Muy buen video, me ha servido de mucho... mi Delonghi magnifica E3000B a veces falla al ir a encenderla y tengo que insistir un rato en el botón de encendido... no se si con el tiempo tendré que cambiar todo el módulo de la botonera... sabes cual podría ser la causa? 1 saludo y gracias
Thank you so much for posting these videos for fixing the Magnifica! Very helpful. Would you mind telling me a good resource for purchasing all the o-rings needed to refurbish my entire machine. I have developed a pretty big leak from my steam wand and i figure i should replace all o-rings while i have the machine already torn down. Thanks again for the help!
Milen, Your videos have been very helpful in maintaining my Rialto EAM 4500. I do have a new problem that I cannot find any information; When I push for hot water, I get a little steam and the pump runs for a second or two then the pump stops. Any suggestions? Thanks in advance. FYI I did replace the hot water solenoid which did not help the problem at all.
Milen, I replaced the orings in my boiler. When I re-installed I make coffee but the coffee runs into the tray rather than through the diffuser. The warm up and ending rinse also go directly into the tray. I tried another diffuser but did not help. any suggestions?
Здравей, благодаря за полезното видео! Бойлера на моята машина е в почти същото състояние и аз скъсах двата болта в средата и смятам да правя същата процедура с пробиване и нова резба. Гледам, че са те питали за о-пръстените и си препоръчал И-бей. Има ли от къде да се закупят като цял комплект или по отделно всичките от България? Благодаря предварително!
Had purchase this guy with www.ebay.co.uk/itm/DeLonghi-De-Longhi-EAM-kleiner-Dichtungssatz-für-Boiler-Durchlauferhitzer/260990447013?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649
Здравейте Милен Гледам вашите видеа с голямо удоволствие а също и научавам много нови неща от тях . Бих искал да ви попитам дали според вас може да се смени бойлер на делонги еам който е 900 или 1000 W с бойлер за esam който е 2×600 w и дали според вас е безопасно за кафе машината? Благодаря ви предварително Гено
@@koutuang9959 Yup , go ahead, but don't forget to let it dry... In general water and electronics is a bad combination, but in this case you have only heater terminals and wires, so it will be fine if you dry it, but rememver to wear some gloves, because this shit reacts with skin...
NOT EVEN WORTH REMANUFACTURING/refurbishing THIS PIECE! Just spend 50-80 dollars on ebay for a new one, and replace. Seriously. this is not worth it when yours was as corrodded and leaky as mine was. I put a new generator in there, and it works like brand new again.
It's worth for me. For you it's 80bucks for me it's 480PLN=125,15USD. It's almost the same price for whole express. Seals I have for a couple PLN(from my firend), so it's worth for me compred to new unit or express.
Браво колега. Страхотен клип! Адмирации за усилията.
Muy buen video, me ha servido de mucho... mi Delonghi magnifica E3000B a veces falla al ir a encenderla y tengo que insistir un rato en el botón de encendido... no se si con el tiempo tendré que cambiar todo el módulo de la botonera... sabes cual podría ser la causa?
1 saludo y gracias
Merci ce vidéo ma beaucoup aide 👍👍👍
Many thanks for this videos ! very useful !
+
Milen Stoitsev
Thabk you so much. Today i also had to refub mine boiler.
Thank you so much for posting these videos for fixing the Magnifica! Very helpful. Would you mind telling me a good resource for purchasing all the o-rings needed to refurbish my entire machine. I have developed a pretty big leak from my steam wand and i figure i should replace all o-rings while i have the machine already torn down. Thanks again for the help!
Hello I'm glad that my video was of help to you. I can recommend ebay
I also sell some parts for DeLonghi and Saeco.
Once I broke the first bolt, I decided not to open the boiler. Hope it does not leak
Milen, Your videos have been very helpful in maintaining my Rialto EAM 4500. I do have a new problem that I cannot find any information; When I push for hot water, I get a little steam and the pump runs for a second or two then the pump stops. Any suggestions? Thanks in advance. FYI I did replace the hot water solenoid which did not help the problem at all.
Hello, there is probably some blockage or a problem with the solenoid. When the water cannot flow freely the pressure rises and the pump muffle.
@@milenstoitsev6676 Thanks!
thank you verry much sir !!!!
Milen, I replaced the orings in my boiler. When I re-installed I make coffee but the coffee runs into the tray rather than through the diffuser. The warm up and ending rinse also go directly into the tray. I tried another diffuser but did not help. any suggestions?
I figured out my problem. I had to put a slightly smaller oring/gasket on the diffuser so it would move more freely.
Здравей, благодаря за полезното видео! Бойлера на моята машина е в почти същото състояние и аз скъсах двата болта в средата и смятам да правя същата процедура с пробиване и нова резба. Гледам, че са те питали за о-пръстените и си препоръчал И-бей. Има ли от къде да се закупят като цял комплект или по отделно всичките от България? Благодаря предварително!
Hellow.....my boiler screw is now brocken like youre ...where you buy this one? I searcherd on ebay and i find no one...thanks
Fantastic videos, do you have the part number for the main generator seal (when split) ?
Had purchase this guy with
www.ebay.co.uk/itm/DeLonghi-De-Longhi-EAM-kleiner-Dichtungssatz-für-Boiler-Durchlauferhitzer/260990447013?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649
Здравейте Милен
Гледам вашите видеа с голямо удоволствие а също и научавам много нови неща от тях .
Бих искал да ви попитам дали според вас може да се смени бойлер на делонги еам който е 900 или 1000 W с бойлер за esam който е 2×600 w и дали според вас е безопасно за кафе машината?
Благодаря ви предварително
Гено
Hi thanks for video, where do you buy delongi parts?
Hi, to clean the boiler, do you just clean with soapy water?
For organic pollution I use "CAFIZA2" or "PULY CAF PLUS" For scale bild-up "CALCINET" or "ASCOR"
Is it safe to submerge the whole thing? Will it affect the electrical components
@@koutuang9959 Yup , go ahead, but don't forget to let it dry... In general water and electronics is a bad combination, but in this case you have only heater terminals and wires, so it will be fine if you dry it, but rememver to wear some gloves, because this shit reacts with skin...
NOT EVEN WORTH REMANUFACTURING/refurbishing THIS PIECE!
Just spend 50-80 dollars on ebay for a new one, and replace. Seriously. this is not worth it when yours was as corrodded and leaky as mine was. I put a new generator in there, and it works like brand new again.
It's worth for me. For you it's 80bucks for me it's 480PLN=125,15USD. It's almost the same price for whole express. Seals I have for a couple PLN(from my firend), so it's worth for me compred to new unit or express.
hi speak like BORAT