how to charge a hybrid battery with a 12v battery
HTML-код
- Опубликовано: 4 авг 2024
- In this amazing episode i will show you a simple way to charge the hybrid modules.
just make shure to know that this is no the proper way to do it ok 👊😎... remember that this is only applies if you don't have a charger.
enjoy.
#hybrid #hybridvehicles #battery #mechanical #toyotahybrid #toyota #prius #toyotaprius #electric #electicity #electricalvideos
![MURDER DRONES Series Finale [TRAILER]](http://i.ytimg.com/vi/p6mhC5Iatns/mqdefault.jpg)
Pure Tesla or Edisonian reasoning. Caribbean "situational mechanics" at its finest! Genius! Earned a sub from this viewer!
Love how you keep it simple
“This is not the preferred way to do this”. Jose my grandfathers Chevy in Cuba had a Russia fuel pump and a German master cylinder. What I am trying to say is. It doesn’t matter how you get it done as long as you get it done. Cubanos always find away. Keep up the good work.
🤣🤣🤣🤣
You are awesome 😎 teacher I learn a lot from you 👏👏🙏
Love these series of classes, really learned a lot on how to perform these procedures safely & professionally👍😉
Thanks for sharing Bro, Stay Safe👍
I like your classes keep up the great work
You are the best..i am able to change my hybrid battery by myself..thanks to you💕
Glad to help my brother 🫡✅ don’t forget to share 🫡✅🫡✅
👍👍 Excellent material!
Thank you!
Great job thank you. Easy peazy.
This is so clear and thoroughly explained thank you man
Good video bro. Continue to share knowledge on hybrid
That’s very handy thanks for sharing it
mr.kelly is proud of you sir... thanks
Can you sell me 5 good batteries for my Toyota Aqua
This works just fine. Just don't keep it hooked up too long. I have charged up to 10 at a time. It really suck the 12 volt battery down so I keep a charger attached.
I am doing this right now - my 12 v batt was at 9.6 volts and I attached a charger to it, then I was like hum... should I have that charger attached to the batts too or not - see, when these batt are in the car, they are charged up to 17.8or so volts - so, if you do charge it increments, it will be fine - right now the 28 modules I have are at avg. of 7.54 - I want to bring them up to 8 volts before putting it back in the car - ANY suggestions?
Informative vedio
thanks for your knowledge
Thank you bro from Afghanistan ❤🎉
Based on this video. I would NEVER bring my batteries to this guy!
Very smart 🤣🤣🪫🪫💩💩
I learned about this and batteries in school but the follow up and exposure is needed
very informative
So im hoping to see how you do a load and unload after the charge.. can you also show your machine (balancer). In detail.. like what kind a metal and how you made it from the bottom up. Please 😊 thank you for your videos. Very helpful.
as we can see the bottom is wood. Two rails of aluminum also screws big enough to hold the modules without moving. Hope this help.
Каква машина исползва за бавно зареждане?
Thanks for all of the great information you are sharing. I use your process to balance and Group charge my prius battery rebuilds.. ie connect all Negs and Pos.. to balance.. I use a hobby charger to charge the whole group.. I charge at .5 amp and up to 8.5 volts... the charger shuts off when the collective voltage is 8.5. Then I let it rest to balance. charge again.. repeat... This is what we can Top balancing... ??? My question to you is what could I use to discharge the 28 modules down to 6.3... let rest- balance..... discharge....... let rest - balance.. ie Bottom balancing. My ultimate goal is to be able charge/discharge 28 cells at a time... to recondition the individual cells in bulk. My current system only allows me to charge/discharge 4 at a time. How do I cycle (charge/discharge) 28 cell at one time.. To clarify... I understand balancing and bulk charging due to potential differential current... How can I charge and discharge 28 cells to attempt to recover Amp capacity.. Thank your for your time..
i love your explanation :) and your facial expression too :)
Thank you so much amigo👍👍👏👏, u remind me of nacho libre. My favorite movie
🤨
Your all video class is so much interested from Bangladesh
Thanks for a good video it help a lot.
I’m very glad it helped 🫡✅
Thank you for the classes teacher
What setting would I use to charge the module packs with my EV PEAK CQ3 while on the balancer?
