@@goplayfull my work is done for today but i had some prblm after installation it work as like a charm but when reboot it didnt try it on pppwn again simply i change power connection to usb its fixed well just share for the others !
Is the solder point layout the same for the phat ps4 models, or do these points only relate to the slim/pro version of the console? About to attempt on this installation on a CUH-1001A model of the console. I know the available votltage map image on the net is that of the slim variant (B-SAD-003), so im not going to be able rely on it. Also wanted to know if i caught that last bit correctly, that we should tap into the usb +5v line for vbus in order to allow the chip to "reboot" itself on console reboots.
im new to ps4 mods. can you make a tutorial if you havent on how to install games and run a dashboardif you can. i know about xbox 360 modding but not ps4. ty
you just need to reconnect the USB Type-C cable to the Luck Fox to perform the reflash. So, yes, you need to open the PS4 case without removing the cable that is already soldered.
Hello everyone! I have a problem, the first chip was programmed and installed on the 2016 model fv 11.00 everything worked from the first in 20 minutes. The other two consoles 2116 and 2216 with other exactly the same chips will not work, everything works as it should pppwn owned then it happens that the notification Payload no script found comes out! Tried with several different chips the same settings the same programmed and connected but the same thing happens. Then I took out the chip from 2016 which works flawlessly and golden loads in about 20 seconds, and put some of these chips that did not work on 2116 and on 2216 and it works normally, everything finishes to the end and then again when it turns off and starts does golden load in 20-30 seconds? I took it apart a few times and checked if the wires were soldered properly and if the layout was correct, but everything is ok, every time I re-do it almost to the end and it says Payload script not found. I put the same chip that worked great in 2016 in 2216 and it also says Payload script not found! All PS4 is 11.00 Does anyone have any ideas or suggestions as to what the hell is going on!s to what the hell is going on! Thnx in advance!
@@goplayfull Thanks, I'll try with ipv6 and see what hapen, although I found a solution for this too, I put the payload on the USB flash drive and it pulls it from the USB flash drive
@@goplayfull grateful for your help dude.. I indeed do all those steps.. I setup a LAN connection once I have plugged in the Ethernet cable.. I have also tested the Ethernet cable itself.. I can only imagine that there may be bad soldering somehow?.. anyone else have this issue?.
Try checking if the PS4 is still getting an IP address after the golden payload is active. If it still is, it means Luckfox hasn't shut down. This could be the cause.
So I followed the tutorial to the letter, and installed my Luckfox into the console. I get the PPPwnED notification, but then it says "payload not found" what did I do wrong? Can someone PLEASE help me?!
To activate the GoldHEN payload for the first time, you need to plug in a flash drive containing the "goldhen.bin" file in the root folder. This is only required to be done once. You can download the file here github.com/stooged/PI-Pwn/blob/main/USB%20Drive/goldhen.bin
Just as a heads up, you forgot to mention the credentials when accessing the network share. You did mention it when ssh'ing into the luckfox, but it also asked me for the creds when i attempted to access via the file browser. root:luckfox
As far as I understand, after manually establishing the connection for the first time, the jailbreak process is done automatically when we turn the device off and on again. So, I don’t need to put the device into sleep mode, and if I take the device somewhere else, I won’t have to start the process from scratch. The automatic setup takes place, right? We just need to manually connect once, and then when we power it up via USB, the jailbreak is automatically performed. If this is correct, please confirm. I didn’t fully understand that part.
That's exactly right. The goal of to turn off Luckfox Pico after finishing the jailbreak is to prevent it from staying on all the time since it's no longer needed after the jailbreak is successful. This also helps extend the life of Luckfox, as the lucfoxpico mini can get hot quickly when it's running.
I can’t see Pico Mini in the SocToolKit. I installed the driver reboot the system and then press the boot button while plug in my pc still not shown any idea why ? Thx for help
I got one that will not connect.. I can flash it, see it under networks, change to IP. but after that nothing, \\172.32.0.93 brings up a folder but nothing in it and cant add files to it..
@goplayfull yeah it's weird, tried different ports, tried changing a bunch of network settings, reflashed with web just to test, tried on a different laptop. For some reason this one can't be accessed.. lol.
Try checking the system menu - system information to see if your PS4 is getting an IP address from Lockfox. If not, it’s possible that the PPPWN script isn’t running.
Have you already entered the username and password in the network settings menu, PPPOE, on your PS4? If you have and it still isn’t working, try reinstalling the pppwn script. Make sure the script settings match the firmware version of your PS4.
hanya bisa turun ke versi terakhir kali sebelum di update. jika firwmare sebelumnya 11.50 ya bisanya cm bisa balik ke versi itu, tidak bisa ke versi 11.00 atau 9.00
@@goplayfulli tried the method 2.. where i needed to solder luckfox to the motherboard.. do i need to remove the luckfox and reflash it and do everything from the beginning..or just plugging a pendrive with goldenhen will do the work.. please answer.. I'm stuck with a disassembled ps4 since 2 days..
