**SOLUTION AND GUIDE** If you have successfully build the coil and it taste burnt you need to use 3 layers of cotton instead of 4 around the coil. Simply follow the video and cut a sheet off so you have 3 layers. No more burnt taste! If you have a red blinking light, make sure the flat side of the coil is down before wrapping. Leave the coil nail in while cutting the cotton to avoid the coil compressing which will cause it to short. You must be very careful not to press the cotton once the nail is removed. Before removing the nail it is also good to move the nail around in circular motion to create space between the coil legs.
How doy you enter that rivet pin and both of coil legs in side coil base cap. It's impossible to do. There are no space when pin go through the hole. So how coil legs been enter.? 😭😭
I have tried 7 times to rebuild the coil with the kit, but all failed. The mesh coil ends wraps around and touches causing low resistance. When I tried using 1 strip of cotton inside, it causes thecotton to burn after a few hits. How do you ensure that the mesh ends do not touch during install?
Hello. I made this DIY for my argus z-pod following you. but I think I accidentally touched the wires together. argus z short-circuit protector activated. argus runs but does not fire. is there a solution to this?
Caliburn koko prime uses the same cartridge as caliburn g. but caliburn koko rime uses a 1 ohm coil, while caliburn g uses a 0.8 ohm coil. My question is, can the caliburn koko prime use a 0.8 oh coil like in this tutorial? thank you
It's not same. 1.0ohm coil head not same as 0.8ohm. The rot n mesh coil leg cannot get thru the hole. 1.0ohm hole slightly smaller. Only fit the rot.I have to buy 0.8ohm coil head which the hole slightly bigger than 1.0ohm coil head
Hello. Vapjoy and User Caliburn G I have tried to rebuild. but after that the problem is leaking from air hole. Anyone have same problem, how to resolve that?
2021-07-18: If you still have problem with Caliburn G0.8ohm rebuild, please go to our latest video from this link to watch more tips, thank you. ruclips.net/video/xbCaxFH4PDA/видео.html
because the housing neck is tooo small, if not caution, both legs will touch the metal part and Short circuit will happen, and this is the reason why so many people complains, we have replied so many time below, but not check.
**SOLUTION AND GUIDE**
If you have successfully build the coil and it taste burnt you need to use 3 layers of cotton instead of 4 around the coil. Simply follow the video and cut a sheet off so you have 3 layers. No more burnt taste!
If you have a red blinking light, make sure the flat side of the coil is down before wrapping. Leave the coil nail in while cutting the cotton to avoid the coil compressing which will cause it to short. You must be very careful not to press the cotton once the nail is removed. Before removing the nail it is also good to move the nail around in circular motion to create space between the coil legs.
thank you professional job!
is it compatible with vaporesso coil GTX 0.8 for Luxe PM40?
@@vapjoy84 is it compatible with vaporesso coil GTX 0.8 for Luxe PM40?
i have red blinking light can u show me how to solve it ?!
For me, I use only 1pc of cotton from vapjoy RBK 0.8ohm. It goes well for 3 rounds inside the coil.
How doy you enter that rivet pin and both of coil legs in side coil base cap. It's impossible to do. There are no space when pin go through the hole. So how coil legs been enter.? 😭😭
Is there any rewick tutorial for caliburn koko prime 1.0 coil?
I have tried 7 times to rebuild the coil with the kit, but all failed. The mesh coil ends wraps around and touches causing low resistance. When I tried using 1 strip of cotton inside, it causes thecotton to burn after a few hits. How do you ensure that the mesh ends do not touch during install?
Just do exactly what he does at 1:17
He first rolled the coil and tucked it in sideways if tuck it in where you are holding it, the coils will meet
is it compatible with vaporesso coil GTX 0.8 for Luxe PM40?
Is it the same for KOKO AK2? It uses UN2 0.9 coil
Cant enter the coil legs with pin in to th shoe hole. It stuck. How could do it.? This one is original caliburn base.
I keep getting 3 blinking red lights. How do I fix this?
Charged your device bro
Any other option to rebuild the coil without the rebuild kit
I tried with 3 layers of cotton and started to see more effective. But I don't know if 3 layers of cotton has any effect on the life of the coil ?
By day 2, the burning smell started to appear.
I would like to ask is the Caliburn G rebuild kit compatible with the cartridge of Vaporesso Xros Mini? As far as I know they both use mesh coils.