I am Sajid from Pakistan
And your like your vedios
What about using a 12V (output) electrical charger that has an automatic current controller..? It even totally disconnects when the battery module is fully charged, indicating FULL. I would like to know your thought. Thanks
Sir, your explanation in Toyota Prius Hybrid batteries and methods you use to rectify faults are marvelous. I followed your methods and learned a lot.
I have a 2009 Prius and it gives an alarm after several minutes when started the vehicle. But the vehicle runs with less AC. Once you stop the vehicle can’t start again. If you remove the small battery terminal and after few minutes when you fit the terminal back you can start the vehicle.
I checked up with a scanner then you get a fault called “P0AA6” hybrid battery voltage system isolation fault.
I noticed when I remove the batteries some of them had leaked. I replaced them with fairly good ones. But still I got the same alarm again. Could you please help me to rectify this problem.
Hope you would reply soon.
I'm facing exactly the same problem now. Have you managed to fix it?
Hi , thanks for all your video , definitely you are a great help .
Question if i don’t have the tool to balance the cells , can i charge them directly one by one fron the 12v battery?
Love you man
Thanks brother
Jose is top man.
Great discovery. Will try to use
Jejeje not a discovery (i wish) ... but it's just about potential difference 👋😎
@@hybridsolutiondiagnostics interesting battery charger opportunity: sam.gov/opp/2f53591f33004fca8b82fe21ef846f39/view
Thanks again.
You talk a lot dude which explains everything very well beautifully explained
Was that an insult or a compliment? 🤔🤣🤔🤣🤔🤣🤔🤣🤔🤣🤔🤣🤔
@@hybridsolutiondiagnostics its was a heartfelt compliment because i tried your technique and it did work. Another compliment...thank for so much for sharing your knowledge with us
Very interesting
U are the man
Jejeje thank you richard... glad you enjoy the video ☝😎
Great video! I have a 2013 ES300 Hybrid. it was parket for months and now it will not crank. Do yu know how to charge the hybrid system using a regular 12 v battery charger if possible?
very good video very very good
Thank you Jose for this amaizing way for fast charging..what about discharging is there any easy way...
In that way, of connecting and disconnecting the source power faster you become an switching mode power supply! Same principle and you do the control flyback yourself! 👍
Except, no flyback here. Just, switch.
🙋♂️ sir i have a question..which is any possibility to create a plug in system for 2nd gen or increas ev mode range?
Would it be better to balance first, then load them using the battery?
So what charger would you recommend to use?
After full charge do I need to discharge again and charge them again sir?
Thanks for the video, Can we do that with the whole package? all the 28 modules?
I have a question to you is there option to charge this with approximately 10ah 12 v power supply in same duration of means 10 to 15 second may better way to charge when don't have 12v dry or gel battery is that possible?
Can you do this with a Battery Tender at less than 1 amp & just leave it on over night? Or a Harbor Freight 500 mA 12v charger?
I'm sure you get this all the time, but is it possible to charge the HV battery on a gen 2 Prius whilst the battery is still in the car?
Mine is at a useless repair shop as the cat was stolen and the engine won't start after cat replacement. They "accidentally" drove it into the shop from the parking lot on EV mode and drained the HV battery, so I'm guessing I'm hosed since the HV pack gives power to MG1 to start the engine? The issue could be somewhere else too as the car stood for a year after the cat was stolen (2 times in a row).
I'm pretty desperate here...sorry.
So I did this, and plugged the safety switch with my charger still on. It blew the fuse/shorted the charger. I bought another charger, and now im not getting any voltage to the two wires. Before I was getting 278v. Is there a fuse connected to those wires, or did I mess the whole thing up?
I have a 2014 Hyundai hybrid sonata I got a ..stop and park turn off the car on my dashboard check hybrid battery charge I changed the whole hybrid battery and still say the same thing I also changed the starter generator still nothing what can it be???any ideas
Can someone explain why they have to be balanced? Is it just so they can be individually load tested? I have checked all 28 cells and they are (on average 7.75). Will the car balance them after installation?
P.s. I replaced 4 cells with some i bought online and they have about the same voltage as mine. Thanks!
I thought about splitting the hybrid battery pack into two batteries in series and then charging them with a 12v charger. If the battery is 7.5+7.5 to make a 15 volt battery, it would only charge if the 12v battery charger charges at 15 volts. Would it work if it charges at 14.5 volts tho?
Bravo por el trabajo que haces, gracias. Veo que en tu uniforme de trabajo pone tu nombre JOSE HERRERA. Nombre y apellido son de origen español.
