Thanks for this video, I am about to get my first scorpion esc ever so i needed to learn how to program everything.. I plan to use the usb cord and not the adaptor cause getting it used with a heli and i'm sure he doesn't have the adapter.
Look, I first set up the ESC SCORPION through the application (limited) in V-Bar Control, now I am setting up through the computer in the SPROTO application. Will there be no crash with synchronous settings? What do you think ? 🤔
On my Tribunus2 120 I can't change the drive frequency and timing?. The motor & caps on esc are to hot to touch after 1min on the ground with no blades?? Also motor makes a high pitch noise around mid stick. Spent nearly a $1000 on scorpion products for my G570 and I can't even use it without cooking everything.
Hello. I purchased a Tribunus 14-300A Series engine governor. I cannot pair with V-Bar Neo (V-Bar Control). I also want to connect via telemetry wire ... I still do not understand which socket in the figure is "MASTER", which is "AUXILIARY" ??? There are 9 pieces of pin connections .. Help me please🙏🙏🙏
Hi. I am using GOVERNOR ESC SCORPION. Is it possible that on the ground there are some rotor revolutions, and others in the air? (They are respectively lower)
If you use a 5000mAh pack, and let's say you want to have 20% left in the pack. This would give you 4000mAh of usable capacity. Take 4000mAh ÷ 1000 to get the value in Ah. Which would equal to 4.0Ah
@@PoomUdi Thanks. Help me ... I have 80% gas shelf. When I took off for the first time, the helicopter did not rise for a long time, and only when the throttle stick was in the extreme upper position, the helicopter took off. When I raised the helicopter again, everything was fine, the throttle stick was just above the middle. Although I did not change the gas shelf, I left 80%. Do you think this ESC is configurable?
@@PoomUdi Please tell me, when changing the GAIN parameters (soft, middle and hard), how is the helicopter controlled? What does this affect? How does it feel when flying a helicopter? Yes, I want to say that now I am adjusting the flight ✈️ of the LOGO 800 helicopter, like the flight of a copy helicopter, I do not fly 3D. Looking forward to your reply, thank you 🙏 in advance.
Thanks for this video, I am about to get my first scorpion esc ever so i needed to learn how to program everything.. I plan to use the usb cord and not the adaptor cause getting it used with a heli and i'm sure he doesn't have the adapter.
Usb chord is fine!!
HELLO. PLEASE TELL ME WHAT SETTINGS YOU HAVE SET TO SORT THE ROTOR TO SPIN SO SLOWLY?
Look, I first set up the ESC SCORPION through the application (limited) in V-Bar Control, now I am setting up through the computer in the SPROTO application. Will there be no crash with synchronous settings? What do you think ? 🤔
On my Tribunus2 120 I can't change the drive frequency and timing?. The motor & caps on esc are to hot to touch after 1min on the ground with no blades?? Also motor makes a high pitch noise around mid stick. Spent nearly a $1000 on scorpion products for my G570 and I can't even use it without cooking everything.
After loading from a file, my Sproto program hung and now I do not see ESC SCORPION. Help if you know?
Make sure yoy have proper drivers installed
Hello. I purchased a Tribunus 14-300A Series engine governor. I cannot pair with V-Bar Neo (V-Bar Control). I also want to connect via telemetry wire ...
I still do not understand which socket in the figure is "MASTER", which is "AUXILIARY" ??? There are 9 pieces of pin connections ..
Help me please🙏🙏🙏
Master is for your throttle signal from the Rx and Auxilary is for rpm sensor.
Hi. I am using GOVERNOR ESC SCORPION. Is it possible that on the ground there are some rotor revolutions, and others in the air? (They are respectively lower)
Lower rpm in the air? Due to your rotor disc being loaded up, normal.
@@PoomUdi thanks 🙏
Could you please explain how to calculate the value for "max battery power"?
If you use a 5000mAh pack, and let's say you want to have 20% left in the pack. This would give you 4000mAh of usable capacity. Take 4000mAh ÷ 1000 to get the value in Ah. Which would equal to 4.0Ah
Hi. What kind of governor do you use? ESC scorpion or vbar governor?
I use Scorpion internal govener eventhough I fly on the Vbar. Just my personal preference.
@@PoomUdi Thanks. Help me ... I have 80% gas shelf. When I took off for the first time, the helicopter did not rise for a long time, and only when the throttle stick was in the extreme upper position, the helicopter took off. When I raised the helicopter again, everything was fine, the throttle stick was just above the middle. Although I did not change the gas shelf, I left 80%. Do you think this ESC is configurable?
@@very9000 Try a recalibration
@@PoomUdi Please tell me, when changing the GAIN parameters (soft, middle and hard), how is the helicopter controlled? What does this affect? How does it feel when flying a helicopter? Yes, I want to say that now I am adjusting the flight ✈️ of the LOGO 800 helicopter, like the flight of a copy helicopter, I do not fly 3D. Looking forward to your reply, thank you 🙏 in advance.
@@PoomUdi Thanks. If all is well now, do I need to re-calibrate or not?
Neo vbar control, goes to vbar pid or external gov if i want to use vbar governor? Thanks
Select Vbar PID for Vbar use, you can check out the scorpion website on how to DIY a telemetry cable as well.
poomysan got it got mine working now, but i notice when i hit my motor idle it does something really different,
on the trottle curve , normal why not a straight 65 % curve and use trottle hold for 0
TheRagge1 , in case I forget and flick hold off when the heli is in an unsafe position... just a habit for me.
@@PoomUdi Just don't forget to switch out of that flight mode before going inverted.