Reinforcing and repairing the Tacoma frame

Поделиться
HTML-код
  • Опубликовано: 13 дек 2024

Комментарии • 144

  • @nwafab5335
    @nwafab5335 2 года назад +20

    Radius corners and avoid vertical welds (zig zags, full radius, or fish mouths are stronger and eliminate stress risers) when welding on and auto chassis, appreciate your video

    • @PostRt
      @PostRt  2 года назад +5

      I appreciate the tips and I have learned a lot just from these video comments. They will be added to the knowledge bank and applied to future projects.

  • @martinsteele345
    @martinsteele345 2 года назад +9

    Really nice work! I feel like I have watched every frame repair video on RUclips. You def show some good work!

    • @PostRt
      @PostRt  2 года назад +1

      Thank you Martin, I appreciate the feedback and kind words. That helps me to keep pushing through and get this truck back on the road.

  • @cmnoyes2
    @cmnoyes2 Год назад +1

    Thank you for documenting and sharing your adventure of repairing your Toyota truck’s frame. I have watched many videos on the repair of rusted frames and glean ideas where possible. I gained several ideas from your videos I had not seen used elsewhere. I especially liked your procedure of fish-plating the inside of the frame rails and using plug welds to add rigidity. Your cleaning of the areas to be welded with acid was a new-to-me process. You mentioned the importance of removing all debris that could be reached inside the frame rails, even beyond the area where you had been welding. Many other videos show frame repair caps added to rotted frames with no internal cleaning attempted. Even if procedures were used to spray anti-rust chemicals into the frames after repairs the spray would only coat the top of the debris pile. That debris will, as you mentioned, continue to adsorb and retain water and road salt and promote degradation of a newly repaired frame. Additionally, the debris could eventually block frame drain holes and further accelerate future frame rot. Folks wanting the most return for their efforts and expenditure would do well to follow your example. Of course, some people may not be able to afford the extra expense of a thorough job and that has to be considered, especially if one is repairing someone else’s vehicle. Thank you again.

    • @PostRt
      @PostRt  Год назад

      You're are very welcome, I'm glad that you found it helpful. I feel the same thoughts as you've explained. Getting the metal stripped clean and sealed up is the best chance it has to last a long time.
      Thanks for watching, and stayed tuned for the final result. It is amazing how far this truck has come!

  • @louisvanrijn3964
    @louisvanrijn3964 11 месяцев назад +3

    Most home builders can weld (think they can). But the penetration depth of the weld is terra incognita for them.
    It is often overseen. The weld lays mostly superficial and that line is nicely polished with the grinder. When you section it, probably half of the steel gauge is connected to the other plate.
    The welding upside down (so the lower welds, where the torch fires upward) are especially sensative for lesser penetration depth.
    Half of the penetration depth is half of the strength. So beware.

    • @PostRt
      @PostRt  11 месяцев назад

      No problemo!
      Getting the material clean was one of the most difficult tasks.

  • @stepho9999
    @stepho9999 5 месяцев назад +1

    Nice to see a repair done correctly

    • @PostRt
      @PostRt  5 месяцев назад +1

      Thank you!
      I feel a whole lot better driving this truck, knowing that the frame is repaired and protected.

  • @DusterNutbar
    @DusterNutbar 10 месяцев назад

    Wow. This is inspiring me to get to work on my old truck!

    • @PostRt
      @PostRt  10 месяцев назад

      Thank you! That is great.
      What truck do you have?

  • @andrewreece3861
    @andrewreece3861 2 года назад

    Nice work! I’m working on repairing an 05 Sequoia frame now. You’re fortunate that you can remove the bed to access the frame. Subscribed

    • @PostRt
      @PostRt  2 года назад

      Absolutely, I am lucky that I can remove the bed for the extra room. Anywhere under the cab though is going to be tricky.
      Good luck with your Sequoia frame Andrew 👍

  • @L4ND.SH4RK
    @L4ND.SH4RK 8 месяцев назад +1

    Ive been dreaming of doing this to my truck. Ive got a couple welders, now... and a tall tank of argon. Just need a plasma cutter and some thick steel.

