in great shape. I made bed 3 slats high, (17.4") high since boards aren't really 6" wide. I also made the legs 4 inches longer than bottom of box and planted those 4 inches below ground for bed stability. When time comes to change out a board, it should be as easy as unscrewing and replacing. Cost of slats and 1- 4"x4" about $35.00. I added pvc pipe on inside of box for hoops so that added to cost a bit but still done for under $60.00. If you have untreated scrap 2 x 4's laying around, join them with screws and use for the legs. Repurpose what you can.
I used pressure treated wood for two 4x8 raised beds this year and havn't had any issues at all yet. However i did line the inside with plastic before adding my soil mixture...
Great video. Just wanted to add, that if you live in a hot country (like where I am, Australia) or assuming Texas/Cali. Do not whatever you do leave the lines above the surface, always have them below ground as much as possible. Even here in Victoria, one of our 40 degree days the water in the pipe can easily hit 50-60, and even a short burst of that before the cool water is enough to kill plants. Done that way too many times than I care to admit.
GREAT video Tim !! 👍🤠 I'm just starting to put a garden together and your advice is priceless and is going to be put to use in my garden project in the next few days and weeks !! 👍😉 I have retired and looking forward to seeing my garden grow and enjoy the benefits of being able to grow ones own veggies!! GREAT advice for us you tube people learning gardening!! 👍🤠 Cheers from Ron Tasmania Australia!! 😉👍🍅🍉🍎🍋🍐🍏🌱🍇🍓🍒🍍🌽🍄🥕🥝🥒🥑🥗🍄🥕🌰
All wood will rot eventually but if you avoid contact with the soil it helps. Therefore I put the corners on some stones so they are lifted off the earth if only an inch. Additionally I protect the inside with the plastic bags the compost came in
Plastic allows BPA's in your soil epically during the summer growing months. We all have to except the fact that our raised beds have a limited life span.
Do you think you could do a video on how you set up the hoop house on top of your raised beds? Look like a great design. I think it would be super helpful. Thank you.
Thank you very much. Straight forward and very easy to follow. We started gardening about fice few years ago and it gets more rewarding every year.. Wanted to build some more raised beds and you just inspired me. Take care
Maybe I missed it, but I don't think you mentioned dealing with freeze in your permanent water installation. Underground irrigation systems are usually blown out in the Fall using high capacity air compressors, something few homeowners have. Leaving water in the lines over the winter is likely to result in damage. I have a very similar setup on my multiple raised gardens to what is shown in this video, and I also use Dripworks as my supplier for the drip irrigation system. But I lay my main line tubing on the grass and tack it down using "U" shaped gardening staples, so I can easily pull them up in the Fall, drain them, and store them in the rafters of my garage over the Winter. I do not use the nailed hose clamps to anchor the mainlines along the top of the wood, but rather run the raised mainline tubing on top of the soil, along side the wood; it nestles in there very nicely; sometimes a staple or two into the dirt is needed. To help with seasonal assembly and disassembly, I don't use the mainline tubing between each raised garden if they are separated by more than a couple feet. Instead, I add the Dripworks fitting that adapts from the mainline tubing to garden hose fittings, then use garden hose to run water out from the source to the gardens. I tend to run one garden hose to each 'region' where I have one or two raised gardens, with a multi-zone timer controlling each garden hose, so I can have better control of which garden is watered when. Again, I use the "U" shaped gardening staples (Dripworks sells these as well) to hold the garden hose down to the ground, and after the first week or two, it just settles down and the grass grows over it, and it is practically invisible, and not a trip hazard, and I can mow over it without any issues. It still pulls up easily in the Fall.
Check my video here on how I do this. How to Winterize Drip Irrigation Fall Winter Raised Bed Gardening - Raised Bed Drip Irrigation ruclips.net/video/m0j8XT74Hik/видео.html I blow the lines out with an air compressor, I use this specially designed attachment amzn.to/2Vicvg5 (As an Amazon Associate I earn from qualifying purchases from Amazon Links)
Hey Tim! I noticed you don't have a discussion portion on your youtube channel, which is where I'd otherwise leave this comment. First off, love this video! I've shared it with a few friends and family members. The production value, information, and your role on camera have all been top notch. What's your itinerary for releasing more videos? One a week or? A tour of your garden could be a great video! Also, if one were to use treated wood to avoid rot, would using a tarp between the wood and the raised bed be a good idea? Thanks for the great work and looking forward to more videos!
Hi 1rcanada - Appreciate the wonderful words - I have a large backlog of video ideas and scripts, I'm going to be working on those as soon as I can, to get more helpful videos out. If you can't find rot resistant natural wood (e.g. cedar), it may be an option to enclose the bed with thin 1inch/2.54cm cedar fencing. It's inexpensive and will add a barrier of protection. For a way to support you can use our custom garden planning tool! For a small fee you can generate a custom garden schedule, layout and detailed grow guides! 🪴PLAN YOUR GARDEN IN MINUTES WITH OUR CUSTOM PLANNING TOOL ⏰ → bit.ly/3DZe3NR
Thanks for the very detailed explanation on this drip irrigation system. I've spent *months* searching for RUclips content creators in CT with no luck. I mistakenly clicked on your video as I was scrolling through my recommended list, and had no idea your channel even existed until 15 minutes ago. I'm heavily considering creating an organic market garden and/or organic backyard garden in CT. You unknowingly (or, maybe intentionally?) showed the map as you searched for organic compost near you, and as soon as you did, you earned yourself a subscriber. Now, if you'll excuse me... I'm about to lose my day of tweaking my business plan to binge watch your channel. You'll catch lots more of me in the comments, and I might find a way to contact you in the near future. Thanks again!
