Very nice video, thank you for the clear instructions. I already made three rebuild coils with your first video, the first two meshes I unfortunately fucked up, but then after I made some adjustments by myself (the same you pointed out here in this video) it worked like a charm. Few quick tips from my side is to: 1. Use two strips of cotton (four layers) 2. When wicking the cotton around the coil holder just use one layer (cut three layers away), this way it is easier to get to top part back on again and you don’t deform the coil while trying to get the top on it again. 3. Before you put the top part on again insert the long uniform rod carefully after pulling the other one out. This way the legs don’t connect together again while trying to get the top back on… Your Rebuild-Kits are amazing! They taste better than the original coils. Thank you VapJoy-Team!!! EDIT: The cotton you provide with your RBK is disgusting!🤬 Burnt taste after approximately 20 draws, using traditional cotton made for vaping it is much harder to wick it correctly, wasted three coils because of your low quality cotton and three more while trying to wick with cotton bacon…
Hello, if you have such a situation after 20 times of sucking, it must be the wrong use of cotton flower (cotton flower does not absorb oil, leading to dry burning), or you do not add enough oil, the lack of oil supply leads to dry burning). I have a lot of test samples, I feel that this heating ring consumes oil quickly, so you need to fill oil in time, as long as these can be done, I can pump one for half a month. Hello, if you have such a situation after 20 times of sucking, it must be the wrong use of cotton flower (cotton flower does not absorb oil, leading to dry burning), or you do not add enough oil, the lack of oil supply leads to dry burning). I have a lot of test samples, I feel that this heating ring consumes oil quickly, so you need to fill oil in time, as long as these can be done, I can pump one for half a month
I tried six times and soon succeeded. The points you need to pay attention to have already been stated. It seems unimportant, but it is important for a good result. Don't forget to rotate the mesh coil. The smooth side of the coil will contact the cotton. Finally, when viewed from the top you should see a round hole. There should be no gap between the coil and the cotton. I have been using it for 7 days without any problems.
When you do get Dry Hits here’s the answer: Use traditional cotton made for vaping like Cotton Bacon or something else… It is a little bit harder but works amazing when you perfected the technique, my tip is to use a really tiny amount of cotton. The cotton should have a diameter thats 2mm shorter than the wide of the included strips. Just round the cotton evenly and not to tight with your fingers and put it on the included cotton strips, then there should be 1mm space above and below your selfmade cotton. After that you fold the selfmade cotton so you have two layers, that way it works perfectly for me. No dry hits anymore and long lasting coil life. @VapJoy The included cotton is disgusting…
I was having alot of issues after rebuilding the coil with the Vape Joy Rebuild Kit, after watching this video i will try rebuilding the coil again and will test it if it is having burning taste in just 2 days.
when inserting the pin, the inner wire bends sometimes, so make sure you check this and pull the wire a bit (CAREFULLY) after inserting the pin, to make sure that its straight and not touching the metal parts. or if you already cut the wire, use a small pin or tweezer and push the wire towards the middle to make sure it doesnt touch the metal
I am using it and in the grid only see 7 pins but the product in the video shows 8 pins. I use 4 layers of cotton and still see a burning smell quickly after using it
hello , i have a caliburn gk2 smoke , the problem is the smoke is not coming out , what should i do right now ,it is new one , i dont know what happened to it , please reply me 🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻
Try to use traditional vaping cotton (Cotton Bacon or something else) it is mich harder, bit with the right amount of cotton the re-wicked coils are amazing
Hello. When I wrap it with your kits, it constantly leaks from the bottom of the coil. What is the reason of this ? Liquid flows from the bottom of the coil, not from the cartridge.
hey vapejoy, i just follow all the instruction and it works good, but i have the problem with the flavour, the smoke is normal but i can feel the sweet flavour from the liquid, can u tell me what is the problem so i can fix it better? tysm🙏
Hello, I'm using Vaporesso Xros Mini, I would like to ask is the Caliburn G rebuild kit compatible with the cartridge of my device? As far as I know they both use mesh coils.
In Caliburn G2 it doesn't work properly. All types are cotton's going to burn even in 2 puff. I prime it about 2 hour each attempt and did exact same things what you're doing. My previous g is much more compatible with your kit. It seems the cotton won't be wick properly even in 7+ hours to prime. Do you have any solutions or guide for G2 ? I think the response of the G2 firing censor is much more fast than g and it keeps burning. Need help asap.
