I’m so happy I found these videos. The man speaking was one of my teachers at mobile electronics training. Very smart guy. Wish I could remember his name. Always been a fan of Rockford Fosgate
I bought a T1000.1bdcp amp to replace my Audio Control LC1.800. The Fosgate really makes my Image Dynamics subs come to life. Much more output through constant controlled power. Easily my favorite amp. Clean and stupid powerful.
I'm excited. To be getting a full Rockford Fosgate System put in my 2005 Suburban. 1- Power T400 x4 channel Amp. 1-Power T1000 2 channel Amp. 4- P1650 6.5 Coaxial for Front and Rear Door Speakers. 4- P1TS Tweeters for A and B pillars. 1- P132 3.5 speakers for the D pillar. 2-P3 12" woofers in ported box. Cant wait to hear it.
I'm very impressed with my 1500.1 Power amplifier! I've had it for 1 year and only ran it at 4 ohms and it pushes my P3's to the max. And my 400.4 Power is nothing to squeeze at on my highs and mins. Never once has either ran hot or shut down.
We're actually doing a complete JEEP GLADIATOR installation designed for Rockford Fosgate Dealers at MASTER TECH EXPO and is OPEN TO THE PUBLIC. Guest passes are available at www.mastertechexpo.com
Hi I would like to know what's the difference between a T2500-1bd amp and a T2500-1bdcp amp, maybe I missed it when to talked about it in this video!!! I have one of each of those amps!!! Does one put out more power than the other or do they both put out the same amount of power??? Thank You!!!
Great Question Jose, The CP version incorporates our Patented Constant Power technology. It helps the amplifier sustain power during varying impedance fluctuations cased by the speaker/subwoofer for more consistent delivery of power output. If comparing both amplifiers for a certain amount of time (Say a music track if 1:40 mins) the CP version will produce more energy, consistently over the entire duration of the 1:40 music track. One thing to note is we don’t recommend using the bdSync cable to bridge these 2 different amplifiers together.
@@rockfordfosgate So that means if you want to use the bdsync cable to strap two of them together they have to be two bdcp amps or two bd amps of the same kind is that correct for it to work??? If that's the case then thank you for that piece of information!!! My question is why can't they be two different kinds???
@@josea.garcia3994 That is correct, for optimum performance, they should both be “bd” or both “bdCP”. We recommend they be the same because otherwise it would be like strapping 2 cars together, one uses the accelerator and the other uses cruise control. For flat straight-a-ways, it will work fine, but for off-road use (similar to a speaker’s complex impedance curve) one car will fluctuate the throttle to maintain constant control, while the other is being manually manipulated, so both engines will not be in “sync” with each other.
@@rockfordfosgate Great that's good to know!!! So strapping two of the same weather it be two bd amps or two bdcp's would they both come out to being 6000watts strapped together or can the final wattage very in every different sound system set-up???
@@josea.garcia3994 Two amplifiers in bdSYNC mode will produce 5,000 Watts x 1 @ 2-Ohm. Please note, the individual amplifier minimum impedance is 1Ω, but when bridging, the minimum impedance is 2Ω.
Hey rockford team i have a question on the bdcp amps the settings knobs have a small dot is that the mark to go by???? i noticed the knobs are kind diffrent than other amps .
No, the dots are there just for reference, not where you should be setting them. The CROSSOVER is typically set to 80Hz Low-Pass for subwoofer systems and the GAIN should be matched to your source unit or preamplifier output. If you're having problems setting your gains, you can refer to this section "GOOD: SET YOUR GAINS BY EAR" in this article: How To Properly Set Your Gains: rftech.custhelp.com/app/answers/detail/a_id/46/
On the T600-4 amp, using the the Punch EQ, if you have the front channel set to High-Pass and rear channel to Low-Pass will both channel pairs raise at the same rate in their respective frequencies as described with just setting it to the the same cross-over across the board? ... I have had this amp since 2008 and has outlasted all of my cars to this date never installed a punch knob on it. I love my Power Series Amplifiers. (T600-4, T2500-1bdcp, T500X1PBR) ... That does not take away from my Prime and Punch Amps ... Power Series just hits a little different. 💪🏾
Hi Juan, great question on a great amplifier! When using the Punch EQ, it can add up to +12dB @ 12kHz (Treble) and up to +18dB @ 45Hz (Bass) depending on where the adjustment is set. When the crossover is set to LP (low-pass) the EQ boosts BASS response. When the crossover is set to HP (high-pass) the EQ boosts TREBLE response. We have a diagram on how it works here: rftech.custhelp.com/app/answers/detail/a_id/918/
Rockford Fosgate I am familiar with the Bi-Amp advisory. However, the referenced diagram does not address the 4 channel amplifiers with a single PEQ knob. Does it imply that both crossovers in the 4 channel amp will simultaneously respond? My guess is that it does ... I’m guessing that the downside of using a 4-channel with a single PEQ know, each channel will respond to the knob’s setting and their is no way to isolate the two unless you get two separate amplifiers. ... I am using the front channels for tweeters (High-Pass) and the rear channel for my mids (All Pass) on my front stage set-up (full active w/ 3Sixty.3 DSP). I’ll test it out in the lab and see when I get time. Thanks for the feedback!
