Snap Fastener Installation Tool Demo
HTML-код
- Опубликовано: 10 сен 2024
- Purchase the Snap Fastener Installation Tool here: www.sailrite.co...
Snap Fastener Installation Tool is a small, two piece setting tool for snap fasteners. The metal anvil has two sides, one for setting buttons and the other for eyelets. This tool can also be used without the base for setting rivets. Great for setting nickel-plated brass snaps and Common Sense button-back screw studs. Not recommended for use with stainless steel fasteners.
Use of a 1/8″ hole punch is recommended to create a hole in the fabric for the snap barrel before setting. An awl may also be used in lighter fabrics to force an opening in the fabric weave for the snap barrel.
Thank you for showing how to install the snaps! I bought a package of Sontax brand snaps at the home improvement store. The instructions on the package were not clear. Your video helped me to understand how the pieces fit together. Your guidance ensured a successful repair.
I'm glad the video was helpful for you!
Ms.Gratz!!! Thank you, thank you, thank you! I have a daycare and all of the bibs that I've purchased in the past have velcro. The cost for the snap button bibs, compared to the velcro is ridiculous! So after 18 years of being in this business, I just thought of putting on snap buttons myself. This video will help me tremendously! Thank you for doing this video. I really appreciate it!
You are welcome!!!
I was just looking at my snap kit that I bought from Amazon, and no, I’ve never used it. But I checked it out and I was right. But I watched your video twice, just to make sure. Thank you for your time.
Glad it was helpful!
Thank you!! I purchased the snaps, but couldn't find instructions on how to use them. They may have gotten lost. Thank you for the Video!!
I can tell from the narrators voice..you can take his word these are good button snaps.
🤣
Very nice 😅 2:21
watch out Thor ! When I put snaps on thicker leather I have to make the holes a little bigger so the snap sits flush and seats well. I use a tapered tool that stretches the leather just enough to allow that then the leather gets tight again when the snap is set. Rocket Science !
I have an item that contains metal snaps, and I'd like to find the correct, matching snaps that go with it. How does one go about doing that?
Hey, thanks! Managed to make a nice knife case for a friend with a brass snap contrasting with the dark leather. Looks great!
Please tell me you guys sell a kit. I dont want to spend the next hour trying to figure out all the items I need to put in my shopping cart.
Cool video but I will say , she needs a bigger mallet if there is one in this universe.
There is only one hammer larger, and THOR is using it... lol
cajunsk
Lighthammer
😂😂😂😂
Watching this after the fact that I put alot of fasteners together on a jacket! Pretty strong fasteners!
This was great thanks for this video it helped fix my Columbia pants where the snaps broke. Used this video and like new.
thank you! i appreciate it! it is amazing how many things i could have fixed or saved!
Thanks for the demo, its a big help and much appreciated.
Can you combine the male and female snaps together like reversible? I'm trying to fix my mss sleeping bag.
I am sorry, I do not understand the question. Can you email me a photo of what you are trying to do? eric@sailrite.com
I have this exact same little kit. So I should not confuse this with rivets and rivet installation?
I can't get the first one, only the second part
What can be done if the post will not sit any tighter against the socket? I am using the same tool kit (from General) for the same nickel plated snaps. I keep hammering but the post will not curl down flat enough for the snap to work.
What is the length of the button's barrel, is it 11/64", 1/4" or 5/16" (just give me the Sailrite item number, if that easier for you)? Then how many layers of fabric are you installing the snap into? Finally which snap installation tool are you using from Sailrite?
It would be better if they showed the parts more. Her hands cover up too much.
Can one apply this same principle to making a hole in wood?
En donde consigo la herramientas para poner esos broches
Could nonmetallic snap button
I was given this link to for instructions to install the snap set I bought, these are nothing (kinda) like what I bought. Umm er. So after lots of trial and miss I got the snaps to work. BTW, these are not the cheapest.
Is there anyone that used this a couple of times and still come back to the video ?
That’s me.
Always have to come back to figure out which is which.
😄
What difference between nickel plated and stainless, which the nickel is necessary?
Nickel plated brass or Stainless Steel which should you use? Both work well and are approved by Sailrite for marine use, even in saltwater conditions. However Stainless Steel is slightly more corrosion resistant than nickel plated brass and Stainless Steel is a stronger metal, so it is often considered a slightly better snap.. With that said most of the OEM boats use nickel plated brass over stainless steel snaps. Why? They are cheaper and easier to install than the SS.
@@SailriteDIY Thank you, I had the same question
Do you sell a snap system for leather work?
Where you buy that tool
Screw the setters, I want that mallet. Looks like it came right out of the forge of Hephaestus.
You can purchase that mallet here: www.sailrite.com/Mallet-Hammer-Style-3
Just cracked the fuck up at this
Im With 86: What's that?
My kit came without the Anvil, so guess it's usless unless I can figure out another way to use it without...Thanks...
You must have the anvil or it will not work. If it was purchased from Sailrite please contact us with your order number and we will resolve that issue.
@@SailriteDIY Thanks but it wasn't Sailrite, got it on Amazon from company called Seloky...appreciate it though, I've ordered a set from a different company with just the tools...Thanks again...
Great demonstration. Thanks!
Why not stainless steel?
The choice is yours. Nickle Plated Brass or Stainless Steel Snaps. Stainless Steel is the best choice, but nickle plated brass is still a good choice.
I love you…..lol 😜🤣 you made this so much easier for me thank you!
Um....I how can I get the snaps to attach with just a hammer....
Well you need a snap fastener installation tool and a hammer. Then they can be installed.
SANGAT MEMBANTU. TAPI SAYA TIDAK TAU DIMANA MEMBELI ALAT UNTUK MEMASANG KANCINGNYA 😫
Show as the used whith steel please
This will fit on 10mm thickness?
If you use a snap with a barrel length of 5/16 inch it will accommodate thicknesses of up to: From 11/64" to 1/4"
Great 👍 working
Thanks for this! I’m stairing at my kit and tool and was like don’t bother hit up RUclips.
thank you!
Thank you!!
Thank you.
great video...my snaps are in place but when i hit them (sockets) with a hammer with the tools they seem to split....
If the snap barrel splits it usually means they are a cheaply made snap. Sailrite only offers the best quality snaps from DOT, the barrels of the Sailrite snaps do not split.
duh !
you need a bigger mallet
Very nice
Know that I have this info, I'm attaching the tops of cowboy boot to my crocs
holy crap lady your mallet puts Thor`s hammer to shame..
Merci !
Cool video...
i live downstairs."knock it off!" lol kidding.... thank you.
PLEASE SLOW DOWN AND IDENTIFY EACH PIECE SEPARETLY. I AM A BEGINNER SO I KEPT GETTING LOST.
I NEED that tool,!!
You can purchase it here: www.sailrite.com/Snap-Fastener-Installation-Tool
Gracias
Fixed my wallet. Thank you. :)
I want that hammer, gotta get one !!!
You can get that mallet here: www.sailrite.com/Mallet-Hammer-Style-3
Why can't this dude pronounce the "L" in Sail.
ممتاز ممتاز👌🏻
NOT CLEAR! You need to do a close up! AVOID these fools!
Thumbs down, Hammer not big enough
Thank u so much
U R SEW VELCOM.
🥰🥰🥰
awesome
Useless demo as no proper time to identify sequence of part assembly
She thinks she’s Thor lol
Thor and Thor LOL
Good for leather belts too 🙂
Lot of thank
Thank You
thank you!
You are welcome!