Thanks so much for the wonderful comment. Good luck in your endeavor! Fee free to sent me a note at organicbackyardgardening@gmail.com and I can send over a few resources that may be helpful in your project.
Nice work on the garden beds. Mine only lasted about 5 years before rotting out, so I need to re-do them this year with cedar. Expensive, but it is a very nice look. I have read that the pressure treated wood with copper is okay for garden beds. I think it is called MicroPro Sienna. However, I think cedar is the best option. I will make the new raised beds taller and add a top board which will act as a seat or a bench - a nice look!
You are correct. On December 31, 2003, the U.S. wood treatment industry stopped treating residential lumber with arsenic and chromium (chromated copper arsenate, or CCA). However people continue to spread false information across the internet that it is unsafe...
This is what I came here to say... The disgust around pressure treated wood is absurd. Its the "Hip" thing to do to "highly suggest against pressure treated wood" when pressure treated wood is now safe for organic gardens. If you're REALLY worried about it, do what I do and use a pond liner as an insulator between the wood and your soil. I do it more to protect the wood against constant moisture from the soil and make it last longer, however..
Yes! Check my video here on how I do this. How to Winterize Drip Irrigation Fall Winter Raised Bed Gardening - Raised Bed Drip Irrigation ruclips.net/video/m0j8XT74Hik/видео.html I also use this special attachment amzn.to/2Vicvg5 (amazon affiliate link)
Your video has given me the courage to go ahead and install my drip irrigation kit. I’ve had it for 4 years now, and have been afraid to install it. I feel like I can do it now. I think I noticed that you didn’t use the 1 inch drip hose that already has the pre-punched drip holes. I have a different brand kit, but it looks like your kit. It has the same parts. I still ordered 2 extra 1/4 inch irrigation hoses and extra parts to use with it. Just to be sure I had enough since it didn’t cost much. I plan to use it for my raised garden beds and my pots on the patio. But, I might move the pots off the patio and onto the grass. I have a lot of pots and grow bags. I’ll figure it out. Thank you for sharing.
So glad this video gave you the courage - Yes I did use the line that had pre punched drip holes (emitters). Please visit the Organic Backyard Gardening website at www.organicbackyardgardening.com for more helpful growing guides and upcoming gardening planning services organicbackyardgardening.com/PlanMyGarden. Don’t forget to please ring the bell (next to subscribe) to get immediate real-time video notifications of new videos!
Check my video here on how I do this. How to Winterize Drip Irrigation Fall Winter Raised Bed Gardening - Raised Bed Drip Irrigation ruclips.net/video/m0j8XT74Hik/видео.html I blow the lines out with an air compressor, I use this specially designed attachment amzn.to/3IbssJ0 (amazon affiliate link)
I like your set up. My yard cascade downward and I've been looking for a video like this... Thank you, Oh, and for showing how to set up the drip system!
You know what would be a great video? Not the installation of drip irrigation but best uses of drip: where to place, how long to run, whatever else... I’ve seen a bunch of videos on installations but little on just the simple use of them. If anyone can direct me to that... have at it.
Hi Tim, I loved the video, thank you! My question is, can I hook this system up to my existing sprinkler system for the lawn? If so, do I need any extra parts (pressure regulator, extra connectors, etc?). For me, that would be the best solution, but I am just unsure how to connect it to the sprinkler system. Thank you in advance!
Yes you can! There are many different retrofit kits (like this - affiliate link) - amzn.to/3PnCHy0 You might also like my free weekly email tips bit.ly/FreeWeeklyGardeningTips
I’m wondering about winter and potential freezing of the buried irrigation lines. Is this something I should be concerned about? Thanks for the great video!
Yes! You should blow them out. Check my video here on how I do this. How to Winterize Drip Irrigation Fall Winter Raised Bed Gardening - Raised Bed Drip Irrigation ruclips.net/video/m0j8XT74Hik/видео.html I blow the lines out with an air compressor, I use this specially designed attachment amzn.to/3IbssJ0 (amazon affiliate link). You also might be interested in my free weekly gardening tips! bit.ly/FreeWeeklyGardeningTips
Interesting idea... Your plan is simpler, cheaper and faster to build. Would your plan lead to uneven watering? I know next to nothing about drip irrigation systems. But it just seems like the water pressure in the line would degrade after each drip hole and that pressure drop would accumulate with each drip hole and might become significant at some point??? At what point is the key question because we just wanna water the plants efficiently! Your idea seems kinda like a Series circuit in electricity, whereas the design in the video is more like a Parallel circuit.
Good video for those not familiar with yard irrigation. Why did you bury the lines? Why not just clamp them to the box sides for easier maintenance and less work?
Thanks bob! Good question, I grow grass so mow/weed wack in between the beds so having them under ground makes it a bit easier and I don’t have to worry about anyone tripping. If I had mulch pathways this would be a good option!
I followed a similar plan on my raised beds but would caution that these emitter lines are prone to clogging over time (especially if you have hard water in your area) and will need to be replaced accordingly. Depending on the mineral content of your water supply, they may need to be replaced every year or may last two or three years before certain lines clog and stop working altogether. I wish they made a "No Clog" version of these types of lines but have not been able to source them.