@@PhiMobileSounds Thank you for the clarification. The T600-4 amplifier does feature 2 Punch EQ settings that allow the front & rear settings to be adjusted independently. However, when plugging in the Remote Controlled Punch EQ knob, this overrides REAR channel's built-in Punch EQ setting, because the rear channels are typically bridged for subwoofers and the front channels typically run mids/tweets.
Great question Jameson! How many subwoofers are you planning to use? If just one, then use the T2S1-13 model since it would be a 1-ohm load and perfectly matched for the Power Series mono amplifiers. Since the power handling is rated at 2,000 Watts RMS, we would suggest the T1500-1bdCP. Although it's rated to produce 1,500 Watts x 1 @ 1-Ohm, its dynamic power is actually 1,715 Watts x 1. This is under the rated power handling of the subwoofer and a perfect match!
So the subwoofer is rated to handle up to 750 Watts, correct? Since it's a 2-ohm DVC subwoofer, it can be wired to create a 1-ohm load or a 4-ohm load. The T600-2 amplifier is designed to produce 600 Watts x 1 @ 4-Ohm Bridged. Look at the WiringWizard tab on our T600-2 Product Details Page and use Wiring Diagram #2 at: www.rockfordfosgate.com/products/details/t600-2
Rockford Fosgate Thank you it can be heard a block away this one bad mother it isn't very big but man it Packs a Punch the gain is up a notch , who would have thought. Rockford Fan 4 Life.!!!!!!!! it sounds way better than a set of 12's. #No doubt. It's a little Monster.!!!!! 98 Honda Passport is a Beast and competing with a Yukon or a Tahoe. Much love Happy Camper.!!!!
Currently running t2652-s components front and rear t1650 coaxial with p400×4 amplifier. what amplifier would u recommend for best sound quality and loudness to get out of the speakers since they are only being fed 50rms
Hi Eloscar 57, Thanks for using Rockford Fosgate for your ride! Both those are amazing SQ speakers. Right off the top, these look like an awesome match! So, let's breakdown what you have: • The T2652-S are rated to handle 100 Watts RMS • The T1650 is rated to handle 75 Watts RMS • The Punch P400X4 Continuous Power is 50 Watts x 4 @ 4-Ohm and Dynamic Power is 82 Watts x 4 @ 4-Ohm The Punch P400X4 is a great Class-A/B amplifier designed for SQ and exactly what you want to match with your SQ speakers. The power output matchup between the amplifier and speakers couldn't get any better. As you know, Rockford Fosgate amplifier are typically considered "under-rated", so you can easily expect the Dynamic Power output from the amp. If it's not loud enough, you may need to start looking at adding multiple drivers to increase your SPL output. Otherwise, this must sound amazing.
Hi RF I know this video is old but can I use the T400-2 for tweeters, using the power T2 components and want to go active. I hope I get a reply. Thanks
HI Neelchand, the Power T400-2 is rated to produce 120 Watts x 2 @ 4-Ohm (dynamic power is 145W x 2). The T2652-S is rated to handle up to 100 Watts RMS, so technically this amplifier will overpower the T2 components, so we advise caution or using a slightly lower powered amplifier.
HI Bryce, I answered the same question you posted on another video here: ruclips.net/video/Il--ghOK6iM/видео.html&lc=z22whtjbolr5vlyrr04t1aokgwd0vrtyeo1jfsuwe0ywbk0h00410
The amplifier will produce less output and/or go into protection mode. Running the amplifier below the recommended impedance isn't going to get you more output.
The T600-4 amplifier is rated to produce 100 Watts x 4 @ 4-Ohm or 150 Watts x 4 @ 2-Ohm. Dynamic power output is 139 Watts x 2 @ 4-Ohms or 236 Watts x 2 @ 2-Ohms. The T1692 speakers are rated to handle 100 Watts RMS, so this will be a great matching amplifier. Since the T600-4 is rated to produce 300 Watts @ 4-Ohm Bridged, this will be adequate for 1 or 2 subwoofers. This is a Sound Quality amplifier so the bass will be accurately reproduced assuming the correct enclosure is designed for the subwoofers. However, if you are looking for MONSTER bass (like you only listen with the volume at 11 out of 10), you may want to step up to a dedicated mono amplifier. The T500-1bdCP is a good starting point.
@@JBrain58 You're welcome! We also have live techs during 8am-5pm (Arizona) business hours. You'll see live chat at the bottom of our website at rockfordfosgate.com when they are online, or you can always call at 1-800-669-9899 and just talk with them about other scenarios you're looking at. Thanks for help saving the world from bad car audio, one fanatic at a time! 👍
I have got a power t1000-1bdcp amp to fit, however space is tight. Will it be OK to mount this amp to the back of my dual 12" p2 subwoofer box? I know its not ideal because of the vibrations
@@rockfordfosgate I was thinking of mounting the amp with a sheet of rubber between to dampen out the vibrations. Thanks for the reply. I will have a rethink to see if I can squeeze it on the back of the rear seats where I have my t800-4ad mounted.
