Thank you so much for this video. I started playing with the Settings and was upset because I couldn’t get the bike to go anywhere and with your video I got my bike back in order. Thank you so much.
Thank you so much, you are the best, your explanation is excellent, step by step, clear and it helped me just by listening to the video once. Thank you bro
Awesome video. I have the newer screen that comes on the Keteles K800. I also reached out to Keteles and they gave me the factory settings which pretty much mirrored yours. P01=003 (back light level) P02=000 (KMH or MPH) P03=048 (voltage) P04=010 (screen timeout 10 minutes) P05=005 (first number = when the motor helps 0 or 1, 5 = levels) P06=29.0 (tire size) P07=086 (? Not sure) P08=100 (speed limit in kmh) P09=000 (0 motor helps immediately when you peddle) P10=002 (0 is pedal assist only, no throttle, 1 is throttle only, 2 is both) P11=001 (sensitivity of peddle assist 1-24, 1 is the highest) P12=005 (intensity of power delivery 1-5, 1 is the most) P13=005 (number of magnets on crank sensor 5,8 or 12) P14=012 (max amp draw of controller) P15=38.0 (under voltage cutoff, 38v vs. 48v) P16=002 (cruise control, N/A on the Keteles bike) P17=001 (reset ODO, hold mode button and ODO returns to 0)
@@jackbenson9628 e8 reports throttle failure [ if you have one ]. this can be caused by a number of issues, be a loose throttle connection [ anywhere in the wiring of this throttle input ] or even the magnet in the throttle became unglued or a failure of the hall effect chip. [ these are inexpensive via manufacturer of bike or aliexpress ] now if you do not have a throttle control on your ebike, you should set the P010 configure to 0. [ no throttle ]. cheers
How you pass the code setted by seller to go on menu ? I have preinstaled code from dealer shop (C), and i cannot go on normal menu (P) . Know someoane ‘😢
Mine has no power to run the bike 🚲 and keeps saying earros thumb throttle dose not work and display doesn't work All the way to 20 Zero thumb throttle.
Just went and tried it for the first time...get most of it but find I can't take off up hill from a standing start as PAS doesn't kick in. Anyone any ideas how to set off uphill?
I don't know about the M5, but the M6 has a USB A port on the bottom. Pretty cool to charge your phone or use some USB powered device. But I don't think it can communicate over USB, only charge.
I wish I could remember, by default they come locked down to a slower speed. I think I had to hold the right to break handle while turning the bike on, it could’ve been the left, but I’m not not sure now, but after that, it was allowed to go full speed
Is there a way to reset the display to Factory Settings ? I pushed to much buttons...now (even when P10 is on 0 or 2) the pedal assist is not working anymore, when I put it on 1 for only throttle that works. Any help very much appreciated, it drives me crazy I can't figure out what's wrong 😞
That is a good question, because yours has additional configuration options, they may be out of order compared to mine. I would reach out to the manufacturer.
I've put about 25 miles on mine, and it's pretty fun. I'm about 190 and it cruises on slight up/down at about 30.5-31.5. I've had it to 34.8 as max speed. I was hoping to safely goose the speed, because I want to commute and the paved curvey hilly no shoulder 55mph road gets treated a bit like a race track. I work at night and that's worrisome from behind, 45 would be safer, not to mention shorten trip time. I don't want to fry anything, so the amp regulator should limit that, not allowing me to cook it if I set it for way too much and thermal detonator the battery pack. Wonder if a gel cooling wrap would help with that... Or a copper tube cage for a liquid chill...or I could spend another 1k on a different batter, lol.
If you want to explain anything, explain everything. How to get into bios. How to make adjustments once in bios. You explained the first, now explain the second. How to change from P1 to P2 etc.
Perhaps it may be productive to normalize the audio. You are rather quiet here. A little bit of audio processing would go a long way. Also, the long black screen (at 4:45) is less than ideal.
Thank you so much for taking it step by step and explaining everything so clearly!
Thank you so much for this video. I started playing with the Settings and was upset because I couldn’t get the bike to go anywhere and with your video I got my bike back in order. Thank you so much.
Thank you sir!! Got my settings fix by watching this video. You did great.
Thank you so much, you are the best, your explanation is excellent, step by step, clear and it helped me just by listening to the video once. Thank you bro
Thank you this has helped me immensely.
That was just what I needed thank you human
That was very helpful until the screen went black and the sound stopped at 4.48. Anyway, the best explanation I've found so far. Thank you.
ik heb het gedaan maar als ik hem dan bijvoorbeeld in z'n 50 zet gaat tie maar 25
Awesome video. I have the newer screen that comes on the Keteles K800. I also reached out to Keteles and they gave me the factory settings which pretty much mirrored yours.
