How to Rebuild Caliburn G and Koko Prime Coil Head with VAPJOY Rebuild Kit | Tutorial
HTML-код
- Опубликовано: 21 ноя 2024
- 2021-07-18: If you still have problem with Caliburn G0.8ohm rebuild, please go to our latest video from this link to watch more tips, thank you. • Caliburn G0.8 DIY Rebu...
VAPJOY Released new DIY Rebuild Kit for Caliburn G. It includes 10pcs 0.8ohm A1 Mesh Coils, 20pcs Cut cotton and 1 Rod. The Rebuild Kit will refresh your Caliburn G pod after Rebuild.
Please watch our tutorial video before your rebuild, any question, feel free to contact us:
For Technical support: vince@vapjoy-ecig.com
For wholesale: wholesale@vapjoy-ecig.com
Stay tuned and more DIY Rebuild Kit will release to fit other pod too.
Thanks
**SOLUTION AND GUIDE**
If you have successfully build the coil and it taste burnt you need to use 3 layers of cotton instead of 4 around the coil. Simply follow the video and cut a sheet off so you have 3 layers. No more burnt taste!
If you have a red blinking light, make sure the flat side of the coil is down before wrapping. Leave the coil nail in while cutting the cotton to avoid the coil compressing which will cause it to short. You must be very careful not to press the cotton once the nail is removed. Before removing the nail it is also good to move the nail around in circular motion to create space between the coil legs.
Hi, Justin Le, thank you for professional solution.
Alright mate, let's try it also
dear, i did the same still getting burning taste maybe the cotton which is used in this rbk in not so much good, though i order from AliExpress as the VAPEJOY guyz say to do,even though i am facing this issue.
make a video explain... all tests BURN... wtf
@@vapjoy84 make a video explain new method... all modes burn with me
Worked very fine for me! I ordered many coils and cotton from Ali. I probably never have to gonna buy Caliburn G-Coils again.
Thank you very much! :-)
2 strips of cotton seems to be the best for me. 2 internally, then 1 on the outer. There might be a dirty taste initially, so maybe pre-burning the coil with a lighter like someone mentioned is a good idea.
Also, I agree. 2 internall stips and 1 outer is the best.
so following this video i have learned that even with the 1.0 ohm coils you can disassemble, clean the coil, rewick (even with normal cotton, just spread it out so its basically flat) and re-assemble and the coils work like new. important to make sure that the cotton isnt too thick, or the coil will deform.
Going to try one of the mesh pods tomorrow and see how that goes
good job!
How to get strip cotton
Just a note. Even with only 3 layers, the cotton in the repair kit is thicker than in stock coils. I've found with 3 layers, priming and leaving overnight to soak in fully solves this problem.
my friend, please check this video: ruclips.net/video/xbCaxFH4PDA/видео.html
@@vapjoy84 That's very helpful. Thanks!
Prepared store po sa shoppe or lazada boss ? Mka bili nito at mga gamit pang dismantol.
aliexpress store available.
how can i get cotton and mesh coil to rebiuld my coil
What are those 2 metal rods? Are they burning out or something? Isnt it enough just to change the cotton?
Impress, worth the hustle? what about thin coils for mtl? :D Im looking for rba @koko
*THE SOLUTION SO THAT THERE IS NO BURNT TASTE*
I have tested it successfully.
- Use with only 3 layers of cotton.
- On 1 side of all 3 layers of cotton are loosened, by using pointed tweezers.
- With the 3rd layer of cotton and the single strip, use sharp scissors to cut holes in the middle along the cotton layer. Hole width ~1mm, hole spacing ~3mm
Its hard?
@@Иракскоесоветское This is very easy to do
it works perfectly after?
May caliburn g2 po ba kayo sir? Rebuild kit
Pwede kaya to mga sir sa OXVA Xlim pods?
1.2 ohms sana gusto ko eh
good day ! ano pong tawag sa set na yan at san po nabibili
Untuk Pod kuy eazy bsa ga kk
Can i but this kit to Rebuild Luxe PM40!?
Can I still get these in the UK
I'm having the blinking red light problem like many others, and i've already checked if the leg coils touched each other. Also, i built it perfectly like the tutorial and it still got the problem. Can u guys post a fix on this?
when the leg go through the coil housing, does the leg touch the metal? and make sure the coil not twisted before rebuild(because the coils are very soft).
@@vapjoy84 also, can u guys improve the coil or maybe the cotton, since the taste is weird. It's not really similar to the original occ
I did exactly the same thing as the video but the pod doesn’t work, it’s blinking red right instead of working
Same problem here
Klau beli rebuilnd kit nya di mana bang
which type of cotton is used here plz tell me
Ye kahan mile ga
Make video about rebuild coil Voopoo DragX 80w please
you can find more video on our channel regarding to pnp vm5/6 tpp dm1
Can this 0.8 ohm be used on the Ursa baby or not?
can you rewick other type of pod brand using this kit?
can I use this to aegis pod? thanks a lot
I do the same but doenst work :( when i press the button i see the red light can you give me a advise to fix it?