I'm running my bdcp1000 at 1 ohm on 2 T1 12s and they beat them to death the t1500 bdcp was a bit much for my car to handle the 1000 puts out 1500+ watts and dynamically i would expect in the 2k range. When I buy a 1000 watt power series RF amplifier I expect more than 1000 watts and according to my birthsheet its over 1400 at 2 ohms and over 1500 at 1 ohm. My 1500bdcp does over 2000 watts at one ohm and big d got 3200 dynamically.
@@justinkelsey9218 yeah I ended up getting the t1000 on the p3s birthsheet was 1525 at 1 ohm....thing beats insaaaaaane. Sounds crazy in my 2019 suburu impreza
I got a prime 750 on 4 4ohm svc 8s they handle only 200 watts they do good on the amp but should I have went with the punch 500 what would be the difference
The differences between these two amplifiers were taken from their spec pages: PRIME R750-1D 250 Watts x 1 @ 4-Ohm 500 Watts x 1 @ 2-Ohm 750 Watts x 1 @ 1-Ohm PUNCH P500X1bd 150 Watts x 1 @ 4-Ohm 300 Watts x 1 @ 2-Ohm 500 Watts x 1 @ 1-Ohm
I have a 1500bdcp I'm going to run one sub don't know Wich one yet but should I run the amp at 1ohm or 2 ohm what ohm is better and is there a difference on this amp
Although the Power T1500-1bdCP is rated at 1,500W at 2-ohm and 1-ohm, Dynamic Power is rated at 1,549 Watts x 1 @ 2-Ohms and 1,715 Watts x 1 @ 1-Ohm. The amplifier produces the best possible power output at 1-ohm, so you just want to make sure the subwoofer's RMS Power Rating will handle that amount of output power.
@@rockfordfosgate I see people saying running amp at 1ohm makes the sub have not as good performance and the amp won't last as long I have no problem running at 2 or 1 ohm..only if 1ohm If it doesn't ruin the amp..just trying to figure out what ohm is best overall thanks so much
@@jeffeisenzapf4131 The Power T1500-1bdCP is specifically designed to operate at 1-Ohm or higher. Many "armchair-technicians" love to talk others into lower impedances like 1/2 ohm thinking you get more power from the amplifier, which is not necessarily true. I'm glad the advice you read is error'ing on the safer side. The amplifier will work just fine at 1-ohm.
Hi, I have a question, I have the amp t-1000.1bd and I want to connect 3 subwoofers 4ohms each, so the impedance will be 2.67 ohms. The amp will be working fine???
I am thinking to buy a single P3D4 12 @ 4 ohms connected to T500BDCP. 2 ohm load. Is this configration correct? Will my amp t500bdcp shut down after excessive usage for one or two hours or even more?
We run true Dynamic Power tests against Rockford Fosgate amplifiers. Assuming you're referring to the Power T2500-1bdCP? It's Dynamic Power numbers can be found under the SPECIFICATIONS tab on our website: www.rockfordfosgate.com/products/details/t2500-1bdcp/ T2500-1bdCP Dynamic Power 1823 Watts x 1 @ 4-Ohm 2940 Watts x 1 @ 2-Ohm 2980 Watts x 1 @ 1-Ohm
I was talking about clamping in a car. The way you have the sub in a car will change the ohm level. If I use this T2500, it should clamp 2940 watts in the car cause my ohm level moved up to 2 ohms from 1 ohm. and 2 ohms is about the same as 1 ohm on this T2500. If this will happen, this is the best amp technology out there. And i am a believer. And will buy this amp. I would love to see real wattage in the car.
The Constant Power technology inside the T2500-1bdCP is pretty amazing! You can learn more about CP and how it works here: ruclips.net/video/7EP4-4TMWFw/видео.html Regarding "clamping" ... not 100% sure what you're referring to because the impedance plot of a subwoofer/enclosure is very complex. In addition, the effect on the amplifier is complex as well (see the Constant Power video above.) It's not a cut and dry 1-ohm/2-ohm equation. The Dynamic Power tests we use at Rockford Fosgate are NOT based on simple resistive loads, because loudspeakers (subwoofers) consist of capacitive, inductive, as well as resistive loads. The Dynamic Power data we publish is considered "real world" to what is capable in the vehicle. I wouldn't read too much into forums that weigh heavily on "clamping" and "box rise". There are simple factors like charging system voltage, proper grounding, and current reserve (energy storage capacitors) that have a much larger effect on amplifier power than those factors.
I am debating between the p600x4 and the t400x4ad to run 4 of my door speakers i’m not sure which one to go with. My front speakers are 80rms and rear is 55rms, i know “power” wise that the Punch should be good but i hear the Power amps just sound better. Anyone have any ideas?
