5000 Watt Electric Dual Motor SUP
HTML-код
- Опубликовано: 13 сен 2024
- Thank you for all the nice comments on my last video. I'm sorry for taking so long for my videos. Let me know your suggestings for improvement :)
Motor: 2x BL Motor SSS 56114/350KV / 10Y
ESC: 2x Boat ESC 6-12S 200A
Propeller: 2x P9412 (de.aliexpress....)
Batterie: 2x 6S 30C 5Ah LiPo
Wow, nicely done! Rig that and being able to foil as well! You are doing great, takes hundreds of falls to learn it. MUCH help on the internet, some great video guides now available if you want to shorten the learning curve.
Love the idea of it being used as a tow vehicle. The tow rope obviously needs to be longer, but I assume that was the range limitation?
Awesome build!
Thank you :) yes the rope could be a little longer but it was totally fine. The jerking was not from the transmitter range limitation but was because the throttle is very sensitive and the propellers need some time to spin up. I will test the range soon :)
Sehr gut geworden! Freue mich auf mehr Videos!💪🏿☺️
Ja man endlich hast es fertig gemacht, ich fand’s das Ding richtig gut geworden ist :)
Meeeega! 😍
needs to add a 8 degree angle to have the props create lift so you can plane the water for top speed and you need to add a vortex wing with the props so close to surface you losing efficiency this is a wing above the prop that creates density at prop
Great suggestion. I will definitly try that :) Which vortex would you suggest. Because I tried a 3d printed wing at the fin to lift the back out of the water, but the drag was way too high so it wasn't faster. I'm also looking for a better propeller with less cavitation, since I think a prop guard would reduce top speed and its more expensive.
Ahh I've been waiting sooooo long for this and I couldn't be more happy, incredible build my friend!!! can't wait to see more, (wink wink, nudge nudge) 😂
Thank you :D sorry for the long waiting. I can make a huge compilation of fails 😅
@@EOLAND99 how did you seal the motors to use them underwatter??
Das sieht richtig spaßig aus! 😍
Sehr cool! Was eventuell das ganze schneller/effizienter machen könnte ist eine ordentliche Abrisskante von einem hardboard. Die Runde Kante von dem SUP bremst ordentlich
Sehr, sehr, cooles Teil hast du da gebastelt! Bis auf die Tatsache, dass sich NIEMAND vor die Kamera stellen sollte passt alles! Solltest also nächstes Mal die Zuschauer vor Ort bitten, dass die nicht ins Bild rennen :D :D :D
After two years of radio silence it's great to hear from you again! I knew you would surprise us with something new, it's awesome man!
I think moving your motors towards the center of the board would help to increase the speed and bring the nose down, have you tried changing the angle of the motors?
By the way, how did you seal/waterproof the solder joints?
I could change the angle but in what direction. So the back of the board comes more out of the water. But since the whole board bends a little bit I don't think there will be much improvement 😅
@@EOLAND99 I guess I would mount both motors on sheet of plywood and then strap the whole thing using ratchet straps to the center of the board making sure to keep it as streamline as possible, if that makes sense, I know it's could be a lot of work but I'd give it a shot :)
Great build my friend. I thought your single prop version was pretty good this one hits all the boxes. It’s quick, maneuvers well and is cheap ........ compared to anything you can buy today. I love the hydrofoil towing idea. I have been working on a boogie tow. To do the same thing . It goes like a stabbed rat but I can’t control it very well a fail video is on my channel but it’s a great idea to make your power Sup a hyrrofoil towing device too. You were getting some pretty decent speeds there my friend 😁🤙🏼
I did notice that you had the paddle in one hand and the remote in the other hand. U should try a mini skateboard remote. Put it into a balloon and tie a knot in the balloon now it’s waterproof....then tape it to your paddle right where you place your lower hand now you can control the throttle and use the paddle to steer or help balance you. That’s what I do on my builds and it works well. Use electrical tape to tape the remote to the paddle and set your remote up and have it on before you put it into the balloon. Then test it before you tape it to the paddle.
Looking forward to more videos when the weather warms up .
Nice job sir 🤙🏼🤙🏼😁
Very nice to hear from you. I tried using a balloon for waterproofing but I need a giant ballon for my remote :D The boogie two look so cool. However my plan is to make the SUP into a ground effect plane :D
Great videos
now that`s cool stuff !
Super Job!
Nice job!
and when the foot breaks, it smashes into 1000 pieces... epic...
Negative Joe!