    • @PostRt
      @PostRt  8 месяцев назад +1

      Sounds like you are on your way to making it happen.
      Good luck with your project 👍

  • @sjb7339
    @sjb7339 2 года назад +3

    When you are welding upside down if you do not have a welding jacket you can use some old hessian backed carpet across your body to catch welding blobs instead of them burning through your clothes and skin and if you don't want heat distortion in your work have an airline with a blow gun to cool the area can also be used to put out small fires keep the good work going

    • @PostRt
      @PostRt  2 года назад +1

      Solid advice. Thanks for the tips!
      I have a fire extinguisher handy for unexpected thermal events but could definitely invest in more PPE now that I am doing more welding.

  • @animal_engineering
    @animal_engineering 2 года назад +1

    Awesome work, my lift often identifies as a paint rack

    • @PostRt
      @PostRt  2 года назад +1

      Hey, you got to do what you got to do 😆
      I have several multicolored ladders from painting projects.

  • @3SM20Pilot
    @3SM20Pilot 2 года назад +2

    Hey buddy! Good to see your channel back up and active. I'd use some weld through primer on panels that you won't be able to access to keep them from rusting again.

    • @PostRt
      @PostRt  2 года назад +2

      Thanks man!
      I wanted to hit it with some weld-through primer but the can I had was so old it gummed up. I do plan to coat the inside of the frame with something like that Eastwood kit.

  • @penningtonmetalworks283
    @penningtonmetalworks283 2 года назад +3

    Looks like solid work. Chasing thin rusty metal to get to good metal always sucks. People often make the mistake of over beefing the repair. It becomes so stiff in that area that thin, weak material breaks somewhere else. I don't repair frames anymore. I replace them. Rust free southern frames blasted and powdercoated. They look great and last a long time. Be sure to spray some type of coating on the inside and open the drain holes in the bottom of the frame!

    • @PostRt
      @PostRt  2 года назад

      Thank you!
      I will most definitely be protecting my work when finished up.
      A rust free and powder coated frame sounds amazing.

    • @jeremyr7147
      @jeremyr7147 2 года назад

      I found the same problem of stress transfer with stronger sections.. & when cutting back: even if it looks solid today, with these thin shit frames, A year later it can be gone.

    • @penningtonmetalworks283
      @penningtonmetalworks283 2 года назад +1

      @@jeremyr7147 I was always very selective of what or if I would repair. If you are trying to limp through for a couple years or wanting it to be forever is the fork in the road. This is why I do replacements only anymore and why I travel south a few times a year for Toyota frames. Start with something good and your results will show. One of those "pay me now or pay me later" senerios.

    • @jeremyr7147
      @jeremyr7147 2 года назад

      @@penningtonmetalworks283 yeah, i just turned down one yesterday, an 03 Avalanche. Told him what were saying here.

    • @penningtonmetalworks283
      @penningtonmetalworks283 2 года назад +1

      @@jeremyr7147 All you had to say was Avalanche lol. No disrespect. Maintenance on any vehicle is huge. To alot of people they are appliances, much like a toaster, a throw away item.

  • @edwinheredia4305
    @edwinheredia4305 Год назад +1

    good work my bro.

  • @davidgentz1731
    @davidgentz1731 Год назад +1

    I love my plasma cutter they're really fun you can do so many cool things with them

    • @PostRt
      @PostRt  Год назад

      Definitely a great tool to have. I'd love to get a CNC Plasma table someday too. They can make some intricate things and with greater precision.

    • @davidgentz1731
      @davidgentz1731 Год назад

      I made a circle cutter gig that looks like a tripod. Just hold the torch handle and turn the steel.

  • @isralelebron7199
    @isralelebron7199 Год назад +2

    Good job. man 👏

  • @projectbumblejeep4190
    @projectbumblejeep4190 2 года назад +1

    For what it's worth, if you have a lift, it's worth the time investment to lift the cab off the frame to get at the repair areas better. Rear cab bolts are a royal pain to remove, but the access you gain to the areas that need to be repaired is worth the time to remove the cab. I ran taps through the cab mounts before dropping the cab back onto the frame, so re mounting the cab was a piece of cake.