Hi Francisco, the main difference between the Punch and Power in this regard is the slight power differences and the circuit topology. The Punch model use Class-AB (sound quality) and the Power uses Class-AD (class-d). You'll have better sound quality with the Punch model, but the Power amp provides similar power in a compact package. If you have the room, use the Punch model. If you're tight on space, use the Power model. Here's a quick overview of the specs: • P600X4 ($399.99): 75 Watts x 4 @ 4-Ohm / 150 Watts x 4 @ 2-Ohm / 300 Watts x 2 @ 4-Ohm Bridged • T400X4ad ($439.99): 100 Watts x 4 @ 4-Ohm / 100 Watts x 4 @ 2-Ohm / 200 Watts x 2 @ 4-Ohm Bridged
I'm planning to buy two JBL CX Series 12" single voice coil 4-Ohm subwoofers for black friday, which amp do you recommend for my 2015 gmc sierra 1500 crew cab, by the way I'm planning on keeping my BOSE speakers for the highs
Hi Juan, the JBL CX Series 12" are rated to handle up to 250 Watts RMS each, so two subwoofers would give you 500W Power Handling and can be wired in parallel to create a 2-ohm load. If you're looking for just a mono subwoofer amplifier, you could use the Prime R500X1D since it's rated to produce 500 Watts x 1 @ 2-Ohms. However, I caution you if you love to hammer your system... that amplifier can produce up to 647 Watts which would over power your system. If you're looking for a multi-channel amplifier to also run the mids & highs, we'll need to see what the RMS power handling is on the speakers, so without knowing, you could use either the Power T1000-4ad (250W x 2 @ 4-Ohm for the stereo channels and 500W @ 2-Ohm Bridged for the sub) or the T600-4 (100W x 2 @ 4-Ohm for the stereo channels and 300W @ 4-Ohm Bridged for the sub.)
That's a great amplifier! Be careful when setting up the gains for your tweeters and midrange because it's one mighty powerful amplifier. Just want to make sure your system lasts for a very long time. You may want to setup the Gain Overlap at 0dB for those speakers.
I'm kind of confused because you first mentioned the JBL CX1200 12" woofers I'm trying to get handle up to 250 watts RMS each but on the description it says 1,000 peak power each, or am I being understood between RMS and peak power?
I agree it's confusing. If you can't find the certified power ratings (CEA-2016 for amps and CES-2031 for speakers) then always use the RMS Power Ratings. "Peak Power" or "Max Power" ratings are usually just double or quadruple the RMS ratings to represent "this product can handle this power for a few milliseconds". As mentioned earlier, the Power T1000-4ad will be great using the rear bridged channels for the subs and will generate 500W for both subwoofers (250+250=500). I'm just suggesting to use caution on the front channels because you'll be delivering 100W to the left and right sides, so check the power rating of your tweeters & midrange. To be safe, set the gains on the front channels to 0dB Gain Overlap so you don't over drive them.
I have a (2007 year made) rockford fosgate p500 1bd and I have 2 punch 2007(year made) p3sd410 can I conect them to 1ohm with this amp or this subwoofers??
@@mikemorales5361 Ah, the Punch P500-1bd. Yes, it's also designed for a 1-ohm load. You can find the owner's manual here: rftech.custhelp.com/app/answers/detail/a_id/865/
@@rockfordfosgate great now i know I can run this amp at 1ohm. But M'I in a safe zone to run the 2 punch p3sd410 that I bought back in 2007 without burn them??
Hi Kevin, sounds like you may have the 12W6v3-D4 or the 12W6v2-D4 and they are rated to handle 600 Watts RMS. They don't necessarily "need" 500W, but typically a subwoofer like this works great from 30% RMS up to the RMS power rating (150W - 600W). Since you have 3 of the dual 4-Ohm voice coils, they can be wired to create either a 6-Ohm or 2.67-Ohm load and have a total power handling capacity of 1800 Watts (we'll assume you'll wire them to create a 2.67-Ohm load.) A great amplifier is the Power T1500-1bdCP. It's rated to produce 1500 Watts x 1 at both 1-Ohm & 2-Ohm loads due to its "Constant Power" technology. We don't have power ratings at 2.67-Ohms since it's an odd impedance, but under Dynamic Power conditions (real world) it can produce up to 1549 Watts x 1 @ 2-Ohms. This is PERFECT to power these subwoofers without exceeding their power limitations. Here's a handy link to that amplifier: Power T1500-1bdCP www.rockfordfosgate.com/products/details/t1500-1bdcp
Sounds great Kevin! If you need any assistance setting up the amplifier, feel free to give our tech's a call at 1-800-669-9899. They'll be happy to clarify any questions you may have.
There's nothing wrong with the amplifier. Our MEHSA technology moves the heat away from the MOSFET more efficiently away to the heatsink like NO OTHER amplifier on the market. The heatsink is doing exactly what it's designed to do, dissipate heat. Look at this video at timecode 01:55 where we describe what MEHSA does for the cooling effect.
There are several Power Series amplifiers discussed in the video, but we suggest matching the RMS power handling of the subwoofer with at least the RMS power of the amplifier, preferably the Dynamic Power. The point is not to exceed the RMS power handling of the subwoofer.