You rock, man! how i envy you... :)
Was ein geiles Teil 👍
What motor and propeller combination would you now recommend with your experience for a single motor setup? Do you have links where you purchased the parts? AWESOME JOB!!! keep up the good work 👍
Hallo, wie wurde der Motor abgedichtet?
I would recommend a 360 kv motor with a 120mm aluminum 3 bladed propeller or a 94mm diameter 4 bladed aluminium propeller with maximum of 12 S and 200A.
All the parts are available on aliexpress
Cool dass Du am SUP weiter baust. Warum so verhältnismäßig große Propeller und "nur" 6S? Ich würde ja eher etwas kleinere Propeller und mehr Spannung fahren. Brushless Motoren nehmen ihre Power aus der Drehzahl. Die Propeller selber sehen auch seltsam aus. Betreibe selber RC Boote, bei denen sehen die vollgetauchten Propeller komplett anders aus. So genannte Eco Propeller.
Ich würde auch noch eine Winkelverstellung vom Antrieb vorschlagen, also dass der Antrieb auf und ab geschwenkt werden kann. Bringt sicherlich was beim Topspeed wenn das optimal eingestellt ist.
Ich könnte es auch mit 70mm propellern versuchen. Habe nur einen aber ich dachte ich brauche mehr Schub um auf die Wasseroberfläche zu kommen. Ich könnte die Motoren auch mehr neigen um das heck mehr aus dem Wasser zu bekommen. Bin mir aber nicht sicher wie viel mehr mal rausholen kann. Vielleicht sind 12S und drei motoren das beste.
@@EOLAND99 12S und kleinerer Prop klingt auf jeden Fall gut. Da reichen sicherlich 2 Motoren auch um sehr schnel zu fahren. Bin gespannt wie es weiter geht!
Schade das nicht auf deutsch ist, aber cooles Board was da gebastelt hast 👍🏻
Hallo, guten Tag. Schönes Ding. Eine Frage: Ich hab gesehen, die Motoren sind hinten abgedichtet. Sind die vorn auch wasserdicht oder laufen die voll ? Danke, Gruß, schönes Wochenende.
Thanks for sharing! Do you know if a jet with the same motor would be more efficient?
Congratulations Christian! Excellent!
I'm fabricating my own electric surf board and I would like to know if you can recommend me a kit for it (battery + motor + controller + propeller).
Thanks in advance!
Sehr schönes Teil. Und der Motor war waterproof oder hast ihn Wasserdicht gemacht??!
Der Motor ist nicht wasserdicht, was nur den Lagern zu schaffen macht. Außerdem bräuchte an noch ein zusätzliches axiales lager. Sand ist allerdings ein großes Problem. Er macht das Kevlar am Rotor kaputt. Deswegen ist ein wenig Schutz vorne nötig.
Good afternoon Very good project, congratulations. How long does the battery last on average?
Hi Christian, Great video, with 2 ESC how you are controlling them? is it Skid control? may you advice the setup between 2 ESC receiver and transmitter ...Thank you in advance
Thank you :) So two channels from the reciever are going into the arduino and there I'm using this code to calculate the values for the two ESCs.
#include
int channel[2];
int lgas;
int rgas;
int gas;
int ligas;
int regas;
Servo lESC;
Servo rESC;
void setup() {
pinMode(7,INPUT);
pinMode(8,INPUT);
Serial.begin(9600);
lESC.attach(9,1000,2000);
rESC.attach(10,1000,2000);
}
void loop() {
channel[0]=pulseIn(7,HIGH);
channel[1]=pulseIn(8,HIGH);
gas = map(channel[0],1500,2000,1000,2000);
int l = constrain(channel[1],1500,2000);
int r = constrain(channel[1],1000,1500);
lgas = gas - 2*(l-1500);
rgas = gas - 2*(1500-r);
lgas = constrain(lgas, 1000, 2000);
rgas = constrain(rgas, 1000, 2000);
ligas=map(lgas,1000,1950,0,180);
regas=map(rgas,1000,1950,0,180);
ligas = constrain(ligas, 0, 180);
regas = constrain(regas, 0, 180);
Serial.print("links gas");
Serial.print(ligas);
Serial.print(" -a ");
Serial.print("rechts gas");
Serial.println(regas);
lESC.write(ligas);
rESC.write(regas);
}
I adjusted the values by trial and error. You can monitor the output and see if everything is corrct. The Value 1000 would be zero throttle and 2000 full throttle.