    • @PostRt
      @PostRt  2 года назад +1

      Now that the ball is rolling on this project, I may dive deeper into the frame work. Pulling the cab off will likely be in my future as I continue on. Oh how I loathe the rusty fasteners!

    • @TheShillPrince
      @TheShillPrince Год назад

      No need to pull cab 😮 in my opinion and after dozens of frame repairs. Leave cab mounts on but weld temporary legs from cab mount brackets to floor then cut cab mount bracket from frame . The cab is sitting on the floor in exact position in needs to be. Repair frame then reweld cab mount to frame and cut off temporary leg. 😊

  • @jamespenny2798
    @jamespenny2798 2 года назад +2

    This type of work is called "fishplate" repair. The spot welds are a good idea but my opinion would be less holes and larger slotted holes for good penetration. Also stitch welds along top and bottom(40% or so) and no welds on vertical sections. Silicone chalk liberally before undercoating.
    There is whole bunch of more rules for frame extensions. Good job none the less!

    • @PostRt
      @PostRt  2 года назад +1

      A fish plate is a "reinforcement plate" but they are used when joining two structures together. What I did was add a thin plate over the existing frame member that was intact. I do agree with the slotting though. It was easier for me to drill holes than create a series of slots. Many vehicles are welded together using a slotted attaching joint.
      Thanks for the advice!

  • @jasonzelle3571
    @jasonzelle3571 2 года назад +1

    I've got this same project coming up, inside the hollow box it would be best to add some stock that's shaped like snow fence stakes, or stop sign type stock and plug weld it in, then cap it all off with the patterned plates. This inside material will help with torsion factors and everything else. Adds a little weight, but will be bullet proof once it's all tied together. I'm not being negative, I just believe in overkill since your going through the effort.

    • @PostRt
      @PostRt  2 года назад

      It sounds like you have a good plan on how you want to fix up your next project. That would definitely beef things up and I can't say that I have ever seen a frame built that way before. I'm just trying to build my truck a little better than the good Ole factory Toyota spec. Aside from the rusting issues in my region, these are well built and highly reliable vehicles. I don't plan to build this into a rock bouncing offroad machine so it should suffice.

  • @rvmagnum5415
    @rvmagnum5415 2 года назад +1

    Nice , looks great.

    • @PostRt
      @PostRt  2 года назад

      Thank you. The other side is getting finished up soon.

  • @1marcelfilms
    @1marcelfilms Год назад +2

    I would have put zinc spray inbetween the metals and on the inside of the frame. Then finish it with a big spray of fluid film.

    • @PostRt
      @PostRt  Год назад

      You can do it however you would like. I coated all of the metal. Then I used internal frame coating on top of that. When I am all done, I plan to also spray a coating like fluid film on top. Three layers of protection.

  • @markraymond7233
    @markraymond7233 Год назад

    nice job i just finished doing the same area

    • @PostRt
      @PostRt  Год назад

      That's great. How bad was the rust?

  • @Dancing_Alone_wRentals
    @Dancing_Alone_wRentals 2 года назад +2

    3:00 Funny to see the old Toyota frame on the floor.

    • @PostRt
      @PostRt  2 года назад +1

      Out with the old, in with the new.

    • @Dancing_Alone_wRentals
      @Dancing_Alone_wRentals 2 года назад +1

      @@PostRt I wish I had a solution for my Tundra. I've got rust on the passenger's side around the wheel area.
      I'm okay with caulking...not bad with a hot glue gun.....But I don't weld.
      I've been looking for used frames.