O.K. great! The P3SD4-10 is rated to handle 300 Watts RMS, so two subwoofers will give you 600W total power handling capacity. These 4-ohm DVC models can be wired to create a 1-ohm or 4-ohm load. There are several options, you could use a single amplifier like the P1000X5, or use two amplifiers like the P500X1bd for the subs and the P400X4 for the front components & rear coax.
Great! Our only suggestion is be careful with the P1000X2. That is a powerful amplifier and it will most certainly be feeding nearly double the power those 2 subwoofers can handle, especially being "shallow". Good news is ... this future-proofs your setup if you to upgrade to the Power T1 slim subwoofers as they respond more like a traditional subwoofer and have higher power handling capacity.
No Rockford Fosgate amplifier - old or new - is recommended to run below the recommended impedance as stated in the owner's manual. 0.5 Ohm daily is not recommended. This is because "Box Rise" is not a constant, and therefore can cause dangerous low impedance conditions for the amplifier, running it harder and shorten the life expectancy of the electronics.
I wired my sub to rockford t2500bdcp to 0.5 ohm, I checked many frequencies and my lowest box rise was 1.1 ohm . Rockford recommendation is 300 ampere external fuse for t2500bdcp and when I played 33 hertz tune and the box rise was 1.1 ohm my external fuse is blown. Rockford says that on 1 ohm load this amp will give me the same power that on 2 ohms, but if i wire my sub to 1ohm load there is always will be more than 1 ohm because of box rise
What do I set my gains on my T600.2 I bought it used the gain was set at 5, The EQ was set at 125, and the Hertz was set for 60 Hertz . I'm putting it to push a SA 15 2 ohm dvc are those gains setting good. should I leave it alone. please let me know what to set it at for 1 SA 15.
Hi Gz, the Power T600-2 amplifier gains should be set to match the source unit. We have an article on setting gains here: "How to Properly Set Your Gains" rftech.custhelp.com/app/answers/detail/a_id/46 . For the crossover, I would personally set it to 80Hz since a lot of bass comes from the 50-60Hz region (the current crossover setting is set to -24dB at 60Hz so you're losing lots of bass).
so why 80 Hertz? and my eq is set to 124 on the amp and my gain at 5 . what do I set the eq on the amp? and why 80 Hertz if I'm losing alot of bass. my unit is is set at zero and natural sound I got bass blockers on my highs it's a pioneer head unit.
Did you have time to review the tutorial on Setting Gains? It explains how to adjust your gains with and without an equalizer, regardless of the source unit being used. The crossover frequency is just a recommendation, but as mentioned earlier, the current crossover setting is set to -24dB at 60Hz (it doesn't "start" at 60Hz) so you're potentially losing a lot of bass if you like the hard-hitting frequencies that typically reside at 50-60Hz. We also have an article on crossovers if you need more information on how they work here: rftech.custhelp.com/app/answers/detail/a_id/68
Hi Jose, the Power T1500-1bdCP is a great amplifier and is rated to produce 1500 Watts x 1 @ 1-Ohm but can dynamically produce 1715 Watts x 1 @ 1-Ohm. The following woofer combinations give you at least 1500 Watts of power handling capacity: (1) 2Ω SVC Woofer to create a 1Ω load: • T2S1-13 - Power 13" T2 Single 1-Ohm Subwoofer • T2S1-16 - Power 16" T2 Single 1-Ohm Subwoofer • T3S1-19 - Power 19" T3 Single 1-Ohm Superwoofer (2) 2Ω SVC Woofers to create a 1Ω load: • T2S2-13 - Power 13" T2 Single 2-Ohm Subwoofer • T2S2-16 - Power 16" T2 Single 2-Ohm Subwoofer • T3S2-19 - Power 19" T3 Single 2-Ohm Superwoofer (4) 1Ω SVC Woofers to create a 1Ω load: • T2S1-13 - Power 13" T2 Single 1-Ohm Subwoofer • T2S1-16 - Power 16" T2 Single 1-Ohm Subwoofer • T3S1-19 - Power 19" T3 Single 1-Ohm Superwoofer (4) 2Ω DVC Woofers to create a 1Ω load: • P2D2-12 - Punch 12" P2 2-Ohm DVC Subwoofer • P2D2-15 - Punch 15" P2 2-Ohm DVC Subwoofer • P3D2-10 - Punch 10" P3 2-Ohm DVC Subwoofer • P3D2-12 - Punch 12" P3 2-Ohm DVC Subwoofer • P3D2-15 - Punch 15" P3 2-Ohm DVC Subwoofer • T1D215 - Power 15" T1 2-Ohm DVC Subwoofer
@rockfordfosgate they definitely do that. There's just little different about a RF amp and when you know you know. I guess maybe that dynamic power . I own other amps but they just ain't the same.
@@rockfordfosgate My t600-4 has arrived as well as my 8 pps4 6.5 midrange drivers. Will wiring 2 sets individually to each channel create the 2 ohm load? Or do i have to bridge them?