I would like to buy a rebuild kit for my GTX coils for my Vaporesso PX80, I have the 0.2 and the 0.3 coils, could you provide me with an Aliexpress seller link, that would be appreciated.
I have tried. But the cotton not wicking well. Juice hard to go into cotton. Any suggestion? When u take the pod out, only can see a lot of bubble coming out from juice hole
I'm getting leaks; after rebuilding a coil and filling it, there is liquid inside the coil. I believe what's happening is the outer cotton is not inserting in correctly because it's too squashed in. Any way to avoid this?
It is because you have too little inner layer of cotton, the outer layer of cotton did not cover the inner layer, you can try again in this way, I will show you a video when I have a chance.
Still burnt taste after a few puffs... Dudes, the problem is that fcking COTTON. Do not try again and again, i did. Then tried with different cotton, cut same size and it WORKS!.
Kanka bu adamın kitinden aldım sardım buhar gayet güzel fakat boğuk bi tat alıyorum. Likit aroması sıfır elimde muji pamukta var nasıl bi pamukla sardın bana bi yardımcı ol kurban olayım
Totally agree its still burnt taste .. I tried again and again .. What kind of cotton you;re using right now?? give me the link and the name of it please
Kit icerisinden çıkan pamukla sarım yaptığımda aroma 0, ayrica yogun pamuk tadi var. Orjinal coille aldigim harika aromadan eser yok. Siz hangi pamukla sarim yaptiniz ? Bu tarz yaprak seklinde pamukta yok piyasada nasıl halledicez bu işi anlamadım.
@@lucasaguiar3205 Comprei algumas GTX 0.8 pra testar Nic salt no GTX GO 80 e tb comprei um Kit pra Rebuild de coils 0.8,1.0 e 1.2 do Caliburn,assim q eu usar uma vou tentar fazer o Rebuild dela se não der certo vale de experiência kkk Mas futuramente pretendo comprar um Caliburn G2 então elas ainda vão me servir... Cara,se tiver alguma informação me passa fazendo um grande favor se eu achar também e quando fizer o teste aqui eu compartilho com vc! Vlw
In Caliburn G2 it doesn't work properly. All types are cotton's going to burn even in 2 puff. I prime it about 2 hour each attempt and did exact same things what you're doing. My previous g is much more compatible with your kit. It seems the cotton won't be wick properly even in 7+ hours to prime. Do you have any solutions or guide for G2 ? I think the response of the G2 firing censor is much more fast than g and it keeps burning. Need help asap.
It’s the low quality cotton that comes with the RBK… Try to use normal vaping cotton, like Cotton Bacon. It is a little bit harder but works amazing when you perfected the technique, my tip is to use a really tiny amount of cotton. The cotton ahould have a diameter thats 2mm shorter than the wide of the included strips. Just round the cotton evenly and not to tight with your fingers and put it on the included cotton strips, then there should be 1mm space above and below your selfmade cotton. After that you fold the selfmade cotton so you habe two layers, that way it works perfectly for me. No dry hits anymore and long lasting coil life.
@@denizturkucu4485 after a few tries I’ve found myself using cottonbacon (in contact with mesh coil) and one layer of the included cotton strips to get the liquid from the tank to cottonbacon. It also is easier to close the coil again when using the included strips as an outside layer (to saturate the vapers cotton)
@@denizturkucu4485 If you need further disclosure just tell me, my way of communicating may lead to misunderstandings. I’m trying my best to keep it simple while explaining things, wich might lead to confusions.
@@denizturkucu4485 another problem is the included coiling tool. The diameter is a little to small for my taste, I’m currently using a coiling rod with a 2.5mm diameter which works flawlessly
![Oasis - Oasis Live '25 [Official Trailer]](http://i.ytimg.com/vi/gol_JnuEtKM/mqdefault.jpg)
Very nice video, thank you for the clear instructions.
I already made three rebuild coils with your first video, the first two meshes I unfortunately fucked up, but then after I made some adjustments by myself (the same you pointed out here in this video) it worked like a charm.