Thanks so much for the feedback! In those new beds this year I have.l strawberries, squash, potatoes, garlic, broccoli, basil, tomatoes, cucumbers and ornamental gourds :)
Absolutely brilliant video! Very well explained with excellent information. As a raised bed gardener for years, I can attest to the veracity of all the information in this video. Great job and many thanks!
Thanks Josie, glad you liked it! Please visit the Organic Backyard Gardening website at www.organicbackyardgardening.com for more helpful growing guides and upcoming gardening planning services organicbackyardgardening.com/PlanMyGarden. Don’t forget to please ring the bell (next to subscribe) to get immediate real-time video notifications of new videos!
I’d suggest not running the tube along the top of the board in the event you want to put hoops up or sit along the edge as you harvest or weed. I’d also suggest running the pipe up the inside of the bed rather than the outside if you use a mower or weed eater/wicker along your beds so you don’t break the pipe.
This is such a great simple to understand video. I do need help with how I will connect my main water to the beds. My faucet is at least 60 ft from my beds. Any suggestions? Thank you.
Hi Caprice, you could use a simple garden hose to take the water from your faucet to beds, at the end of the season you could roll it up. This would be the easiest. :) Cheers, Tim
This was a very informative video. I appreciate your referral of DripWorks and mention of their resources as I want to learn how to tap into an existing yards system for my raised bed gardens. Thank you! V
Hi there, thanks for the information. Maybe u have already answered it but do u remember how much the material cost? Just ballpark. Seems like with all the fittings they add up rather quickly. 😺 I read that CPVC does well outdoors and may look into that for comparison.
I would say for one 4x8 bed, with drip irrigation - about $100 for material - just a ballpark. Buying an online kit that is cedar will cost probably double.
I blow the lines out with an air compressor, I use this specially designed attachment amzn.to/2Vicvg5 I will be making a video on this shortly as I’ve had a lot of questions about it! :)
@@OrganicBackyardGardening Thanks! This was the same thing I was going to ask. It looked like you probably live in CT, so I figured you had to have a way.
See this link to the dripworks raised bed kit, you’ll notice the filter that attached correctly to the outdoor faucet, then attach the low pressure adapter then the Easy Loc Female Hose Start which attached to the main line. www.dripworks.com/garden-bed-irrigation-kit-medium?ref=lfw3jygn
Thanks so much for sharing your knowledge. Your an awesome RUclipsr. This in go will help a lot when we move onto our homestead in three months. Very excited. God Bless you.
How would I shut off and drain the system before winter sets in, please? Also, can all the lines stay put in winter? Do they need to be protected or buried deeper in Nova Scotia? Many thanks for your great video!
Hey Judy! 👋 Yes, you can keep your drip irrigation lines intact over the winter if you blow them out. 💨 Check out my video here 📹 on how to winterize them: ruclips.net/video/m0j8XT74Hik/видео.html To blow out the lines, I use an air compressor with this special attachment 🔧 that you can find on Amazon: amzn.to/3IbssJ0 (affiliate link). Also, if you're into gardening, make sure to sign up for my free weekly gardening tips! 🌱🌻🌿 bit.ly/FreeWeeklyGardeningTips Happy gardening! 🌞🍅🥕🍓
Hello-this video is exactly what I needed to have the confidence to install my own drip irrigation...thank you for that. It looks like it’s been just over a year since you did this. How has the system held up through the seasons? Do you like it? Is there anything you would do differently?
Hi Jennifer! It’s has held up great. I have the same set up installed on several other beds not shown on the video for many years and it works great. No issues! Just make sure to blow the lines out at the end of the year if you have freezing weather and bring in the emitters in the winter to prolong the life. Good luck!
I'm curious if there's any reason not to bring the supply tube directly up into the raised bed (under the raised bed frame)? I'm about to put in a system for 3 raised beds in a row , with buried supply line and would love to avoid the tubing mounted on the outside... would love comments... thanks!
I've been using above ground beds for about 15 years. One thing that helps: paint the boards, ESPECIALLY the exposed grain ends, and BEFORE assembly so you get coverage at the joints. They look nicer, and I think you get about double the life. Irrigation: I use a dual-level system. I drill a 3/4 hole in the box side, about 1/3 from the bottom. I run 5/8 main (valve at the entrance to the box if you want to isolate) into the box, tee to each side, elbows along each side (all this 1/3 from bottom). I then connect 1/4 drip tube (integral weep holes) alternating in stripes from the two sides, covering the layer; again, 1/3 from bottom. In each corner I put an above ground 90 degree sprayer, adjustable, with a spray range long enough to cover the size of the bed. When first planting, I use both the above ground sprayers, and the lower (future root) matrix is always active. After the plants have rooted, I turn off the above ground sprayers, leaving only the below ground root system with water. This reduces evaporation, and also discourages surface weeds.
I just built my first dripper system and after I finished I had the idea that I should have set up a similar below ground watering system. Might be back out there on Saturday undoing all of my work.
Good luck! Join My Insiders List for Free Weekly Garden Tips
bit.ly/FreeWeeklyGardeningTips
You should post a video, I’d be interested!
