Oil pump Husqvarna 372XP, 562XP crank bearings and other chainsaws to repair

Поделиться
HTML-код
  • Опубликовано: 25 окт 2024
  • Showing how to fit and test chain bar oil pump on Husqvarna 372XP #chainsaw
    Preliminary info on rebuild of Husqvarna 562XP that needs new crank shaft bearings.
    A load of other chainsaws to repair.
    #ChainSaw #Husqvarna

Комментарии • 71

  • @mikehobbs7421
    @mikehobbs7421 3 года назад +1

    I literally just ordered a new pump and piece for my 372xp. Came across your vid and it’s by far the best one I’ve seen! Cheers from Canada eh 🇨🇦🍻👍

  • @christopherknee5756
    @christopherknee5756 3 года назад

    This kind of video will get you many more views on RUclips, IMHO. I am certain there are always many people looking for specific information on a certain model of chainsaw. I think the key to a good video is an accurate title and edited to be about 4 or 5 minutes. Seeing how you get parts off and back on the chainsaw is very very helpful. It is the kind of information that a manual (if you can ever find the manual for your one-off freaking saw!) cannot provide. There is no substitute for experience and that's what you have.

    • @AuMechanic
      @AuMechanic  3 года назад

      Thanks for the comment. I agree with that but the issue is you can never tell how much YT will recommend the video in searches and that largely determines how many views any one video, the content of the video however can determine how much of the videos people watch. In the case of this one it did not do well at first indicating ir did not get recommended but over the year it accumulated more views so that may have been due to viewers watching more of the video that then in turn gets it listed more over the longer term.

    • @Sensei948
      @Sensei948 2 года назад

      @@AuMechanic Friend, how best to position the L nozzle on the carburetor?

  • @shug831
    @shug831 5 лет назад +2

    Love it. It may be fixing neglect but it need done. I've fixed a few for my friends and I can't believe how daft people can be with chainsaws.

    • @AuMechanic
      @AuMechanic  5 лет назад

      Doesn't take much to get them back to working order.
      Thank's for the comment.

  • @keith73z28
    @keith73z28 5 лет назад +1

    I am ready to assemble my 394xp that i bought 24 yrs back. Would love to see you service that 395xp as they are very similar. New sub here in the US. Good videos - thx
    (new piston/cylinder, carb rebuilt and new fuel lines and seals.)

    • @AuMechanic
      @AuMechanic  5 лет назад +1

      Ill be doing a vid on the rebuild of the 562XP crank.
      Aside from that saws are not my main game so videos on them may be few and far between unless I get more which is possible.

  • @anestisrealanime7361
    @anestisrealanime7361 5 лет назад

    Very nice and easy resolution of your video helped me a lot. ..

    • @AuMechanic
      @AuMechanic  5 лет назад +1

      Glad you found it helpfull

  • @kennethmaas6473
    @kennethmaas6473 4 года назад

    Hi like your channel. Kenny from texas.

  • @elroysteele4949
    @elroysteele4949 5 лет назад +1

    Great work on the explanations of how things work from USA, California. Keep up the great Videos.

  • @Aussielife.
    @Aussielife. 4 года назад +1

    Hi mate, how much end float should there be on the clutch drum? My clutch drum can move out and in from the oiler to the c clip about 2-3mm chewed up the plastic oiler arms and now upgrading to the steel one? Great vid btw

    • @AuMechanic
      @AuMechanic  4 года назад +1

      Not sure but that sounds a a bit excessive.
      Ill see if there is a spec.

  • @Rolingmetal
    @Rolingmetal 5 лет назад +1

    I wouldn't mind having one of those small Husqvarna's. You can use it single handedly, and they are great for thinning out tree branches.

  • @brzivoz4323
    @brzivoz4323 5 лет назад +1

    hello, if i put bigger carb (now is 24mm to 28mm or bigger) Would you get more power just with that?
    HONDA MTX 125R Do I need changes regarding ports and exhaust ? bore x stroke ( 56x50.6)

    • @AuMechanic
      @AuMechanic  5 лет назад +1

      Unless the bike has a carb that is a bit small to begin with then its not likely you will get more power simply upsizing the carb alone.
      In fact being a dirt bike you could loose a bit of power at the low end as a bigger carb will not work as well at lower RPM so there is a risk just putting a bigger carb on will have a downside.
      The only reason I would do it is if you were going to do porting and put a higher performance cam in it and maybe increase compression, in short if you are doing engine mods that might mean the stock carb will limit peak power at the top end of the RPM range.