Few quick tips from my side is to:
1. Use two strips of cotton (four layers)
2. When wicking the cotton around the coil holder just use one layer (cut three layers away), this way it is easier to get to top part back on again and you don’t deform the coil while trying to get the top on it again.
3. Before you put the top part on again insert the long uniform rod carefully after pulling the other one out. This way the legs don’t connect together again while trying to get the top back on…
Your Rebuild-Kits are amazing! They taste better than the original coils. Thank you VapJoy-Team!!!
EDIT: The cotton you provide with your RBK is disgusting!🤬
Burnt taste after approximately 20 draws, using traditional cotton made for vaping it is much harder to wick it correctly, wasted three coils because of your low quality cotton and three more while trying to wick with cotton bacon…
Can u do a video for a cottonbacon rewick pls bro
Hello, if you have such a situation after 20 times of sucking, it must be the wrong use of cotton flower (cotton flower does not absorb oil, leading to dry burning), or you do not add enough oil, the lack of oil supply leads to dry burning). I have a lot of test samples, I feel that this heating ring consumes oil quickly, so you need to fill oil in time, as long as these can be done, I can pump one for half a month. Hello, if you have such a situation after 20 times of sucking, it must be the wrong use of cotton flower (cotton flower does not absorb oil, leading to dry burning), or you do not add enough oil, the lack of oil supply leads to dry burning). I have a lot of test samples, I feel that this heating ring consumes oil quickly, so you need to fill oil in time, as long as these can be done, I can pump one for half a month
I tried six times and soon succeeded. The points you need to pay attention to have already been stated. It seems unimportant, but it is important for a good result. Don't forget to rotate the mesh coil. The smooth side of the coil will contact the cotton. Finally, when viewed from the top you should see a round hole. There should be no gap between the coil and the cotton. I have been using it for 7 days without any problems.
When you do get Dry Hits here’s the answer:
Use traditional cotton made for vaping like Cotton Bacon or something else…
It is a little bit harder but works amazing when you perfected the technique, my tip is to use a really tiny amount of cotton.
The cotton should have a diameter thats 2mm shorter than the wide of the included strips. Just round the cotton evenly and not to tight with your fingers and put it on the included cotton strips, then there should be 1mm space above and below your selfmade cotton. After that you fold the selfmade cotton so you have two layers, that way it works perfectly for me. No dry hits anymore and long lasting coil life.
@VapJoy The included cotton is disgusting…
Man, you nailed it! It works great! Thanks!! :)
I was having alot of issues after rebuilding the coil with the Vape Joy Rebuild Kit, after watching this video i will try rebuilding the coil again and will test it if it is having burning taste in just 2 days.
How did that work out for you?
@@iDroiD-Gaming brother tried this new trick, seems to work good for the 1st day, today is the 2nd day after rebuild, lets se what happens.
@@bilalahmed.960 Thx brother
Where did you find that kit?
Have you solved your problem? Or not?
when inserting the pin, the inner wire bends sometimes, so make sure you check this and pull the wire a bit (CAREFULLY) after inserting the pin, to make sure that its straight and not touching the metal parts.
or if you already cut the wire, use a small pin or tweezer and push the wire towards the middle to make sure it doesnt touch the metal
6:59 Helpful hint!
I am using it and in the grid only see 7 pins but the product in the video shows 8 pins. I use 4 layers of cotton and still see a burning smell quickly after using it
I suggest a rebuild video of the pod Renova Zero. Thanks ☺️
Thank you 😊
I tried 2 times and same problem, g2 pod gives red light 3 times and does not fire. Why could it be ? Coil legs do not touch. I couldn't in any way.
Can i use 1.0 ohm jellybox coil in caliburn g2????please answer
hello , i have a caliburn gk2 smoke , the problem is the smoke is not coming out , what should i do right now ,it is new one , i dont know what happened to it , please reply me 🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻
A taste of burning with 3 or 4 layers of cotton... What is going on? It seems to be a bad type of cotton used in this kit. I need help
Try to use traditional vaping cotton (Cotton Bacon or something else) it is mich harder, bit with the right amount of cotton the re-wicked coils are amazing
Perfect my Friend 👍👍
Good video ..
