this has been really helpful. me and my brother are planning on tearing down and rebulding a 1985 quadrunner. your videos have helped me get a little bit of knowledge that will be helpful for tearing it down.
Love it. Thanks for sending the message and for watching. Have you subscribed? Let us now if you need parts for the rebuild: ebay.com/str/midnebraskamotorsports
When freeing a siezed piston and rings, soak the rings with liquid penitrent as long as possible then, use a pc of wood to drive the piston, then you will be able to reuse your parts and save money. Use wood to drive parts apart. Also another tip for folks is to use a pc of cardboard with a drawing to put your bolts in to keep the lengths in the correct hole. Take your time and enjoy your work. Good luck.
Can you please explain how to change the timing chain? Do you have to to a full case split or just the side cover? Your video is perfect, and you stopped right at the point to where I thought you were gonna remove the chain. My chain has a lot of slop. Do I have to change it or will the 2 tensioners take up any slack it would have? Please let me know.
Can I take the top end off to replace piston without removing the entire assembly on the quad 300? It looks exactly the same as the motor in your video. But mine has electric start.
Assembly of top end would be interesting, but my immediate need ia how to time cam. Inspection port mark and lifters on heal of cam. I have a manual but can't find any description of that in it.
Hey man, I just bought a 1987 LT250 Quad Runner. It only has 500 miles on it and runs great. The only this is, when it gets warmed up it begins to make a squealing noise. At first I thought it might be a small hole in the muffler, but now I am thinking CVT or one way joint. Any thoughts? Thanks!
You don't normally have to go that far down just to put a fresh head piston i hope not lol i may have to put a head on my dads lt2504wd it smokes only hot
You have to think you've got the cup for the pull start laying in front of you all you had to do sliding onto the end of the crank and you could have used a screwdriver and spun that engine around. 😄
![Ice On My Teeth - ATEEZ エイティーズ 에이티즈 [Music Bank] | KBS WORLD TV 241115](http://i.ytimg.com/vi/c-n92OgbbwA/mqdefault.jpg)
this has been really helpful. me and my brother are planning on tearing down and rebulding a 1985 quadrunner. your videos have helped me get a little bit of knowledge that will be helpful for tearing it down.
Love it. Thanks for sending the message and for watching. Have you subscribed? Let us now if you need parts for the rebuild: ebay.com/str/midnebraskamotorsports
This video is an educational video on what a backyard butcher mechanic is!
Exactly!! I'm glad I'm not the only one that can see it!!
Bet it ran great after
When freeing a siezed piston and rings, soak the rings with liquid penitrent as long as possible then, use a pc of wood to drive the piston, then you will be able to reuse your parts and save money.
Use wood to drive parts apart.
Also another tip for folks is to use a pc of cardboard with a drawing to put your bolts in to keep the lengths in the correct hole.
Take your time and enjoy your work.
Good luck.
Nice break down bro, thank you. Do you have a video of re-assembly?
Im redoing transmission on 95 250 i followed your direction so far im now doing reassembly and video
Can you please explain how to change the timing chain? Do you have to to a full case split or just the side cover? Your video is perfect, and you stopped right at the point to where I thought you were gonna remove the chain. My chain has a lot of slop. Do I have to change it or will the 2 tensioners take up any slack it would have? Please let me know.
Do you have the rest of the video posted for splitting the case? And removing crank etc?
Hi! Is part 2 of this video uploaded and available?
Im having a problem with my quad not driving after shifting, the neutral light goes away like its in gear but no movement... any ideas?
Hey I was wondering if you’d be able to tell me how to torque the center nut on the clutch pack
Where can I find that puller you are using
So will the motor Turn if I put it in gear before disassembly?
Great Video what MM size is the flywheel puller?
Can I take the top end off to replace piston without removing the entire assembly on the quad 300? It looks exactly the same as the motor in your video. But mine has electric start.
@@MidNebraskaMotorsports got here just in time. About to tackle this job
Assembly of top end would be interesting, but my immediate need ia how to time cam. Inspection port mark
and lifters on heal of cam. I have a manual but can't find any description of that in it.
Hey man, I just bought a 1987 LT250 Quad Runner. It only has 500 miles on it and runs great. The only this is, when it gets warmed up it begins to make a squealing noise. At first I thought it might be a small hole in the muffler, but now I am thinking CVT or one way joint. Any thoughts? Thanks!
this has gears. no cvt
head gasket or valve cover gasket you think
What part number is the flywheel puller if it has a part number
Thanks for the question Ryan. Link to puller is here: www.ebay.com/itm/333404367710 Let us know if you need anything else.
Thank you man I ordered it the other day thanks for your reply back
Do you know where i could find all the trouqe specs or know the ones for the head bolts
Is the transmission the same on a 300 as the 250?
i got the same engine mine is smoking bad around the cylinder head when engine gets hot. please help
You don't normally have to go that far down just to put a fresh head piston i hope not lol i may have to put a head on my dads lt2504wd it smokes only hot
When are you going to make a video of you putting it back together you said you rebelled it you only took it apart
shouldn't you of cleaned the motor off first and drained the oil? Your pretty rough lol did it ever run again? wheres part 2?
I totally agree. This video should be titled "back yard butcher shows you what not to do"!!
Where is part two?
Where is part two. Where are you tossing all the bolts? How do you know where they all go on rebuild? Usually some are different lengths.
@@elkskiutah8204 still no part 2. Its like leaving a child in a pool of snakes. Dude, post part 2!
There is no part 2 because the engine never ran again.
I'd hate to be that customer that gets his motor banged on the piston prob broke as u hammered on it
You have to think you've got the cup for the pull start laying in front of you all you had to do sliding onto the end of the crank and you could have used a screwdriver and spun that engine around. 😄
I don't see any rebuild only tear up things i can do that to
Mines a 86 🤦🏾🤦🏾🤦🏾🤦🏾