    • @PostRt
      @PostRt  2 года назад +1

      @@Dancing_Alone_wRentals
      I'd recommend having a shop evaluate the truck for damage. If that is not an option, try hammering along the frame for soft spots to see what is good or bad. You could look up the Auto Rust Company as they make Safety Cap repair sections for frames but they will also need to be welded in to repair rusted sections.
      Ultimately, a frame replacement with a good used frame would be the best option. The cost is of that is going to be high and will likely be more than finding another truck with a good frame.
      Hopefully this helps

    • @Dancing_Alone_wRentals
      @Dancing_Alone_wRentals 2 года назад

      @@PostRt sure does, tHanks again.

  • @pcfalcon
    @pcfalcon Год назад +1

    Do you have a shop? if so where are you located? id like to bring in my 02 prerunner double cab tacoma for rust repair. the rear half of the frame needs patched because of rust

    • @PostRt
      @PostRt  Год назад

      No shop. I just did this in my spare time, and I'm glad that I was able to get my Tacoma back on the road. It is stronger than ever and looking great now.
      If you need frame repair, see if a local shop could get you a quote. It seems that most places will charge more to repair than the vehicle is worth. Finding a complete frame to swap can be hard to find and costly as well.
      Hopefully, you can find a place to save your truck.
      Good luck!

  • @leerevell5998
    @leerevell5998 Год назад +2

    I'm about to do this on my Hilux the chassis is just as bad if not worse 🤦 on the original frame there's a radius on 4 sides of the boxed sections sort of 2 c sections welded together do you keep that profile can't see in the video ps one of not the best guides on here are you going to epoxy paint after wards was the outside frame pitted badly are you cutting it out to thanks from UK 👍

    • @PostRt
      @PostRt  Год назад +1

      I know exactly what you are referring to, and I did talk about it a bit in one of my earlier videos. The frame is two pieces pressed and welded together, like you mentioned. There are dimpled vee areas that appear to be a stopper for aligning the two sections before the factory welds were done. I hammer-formed a radius into one of the lower sections to match the profile of the original frame. The outer face of my frame is not that badly pitted and still has a good amount of thickness remaining. I chose to add the inner plates to reinforce those outer sections. That way, the frame could be used as a kind of placeholder jig. The inner face, being completely new, finished it off and boxed it in. So far, I haven't had to form much radius on the repairs.
      Here in the USA, we have a well-known company called Eastwood that sells a large variety of coating products. I haven't fully decided what I will be using yet to protect this truck frame, but I am leaning towards their products.

    • @PostRt
      @PostRt  Год назад +1

      One more thing, since the radius area of my frame wasn't rusted too bad, I cut a clean straight line just past that area for the new plates to join up. I ground a bevel along the butt joint to ensure full penatration of the weld joining the new repair piece to the original framework.
      I hope this helps.

    • @leerevell5998
      @leerevell5998 Год назад

      @@PostRt thanks

  • @jerimy1lisinski
    @jerimy1lisinski 2 месяца назад +1

    how hard would it be to just build a hole new Frame. instead of packing it. I'm relly asking because i don't know

    • @PostRt
      @PostRt  2 месяца назад

      @@jerimy1lisinski There would be much more skill and work involved. I would suggest using a layout table or large fixture when attempting something like that.

  • @vernejohnson8589
    @vernejohnson8589 Год назад +1

    Excellent, excellent video, I own a 2012 GMC sierra and discovered frame rotting on the inner side of the frame, I wanted to see how you make frame repairs, I'm very impressed with your work, I only have 1 question, what kind of welder are you using??? If you could tell me I would appreciate it, grate video very informative and not a short video either, thank you.
    Verne Johnson 😊

    • @PostRt
      @PostRt  Год назад

      I have a 200 amp MIG welder and a 210 amp TIG welder. I have been mostly using the MIG and 0.035" wire. I wouldn't recommend using a 110-volt machine for this kind of work.

  • @ernestopenaloza6449
    @ernestopenaloza6449 Год назад +1

    So you do not paint the inside where you initially placed the first plate?

    • @PostRt
      @PostRt  Год назад

      The metal plates were chemically treated to seal them. In a later video, I showed how I applied coatings to protect the frame.