@@shelshele Gee a video is sooo not-my-generation! :-) Since a year ago, I figured even easier method: the 5/8 (standard plastic irrigation pipe) carries enough water that you can run it down the middle, and serve ALL the 1/4 tubes from one main pipe. Again, put in about 1/3 soil depth, and put the underground dripper grid on top of that soil (then fill the rest). Install the 1/4" laterals about every 6~12", and cut them so the drip holes are staggered, alternatingly. Remember that this lower grid isn't meant to give 100% coverage to seeds/seedlings: it just has to wet the soil "down there", and the roots will grow to the moisture.
@@petem6503 Are the underground dripper's specifically for in-soil applications? Don't they just get blocked over time?
One thing I have found helpful when doing drip irrigation in cold temperatures is to use a propane torch with a push button ignitor to slightly heat (be careful not to burn) the ends of the tubing a few seconds before pressing the tubing on the fittings. This works well on the harder poly tubing as well as the 1/4" drip line. I have installed hundreds of feet of drip in my orchard this way in the winter and makes life a lot easier especially when using barbed fittings instead of compression fittings.
Hi Kent - this is a wonderful tip - the plastic can really be hard to work with. Cheers, Tim
Yes, the "new" pressure treated wood is safe for use for raised garden frames... with a few precautions! Up until 2003, the most common preservative used for pressure treated wood was chromated copper arsenate (CCA), a compound using arsenic as its primary rot protectant.The compounds currently being used are alkaline copper quat (ACQ) and copper azole (CA-B). Both contain copper and a fungicide but no arsenic.Yes, New Pressure treated wood is safe.
Thanks! Saved me from freaking out. I just built one with pressure treated pine. But i also plastic lined the walls. Hopefully there was nothing wrong with that :D
Me too 😅
To be on the safe side, a little common sense would go a long way, just use regular wood
Copper is extremely toxic to the body and causes a whole host of issues. Check out The Medical Medium to learn how toxic and problematic copper deposits in the body can be.
This was a wonderful video. Thank you! Wanted to add, pressure treated wood has come a long way in the past years. You can now buy garden safe pressure treated wood that will last you for up to 10 years and costs quite a bit less that douglas fir (and certainly much cheaper than cedar). I have about 300 sq ft of raised garden bed using pressure treated pine, and I come out with about 500-600 pounds of fresh, healthy produce every year. Just check the labelling to ensure the treatment process is such that it is certified as a Environmentally Preferable Product (EPP).
where did you purchase this wood you talk about?
@@warfarewar8206 I don't believe that the old arsenic treated wood can be sold in recent years. Now it's all copper based as another commenter stated and shouldn't be an issue.
@@svenulfskjaldbjorn5401 Interesting, I stand corrected.
Wayne Mahon j
That seems like a crazy good amount of food for 500-600 sq ft, could you tell us more such as, what you grow, in what region, and your soil/amendment used
Newer pressure treated wood is actually quite safe to use in the garden! Of course, some people may not feel comfortable with any treated products but MCA, CA-B, and ACQ do not contain arsenic, which was the main concern with earlier types of treated wood such as CCA. They do contain copper, but the amount that would be required for toxicity is far higher than what is typically seen with plants grown in these beds.
Un-treated wood is still preferable, but for people who may have issues with rot and pests newer treated products offer a good alternative.
And thanks for the video! Looking to make one of these this coming season and install drip irrigation in my other raised beds.
Benjamin Dan good treatment to the timbers then builders Dpc wrapped all round in and out well and correctly then nice free skip timbers ie pallets to clad the out side of the beds for a nice natural look . never replace timbers and lasts 30 years if you don’t clad the face 👍 I like doing it once and well 😊
Lance Uppercut I’m not up on some of the terms. Can you explain this in laymen’s terms please?
Agreed. Newer pressure treating is fine for building beds. Also, gravity does this thing where it pulls stuff down for the most part. So...?
What do you mean never? When did they switched over?
Another fellow CT resident who likes your videos. This video is exactly what I was looking for. Thanks for showing multiple examples and explaining everything.
Hi Michael, thanks so much for the note. I am really glad this has helped! Tim
Thanks for the video. I have used pressure treated lumber for my raised beds since the feds banned the arsenic infused lumber about 7 years ago. Pressure treated lumber today uses copper to deter rot and works very well for raised beds. The infused copper has an additional benefit, it kills garden fungus just like the copper fungicide that is sprayed on vegetable plants. On the downside, the copper infused lumber does not stand up as well as the arsenic infused lumber when it is contact with the ground, it will typically last about 5 to 10 years, depending on climate, before it starts to deteriorate. Just FYI.
Deals on wheels
I liked that you filmed every step, explaining what you have done. This was the best that I have seen on building a garden bed. Great for me as a beginner.
So glad I was able to help you!
I noticed this is from 4 years ago, but a good clear video on irritation. Thank you.
Bed and irrigation is still working perfect! Thanks for watching!
Best tutorial I’ve found so far! Thank you for an easy to understand guide AND explaining how to find the right resources.
Randi, Glad it has helped! Happy Growing!
Ty soo much for sharing. I am considering in expanding my small patio & backyard garden. I am considering raise beds because of the benefits but didn't know how to water them efficiently. TY, soooooo much for the step by step.
Kelly! No problem, glad it helped! Good luck with your expansion! Cheers, Tim
Excellent video. Clear and concise. Really appreciated your explanation on installing the drip line.
This is the best tutorial for drip irrigation
Thanks Lunar, glad I could help!