Bro i am getting burning taste after the second day, please help me, i used one cotton piece, folding it 2 times then wrapping it over the coil.
please check feedback from Justin Le on top. *SOLUTION AND GUIDE*
@@vapjoy84 ok i am trying right now
@@vapjoy84 dear, i did the same still getting burning taste maybe the cotton which is used in this rbk in not so much good, though i order from AliExpress as you say to do, though i am facing this issue
Cam I use this kit for the a2 pod?
I had 6 tries to rebuild and all just taste like burned cotton. I already tried installing the mesh coil side by side, still taste like shit. What would be the problem there?
Why he doesn't reply this comment??? i tasted same like shit
Likewise. Taste like burnt coil
It's because you cotton doesn't wet enough.. Maybe when you rebuild that cotton to dense.. From my experience.. Cotton from rebuild kit it too dense to compare original part from factory.. So after rebuild you need at least wait 10-15 minutes
Even waiting for an hour isn't enough
Hi! I use this to build my Caliburn Koko prime it works just fine. Flavor is good, I am using freebase juice and nic salts both are okay. I suspect the cotton is too tight try reducing one layer and the alignment of the wicking slot. Please remember if cotton too loose you may have a leak. Thanks and hope you succeed don’t give up. You can do it.
I'm doing it exactly as the video shows, but it's coming out with a burning taste
you should wait few minutes after ejuice rejection. but please make sure only one coil leg touch the coil metal parts. thank you.
@@vapjoy84 it worked out thank you. The problem was with both legs touching the coil
@@brunovippy4019 nice job! Congrats
@@vapjoy84 what do u mean by only one leg is touching the coil metal parts? is not both leg is attach to the metal parts?..many try still failed to get it right
@@razaliariffin7622 yes when put the coil legs through the coil holder. Make sure the one to touch middle brass contact not touch metal parts.
How to order kit ?
Hi vapjoy make the nevok feelin SPL 10 kit as well. 0.8 ohm-1.0 ohm is very needed badly.
vapjoy diy rebuild kit for Caliburn G1.0 1.2ohm is compatible with nevok feelin spl 10 coil head
Kit ki price
Could I use it for Smok Novo 4?
I've ordered it and tried already. It works for Smok Novo 4. I used 2 layers of cotton pieces. Thanks for such cool solution for my vape♥
Its only because of bad quality cotton used. Here is the possible solution using this cotton
Just use a needle and make strips on cotton from both side just to make it more rough And then use this cotton. You have to do this both cotton strips. But this is not the long lasting solution because after a little time you are not going to get the actual taste of e juice used because this low quality cotton gets burnt quickly and give not good taste of e juice used. So the best way is to use good quality cotton such as Bacon Cotton.
Would this work for a Caliburn G2 pod?
It does
If you are watching this it means you purchased the product. Good luck hahahaha
How many days does it take for the rebuild coil to be burned?
F
Caliburn koko prime uses the same cartridge as caliburn g. but caliburn koko rime uses a 1 ohm coil, while caliburn g uses a 0.8 ohm coil.
My question is, can the caliburn koko prime use a 0.8 oh coil like in this tutorial? thank you
You can use the 1 ohm or the 0.8 it does not matter. I'm pretty sure they both come with the 0.8 ohm
I rebuilt using this 0.8ohm for my Koko prime works just fine, The problem is, it’s slightly difficult to put through the coil legs with the rod, through the bottom hole of occ. Still can be done.
nose plier 6 inch ?
yes,
Can't reuse the same coil ? Or should change
If you are extremely careful while taking out the original coil, and then heat treat it to remove the residue then you theoretically could, but as much as I tried the original coil always gets bent when taking it out, and because it's mesh it needs to be in prime shape when in use to taste good.
how can i buy it in VietNam
somebody pls tell me @@
for artery there?
not yet
mine is blinking blue? why is that
Burnt taste after a few puffs... Dudes, the problem is that fcking COTTON. Do not try again and again, i did. Then tried with different cotton, cut same size and it WORKS!.
San po ito available? Nawala na kasi sa shope
we recommend you buy from aliexpress.com. thank you for interest.
@@vapjoy84 can you send me a link of the seller. Please thanks
@@richardkirbyapaga4462 mang shop owner there selling it directly from China and all ship very fast. you would choose aliexpress standard shipping for your shipping option, all with good service. thank you,
Hello. Vapjoy and User Caliburn G
I have tried to rebuild. but after that the problem is leaking from air hole. Anyone have same problem, how to resolve that?
we recommend you add one more cotton, or wrap one more round cotton to avoid the problem.
@@vapjoy84 thanks
Di mana aku bisa membelinya
D warteg banyak
@@andreanose1 makasih info nya...
Dan sekarang barang nya sudah dapat....
Saya beli di olshop toko sparepart mobil....
Sesuai dg video nya.... 0.8 ohm
@@DuniaLagu24 benarkah yg engkau katakan itu esperadoo 🤔😲😯
Beli dimana bang?
@@maulanaa7534 beli di olshop
di BL ada, di shopee ada. Rbk xros 0.8 ohm
Ini info asli tak menyesatkan
Tidak seperti si samsudin latif yang suka menyesatkan.
what kind of occ is that?and ohm?