@@victorl147 Wiring two 4Ω midrange in parallel will create a 2Ω amplifier load. YOu can use our Woofer WiringWizard for illustrations on how to wire here: www.rockfordfosgate.com/support/wiring-wizard/
I’m so happy I found these videos. The man speaking was one of my teachers at mobile electronics training. Very smart guy. Wish I could remember his name. Always been a fan of Rockford Fosgate
Thanks for being a Rockford Fosgate Fanatic! The instructor in this video was Rico Felice.
I bought a T1000.1bdcp amp to replace my Audio Control LC1.800. The Fosgate really makes my Image Dynamics subs come to life. Much more output through constant controlled power. Easily my favorite amp. Clean and stupid powerful.
Thanks for the great feedback on your experience with the Power T1000-1bdCP! Glad your system is rockin’ even louder now!
I'm excited. To be getting a full Rockford Fosgate System put in my 2005 Suburban. 1- Power T400 x4 channel Amp. 1-Power T1000 2 channel Amp. 4- P1650 6.5 Coaxial for Front and Rear Door Speakers. 4- P1TS Tweeters for A and B pillars. 1- P132 3.5 speakers for the D pillar. 2-P3 12" woofers in ported box. Cant wait to hear it.
Wow Harvey, your plan for a 1,400 Watt system sounds like it's gonna rock the neighborhood. Thanks for being a Rockford Fosgate fanatic!
I'm very impressed with my 1500.1 Power amplifier! I've had it for 1 year and only ran it at 4 ohms and it pushes my P3's to the max. And my 400.4 Power is nothing to squeeze at on my highs and mins. Never once has either ran hot or shut down.
Hey bunky021543, we're thrilled those Power T1500-1bd & T400-4 amplifiers are working great in your system! Appreciate your feedback!
You're welcome and thank you all for making such awesome products!
i wish fosgate held classes for the public
We're actually doing a complete JEEP GLADIATOR installation designed for Rockford Fosgate Dealers at MASTER TECH EXPO and is OPEN TO THE PUBLIC. Guest passes are available at www.mastertechexpo.com
Great AD vs BD explanation
Appreciate your feedback!
I LOVE ROCKFORD FOSGATE AMPS, THEY PUSH MY 15s To The Limit
Thanks Dizizope for your testimonial and being a #Fanatic!
What 15s u have
Can you bridge the rear two channels and leave the front two as separate channels to allow for a subwoofer on any of the 4channel amps you supply
Hi I would like to know what's the difference between a T2500-1bd amp and a T2500-1bdcp amp, maybe I missed it when to talked about it in this video!!! I have one of each of those amps!!! Does one put out more power than the other or do they both put out the same amount of power??? Thank You!!!
Great Question Jose,
The CP version incorporates our Patented Constant Power technology. It helps the amplifier sustain power during varying impedance fluctuations cased by the speaker/subwoofer for more consistent delivery of power output. If comparing both amplifiers for a certain amount of time (Say a music track if 1:40 mins) the CP version will produce more energy, consistently over the entire duration of the 1:40 music track. One thing to note is we don’t recommend using the bdSync cable to bridge these 2 different amplifiers together.
@@rockfordfosgate So that means if you want to use the bdsync cable to strap two of them together they have to be two bdcp amps or two bd amps of the same kind is that correct for it to work??? If that's the case then thank you for that piece of information!!! My question is why can't they be two different kinds???
@@josea.garcia3994 That is correct, for optimum performance, they should both be “bd” or both “bdCP”. We recommend they be the same because otherwise it would be like strapping 2 cars together, one uses the accelerator and the other uses cruise control. For flat straight-a-ways, it will work fine, but for off-road use (similar to a speaker’s complex impedance curve) one car will fluctuate the throttle to maintain constant control, while the other is being manually manipulated, so both engines will not be in “sync” with each other.
@@rockfordfosgate Great that's good to know!!! So strapping two of the same weather it be two bd amps or two bdcp's would they both come out to being 6000watts strapped together or can the final wattage very in every different sound system set-up???
@@josea.garcia3994 Two amplifiers in bdSYNC mode will produce 5,000 Watts x 1 @ 2-Ohm. Please note, the individual amplifier minimum impedance is 1Ω, but when bridging, the minimum impedance is 2Ω.
Hey rockford team i have a question on the bdcp amps the settings knobs have a small dot is that the mark to go by????
i noticed the knobs are kind diffrent than other amps .