Many thanks for your video. It gave me good ideas on how to install my first raised bed for tomatoes. Regards from Peru-Chile.
Glad it was helpful!
2020 goals 🌱👩🏭
This guide was really clear, packed with helpful info from start to finish.
Glad it was helpful!
Thank you so much. I noticed I did my drip irrigation all wrong. I'll watch a few more times so I can correct it. You're wonderful.
Glad I could help Ava!
Two questions (actually kinda 4 questions lol) (I'll also look at other videos for answers too though)
1.) Can this sort of drip system hook up to rain barrels? How would the set up for that part look like if so?
2.) Can I build my own drip system from supplies found at regular hardware stores? If so, what are recommended pieces and material types?
Thank you so much!!!!! I love the drip works website and cannot wait to place an order for my garden beds. Amazing! YES!!!!
You are so welcome!
Great video . One hint put cutoff valve on top of bed and cover supply pipe with 1 inch PVC cut in half in case you have to use a weed trimer
Best video on the subject I have seen.
That is great. Thank you for the video. Any suggestion to protect the woods against pests and water damage?
Excellently explained everything
Glad it was helpful!
You could definitely have a few rain barrels to help with feeding gravity wise. Nice setup though and it looks real solid!
I was trying to figure out how to do that! I use airstones and want to make compost tea. Im looking to find how i can pump a bin of water into a garden bed. Any ideas?
I was thinking about rain barrels also. The water faucet is too far away to connect directly. For my present garden beds, I have to pull a long hose over to water them. A rain barrel setup (or just filling up the barrels from the faucet) would be ideal.
@@Shadow.Dragon PRECISELY!! Sounds like my issue!lol
Thanks positive feedback!
@@musenenlightened1984 if you have an existing system like the one in this video, add a T to the line to add your barrel in then you can use a cheap water pump to move your nutrient solution. Depending on the volume of your tubing it wouldn't take much of a pump.
Great video mate. Very well edited and clear voice over. Subbed
It appears you live in my region. I'm in Stonington. Enjoying this very much!!!!
Very cool!
If interested in a fairly inexpensive raised bed, consider using cedar fence slats. They are only 1" (or 5/8) thick but $2.97 per board at Lowe's; (Wood Fencing 1" x 6" x 6' Cedar Fence Board). They also make 1" x 6" x 8', boards as well. I made a 3' x 6' bed in 2016 (it's 2020 now) using these boards and they are still in great shape. I made bed 3 slats high, (17.4") high since boards aren't really 6" wide. I also made the legs 4 inches longer than bottom of box and planted those 4 inches below ground for bed stability. When time comes to change out a board, it should be as easy as unscrewing and replacing. Cost of slats and 1- 4"x4" about $35.00. I added pvc pipe on inside of box for hoops so that added to cost a bit but still done for under $60.00. If you have untreated scrap 2 x 4's laying around, join them with screws and use for the legs. Repurpose what you can.
I used pressure treated wood for two 4x8 raised beds this year and havn't had any issues at all yet. However i did line the inside with plastic before adding my soil mixture...
Nice work Pythagorus
I cannot wait to build my raised garden beds thank you for making it easy for me . I am upstate New York and will use the places you recommended.
Good luck!
Great video. Just wanted to add, that if you live in a hot country (like where I am, Australia) or assuming Texas/Cali. Do not whatever you do leave the lines above the surface, always have them below ground as much as possible. Even here in Victoria, one of our 40 degree days the water in the pipe can easily hit 50-60, and even a short burst of that before the cool water is enough to kill plants.
Done that way too many times than I care to admit.
Wow! Very helpful tip! Thank you for sharing Matthew!
Looks easy
Thanks So , easy to learning because of your video 👍💪
Glad to hear that!
I am looking forward to Installing these on my raised beds. Thank you for making this video!
Hi Levi! Glad it helped. Happy growing!
oh my gosh, you made everything sooo much easier for me; thank you!!
You're so welcome!
wow! seriously this video is so well done. I loved it
Thanks so much Matt! Happy Growing!
New copper pressure treated are ok. U shud always predrill so the wood doesnt split when using screws
GREAT video Tim !! 👍🤠 I'm just starting to put a garden together and your advice is priceless and is going to be put to use in my garden project in the next few days and weeks !! 👍😉 I have retired and looking forward to seeing my garden grow and enjoy the benefits of being able to grow ones own veggies!! GREAT advice for us you tube people learning gardening!! 👍🤠 Cheers from Ron Tasmania Australia!! 😉👍🍅🍉🍎🍋🍐🍏🌱🍇🍓🍒🍍🌽🍄🥕🥝🥒🥑🥗🍄🥕🌰
Nice job.
thank you for helping me see i can actually do this my self
So glad it helped!
This is awesome. Thank you! Planning on making some raised beds shortly and was looking into a better watering method!
Thanks for stopping by! Good luck!
All wood will rot eventually but if you avoid contact with the soil it helps. Therefore I put the corners on some stones so they are lifted off the earth if only an inch. Additionally I protect the inside with the plastic bags the compost came in
Plastic allows BPA's in your soil epically during the summer growing months. We all have to except the fact that our raised beds have a limited life span.
Do you think you could do a video on how you set up the hoop house on top of your raised beds? Look like a great design. I think it would be super helpful. Thank you.
Thx bro enjoyed your vid im looking in using this technique on my own beds thx again
Hi Stuart! Glad I could help - good luck!