Yes, the teacher speaks spanish...
How did you build the battery holder? Anything special?
Hello and thank you.
I like this emergency method.
A question, please:
What is the maximum voltage for module when the battery is full?
Thank you for a great job.
Another subscriptor more.
Bye.
They can reach up to 8.5v... thank you for your support 👋😎👋😎
@@hybridsolutiondiagnostics thank you very much.
@@hybridsolutiondiagnostics Is this for Nickel and Lithium toyota ? or just for Nickel ?
I replaced 2 reconditioned ones but they were about 6 volts sitting in the garage for sometime.will they charge by itself while driving ? Or i have to take them out again and charge?i still get a check light .yes i did load test when i found the 2 bad ones
At 6v they are very bad... nominal it's over 7.2v
Sir i want to know what is the proper current and voltage to charge my 28p 3s hybrid battry pack. Hope more video comes related to charging.thank you.keep it up.nice work.
If I connect a 12v charger to the 12v battery on the car and open the switch will this fast charge hybrid system?
8 volt batteries are available for antique vehicles of 6 volt systems. The 8 volt battery is used to improve starting and of course daily use. This is normal to use an 8 volt battery on old cars.
Why will my 2006 hybrid highlander not charging the traction battery until it reaches around 80km/hr?
is interesting and something to learn, do you have cells for 2012 panamera hybrid 970, I like to use their own system to charge the battery any ideas, I'm planning in buying the Porsche charger for Panamera 2014 and the port charging and hook these up to the system, I'm kind of lost, where to begin.
Send me the cells photo via instagram DM... let me take a look 😎👍
I have a question, if i charge like that do I need to discharge to make it work ???
Hi, Thank you for the video.I have a toyota prius 2010 and it gives me ( P0A80 ) and I did everything in the video and drove 350 miles. After this the code didn't go away. Could you help me, what else can I do?
HELLO, Sir
I have p[rius 2010 but one cell8 is weak so how i can charge or balance parallel with a normal charger with 12 volts and how many amperes should be?
Thanks
Hi there. Thanks for your videos. How about the capacity of the cells? Is it possible to recover capacity of them?
Not to bad modules…
Hi Hybrid Solutions. All my dash lights in 2007 Toyota Camry Hybrid are on (Triangle, ABS, Engine, Check Hybrid System, Check VSC system) with code POA1B, C1310, C1259. Do you think it is because the hybrid battery is weak? Is there anyway to just replace the bad cells in the battery? Thank you.
Do a complete health test and send it over to our instagram DM 👋😎
I have a 2007 Ford escape Hybrid I head told I needed to change my transmission fluid. All the batteries are down. I have a new battery to go up front. I have no one to help me so what should be my first step. I bought a battery charger.
Can you put a trickle charger on them?
thx man, this great , pls in spanish too
I discharged the high voltage battery in my Hyundai Ioniq hybrid ( not plug in , just Hybrid) . Without, the ICE is not starting and without ICE no high voltage battery charging. Can I use this method to charge the HV battery so it can start the ICE? Where would I connect the 12 V battery plus and minus ?
You have to connect all the
Cells in parallel.
At the moment all of them
Are connected in series.
But it's possible.
waiting for the cell load test video, please!
I got hundreds of what I think is v1.5
What can I do with them?
Voltage from less than 1v to 7v
Thx
Please make vedio about touring sport hybrid 2.0
How many cycle do I need as minimum sir?
like you mention , how do you discharge them super fast, as you charge them super fast but how do you discharge them super fast ? thank you
No need to... the load test should not be fast discharge 🤣🤣
Wich machine I can use to teste hybride battery pack damage?
💪👌💪
Hey man I can’t find a 12 volt battery for my Toyota Axio can u help me out
I have hoppy chargers about to do the discharge charge with 2 hobby charges 4 channels each. I also have a noco 12volt charger. My question is if I hook up negative to negative and possitive to positive. Can I charge all at the same time with the 12 bolt charger or the hobby charger.
I was wondering the same thing.
I don't see how not..
..I even considering not putting them all apart but charging in the pack. It's already set up to get charged.
Awesome content!! Does this method apply to Lithium Ion batteries as Hyundai/ Kia use in their Hybrids?? Ty
No my you definitely should not do this with lithium batteries… it’s too much current flow..
