Hope you enjoyed!!! Make sure to like and subscribe!!! *********Disclaimer********* This is a older video so info may be a bit off! Go easy on me lol! Check out the newer videos here! ruclips.net/p/PLQiOg6Lr31OL6evrjsewgpU2eDsfJSWw0
@@rome0dome I would definitely take it out and plug it with a self tapping screw. You don’t want that rod to become a projectile in the motor and cause catastrophic damage
So i took out my Governor Gear and the Sway Arm that hangs from the top a while ago and when i did i left that pin that the Governor Gear sits on and spins on in the block just so it could keep the hole plugged cause i figured it was already the perfect size to plug the hole. But was never quite sure if i should have pulled that pin out and replaced it with a bolt of not. Cause i've seen other youtubers pull that governor gear pin out and put a bolt in it's place. Now finally i see you left the pin in there too so i don't feel like i did it wrong i guess lol. I guess i was never sure if that pin would wiggle loose from the vibration of riding and fall out into the engine but so far it hasn't. You think it's fine and safe to leave the governor gear pin in the block the way it is ?
Yeah! If you want you can just hammer the pin out and put a bolt in its place but I left mine in and it’s oil tight and hasn’t came lose and trust me my bike is now a fully built motor and vibrates like hell and it hasn’t came lose lmaoooo
The bypass and the delete are different the bypass will still have that gear reduction because the camshaft will spin it causing it to do the slowing effect but a delete will make you faster then the bypass because there is no gear causing the slowing effect.
Hope you enjoyed!!! Make sure to like and subscribe!!! *********Disclaimer*********
This is a older video so info may be a bit off! Go easy on me lol! Check out the newer videos here! ruclips.net/p/PLQiOg6Lr31OL6evrjsewgpU2eDsfJSWw0
Congrats on the massive hands bro.
I needed this
I didn’t cut the arm or take off the rod. But what should I put in the whole the arm use to be in?
@@rome0dome I would definitely take it out and plug it with a self tapping screw. You don’t want that rod to become a projectile in the motor and cause catastrophic damage
Good information thanks.
What size bolt will fit on the top?
@@MikeBeatzcom 1/4" bolt with a 10mm hex head with self tapping threads
@@Guido19I didn't tap the side one… will that do anything wrong? I didn't have that Omb warehouse flywheel puller.
@@MikeBeatzcom no I let the shaft in mine I never tapped it and it’s fine!
You forgot to take out the black washer behind where the governor gear sits internally
@@NastyNyjj I took it out I didn’t film it it was stuck to the gear itself
So i took out my Governor Gear and the Sway Arm that hangs from the top a while ago and when i did i left that pin that the Governor Gear sits on and spins on in the block just so it could keep the hole plugged cause i figured it was already the perfect size to plug the hole. But was never quite sure if i should have pulled that pin out and replaced it with a bolt of not. Cause i've seen other youtubers pull that governor gear pin out and put a bolt in it's place. Now finally i see you left the pin in there too so i don't feel like i did it wrong i guess lol. I guess i was never sure if that pin would wiggle loose from the vibration of riding and fall out into the engine but so far it hasn't. You think it's fine and safe to leave the governor gear pin in the block the way it is ?
Yeah! If you want you can just hammer the pin out and put a bolt in its place but I left mine in and it’s oil tight and hasn’t came lose and trust me my bike is now a fully built motor and vibrates like hell and it hasn’t came lose lmaoooo
the goat
The bypass and the delete are different the bypass will still have that gear reduction because the camshaft will spin it causing it to do the slowing effect but a delete will make you faster then the bypass because there is no gear causing the slowing effect.
Yeah. Originally I had it bypassed but I removed it cause I’m putting in the stage 4 kit and also for that reason.
@@Guido19Good!