  • @kshaffer1964
    @kshaffer1964 19 дней назад +1

    Is anyone aware of frame kits available for the last series of Toyota Pickup? I've been looking for kits to fit the 1988-1995 4x4 with single cab. but I've had zero luck locating anything for the frame on the series. Please let me know if anyone has any info on availability. Thanks in advance.

    • @PostRt
      @PostRt  19 дней назад +1

      I don't know of any companies other than Autorust. They make plate sections for a variety of vehicles, but as far as Toyota trucks, it is 1995 and up. You could reach out to the company and ask. They have been in the market for a long time. Maybe the 1995 and up Tacoma pieces could work with some modifications?
      Hopefully, you can find a solution!

  • @jennercastro4934
    @jennercastro4934 Год назад +1

    An idea of how much it might cost to do a job like this. I have a tacoma truck and the chassis is chipping

    • @PostRt
      @PostRt  Год назад

      I would expect it to cost enough to "total out" most trucks. It is so labor intensive and more of a job of passion. If you have a buddy or want to attempt a DIY, it is not too bad. Having the tools to do the job ahead of time is important as well. It also depends on how deep you have to go to fix the issues. I've seen a lot of rust repair videos where it was just surface rust. Those people have no idea what real rust is.

    • @jennercastro4934
      @jennercastro4934 Год назад +1

      @@PostRt Yes, that's what I mean, if I do something, I'll do it right, I want to keep the car, that's why I want to repair it

  • @frankbosley5299
    @frankbosley5299 Год назад

    These videos are great. I'm about to do same thing to my 2003 Tacoma. When did you weld in the tube-metal cross bar? Was that done to maintain torsional rigidity so it wouldn't flex during welding? I watched the other videos (needle scaling) but I didn't see at what point you added it. Great work!

    • @PostRt
      @PostRt  Год назад

      Thank you! I'm glad that you have found the videos helpful.
      I added the temporary supports before removing the crossmembers. I was especially concerned about the trailer hitch area, so I added two back there.

    • @frankbosley5299
      @frankbosley5299 Год назад +1

      Two silly questions. In one of your other videos, you mentioned a grinder disc that was twice the money, but well worth the money. I couldn’t quite understand what the brand name was. Also, what settings were you using o. The mig setup? Thanks! You’ve definitely inspired me and I started ‘surgery’ on the frame this weekend.

    • @PostRt
      @PostRt  Год назад +1

      @frankbosley5299 That is great news, Im happy to help!
      The grinding discs are PFERD CC-GRIND.
      All MIG machines will run a bit differently, and I'm jogging my memory, but I believe my settings were around 18.6-19.0 volts and around 300IPM.
      I'd double-check your machines quick reference chart to get you started and tweak the settings a bit as needed.

  • @thebaldmonk621
    @thebaldmonk621 Год назад +1

    Where did you buy the Steel Plate ??

    • @PostRt
      @PostRt  Год назад

      A local metal supplier.

  • @jimjardine4705
    @jimjardine4705 2 года назад +1

    For those long welds, can you use TIG welding there???

    • @PostRt
      @PostRt  2 года назад +1

      Sure can, TIG welding would also get the job done. I have a TIG welder also but chose the MIG for most of this work because it is a faster process.

    • @jblood1098
      @jblood1098 11 месяцев назад

      Tig would be stronger and less corrosive better weld also 70s 6 tig rod

  • @williedee5051
    @williedee5051 Год назад +1

    Yo good job man i can use you on my truck LOL!!!

  • @Goodfellow7711
    @Goodfellow7711 Год назад +1

    What size welder?

    • @PostRt
      @PostRt  Год назад

      200A MIG Machine
      210A TIG Machine

  • @jeremyr7147
    @jeremyr7147 2 года назад +2

    Ime doing similar repairs, after all the time doing reinforcements. the next weak point of the frame will break in a short time. The repairs are much stronger than original frame design and will force all the stress to the next weak point of the original frame - wherever it is.. crossmember crack off or something.

    • @PostRt
      @PostRt  2 года назад

      Break, build, repeat....
      That seems to commonplace with many things in life.