Ok you're a life saver!! I'll go the other route and buy a charger... so how many amps should a dedicated lithium battery charger be at when charging? You're a great mentor and thank you for the quick reply.
Can you use a 12v trickle charger for a hybrid battery just to raise up a few modules??
As you just saw in the video 👋😎
@@hybridsolutiondiagnostics Using a trickle charger would work in theory, however most cannot deliver more than a few amps before the thermal cut out activates, on overheat or over current. Using a battery is ok but the voltage will drop to the stage where it is lower than the voltage of the cells in the hv battery where no current will pass to the hv cells.
Hi, as I guess I can charge 8*cells together by 12 v battery. It’s about 60v vs 12v right?
How many batteries can you do at the same time?
What should be the operating voltage of each cell in the vehicle?
How to change SoC for Toyota Hybrid from SoC 80% to 90%?
Hi, thanks for your video, can I use the laptop charger with 19.6v?
Laptop charger has pure AMP and also high voltage, but I think you can charge it anywhere
Hello Hybrid solutions. Do you think a charging socket could be fitted to a Hybrid car to charge the High Voltage Battery while parked overnight at home?
I believe the High voltage battery in a Hybrid would probably be a stack of these 8.5 volt battery packs in series. So I guess about 24 of them in series giving a total of about 204 volts.
Is there a charger that could be connected to the car to charge the High voltage battery. I am hoping that would give enough short range use to get to work and back and possibly not use any gas.
Thanks Brian in New Zealand
Hi brian 👋😎... yes you can... but you will have to tell me which car it would be for because many factors will depend...
@@hybridsolutiondiagnostics hi! I had a similar idea as brian in mind thus I found your video.
I consider sticking a flexible solar panel onto a 2015 Yaris 1.5 Hybrid. What kind of charger would I need between the panel and battery?
Thanks a lot.
Hi, I have a Touareg baterry, my question is if I could charge the baterry in the same way as you or is there a different way to charge? and in another video I looked that you used a special charger, is it necessary to buy one of those o r is there any alternative? I´m writing you from Mexico
No need for VW vehicles… they use Li Ion batteries
@@hybridsolutiondiagnostics oh, I understand, so...is there any way to charge those batteries? Or is there any other solution? Do you have another way of contact like mail or phone? I need help with this, we can pay for your help
Wow, in that case instead of 12 V car battery, can I use a very small and cheap 9 volts battery and just leave it for long time?
Sir, I forgot to mention in my earlier comment that I cleaned all the terminal copper plates and wire cable terminals with alcoholic solution before reconnecting the batteries.
What is the low test sir?
my eyes literally widened seeing him connect the 12v. lol. could use a battery charger with a low amperage, to rebalance them low current.
I'm enjoying the classes, keep up the good work, have you ever done a video on load testing the modules? I wanted tk know what's normal voltage under load and how long should I leave the load on ? Thanks in advance.
That video is coming very soon 👋😎
@@hybridsolutiondiagnostics when!! Its been a month lol i’ve been searching for that part after the quick charging on your machine video 🤪
@@sweetbaby96 gloriaaaaaaa what part? ☝️😮😮🤣🤭🤣🤭🤣🤭🤣🤭
I did my load testing using a 6/12 volt load tester for cars. I found that putting a 20 second load on a fully charged cell will pretty well weed out the weak ones. If the voltage under load dropped to below 6.1 the module was suspect.
@@hybridsolutiondiagnostics AHHH yay you answered..lol umm I was waiting on the 3rd master class to this. I thinking what comes next from this video? the load test and the discharging with the same idea of having some limited instruments to work with on the batteries from home. And what do you think of the Smart-tech SBC-50 Battery charger instead of the 12v battery and what do you think of the SkyRC max B6 AC V2 battery Charger/discharger? How would you use it or would you recommend it? And would you use Cen-Tech for load testing?? And how would you use it?
Thank you for your videos by the way..I love your silliness with the expertise behind it.
Can I connected all 20 modules together and then use your technic
Waiting for answer..........
You can do this with any number of cells as long as they are in parallel. Just be careful and take your time.
Guys, I need help. On Prius 3, where is battery block number 1, on the left, or at the right side, close to battery contol unit and fan?
Always the main negative is number one ☝️
If I charge all modules and they don’t hold the charge what happens???
Throw them to recycle 👋😎👋😎