This video will helped me. Thank you. I just have a question, where do I connect the fan, no or nc? And what type and how thick of wire do I use? Hope you'll kindly respond ASAP.
The relay works but the fan doesn't, when will you make a part 2 of this video where an actual fan is connected to it? I really need this ASAP. I hope you would kindly respond
Could you please make a part 2 where you'll comnect it to an actual fan. If you'll use a pwm 12 volt fan with 4 pins and if you do it this week, I'll subscribe to your channel.😊😊😊
I am having problem pike first time when u using voice module v3 to control motor it works and light is blinking but second time when i again run it the light becomes on not blink and then i have to train again please tell
Hello sir Sir i had make your project but i face a problem which is while train arduino it will respond time out while train why it so And i will arduino nano instead of arduino uno
sir can u please help me i am getting this error Baud rate: UNKONOWN Output IO Mode: UNKONOWN Pulse Width: 20ms Auto Load: enable Group control by external IO: UNKNOWN STATUS please help me sir i am very much sad
Bhaiya mera voice recognition kaam nhi kr rha😢 Voice train ho ja rha h lekin jb load ya record show krne ko bol rha to show kr rha untrained Please help bhaiya please
@@fairelectro i had done it....i input train 0 for the first voice....train 1 for second voice...and both show train success...but when i input " load 0 1 "....it show load success = 0....and record already in recognizer
Nice project
It's excellent sir 🤩🤩🤩🤩😲😲😲😲, Thank you very much Sir, could you explain the code, so that we can control more devices
Good day. Your video was very helpful. Just a question, how do you connect an actual fan and lightbulb to that?
connect light bulb and fan through relay module
This video will helped me. Thank you. I just have a question, where do I connect the fan, no or nc? And what type and how thick of wire do I use? Hope you'll kindly respond ASAP.
Connect Fan on ON pin of relay
The relay works but the fan doesn't, when will you make a part 2 of this video where an actual fan is connected to it? I really need this ASAP. I hope you would kindly respond
Could you please make a part 2 or something for this video where you are showing that you are connecting the relay to the actual fan and light...
I make video on this project as soon as possible.
Could you use a pwm 12 volt fan with 4 pins...if you do it this week, I'll subscribe to your channel.😊😊😊
Hi. Your video is good. However, would it work if I use a 12 volt fan?
Yes it will
Could you please make a part 2 where you'll comnect it to an actual fan. If you'll use a pwm 12 volt fan with 4 pins and if you do it this week, I'll subscribe to your channel.😊😊😊
I am having problem pike first time when u using voice module v3 to control motor it works and light is blinking but second time when i again run it the light becomes on not blink and then i have to train again please tell
Press reset button of Arduino then its working fine.
Hello sir
Sir i had make your project but i face a problem which is while train arduino it will respond time out while train why it so
And i will arduino nano instead of arduino uno
check wiring. and speaks two time while train
what type of fan should i use
sir now i will face redefination of void setup error before uploading . how to overcome this problem ??? please reply sir
Look your code, I think you re define void setup function in the code.
Where do you put the battery
it works with 5v. Connect +ive to Vin and -ive to GND of Arduino.
How do i connect the fan to the relay
Connect Ac live wire to COM pin of relay and Fan live wire to ON pin of relay.
Which company mic was that one you changed?
I replace mic with Boya M1 mic
सर मुझे ये प्रोजेक्ट खरीदना है
👏
sir can u please help me i am getting this error
Baud rate: UNKONOWN
Output IO Mode: UNKONOWN
Pulse Width: 20ms
Auto Load: enable
Group control by external IO: UNKNOWN STATUS
please help me sir i am very much sad
Bhaiya mera voice recognition kaam nhi kr rha😢
Voice train ho ja rha h lekin jb load ya record show krne ko bol rha to show kr rha untrained
Please help bhaiya please
awaz match ni ho ri ho gi. ak jesy hi dobara bolo
did you not load the train voice?
i had problem because when i tried to load the train voice...it say voice already in rexognizer and voice untrained..
set train record. for example . train 0, which store your voice on record 0. train 1, store your voice on record 1 and so on
@@fairelectro i had done it....i input train 0 for the first voice....train 1 for second voice...and both show train success...but when i input " load 0 1 "....it show load success = 0....and record already in recognizer
Sir please help me merko 8 channel wala banane ha help me
8 channel rely module laga len. jo b pins use karni han w code kar len
@@fairelectro pins code kase karu ye btado
@@fairelectroPlease bhaiya aap mujha code provide kardo na 8 channel ye phir 5,6 channel ka please 🥺