  • @frankilopez2772
    @frankilopez2772 Год назад

    Where did u buy it the metal to reinforce the frame

    • @PostRt
      @PostRt  Год назад

      I got the steel from local metal supply store.

  • @jblood1098
    @jblood1098 11 месяцев назад +1

    That chrome bumper does not like them grinding sparks

    • @PostRt
      @PostRt  11 месяцев назад +1

      That chrome bumper is rusted out and in dire need of replacement so I'm not too worried about it.
      I want to fabricate a new steel bumper someday for it.

    • @jblood1098
      @jblood1098 11 месяцев назад

      @@PostRt oh 👍 👌

  • @mmingle57
    @mmingle57 2 года назад +1

    Great job!! You must live up in the rust belt!! Isn’t this a shame what happens to your investment from All the salt and environment we have in the northeast! Makes one wonder if the government does this on purpose when they manipulate the weather, using Haarp, but we won’t go down that rabbit hole cause I don’t want to be a conspiracist! But I bet the car manufacturers and governments are all in this together!! Keep up the great work good for another 17 years as long as the engine stays good!

    • @PostRt
      @PostRt  2 года назад +1

      Oh yeah, salt-tastic around here!
      It is a sad thing that I spend a lot of coin trying to wash the salt off throughout the winter and it seems helpless. This truck will be getting a copious amount of protection after it is finished.

  • @lucbesson3470
    @lucbesson3470 Год назад +1

    👍🏻🇺🇸

    • @PostRt
      @PostRt  Год назад +1

      Thank you so much

  • @kljunatic8157
    @kljunatic8157 2 года назад +1

    didn't toyota recall those frames

    • @PostRt
      @PostRt  2 года назад

      Yes they did, years ago....
      Unfortunately that offer has dissolved.

  • @efrenhernandez-m6h
    @efrenhernandez-m6h 6 месяцев назад +1

    Where are you from?

    • @PostRt
      @PostRt  6 месяцев назад

      Michigan, USA 🇺🇸

    • @efrenhernandez-m6h
      @efrenhernandez-m6h 6 месяцев назад +1

      @@PostRt Do I have to make an appointment to have a job like that done?

    • @PostRt
      @PostRt  6 месяцев назад

      I would start by calling a local body shop. They should be able to get you in contact with a place that specializes in frame repair work.
      Another option would be to see if there is a race shop or custom fabrication shop in your area. Places like that are usually well equipped to handle work like this.

    • @efrenhernandez-m6h
      @efrenhernandez-m6h 6 месяцев назад

      @@PostRt How long did it take to make that repair? and how much does that repair cost?

    • @efrenhernandez-m6h
      @efrenhernandez-m6h 6 месяцев назад

      @@PostRt But if I want to take it with you, do I have to make an appointment at your establishment?

  • @jeepsaround
    @jeepsaround 10 месяцев назад

    Hey everyone, it's called a flitch plate, not fish plate.

    • @PostRt
      @PostRt  10 месяцев назад

      No. I'd say you are in the minority there. Fish plate is the correct term used.

  • @PopPopJoe
    @PopPopJoe 11 месяцев назад

    What year Tacoma was it ??

    • @PostRt
      @PostRt  11 месяцев назад

      2003 model year.
      I have many other videos that highlight the truck.

  • @jorgechalarca335
    @jorgechalarca335 Год назад +1

    ¿sería bueno oírlo en español

    • @PostRt
      @PostRt  Год назад

      I believe Spanish subtitles are available. Unfortunately, my Spanish speaking skills are not very good.

  • @marcellebaudry5786
    @marcellebaudry5786 2 года назад

    bravo

    • @PostRt
      @PostRt  2 года назад

      Thank you!

  • @brucenichols9206
    @brucenichols9206 2 года назад +1

    Toyota replaced the frame on my Dad's tacoma for free ............. Toyota, in 2016, settled a class-action suit by agreeing to spend $3 billion to repair millions of Tacomas, Tundras, and Sequioa SUV's with rusting frames. Model years affected are from 2004 to 2008 (or 2010 in a few cases). This follows an earlier extended warranty affecting Toyota trucks from 1995-2003

    • @PostRt
      @PostRt  2 года назад

      He was a lucky guy!
      Unfortunately the Toyota frame settlement dissolved before I could get on board.