Great straight forward video. Enjoyed. We want to add a raised garden to the farm this year. To date, have only had livestock.
Thank you very much. Straight forward and very easy to follow.
We started gardening about fice few years ago and it gets more rewarding every year.. Wanted to build some more raised beds and you just inspired me.
Take care
Maybe I missed it, but I don't think you mentioned dealing with freeze in your permanent water installation. Underground irrigation systems are usually blown out in the Fall using high capacity air compressors, something few homeowners have. Leaving water in the lines over the winter is likely to result in damage.
I have a very similar setup on my multiple raised gardens to what is shown in this video, and I also use Dripworks as my supplier for the drip irrigation system. But I lay my main line tubing on the grass and tack it down using "U" shaped gardening staples, so I can easily pull them up in the Fall, drain them, and store them in the rafters of my garage over the Winter. I do not use the nailed hose clamps to anchor the mainlines along the top of the wood, but rather run the raised mainline tubing on top of the soil, along side the wood; it nestles in there very nicely; sometimes a staple or two into the dirt is needed.
To help with seasonal assembly and disassembly, I don't use the mainline tubing between each raised garden if they are separated by more than a couple feet. Instead, I add the Dripworks fitting that adapts from the mainline tubing to garden hose fittings, then use garden hose to run water out from the source to the gardens. I tend to run one garden hose to each 'region' where I have one or two raised gardens, with a multi-zone timer controlling each garden hose, so I can have better control of which garden is watered when. Again, I use the "U" shaped gardening staples (Dripworks sells these as well) to hold the garden hose down to the ground, and after the first week or two, it just settles down and the grass grows over it, and it is practically invisible, and not a trip hazard, and I can mow over it without any issues. It still pulls up easily in the Fall.
Check my video here on how I do this. How to Winterize Drip Irrigation Fall Winter Raised Bed Gardening - Raised Bed Drip Irrigation ruclips.net/video/m0j8XT74Hik/видео.html
I blow the lines out with an air compressor, I use this specially designed attachment amzn.to/2Vicvg5 (As an Amazon Associate I earn from qualifying purchases from Amazon Links)
Hey Tim! I noticed you don't have a discussion portion on your youtube channel, which is where I'd otherwise leave this comment. First off, love this video! I've shared it with a few friends and family members. The production value, information, and your role on camera have all been top notch.
What's your itinerary for releasing more videos? One a week or? A tour of your garden could be a great video!
Also, if one were to use treated wood to avoid rot, would using a tarp between the wood and the raised bed be a good idea?
Thanks for the great work and looking forward to more videos!
Hi 1rcanada - Appreciate the wonderful words - I have a large backlog of video ideas and scripts, I'm going to be working on those as soon as I can, to get more helpful videos out. If you can't find rot resistant natural wood (e.g. cedar), it may be an option to enclose the bed with thin 1inch/2.54cm cedar fencing. It's inexpensive and will add a barrier of protection.
For a way to support you can use our custom garden planning tool! For a small fee you can generate a custom garden schedule, layout and detailed grow guides!
🪴PLAN YOUR GARDEN IN MINUTES WITH OUR CUSTOM PLANNING TOOL ⏰
→ bit.ly/3DZe3NR
Thanks for the very detailed explanation on this drip irrigation system. I've spent *months* searching for RUclips content creators in CT with no luck. I mistakenly clicked on your video as I was scrolling through my recommended list, and had no idea your channel even existed until 15 minutes ago.
I'm heavily considering creating an organic market garden and/or organic backyard garden in CT. You unknowingly (or, maybe intentionally?) showed the map as you searched for organic compost near you, and as soon as you did, you earned yourself a subscriber.
Now, if you'll excuse me... I'm about to lose my day of tweaking my business plan to binge watch your channel. You'll catch lots more of me in the comments, and I might find a way to contact you in the near future. Thanks again!
Thanks so much for the wonderful comment. Good luck in your endeavor! Fee free to sent me a note at organicbackyardgardening@gmail.com and I can send over a few resources that may be helpful in your project.
From a fellow Connecticut-ian, thanks for the info. Will also use this in my new hot-box. :)
Nice work on the garden beds. Mine only lasted about 5 years before rotting out, so I need to re-do them this year with cedar. Expensive, but it is a very nice look. I have read that the pressure treated wood with copper is okay for garden beds. I think it is called MicroPro Sienna. However, I think cedar is the best option. I will make the new raised beds taller and add a top board which will act as a seat or a bench - a nice look!
You are correct. On December 31, 2003, the U.S. wood treatment industry stopped treating residential lumber with arsenic and chromium (chromated copper arsenate, or CCA). However people continue to spread false information across the internet that it is unsafe...
This is what I came here to say... The disgust around pressure treated wood is absurd. Its the "Hip" thing to do to "highly suggest against pressure treated wood" when pressure treated wood is now safe for organic gardens. If you're REALLY worried about it, do what I do and use a pond liner as an insulator between the wood and your soil. I do it more to protect the wood against constant moisture from the soil and make it last longer, however..
Not sure if anyone had asked but how do you winterize the line? Thank You
Angelus420 was looking for the same question. Maybe commenting here will help catch attention.
Look at his reply to Mona S.