Can the 1.0ohm coil repaired or rebuild?
Can it without the mesh coil
Hello. I made this DIY for my argus z-pod following you. but I think I accidentally touched the wires together. argus z short-circuit protector activated. argus runs but does not fire. is there a solution to this?
It gives bad taste of flavor. I think the problem is with cotton quality. Can you please share the cotton substitute that gives same taste.
Hola que tipo de tela de algodón usan para las resistencias
Caliburn koko prime uses the same cartridge as caliburn g. but caliburn koko rime uses a 1 ohm coil, while caliburn g uses a 0.8 ohm coil.
My question is, can the caliburn koko prime use a 0.8 oh coil like in this tutorial? thank you
Yes
Can bro
How long does it take for the rebuild coil to be burned out?
My friend, everyone's skill is different. hope you understand.
Can I use 1.0 ohm head coil rebuild this 0.8 mesh? Coz I threw the 2 pcs 0.8ohm head coil.
the coil housing is same with 0.8ohm mesh
@@vapjoy84 aight. Ths will get this then.
It's not same. 1.0ohm coil head not same as 0.8ohm. The rot n mesh coil leg cannot get thru the hole. 1.0ohm hole slightly smaller. Only fit the rot.I have to buy 0.8ohm coil head which the hole slightly bigger than 1.0ohm coil head
@@yieann
Yes, you are correct. I had much difficulty fitting 0.8ohm mesh to 1ohm housing. Coil touching is also problem.
Lol...teste like a burn cutton, u need change the outside with mesh cutton.
Tried rebuilding mine but every time after 3 hits it taste like burned cotton
I tried using mesh cotton as 2nd layer and viola it doesnt taste like burnt cotton
cotton/coil not assemble well.
What to do if they blink blue light 3 times?
time 3:56, please make sure that when two coil legs coming out from coil holder, make sure only one leg can touch the hole (neck) inside.
Quanto tempo dura?
Red blinking rebuild 3x
PnP R1 coil ? Please
Coils burn out after a few hours. Ive tested every single of of them that cane in the pack. Garbage and i cant get a refund.
Hello. Vapjoy and User Caliburn G
I have tried to rebuild. but after that the problem is leaking from air hole. Anyone have same problem, how to resolve that?
you may try to add one more cotton or wrap the cotton for one more round.
What kind or white paper did u use?
*SMH* It's *_cotton_* .
it is just daily use paper.
2021-07-18: If you still have problem with Caliburn G0.8ohm rebuild, please go to our latest video from this link to watch more tips, thank you. ruclips.net/video/xbCaxFH4PDA/видео.html
Not working this.....
link buy plis .....
you can easy to find on aliexpress.com store or shopee store.
Link rbk caliburn g?
many people buy from aliexpress.com
Did he used tissue?
Buyer beware: the coils in the kit burn out after 1 day of use.
Really? Anyone else having the same burn issue?
@@mauriciodellagnese1444 yup agree with the guy...tried rebuilding 4 times, all burnt up after either 1 or 3 hits. Terrible quality.
@@flujarfly damn.. :/ thanks for the feedback mate
1.0 ohm
1.0ohm will releasing soon, under testing,
@@mariorogina1974 finished tested, 1.0ohm mesh, and 1.2ohm mesh release in few days.
@@vapjoy84 when will 1.0 and 1.2 come?
@@joshofosho3 yes, they have came. we can not login into youtube for more 1 month.
2:08 NAG CUT YUNG VIDEO DITO NUNG SA PART NA IPAPASOK NA NIYA YUNG UPPER PART NG COIL *BAKIT MAHIRAP BA IPASOK HAAHH!!!*
because the housing neck is tooo small, if not caution, both legs will touch the metal part and Short circuit will happen, and this is the reason why so many people complains, we have replied so many time below, but not check.
just buy a new occ instead of rebuilding
Yes bro,if fail rebuild.u waste your own flavour😂,better buy new occ.it not expensive
Sakın almayın. Çok kalitesiz iki çekimde bobin yanıyor.
Lol. Burn in one puuf 🤦 bad quality
No coil use shoe 👟 leather for wrap inside holder put 🧽 for bubbles you got a heel of a coil
sapa tahu link shopee. yg ni ?
you can search the product name. it will be easy to find on shopee. thank you.