@@ivan_kulakov I think it might have been my luckfox as it asked for username and password on accessing via ftp at this point 6:19 Seems like my device was previously set up?
Awesome tutorial thanks!
Best video on luckfox pico min b ❤
Thanks. I appreciate it
Simply the best tutorial on this subject ! Thanks a lot.
Did you succeded in downgrading the fw versions please ? (even the latest 12.00)
Yes I did. I already made the video before this one
@@goplayfullhow about the goldhen.bin file?
great video im gonna follow this when i attempt it
Best tutorial out there, thank you!
You're very welcome!
Simple tutorial, good job. 13:35 goldhen.bin file is on the pendrive, which is on the PS4 USB port?
Yes.
Thx will try soon
Your welcome
@@goplayfull my work is done for today
but i had some prblm after installation it work as like a charm but when reboot it didnt try it on pppwn again
simply i change power connection to usb
its fixed well just share for the others !
Is the solder point layout the same for the phat ps4 models, or do these points only relate to the slim/pro version of the console? About to attempt on this installation on a CUH-1001A model of the console. I know the available votltage map image on the net is that of the slim variant (B-SAD-003), so im not going to be able rely on it. Also wanted to know if i caught that last bit correctly, that we should tap into the usb +5v line for vbus in order to allow the chip to "reboot" itself on console reboots.
The Ethernet solder points are the same for all PS4 models. For the VBUS connection, I recommend taking it from the 5V point on the USB port.
Good work. Is there a way to go back from 12 to an older version for ps4 ?
Thank you
By reverting the firmware, you can go back to the version you had before the firmware update.
im new to ps4 mods. can you make a tutorial if you havent on how to install games and run a dashboardif you can. i know about xbox 360 modding but not ps4. ty
Yeah it's great, but what happens when an update comes out next month? Open it again and damage something?
you just need to reconnect the USB Type-C cable to the Luck Fox to perform the reflash. So, yes, you need to open the PS4 case without removing the cable that is already soldered.
wonderfull bro
Thanks
very useful and very neat work inside
keep going bro
Thank's i appreciate it
Hello everyone!
I have a problem, the first chip was programmed and installed on the 2016 model fv 11.00 everything worked from the first in 20 minutes.
The other two consoles 2116 and 2216 with other exactly the same chips will not work, everything works as it should pppwn owned then it happens that the notification Payload no script found comes out!
Tried with several different chips the same settings the same programmed and connected but the same thing happens.
Then I took out the chip from 2016 which works flawlessly and golden loads in about 20 seconds, and put some of these chips that did not work on 2116 and on 2216 and it works normally, everything finishes to the end and then again when it turns off and starts does golden load in 20-30 seconds?
I took it apart a few times and checked if the wires were soldered properly and if the layout was correct, but everything is ok, every time I re-do it almost to the end and it says Payload script not found.
I put the same chip that worked great in 2016 in 2216 and it also says Payload script not found!
All PS4 is 11.00
Does anyone have any ideas or suggestions as to what the hell is going on!s to what the hell is going on!
Thnx in advance!
"Try using the pppwn IPV6 script. Maybe 2216 and 2116 are cursed PS4 models."
@@goplayfull Thanks, I'll try with ipv6 and see what hapen, although I found a solution for this too, I put the payload on the USB flash drive and it pulls it from the USB flash drive
Thank you.. all install perfectly fine and working great however my Ethernet port no longer works? Any ideas why?
The Ethernet port can only be used after the Goldhen payload is active and the Luckfox Pico is shut down.
@@goplayfull even after this the post will not work.. I'm out of ideas..
U need You need to reset the internet settings on the PS4 to default, as we previously set it to use PPPOE.
@@goplayfull grateful for your help dude.. I indeed do all those steps.. I setup a LAN connection once I have plugged in the Ethernet cable.. I have also tested the Ethernet cable itself.. I can only imagine that there may be bad soldering somehow?.. anyone else have this issue?.
Try checking if the PS4 is still getting an IP address after the golden payload is active. If it still is, it means Luckfox hasn't shut down. This could be the cause.
So I followed the tutorial to the letter, and installed my Luckfox into the console. I get the PPPwnED notification, but then it says "payload not found" what did I do wrong?
Can someone PLEASE help me?!
To activate the GoldHEN payload for the first time, you need to plug in a flash drive containing the "goldhen.bin" file in the root folder. This is only required to be done once.
You can download the file here
github.com/stooged/PI-Pwn/blob/main/USB%20Drive/goldhen.bin
What gauge wire did you use for the internal mod? (Stranded or solid core wire?)
I'm using an old PS2 controller cable. You can use any cable as long as it fits the hole in the metal plate
@@goplayfull Oh ok, thank you for the reply!