0.8ohm for Caliburn G Rebuild
In Caliburn G2 it doesn't work properly. All types are cotton's going to burn even in 2 puff. I prime it about 2 hour each attempt and did exact same things what you're doing. My previous g is much more compatible with your kit. It seems the cotton won't be wick properly even in 7+ hours to prime. Do you have any solutions or guide for G2 ? I think the response of the G2 firing censor is much more fast than g and it keeps burning. Need help asap.
See 3:39 - these holes have to be aligned. If they are not aligned, the wick gets closed up by the inner shell and the juice has no way getting through. It took me 5 tries to realize this and now every recoil is perfect. No burning.
@@yankis. yeah of course I'm doing exact same, all air holes are aligned and still burning. Now I'm gonna try to rebuild with just one cotton. I already rebuild it with 2 pcs of cotton, folding and making 4 of layer inside the coil, burnt, 2 pcs of cotton cut the half make it 3 layer inside the coil, burnt, now I'm just gonna do with only one piece of cotton and fold it, 2 layers inside of cotton.
@@denizturkucu4485 I use one piece of cotton.
@@yankis. caliburn g2?
@@tr3tya Caliburn Koko
Wer can i buy rebuild kit for caliburn g?
if you could not find the rebuild kit for caliburn G local, we recommend you buy from aliexpress.com
Where can i buy these
if you could not find the rebuild kit for caliburn G local, we recommend you buy from aliexpress.com
Merun sa shopee mga 100 pesos per box
Yeahh just like burn cotton XD...
Thank you
Which way is Thailand ordered? คนไทยใต้เม้นนี้
you would order if from aliexpress.com with shipment by aliexpress standard shipping, it arrive soon.
ไม่เเนะนำให้ซื้อครับ กลิ่นรสไม่ได้เเถมสำลีไหม้อีก
Lods pde ba ako pagawa nang coil sayo magkano.. Po KAYA TF
you would also make tradition coil yourself. we offer solution for vapers all worldwide have fun to rebuild their pod. more pod coils will coming.
Um this isn't mesh! Its something like 27 Kanthal wire..
Lazada มีไหม
many thailand buy from aliexpress.com
I had follow the steps to rebuild, not works for my caliburn G, first few drawing still works, after that taste burnt and in the end leaking out from the airflow!
we recommend you add one more cotton, or wrap one more round cotton to avoid the problem.
Please paste link where to buy Kit for Caliburn G
we recommend you buy from aliexpress.com.
£8 for 4 replacement coils in the UK - this almost doesn’t seem worth it
this is rebuild kit..got 10pcs mesh coil inside it.
It actually is worth it, as long as you got spare time at hand… I bought six rebuild kits (3x 0.8 Ohm and 3x 1.2 Ohm) and paid like 24€.
Thats 60 Coils, for £20!
…minus the first two I fucked up at my first try… :)
follow all the steps ..end up..blinking red not firing..
now ok.but taste so weird..hehe
@@hamcik thank you. please make all cotton sit well, and put coil in middle of it. Make sure wait few minute after ejuice rejection. Rebuild coil need some technical, please be patient and try to improve. thank you again, enjoy fun
I know exacly the problem here. That's because somehow the 2 legs touch each other. It called short circuit.
@@QuangMinh-hc1st bro ơi cho m fb m hỏi với, m đang build nhưng cũng mắc lỗi
@@_llv22 facebook.com/minhamelia209
burn and tasteless..maybe the problem is cotton quality
check the solution and guide from justin le just from the top feedback.
1.0ohm
Hi, my friend, not coming yet. thanks concern
U can use coil master rbk pnp r1 1.0 ohm iam using it its working great
Keep getting a burning taste, tried everything but its just burning.
Did you fixed? If dont, read the comments for solution
@@eduardoguimaraes8318 com voce deu certo fazendo apenas três voltas na coil? aqui ta impossível usar... tenso! pior é que peguei 2 kits.. fritei um tentando de td jeito
nice!
thank you.
If you still have problem with Caliburn G0.8ohm rebuild, please go to our latest video from this link to watch more tips, thank you. ruclips.net/video/xbCaxFH4PDA/видео.html
Can I use this kit for the a2 cause the g2 pod leaks too much, 4pods all leaks from the AFO?
IT'S NOT WORKING. RELEASE A NEW VIDEO WITH MORE DETAILS!
Cotton is shir. Burn taste
we recommend you check Justin Le feedback and solution to solve the problem. since the mesh coil is very small and soft, it's require care job to rebuild.
Waste of cotton, they induce to do wrong, just to spend more and finish fast, making them buy more kkkk
Garrrrrrbage coils. Cool idea. But these coils last a max of a day.
Tutorial 2 for DIY Rebuild Kit for Caliburn G and Koko Prime:
ruclips.net/video/4ksZbyq1Jqo/видео.html
Taste like burn . Useless kit
Where can I get this ???
if you would not find local. You can buy from aliexpress.com. aliexpress standard shipping arrive fast.
@@vapjoy84 thank you