Hello. When I wrap it with your kits, it constantly leaks from the bottom of the coil. What is the reason of this ? Liquid flows from the bottom of the coil, not from the cartridge.
hey vapejoy, i just follow all the instruction and it works good, but i have the problem with the flavour, the smoke is normal but i can feel the sweet flavour from the liquid, can u tell me what is the problem so i can fix it better? tysm🙏
Where can you buy the cotton
Dear Vapjoy which rebuild kit should I use for LP1 coil for Nfix pro?
bro i buy 0.6ohms i will put it on my oxva xlim pro cartridge it is compatible, because it is also 0.6
Hello, I'm using Vaporesso Xros Mini, I would like to ask is the Caliburn G rebuild kit compatible with the cartridge of my device? As far as I know they both use mesh coils.
Спасибо, полезное видео
سپاس و درود
Uh quick question why does the cotton from cali burn rebuild kit taste like fish?
Can you make a video changing the resistance of the caliburn x?
In Caliburn G2 it doesn't work properly. All types are cotton's going to burn even in 2 puff. I prime it about 2 hour each attempt and did exact same things what you're doing. My previous g is much more compatible with your kit. It seems the cotton won't be wick properly even in 7+ hours to prime. Do you have any solutions or guide for G2 ? I think the response of the G2 firing censor is much more fast than g and it keeps burning. Need help asap.
make sure the metal hole for ejuice going into the cotton inside is paralleled
For me this Kit is working just fine with the G2…
@@TheMaxi98King sorry for the shitshow. I was get swindled by some mfers. They sell me fake product and that's why it won't work back then
Were to buy coil
I would like to buy a rebuild kit for my GTX coils for my Vaporesso PX80, I have the 0.2 and the 0.3 coils, could you provide me with an Aliexpress seller link, that would be appreciated.
I have tried. But the cotton not wicking well. Juice hard to go into cotton. Any suggestion? When u take the pod out, only can see a lot of bubble coming out from juice hole
you may reduce one or half round of cotton.
Bu sarim x coili icinde gecerli mi?
I'm getting leaks; after rebuilding a coil and filling it, there is liquid inside the coil. I believe what's happening is the outer cotton is not inserting in correctly because it's too squashed in.
Any way to avoid this?
It is because you have too little inner layer of cotton, the outer layer of cotton did not cover the inner layer, you can try again in this way, I will show you a video when I have a chance.
@@tu421mo Yes, please do. And let me know by replying to this message thx.
@@tu421mo
I have the same problema. Did you solve It ??
Good afternoon the product fits in smoke nord 4 can i have an experience close to mtl?
خیلی عالی
How many days does it take for the rebuild coil to be burned?
lasted more than 3 weeks for me
It only lasted 1 week for me
1.0 ohm better reliability 0.8ohm burn in 1 week but the flavour better with 0.8
Hope you can do rbk for sx mini vi class cartridge
ขอบคุณครับ
Still burnt taste after a few puffs... Dudes, the problem is that fcking COTTON. Do not try again and again, i did. Then tried with different cotton, cut same size and it WORKS!.
Is there any better video than this one on YT? Can't understand fully
Kanka bu adamın kitinden aldım sardım buhar gayet güzel fakat boğuk bi tat alıyorum. Likit aroması sıfır elimde muji pamukta var nasıl bi pamukla sardın bana bi yardımcı ol kurban olayım
Totally agree its still burnt taste .. I tried again and again .. What kind of cotton you;re using right now?? give me the link and the name of it please
Kit icerisinden çıkan pamukla sarım yaptığımda aroma 0, ayrica yogun pamuk tadi var. Orjinal coille aldigim harika aromadan eser yok. Siz hangi pamukla sarim yaptiniz ? Bu tarz yaprak seklinde pamukta yok piyasada nasıl halledicez bu işi anlamadım.
Xros cartridge 0.8 rebuild video please
Hey buddy can you please tell me what gauge of nichrome wire for caliburn g coil... Because rebuild kit is not available in my country... Thank you
this is not regular wire, it is meshed wire
Where to purchase rebuild kit?
does this kit work for koko prime?
Can you do tutorial how to rebuild Oxva xlim v2 .6 ohms 😁
Can you confirm that this goes well with caliburn g2 coil? Planning to do a 0.8 build
diy no problem
I think 1.0 tastes best.
Where to buy that coil n cotton link?
Olá, tem rebuild para coil gt vaporesso?