No, the dots are there just for reference, not where you should be setting them. The CROSSOVER is typically set to 80Hz Low-Pass for subwoofer systems and the GAIN should be matched to your source unit or preamplifier output. If you're having problems setting your gains, you can refer to this section "GOOD: SET YOUR GAINS BY EAR" in this article:
How To Properly Set Your Gains:
rftech.custhelp.com/app/answers/detail/a_id/46/
On the T600-4 amp, using the the Punch EQ, if you have the front channel set to High-Pass and rear channel to Low-Pass will both channel pairs raise at the same rate in their respective frequencies as described with just setting it to the the same cross-over across the board? ... I have had this amp since 2008 and has outlasted all of my cars to this date never installed a punch knob on it. I love my Power Series Amplifiers. (T600-4, T2500-1bdcp, T500X1PBR) ... That does not take away from my Prime and Punch Amps ... Power Series just hits a little different. 💪🏾
Hi Juan, great question on a great amplifier! When using the Punch EQ, it can add up to +12dB @ 12kHz (Treble) and up to +18dB @ 45Hz (Bass) depending on where the adjustment is set. When the crossover is set to LP (low-pass) the EQ boosts BASS response. When the crossover is set to HP (high-pass) the EQ boosts TREBLE response. We have a diagram on how it works here: rftech.custhelp.com/app/answers/detail/a_id/918/
Rockford Fosgate I am familiar with the Bi-Amp advisory. However, the referenced diagram does not address the 4 channel amplifiers with a single PEQ knob. Does it imply that both crossovers in the 4 channel amp will simultaneously respond? My guess is that it does ... I’m guessing that the downside of using a 4-channel with a single PEQ know, each channel will respond to the knob’s setting and their is no way to isolate the two unless you get two separate amplifiers. ... I am using the front channels for tweeters (High-Pass) and the rear channel for my mids (All Pass) on my front stage set-up (full active w/ 3Sixty.3 DSP). I’ll test it out in the lab and see when I get time. Thanks for the feedback!
@@PhiMobileSounds Thank you for the clarification. The T600-4 amplifier does feature 2 Punch EQ settings that allow the front & rear settings to be adjusted independently. However, when plugging in the Remote Controlled Punch EQ knob, this overrides REAR channel's built-in Punch EQ setting, because the rear channels are typically bridged for subwoofers and the front channels typically run mids/tweets.
What is the difference on the power amps and the compact power amps besides the size
The main difference is the smaller amplifiers are fan cooled and incorporate the CLEAN gain setup.
Just recently purchased the T1000-AD can the amp be paired with 2 sets of T4652 or T3652 without issue?
Yes, absolutely. The T1000-4ad is a brute of an amplifier and has plenty of output power for 4 sets (2 on front, 2 on rear). Nice choice!
@@rockfordfosgate Thanks
If I buy 13” T2 subwoofer rated at 2000 rms. Should I buy the Rockford power T1000-1bdCP or the T1500-1bdCP amp?
Great question Jameson! How many subwoofers are you planning to use? If just one, then use the T2S1-13 model since it would be a 1-ohm load and perfectly matched for the Power Series mono amplifiers. Since the power handling is rated at 2,000 Watts RMS, we would suggest the T1500-1bdCP. Although it's rated to produce 1,500 Watts x 1 @ 1-Ohm, its dynamic power is actually 1,715 Watts x 1. This is under the rated power handling of the subwoofer and a perfect match!
I have a Sundown Audio Sa series 2 ohm dvc can a Rockford Fosgate T600-2 push that 15 and how should I wire my sub to work with the Amp.
So the subwoofer is rated to handle up to 750 Watts, correct? Since it's a 2-ohm DVC subwoofer, it can be wired to create a 1-ohm load or a 4-ohm load. The T600-2 amplifier is designed to produce 600 Watts x 1 @ 4-Ohm Bridged. Look at the WiringWizard tab on our T600-2 Product Details Page and use Wiring Diagram #2 at: www.rockfordfosgate.com/products/details/t600-2
Rockford Fosgate Thank you it can be heard a block away this one bad mother it isn't very big but man it Packs a Punch the gain is up a notch , who would have thought. Rockford Fan 4 Life.!!!!!!!! it sounds way better than a set of 12's. #No doubt. It's a little Monster.!!!!! 98 Honda Passport is a Beast and competing with a Yukon or a Tahoe. Much love Happy Camper.!!!!
Currently running t2652-s components front and rear t1650 coaxial with p400×4 amplifier. what amplifier would u recommend for best sound quality and loudness to get out of the speakers since they are only being fed 50rms
Hi Eloscar 57, Thanks for using Rockford Fosgate for your ride! Both those are amazing SQ speakers. Right off the top, these look like an awesome match! So, let's breakdown what you have:
• The T2652-S are rated to handle 100 Watts RMS
• The T1650 is rated to handle 75 Watts RMS
• The Punch P400X4 Continuous Power is 50 Watts x 4 @ 4-Ohm and Dynamic Power is 82 Watts x 4 @ 4-Ohm
The Punch P400X4 is a great Class-A/B amplifier designed for SQ and exactly what you want to match with your SQ speakers. The power output matchup between the amplifier and speakers couldn't get any better. As you know, Rockford Fosgate amplifier are typically considered "under-rated", so you can easily expect the Dynamic Power output from the amp. If it's not loud enough, you may need to start looking at adding multiple drivers to increase your SPL output. Otherwise, this must sound amazing.
Would this amp be good with two p3 dvc 4 ohm subs?
It would be to powerful. Get a punch series amp
Hi RF I know this video is old but can I use the T400-2 for tweeters, using the power T2 components and want to go active. I hope I get a reply. Thanks
HI Neelchand, the Power T400-2 is rated to produce 120 Watts x 2 @ 4-Ohm (dynamic power is 145W x 2). The T2652-S is rated to handle up to 100 Watts RMS, so technically this amplifier will overpower the T2 components, so we advise caution or using a slightly lower powered amplifier.