  • @keith73z28
    @keith73z28 5 лет назад +1

    Hey guys; check out this guys youtube page. Freakin cool man. This guy is an advanced engine mechanic- looks like engineer level stuff. Stuff on Holley carbs, and on and on.

  • @josephhutchings3571
    @josephhutchings3571 3 года назад

    Hi AuMechanic could you please tell me before you replaced the oil pump there is a bushing sleeve with metal washer on crank, well between that and crank sea
    is there a rubber washer or is it just the metal bush sleeve. any help from anyone would be great as i took oil pump out and sleeve then blew out with air comp and didn't check thanks.

    • @AuMechanic
      @AuMechanic  3 года назад

      Don't recall but from the look of it in the manual there is an O-ring under the sleeve, part number 503 26 30-19

    • @josephhutchings3571
      @josephhutchings3571 3 года назад

      @@AuMechanic Hi I see now there is a really tiny thin o rubber o ring that goes on shaft just above bearings u can hardly see it then seal goes on high shoulder of bushing pressed on to crank then flat washer ontop of all that for worm gear to turn thanks for your reply and hope this helps for athers needing this solved.

  • @Boston4099
    @Boston4099 4 года назад

    Is that a socket your using to test pump? If so which one?

    • @AuMechanic
      @AuMechanic  4 года назад +1

      Its a socket I made to undo the clutch.

  • @verteup
    @verteup 5 лет назад +1

    You should have way more subs than you do. You sound like a damn engineer. Nice vids.

    • @AuMechanic
      @AuMechanic  5 лет назад

      Thank's for the comment, glad you like the videos.

  • @nickywalsh8492
    @nickywalsh8492 5 лет назад +1

    Hello...👍...fair play to you..I imagine crappy saws are not your thing I may be wrong..u said u worked in repairs previously I can tell...using dogs in vice or spinning crank with drill,,great to see your twist...those ATs are notorious for bearings there high revers,more so if they draw air carb is compensating...they bounce up to 16k with rev boosts as stock...plus 50:1 is lean on oil..they run fine with 40:1..so 👍over all..noticed the long reach socket doctored for clutch tool😉

    • @AuMechanic
      @AuMechanic  5 лет назад +1

      Yeah had a few plug sockets around so converted one into a clutch tool.
      Re the drill, just pushed it against the clutch bell to spin the pump for the test not the whole crank
      Re the crank bearings, IMO the shop was pretty lazy putting a new piston on it and not even so much as turning the crank to see if the bearings felt ok, or washing out the casings, he paid them good money to have the job done.

    • @nickywalsh8492
      @nickywalsh8492 5 лет назад +1

      @@AuMechanic re drill...clever !re shops if I can figure it out or learn how to on RUclips I'll give it a go...

  • @pm270100
    @pm270100 4 года назад

    good vid well done mate where you at vic QLD

    • @AuMechanic
      @AuMechanic  4 года назад

      Cheers Bill
      I'm in Victoria, Melb.

    • @pm270100
      @pm270100 4 года назад

      @@AuMechanic Fern tree gully for me

  • @Gazgit555
    @Gazgit555 5 лет назад +1

    that pump looks like a speedo drive.

    • @AuMechanic
      @AuMechanic  5 лет назад

      Yes it is the same sort of right angle gear setup you would find in motorcycle speed drive.

  • @kennethfraser9006
    @kennethfraser9006 3 года назад

    Put that 335/338 xpt in the bin.

    • @AuMechanic
      @AuMechanic  3 года назад

      Its running ok now and still saws logs so may as well keep it.

  • @Sensei948
    @Sensei948 5 лет назад

    What should be compression in 372xp oem?

    • @AuMechanic
      @AuMechanic  5 лет назад

      Manual has no compression test values but should be at least 150 psi

    • @Sensei948
      @Sensei948 5 лет назад

      @@AuMechanic
      mine has 140 psi? is this a good result?

    • @AuMechanic
      @AuMechanic  5 лет назад

      @@Sensei948 That's about the minimum.
      You need to ensure the throttle is on full / wide open doing a compression test.
      If not have someone give you a hand to hold the gauge while you pull it over at full throttle
      Also make sure the decompression button valve is not leaking.

    • @Sensei948
      @Sensei948 5 лет назад

      @@AuMechanic the test was done correctly. The valve is good. ....

    • @AuMechanic
      @AuMechanic  5 лет назад

      @@Sensei948 Pk good
      So 140 psi is about the minimum you would;want.
      Any idea how many hours it has on it ?
      Maybe pop the muffler off and have a look at the piston up the exhaust port and see if it has any scuff marks on it.