My man shaking like hell
Bang di belakang kotak vapjoy ada kode ap an itu
Where i get coil leg?
What is the name of cotton
Nevoks occ?
what is the name of cotton???
Any kit for the vaporesso coils and GT CELL ?
GTX 0.3ohm is same with pnp vm1 0.3ohm. GTX0.2ohm is compatible with pnp vm5 0.2ohm Or vm6 0.15ohm
@@vapjoy84 is it compatible with vaporesso coil GTX 0.8 for Luxe PM40?
@@lucasaguiar3205 Conseguiu fazer na Coil GTX 0.8 brother?
@@DviKing.S estou procurando alguem que tenha feito, mas ainda nao achei.
@@lucasaguiar3205 Comprei algumas GTX 0.8 pra testar Nic salt no GTX GO 80 e tb comprei um Kit pra Rebuild de coils 0.8,1.0 e 1.2 do Caliburn,assim q eu usar uma vou tentar fazer o Rebuild dela se não der certo vale de experiência kkk Mas futuramente pretendo comprar um Caliburn G2 então elas ainda vão me servir...
Cara,se tiver alguma informação me passa fazendo um grande favor se eu achar também e quando fizer o teste aqui eu compartilho com vc!
Vlw
Plis rebuild oxva xlim proo❤❤
Pasmado ata sir.. hehehe
English please
smok nord 5 pls
Can you provide me official link on aliexpress?
Hello there,,, please do caliburn G2 recoiling 1.2 ohm occ. Thanks u
They already provide the 1.2 Ohm kits, bought them of AliExpress for like 4€
i want to buy for argus air voopoo 0.8 , send aliexpress link
Can this kit use to replace feelin mini 0.8 om ?
sure try it
Your hands was shaking?? 😔
That's because of the nicotine it'll wear off if you stop vaping for about a week or so
@@Phlmtbkkkkkk😂
Is this compatible for 1.0ohm?
1.0ohm is smaller mesh coil
Burning also this method I’m so disappointed
Use 1 metre of cotton per coil wot a smoke
What size kanthal gauge is that?
It's not Kanthal. Must be Stainless steel 304/316 32G
,👍👍👍
کمتر ج.ق بزن دستات نلرزه😂😂😂
Coil not coyel
আমার লাগবো
cotton in the kit is shit. switch it and try again
Caraio que tremedeira da porra
He… tremors.
tangane gemeter
Every rebuild catridge taste like sh*t better buy new catridge lol
I couldn't hear/Understand half of what she was saying
Something so simple to do, how can someone be so dumb and do wrong? 🤦😂😂😂
In Caliburn G2 it doesn't work properly. All types are cotton's going to burn even in 2 puff. I prime it about 2 hour each attempt and did exact same things what you're doing. My previous g is much more compatible with your kit. It seems the cotton won't be wick properly even in 7+ hours to prime. Do you have any solutions or guide for G2 ? I think the response of the G2 firing censor is much more fast than g and it keeps burning. Need help asap.
It’s the low quality cotton that comes with the RBK… Try to use normal vaping cotton, like Cotton Bacon.
It is a little bit harder but works amazing when you perfected the technique, my tip is to use a really tiny amount of cotton. The cotton ahould have a diameter thats 2mm shorter than the wide of the included strips. Just round the cotton evenly and not to tight with your fingers and put it on the included cotton strips, then there should be 1mm space above and below your selfmade cotton. After that you fold the selfmade cotton so you habe two layers, that way it works perfectly for me. No dry hits anymore and long lasting coil life.
@@TheMaxi98King kit cotton strips stay outside or inside ? Which cotton make contact with wires ?
@@denizturkucu4485 after a few tries I’ve found myself using cottonbacon (in contact with mesh coil) and one layer of the included cotton strips to get the liquid from the tank to cottonbacon. It also is easier to close the coil again when using the included strips as an outside layer (to saturate the vapers cotton)
@@denizturkucu4485 If you need further disclosure just tell me, my way of communicating may lead to misunderstandings. I’m trying my best to keep it simple while explaining things, wich might lead to confusions.
@@denizturkucu4485 another problem is the included coiling tool. The diameter is a little to small for my taste, I’m currently using a coiling rod with a 2.5mm diameter which works flawlessly