P01=003 (back light level)
P02=000 (KMH or MPH)
P03=048 (voltage)
P04=010 (screen timeout 10 minutes)
P05=005 (first number = when the motor helps 0 or 1, 5 = levels)
P06=29.0 (tire size)
P07=086 (? Not sure)
P08=100 (speed limit in kmh)
P09=000 (0 motor helps immediately when you peddle)
P10=002 (0 is pedal assist only, no throttle, 1 is throttle only, 2 is both)
P11=001 (sensitivity of peddle assist 1-24, 1 is the highest)
P12=005 (intensity of power delivery 1-5, 1 is the most)
P13=005 (number of magnets on crank sensor 5,8 or 12)
P14=012 (max amp draw of controller)
P15=38.0 (under voltage cutoff, 38v vs. 48v)
P16=002 (cruise control, N/A on the Keteles bike)
P17=001 (reset ODO, hold mode button and ODO returns to 0)
Do you know how to fix error 8
@@jackbenson9628 e8 reports throttle failure [ if you have one ]. this can be caused by a number of issues, be a loose throttle connection [ anywhere in the wiring of this throttle input ] or even the magnet in the throttle became unglued or a failure of the hall effect chip. [ these are inexpensive via manufacturer of bike or aliexpress ] now if you do not have a throttle control on your ebike, you should set the P010 configure to 0. [ no throttle ]. cheers
How do i get the speed to work on the screen for the m5
My display is not saying how fast I’m going
How you pass the code setted by seller to go on menu ?
I have preinstaled code from dealer shop (C), and i cannot go on normal menu (P) . Know someoane ‘😢
Mines the same, any luck finding a password?
Nop , seems look , store who sell to me , change the code , and only they can make changes on sistem .
Sorry, I do not know
1801
999
When I set my bike to 5 power levels instead of the default 3 on P5, all 5 levels will make my bike go at full speed. Anyone knows why?
Mine has no power to run the bike 🚲 and keeps saying earros thumb throttle dose not work and display doesn't work All the way to 20 Zero thumb throttle.
Just went and tried it for the first time...get most of it but find I can't take off up hill from a standing start as PAS doesn't kick in. Anyone any ideas how to set off uphill?
Is there a video like this for the im j2?
How do you factory reset?
I don't know about the M5, but the M6 has a USB A port on the bottom. Pretty cool to charge your phone or use some USB powered device. But I don't think it can communicate over USB, only charge.
My battery has usb to charge phone
Do you know how to fix error eo8
Mine doesn't do that at all
my only goes to 03p on my dyu any idea why?
Вам удалось как то решить эту задачу? У меня такая же проблема.
If there a just given p1and p2, can I just disconnect a cable in the controller to make the bike faster?
I wish I could remember, by default they come locked down to a slower speed. I think I had to hold the right to break handle while turning the bike on, it could’ve been the left, but I’m not not sure now, but after that, it was allowed to go full speed
Is there a way to reset the display to Factory Settings ?
I pushed to much buttons...now (even when P10 is on 0 or 2) the pedal assist is not working anymore, when I put it on 1 for only throttle that works.
Any help very much appreciated, it drives me crazy I can't figure out what's wrong 😞
I am not aware of a way to factory reset, if you can just set the settings, the same as what I show.
serious question. Do you have to Hercules to unplug pin? I'm trying to replace my cracked screen 🙂
They are very challenging to unplug. Be careful not to break it.
@@chrisstinkering3651 Took it to a bike shop and got it replaced. Even the guy who unplugged it had to use his strength😃
Can't get my q20 1000 h throttle
Hi there does this works on a Swift pro 750w fat tire? My e-bike has the M5 display as well BUT it goes all the way to P20
That is a good question, because yours has additional configuration options, they may be out of order compared to mine. I would reach out to the manufacturer.
Was looking to get this bike but there are no reviews of it.
Would you recommend it? and what's it's top speed?
I would recommend this bike. It’s been a lot of fun. TopSpeed is about 35 mph.
I've put about 25 miles on mine, and it's pretty fun. I'm about 190 and it cruises on slight up/down at about 30.5-31.5. I've had it to 34.8 as max speed. I was hoping to safely goose the speed, because I want to commute and the paved curvey hilly no shoulder 55mph road gets treated a bit like a race track. I work at night and that's worrisome from behind, 45 would be safer, not to mention shorten trip time. I don't want to fry anything, so the amp regulator should limit that, not allowing me to cook it if I set it for way too much and thermal detonator the battery pack. Wonder if a gel cooling wrap would help with that... Or a copper tube cage for a liquid chill...or I could spend another 1k on a different batter, lol.
If you want to explain anything, explain everything. How to get into bios. How to make adjustments once in bios. You explained the first, now explain the second. How to change from P1 to P2 etc.
Sorry, I’m not sure what you mean regarding P1 to P2
Get into this mode by holding the UP and DOWN buttons until you enter into this mode. Press the middle M button to cycle between P1, P2, P3, etc.
I like the part after 4:45.
Jokes aside good video tho
Perhaps it may be productive to normalize the audio. You are rather quiet here. A little bit of audio processing would go a long way. Also, the long black screen (at 4:45) is less than ideal.
Thanks! I didn't realize the video had the black screen at the end. I'll look into the audio.
you should get a lapel mic, you are a very soft talker.
Ha ha, I agree. And this was coming from a recording, using a headset after the fact.
Thankyou
Do you know how to fix err10 message
Sorry I do not
Did you fix this ?
No err10 message