Yes! Check my video here on how I do this. How to Winterize Drip Irrigation Fall Winter Raised Bed Gardening - Raised Bed Drip Irrigation ruclips.net/video/m0j8XT74Hik/видео.html I also use this special attachment amzn.to/2Vicvg5 (amazon affiliate link)
Nice. Just getting ready to install my drip so this was beneficial.
Great to hear!
nice video...I'm learnin everyday...
Glad to hear it
Thank you! This has to be the least complicated system!
Your video has given me the courage to go ahead and install my drip irrigation kit. I’ve had it for 4 years now, and have been afraid to install it. I feel like I can do it now. I think I noticed that you didn’t use the 1 inch drip hose that already has the pre-punched drip holes.
I have a different brand kit, but it looks like your kit. It has the same parts. I still ordered 2 extra 1/4 inch irrigation hoses and extra parts to use with it. Just to be sure I had enough since it didn’t cost much. I plan to use it for my raised garden beds and my pots on the patio.
But, I might move the pots off the patio and onto the grass. I have a lot of pots and grow bags. I’ll figure it out.
Thank you for sharing.
So glad this video gave you the courage - Yes I did use the line that had pre punched drip holes (emitters).
Please visit the Organic Backyard Gardening website at www.organicbackyardgardening.com for more helpful growing guides and upcoming gardening planning services organicbackyardgardening.com/PlanMyGarden. Don’t forget to please ring the bell (next to subscribe) to get immediate real-time video notifications of new videos!
Thanks for the video and all the information.
What can I do to avoid freezing of the main and the drip line in winter?
Check my video here on how I do this. How to Winterize Drip Irrigation Fall Winter Raised Bed Gardening - Raised Bed Drip Irrigation ruclips.net/video/m0j8XT74Hik/видео.html
I blow the lines out with an air compressor, I use this specially designed attachment amzn.to/3IbssJ0 (amazon affiliate link)
Thanks!
What a awesome and more importantly simple system to set up!! I’m a bit worried about winter though..
Thanks for your help and your time
Much appreciated
Thank you!
I like your set up. My yard cascade downward and I've been looking for a video like this... Thank you, Oh, and for showing how to set up the drip system!
Thanks for the feedback! Glad it helped! Yes for the cascading beds remember you only need to level out the perimeter. :)
You know what would be a great video?
Not the installation of drip irrigation but best uses of drip: where to place, how long to run, whatever else...
I’ve seen a bunch of videos on installations but little on just the simple use of them. If anyone can direct me to that... have at it.
Hi Tim, I loved the video, thank you! My question is, can I hook this system up to my existing sprinkler system for the lawn? If so, do I need any extra parts (pressure regulator, extra connectors, etc?). For me, that would be the best solution, but I am just unsure how to connect it to the sprinkler system. Thank you in advance!
Yes you can! There are many different retrofit kits (like this - affiliate link) - amzn.to/3PnCHy0
You might also like my free weekly email tips bit.ly/FreeWeeklyGardeningTips
Like all the info , and how you show how to Google search it also !
Thanks for the feedback!
I’m wondering about winter and potential freezing of the buried irrigation lines. Is this something I should be concerned about?
Thanks for the great video!
Yes! You should blow them out. Check my video here on how I do this. How to Winterize Drip Irrigation Fall Winter Raised Bed Gardening - Raised Bed Drip Irrigation ruclips.net/video/m0j8XT74Hik/видео.html
I blow the lines out with an air compressor, I use this specially designed attachment amzn.to/3IbssJ0 (amazon affiliate link). You also might be interested in my free weekly gardening tips! bit.ly/FreeWeeklyGardeningTips
Great video dude! Thanks for putting it together
for snuffing out the grass, i prefer using cardboard material. it degrades quickly and helps leave the existing soil life in place.
love love this video... i gained so much confidence i'm going to try this come spring
Awsome! Keep us posted on the progress and let me know if you have any questions!!!
You could just loop the drip line back and forth and save on all the fittings and some 1/2” tubing.
Interesting idea... Your plan is simpler, cheaper and faster to build. Would your plan lead to uneven watering? I know next to nothing about drip irrigation systems. But it just seems like the water pressure in the line would degrade after each drip hole and that pressure drop would accumulate with each drip hole and might become significant at some point??? At what point is the key question because we just wanna water the plants efficiently! Your idea seems kinda like a Series circuit in electricity, whereas the design in the video is more like a Parallel circuit.
Yes, you could certainly do this!
Good video for those not familiar with yard irrigation. Why did you bury the lines? Why not just clamp them to the box sides for easier maintenance and less work?
Thanks bob! Good question, I grow grass so mow/weed wack in between the beds so having them under ground makes it a bit easier and I don’t have to worry about anyone tripping. If I had mulch pathways this would be a good option!
I followed a similar plan on my raised beds but would caution that these emitter lines are prone to clogging over time (especially if you have hard water in your area) and will need to be replaced accordingly. Depending on the mineral content of your water supply, they may need to be replaced every year or may last two or three years before certain lines clog and stop working altogether. I wish they made a "No Clog" version of these types of lines but have not been able to source them.
Great Tip!
Excellent video!. It motivates me to get ready to begin the project.
Thank you! Glad you found it helpful!
Great video. Is there a reason why you wouldn't put the main irrigation line on the inside of the bed before you put the bed on? Just wondered?
You could certainly do that!
High quality video. With lots if good info. Keep up the good work
Thanks Kyle!
Wow! You make this look so easy.
good pace with relaxing music
clear and concise instructions
How many vegetables did you grow?