    • @Dancing_Alone_wRentals
      @Dancing_Alone_wRentals 2 года назад

      Hello, I have a 2005 Tundra sitting.....Bruce, Do you know if this recall is still in effect?

    • @TheRoadhammer379
      @TheRoadhammer379 Год назад +1

      The recall time frame is officially over. As of January 23 2023 when I type this, you are no longer eligible for the recall

  • @DenMenMaster
    @DenMenMaster Год назад

    насколько экономически обоснован такой сложный , дорогой ремонт ? не проще просто купить новый автомобиль ?

    • @PostRt
      @PostRt  Год назад

      They are many things in life that are pursued in passion. This build has taken more time than it has money and I already have a shop full of tools and machines to do the work.

  • @LuisOrtiz-hp4np
    @LuisOrtiz-hp4np 9 месяцев назад

    Saiudo de PR que sai de crueso de tola para chasi de toyota

    • @PostRt
      @PostRt  9 месяцев назад

      Unfortunately, your comment is unclear through translation.

  • @5barkerstreet
    @5barkerstreet Год назад

    should have use stick welder

    • @PostRt
      @PostRt  Год назад

      Oof!
      What is superior in that process?

  • @JoseSanchez-hn9vy
    @JoseSanchez-hn9vy Год назад +1

    Can you fix my truck?

    • @PostRt
      @PostRt  Год назад

      I wish I had the time to help you and others out. Hopefully, these videos provide some guidance on what to look for and ways to go about repairing it. I wish you the best on your truck repairs.

    • @JoseSanchez-hn9vy
      @JoseSanchez-hn9vy Год назад

      Seriously where are you located that way I can bring my truck to your shop

  • @davidwood1923
    @davidwood1923 2 года назад +1

    Hmmm... That Ain't Breaking... At Least Not in That Area

    • @PostRt
      @PostRt  Год назад +1

      Gosh, I sure hope not!

  • @scotty362100
    @scotty362100 2 года назад

    LMFAO , bro has a car lift and STILL lays on the floor welding up the frame, and working on his knees and back! Not the sharpest pencil in the drawer - huh?!

    • @PostRt
      @PostRt  2 года назад +1

      Well since you asked, apparently not, Bro....
      I understand why you said what you said because obviously you don't know much about these kinds of repairs. I'd like to see some of your stellar repair work because with a mindset like that it shouldn't leave the garage.
      Try cutting out a bunch of your "structural" frame then lift the weight of that very vehicle it up while it has been compromised.
      Do you like Tacos? Because that is what you will get; tweaked, bent, probably broken.
      Also, Who uses pencils anymore...

    • @scotty362100
      @scotty362100 2 года назад

      @@PostRt Yet the remaining "structural" frame is strong enough to support it on 4 tires - but not 4 posts of the lift! HaHa did you even think about your reply before posting? Like taking candy from a baby, gottaq love YT "creators".

    • @PostRt
      @PostRt  2 года назад +1

      Hey Bro Bro, I knew you would be back. You just cannot accept a logical answer but then again, I really didn't think you would understand how technical things work anyway. It is okay to be wrong and move on with your life. Your that type a person who gets stepped on in your real life so you put on your big boy pants, wipe the cheeto dust of the fingers, and spat your tough guy talk.
      Thanks for the laughs today 😆

  • @jamesford7182
    @jamesford7182 Год назад

    All of the videos I have seen are nothing more than cosmetic fixes. This one included.
    I have yet to see one that addresses tensile strength, RMB, section modulus or any of the relevant details required in proper frame work. Throwing 45,000 psi steel at a rusted out 70,000 psi frame rail and then changing the temper of all of the metal. Replacing a smooth bend in high tensile steel with thinner pieces of lower strength steel and welded seams just isn't the fix people think it is. Perhaps the original frame had an RBM of 1,700,000 PSI and you restored it to 500,000 PSI plus the addition of scads of stress concentration points like little tabs in the web of the flange or sharp corners in lieu of large radii. But, what do I know? I only worked for OEM truck builders for 45 years.
    While I am more familiar with heavy duty truck frames for class 8 type chassis, the same principals apply to the light weight stuff. Do it yourselfers would be doing themselves a favor by downloading the original manufacturers body builder manuals at the very least, and reading the damn things, before doing this stuff and spreading misinformation on youtube.