Just as a heads up, you forgot to mention the credentials when accessing the network share. You did mention it when ssh'ing into the luckfox, but it also asked me for the creds when i attempted to access via the file browser.
root:luckfox
Yep, big error this one.
As far as I understand, after manually establishing the connection for the first time, the jailbreak process is done automatically when we turn the device off and on again. So, I don’t need to put the device into sleep mode, and if I take the device somewhere else, I won’t have to start the process from scratch. The automatic setup takes place, right? We just need to manually connect once, and then when we power it up via USB, the jailbreak is automatically performed. If this is correct, please confirm. I didn’t fully understand that part.
That's exactly right. The goal of to turn off Luckfox Pico after finishing the jailbreak is to prevent it from staying on all the time since it's no longer needed after the jailbreak is successful. This also helps extend the life of Luckfox, as the lucfoxpico mini can get hot quickly when it's running.
@@goplayfull Thanks for your answer. Great work, great video.
I can’t see Pico Mini in the SocToolKit. I installed the driver reboot the system and then press the boot button while plug in my pc still not shown any idea why ? Thx for help
Try plugging it into a different USB port, changing the USB cable, or testing it on another laptop/computer.
@@goplayfull i got it flashed and soldered all fine. thx for your tutorial tumbs up
I got one that will not connect.. I can flash it, see it under networks, change to IP. but after that nothing, \\172.32.0.93 brings up a folder but nothing in it and cant add files to it..
Try to re connect the USB Cable
@goplayfull yeah it's weird, tried different ports, tried changing a bunch of network settings, reflashed with web just to test, tried on a different laptop. For some reason this one can't be accessed.. lol.
So we only need a switch for power to cut off from the direct source of power automatically 😂
hi will this work ps4 Fw 12.00 thanks
It still cannot work on PS4 with firmware above 11.00
why not showing lukfoxed instead of pppw i think the video is not the same
Its new script.
My modchip is flashing inside the ps4 however no sign of injection I have flashed it where have I gone wrong
Try checking the system menu - system information to see if your PS4 is getting an IP address from Lockfox. If not, it’s possible that the PPPWN script isn’t running.
Ok it’s not getting an up address what should I do now?
Have you already entered the username and password in the network settings menu, PPPOE, on your PS4? If you have and it still isn’t working, try reinstalling the pppwn script. Make sure the script settings match the firmware version of your PS4.
Im on firmware 8.0 any suggestions on which is best firmware to jailbreak? Thanks
9.00
recently i brought PS4 FW 8.03 then i upgraded to 9.00 the golden FW, please do the same and everything will be super easy for you to keep enjoying
Thanks for the replies. So what's the difference than software jailbreaking vs the Luckfox pico jailbreaking
9.00 is much more stable, and you only need a flash drive for the jailbreak process. It's different from the one that uses the Luckfox Pico.
9.60 ?
Bg lu org indo? Bisa emg nurunin fw 12 ke 11 atau 9?
hanya bisa turun ke versi terakhir kali sebelum di update. jika firwmare sebelumnya 11.50 ya bisanya cm bisa balik ke versi itu, tidak bisa ke versi 11.00 atau 9.00
should i jailbreak the 10.01 or update to 11 im not too sure whats better or more stable
If you can play normally on version 10.x, it's better not to update because PPPWn is the same stability across all firmware versions.
@@goplayfull so i should jailbreak the firmware im on rn im ofw 10.01
@@DrModz0 hacking script is the same, you just need correct payload for your fw version
Is ps4 11.0 version available?
Yes
payload not found????? please help..
For the first jailbreak u need to plug pen driver to USB port contain file goldhen payload. Name it goldhen.bin
@@goplayfull i didn't know that.. thank you so much.. let me try this..
@@goplayfulli tried the method 2.. where i needed to solder luckfox to the motherboard.. do i need to remove the luckfox and reflash it and do everything from the beginning..or just plugging a pendrive with goldenhen will do the work.. please answer.. I'm stuck with a disassembled ps4 since 2 days..
No need to re-flash and no need to use a pen drive either, as it has been done before.
@@goplayfull then what should i do now, ? how can i make this work.. I'm stuck at payload not found
Ini akal plays kh. Kok sama persis video nya?
Channel kedua om
@@goplayfull ouhsmoga go internasional bang. Sy kaget aja ad nyuri video mu
Akalplays
Why the ai voice, so annoying.
It would be even more annoying if I used my real voice.
172.32.0.93
Login: root
Password: luckfox
Port: 22
Thanks, I’m not sure why this wasn’t mentioned in the video?
@@TheCroupier74 New version
@@ivan_kulakov I think it might have been my luckfox as it asked for username and password on accessing via ftp at this point 6:19
Seems like my device was previously set up?
@@TheCroupier74 Luckfox files updated