Thanks so much for the feedback! In those new beds this year I have.l strawberries, squash, potatoes, garlic, broccoli, basil, tomatoes, cucumbers and ornamental gourds :)
@@OrganicBackyardGardening Thank you for sharing 🙏🏽❤
Thank you! Your video was helpful!
Hi Jamie, glad I could help!
Absolutely brilliant video! Very well explained with excellent information. As a raised bed gardener for years, I can attest to the veracity of all the information in this video. Great job and many thanks!
Thanks so much Thom!
Using galvanized screws can leach as well
Thank you for this!
My pleasure!
How neat! Loved your video.
Thanks Josie, glad you liked it!
Please visit the Organic Backyard Gardening website at www.organicbackyardgardening.com for more helpful growing guides and upcoming gardening planning services organicbackyardgardening.com/PlanMyGarden. Don’t forget to please ring the bell (next to subscribe) to get immediate real-time video notifications of new videos!
I’d suggest not running the tube along the top of the board in the event you want to put hoops up or sit along the edge as you harvest or weed. I’d also suggest running the pipe up the inside of the bed rather than the outside if you use a mower or weed eater/wicker along your beds so you don’t break the pipe.
Great Video. I will be doing this very soon! Thank You!
Good luck and thanks for stopping by!
Great video, complete
This is such a great simple to understand video.
I do need help with how I will connect my main water to the beds. My faucet is at least 60 ft from my beds. Any suggestions? Thank you.
Hi Caprice, you could use a simple garden hose to take the water from your faucet to beds, at the end of the season you could roll it up. This would be the easiest. :) Cheers,
Tim
@@OrganicBackyardGardening thank you kindly!
This was a very informative video. I appreciate your referral of DripWorks and mention of their resources as I want to learn how to tap into an existing yards system for my raised bed gardens. Thank you! V
Victoria, thanks for stopping by! So glad it was helpful! Happy growing! - Tim
thank you for your video is very good and i really will be used your video for my raised beds .
Hi Sandra, excellent! I’m glad it could help!
Hi there, thanks for the information. Maybe u have already answered it but do u remember how much the material cost? Just ballpark. Seems like with all the fittings they add up rather quickly. 😺
I read that CPVC does well outdoors and may look into that for comparison.
I would say for one 4x8 bed, with drip irrigation - about $100 for material - just a ballpark. Buying an online kit that is cedar will cost probably double.
Can you show us how you winterize the system?
I blow the lines out with an air compressor, I use this specially designed attachment amzn.to/2Vicvg5 I will be making a video on this shortly as I’ve had a lot of questions about it! :)
@@OrganicBackyardGardening Thanks! This was the same thing I was going to ask. It looked like you probably live in CT, so I figured you had to have a way.
I have the video just need to edit it! Will be out in a couple weeks!
How do you connect water to the system? Do you connect a garden hose and just turn it on like you would do with a sprinkler?
See this link to the dripworks raised bed kit, you’ll notice the filter that attached correctly to the outdoor faucet, then attach the low pressure adapter then the Easy Loc Female Hose Start which attached to the main line. www.dripworks.com/garden-bed-irrigation-kit-medium?ref=lfw3jygn
Nicely done and very organized !
Thank you! Cheers!
Thanks so much for sharing your knowledge. Your an awesome RUclipsr. This in go will help a lot when we move onto our homestead in three months. Very excited. God Bless you.
Pressure treated lumber has not contained harmful chemicals for many years.
Still not sanctioned for organic growing.
yes. yes. YES. Love it SO muhhh
Very helpful
Thanks so much for sharing. I've learned a lot. Pammie from Chicago IL
Thanks for watching!
How would I shut off and drain the system before winter sets in, please? Also, can all the lines stay put in winter? Do they need to be protected or buried deeper in Nova Scotia? Many thanks for your great video!
Hey Judy! 👋 Yes, you can keep your drip irrigation lines intact over the winter if you blow them out. 💨 Check out my video here 📹 on how to winterize them: ruclips.net/video/m0j8XT74Hik/видео.html
To blow out the lines, I use an air compressor with this special attachment 🔧 that you can find on Amazon: amzn.to/3IbssJ0 (affiliate link).
Also, if you're into gardening, make sure to sign up for my free weekly gardening tips! 🌱🌻🌿 bit.ly/FreeWeeklyGardeningTips
Happy gardening! 🌞🍅🥕🍓
Great job!
Thank you! Cheers!
Hello-this video is exactly what I needed to have the confidence to install my own drip irrigation...thank you for that. It looks like it’s been just over a year since you did this. How has the system held up through the seasons? Do you like it? Is there anything you would do differently?
Hi Jennifer! It’s has held up great. I have the same set up installed on several other beds not shown on the video for many years and it works great. No issues! Just make sure to blow the lines out at the end of the year if you have freezing weather and bring in the emitters in the winter to prolong the life. Good luck!
I'm curious if there's any reason not to bring the supply tube directly up into the raised bed (under the raised bed frame)? I'm about to put in a system for 3 raised beds in a row , with buried supply line and would love to avoid the tubing mounted on the outside... would love comments... thanks!
That’s a great idea, it would look much cleaner with that approach!
I had this same question. 😉 I'm glad I found it and the guy answered. Hooray.
How did that work for you? The only thing I could've think of is you wouldn't have access to the shut off valve.