    • @PostRt
      @PostRt  Год назад +2

      Cool story, thanks for sharing.
      Let us know when you do find the correct video so the rest of us losers can learn a thing or two from it.

    • @dont-want-no-wrench
      @dont-want-no-wrench 4 месяца назад

      it is at least more than a cosmetic fix james. and full original strength isnt required here anyway.

    • @jamesford7182
      @jamesford7182 4 месяца назад

      @@dont-want-no-wrench Excuse me. I don't believe in doing things half asses when it comes to be basic structural members. I have seen trucks that literally split in half because some moron decided to increase the length of the frame. One was a nearly $200,000.00 fire truck where someone took the front half of one truck and welded it to the back of a different truck. Worked fine, until it didn't and broke in half. Nobody got injured but, it got real expensive for him. He's damn lucky nobody got injured when it broke.

    • @MichaelPatrick-pq9xl
      @MichaelPatrick-pq9xl 2 месяца назад

      @@jamesford7182 Please explain your recommended method of repairing a frame like the one shown in this video. There are a number of people who would appreciate a description of how an OEM frame like this one could be repaired, particularly when OEM frames are no longer available and so owners must do the best they can to prolong the life of the existing frame. Thanks in advance of your reply.

    • @jamesford7182
      @jamesford7182 2 месяца назад

      @@MichaelPatrick-pq9xl First, I read the body builder guide for that vehicle and refer to the section on frames. There are actual, printed and published manufacturer recommendations for frame repairs. They don't just print manuals for shits and giggles, they do so for two reasons. One, so a competent person can properly repair and/or upfit their product. Two, if, God for bid, they end up in a lawsuit because some nitwit screwed up their product and it cost someone a lot of money or killed someone and gets that deep pocket itch. Every manufacturer I have worked for had to constantly defend themselves in these type of lawsuits.
      Thus, the short answer is RTFM.

  • @jonnyhighviz1736
    @jonnyhighviz1736 2 года назад +1

    Your welds are crap mate lol

    • @PostRt
      @PostRt  2 года назад +3

      I know and thank you 😆
      I've never taken a single welding course in my life.
      It is like telling a toddler that they suck at reading...

    • @TheRoadhammer379
      @TheRoadhammer379 Год назад +1

      This criticism coming from a dildo with zero content showing good welds. 😂 gotta love internet experts.

    • @jonnyhighviz1736
      @jonnyhighviz1736 Год назад

      I've been fabrication for twenty years mate I no my welds noob

    • @rickinmi
      @rickinmi Год назад +2

      @@jonnyhighviz1736 But not, apparently, your spelling, grammar or sentence structure.

  • @hswing11
    @hswing11 2 года назад +1

    The frame was made for the intended use .

    • @PostRt
      @PostRt  2 года назад +1

      It sure was and it has given up on me. That is why I am only putting back close to what is needed to repair it. I am not slapping on a 1/2" thick monster plate in there. Tons of people have welded reinforcement plates over existing factory frames to increase rigidity, especially when turning them into tough offroading machines that will endure a lot of abuse. When you ask more from something than it was originally engineered is when you run into problems.

  • @fghjkuirp56
    @fghjkuirp56 2 года назад +1

    почему при сварке много искр-может газ плохой попробуй.

    • @PostRt
      @PostRt  Год назад

      A MIG welding process produces sparks and spatter. Proper setup and clean metal preparation will help reduce it but it is not as tidy as TIG welding.