@@EOLAND99 that's awsome I thought arduino would not handle such current and voltage ...thanks heap for the tip
Hello! I love all your videos, I would like to know where I can buy all the pieces, can you put a link to the store? Thank you❤
muy muy guapo!!!
hi may i ask why you are using those expensive propellers. have you tried 3d printing propellers. i would be really intrested to see that. (yes im that one guy that asked around 15 questions in your last video XD)
So nice to hear back from you :)
I could try 3D printing one but I testet one plastic propeller and the higher the RPM goes less thrust is produced. So the propeller needs to be thin and that is only possible with metal propellers.
@@EOLAND99 can't you instead of making the whole propeller thin. Only make the edge thin. Like a knife only less '' steap'' if you know what I mean.
And it would make a really nice video. If you won't mind😶
And maybe it would be a nice idea to make a duct around it. That could increase thrust.
Mit 5 Kw könnte Wasserski klappen mit einem 3,8m Schlauchboot und 7,5 Kw Benziner hat es geklappt elektro- drückt aber deutlich kräftiger .
Ggf den Propeller mehr auf Schub ausrichten /wählen denn ca 30 km/h reichen dicke aus
You know power boats are already invented eh 😜😜😜😜😂😂😂😂
Really interesting bike there, u build it ?
No it's bought and very expensive. It's called Riese&Müller Load 75 touring HS
FELICITACIONES,AMIGO TE SIGO DESDE ARGENTINA ,ERES UN GENIO.TE CONSULTO FUNCIONARA ? LIPO DE TRES CELDAS ,11.1V Y 6000MAH EN PARALELO GRACIAS AMIGO FELICITACIONES
What KV motor did you use im thinking of purchasing 360KV Motor it’s the same brand as the one you used. Do you think 360 is good or would I need a different amount do power my paddle board
Hello! If you leave 1 motor, what will be the speed and how many volts do you need? please answer dear
Kann das sein dass der see in Mörfelden ist?
nicht schlecht :D
@@EOLAND99 hab ich doch richtig gesehen ^^
Hi dude. It's awesome. What esc for single motor you recommend? I want buy 56114 700kv.
better get the 56114 360kv or maybe lower so you can use a bigger propeller or 12S with a small propeller. You definitly need an rc boat esc with minimum of 6S and 200A and a Propeller with a diameter of 94mm. That is what I got, but there is a lot of room for improvement. Also the bearings of the motor will get louder, so for long use an axial bearing should be used or better a waterproof motor like this one:
de.aliexpress.com/item/4001062703760.html?spm=a2g0o.productlist.0.0.4bc22e18JNBNqT&algo_pvid=05ced100-2a29-4b90-a098-e72be119c71d&algo_exp_id=05ced100-2a29-4b90-a098-e72be119c71d-36
@@EOLAND99 What you think about that kit? ruclips.net/video/XwMpcMNjguo/видео.html
Kann man so einen Motor mit der Leistung irgendwo kaufen??
Nice so you have 6s 10ah or 12s 5ah?
I currently use 6S 10Ah 30C for testing. I tried 12S 5Ah 30C but the lipo only lasts 3 seconds on full throttle so in order to test 12S I need more C or capacity.
@@EOLAND99 what is your speed on 6s? around of course
@@EOLAND99 I was thinking to use one solar panel 100 or 60W but probably not for sss engine
What power do you recommend for the open sea?
I would make one for my kayak
For long distance and durability I would take a trolling motor. It will be slower but way easier to build. If you want more speed you need at least 2000W.
What esc do you use ?
What remote control type?
Was hat dich das setup ohne Board gekostet?
um die 700€
Hi Cristian. İch habe eine frage. İch habe ein İTWİT 3 und möchte gerne das sistem bei mein kano haben. Wie kan ich mir das bekommen. Was du gemacht hast...?
bonjour, do you sell the set (total equipment motors) ?
ist der motor wasserdicht?
Ich habe ihn nicht abgedichtet aber er funktioniert unter Wasser weil die spulen isoliert sind. Besser wäre aber ihn mit silikon abzudichten.
Hi Christian , I'm in the process of making a system but less spectacular but trying to be more efficient ( drill gearbox inside)like William Fraser on youtube ,can you tell me your consumption in amp at low speed ,between 3-5 km/h ?
Not more then 20A but the current in the beginning will be higher. In my last video I experimented with low throttle inputs and the most efficient results where between 10A and 40A.
Hi Christian ,
Hi
How do you run electric motor ender water?
brushless motors can run underwater
สนใจ
Doesn't look manatee friendly.
Warum nicht direkt v8 Motor dran. Vom Gewicht fast das gleiche.