Can any one help.. I Have two T0D412 subs and a T15001-bdcp amp would like to know if it’s a good match a good match
I have 2 p3d4 12a. I want them to hit hard and play kill low notes. Which power amp would I need?
HI Bryce, I answered the same question you posted on another video here:
ruclips.net/video/Il--ghOK6iM/видео.html&lc=z22whtjbolr5vlyrr04t1aokgwd0vrtyeo1jfsuwe0ywbk0h00410
One more question my friend, what happens if I run the amp t-1000.1bd at 0.5 ohm?? I have the same model the you show in this video
The amplifier will produce less output and/or go into protection mode. Running the amplifier below the recommended impedance isn't going to get you more output.
Will the Power T600-4 over power a pair of T1692's? Also will a sub (300 RMS) have deep bass with this class amp? Thank you!
The T600-4 amplifier is rated to produce 100 Watts x 4 @ 4-Ohm or 150 Watts x 4 @ 2-Ohm. Dynamic power output is 139 Watts x 2 @ 4-Ohms or 236 Watts x 2 @ 2-Ohms. The T1692 speakers are rated to handle 100 Watts RMS, so this will be a great matching amplifier. Since the T600-4 is rated to produce 300 Watts @ 4-Ohm Bridged, this will be adequate for 1 or 2 subwoofers. This is a Sound Quality amplifier so the bass will be accurately reproduced assuming the correct enclosure is designed for the subwoofers. However, if you are looking for MONSTER bass (like you only listen with the volume at 11 out of 10), you may want to step up to a dedicated mono amplifier. The T500-1bdCP is a good starting point.
@@rockfordfosgate thank you for this perfect response!
@@JBrain58 You're welcome! We also have live techs during 8am-5pm (Arizona) business hours. You'll see live chat at the bottom of our website at rockfordfosgate.com when they are online, or you can always call at 1-800-669-9899 and just talk with them about other scenarios you're looking at. Thanks for help saving the world from bad car audio, one fanatic at a time! 👍
I have got a power t1000-1bdcp amp to fit, however space is tight.
Will it be OK to mount this amp to the back of my dual 12" p2 subwoofer box? I know its not ideal because of the vibrations
Not ideal, so I would suggest isolating it using rubber grommets. That should help when you're in a pinch.
@@rockfordfosgate I was thinking of mounting the amp with a sheet of rubber between to dampen out the vibrations. Thanks for the reply.
I will have a rethink to see if I can squeeze it on the back of the rear seats where I have my t800-4ad mounted.
1000 watt constant power okay for the loaded p3 enclosure?
(1200 rms) i know most rockford amps go higher then they say (which is awesome)
The P3-2X12 is rated to handle up to 1,200 Watts RMS. So, yes 1,000 watts will work just fine.
I'm running my bdcp1000 at 1 ohm on 2 T1 12s and they beat them to death the t1500 bdcp was a bit much for my car to handle the 1000 puts out 1500+ watts and dynamically i would expect in the 2k range. When I buy a 1000 watt power series RF amplifier I expect more than 1000 watts and according to my birthsheet its over 1400 at 2 ohms and over 1500 at 1 ohm. My 1500bdcp does over 2000 watts at one ohm and big d got 3200 dynamically.
@@justinkelsey9218 yeah I ended up getting the t1000 on the p3s birthsheet was 1525 at 1 ohm....thing beats insaaaaaane. Sounds crazy in my 2019 suburu impreza
@@DjTvna im now running my image dynamics id max 12s on an orion xtr 2500 still got my black cone and silver cone t1 12s tho
I got a prime 750 on 4 4ohm svc 8s they handle only 200 watts they do good on the amp but should I have went with the punch 500 what would be the difference
The differences between these two amplifiers were taken from their spec pages:
PRIME R750-1D
250 Watts x 1 @ 4-Ohm
500 Watts x 1 @ 2-Ohm
750 Watts x 1 @ 1-Ohm
PUNCH P500X1bd
150 Watts x 1 @ 4-Ohm
300 Watts x 1 @ 2-Ohm
500 Watts x 1 @ 1-Ohm
I have a 1500bdcp I'm going to run one sub don't know Wich one yet but should I run the amp at 1ohm or 2 ohm what ohm is better and is there a difference on this amp
Although the Power T1500-1bdCP is rated at 1,500W at 2-ohm and 1-ohm, Dynamic Power is rated at 1,549 Watts x 1 @ 2-Ohms and 1,715 Watts x 1 @ 1-Ohm. The amplifier produces the best possible power output at 1-ohm, so you just want to make sure the subwoofer's RMS Power Rating will handle that amount of output power.
@@rockfordfosgate I see people saying running amp at 1ohm makes the sub have not as good performance and the amp won't last as long I have no problem running at 2 or 1 ohm..only if 1ohm If it doesn't ruin the amp..just trying to figure out what ohm is best overall thanks so much
@@jeffeisenzapf4131 The Power T1500-1bdCP is specifically designed to operate at 1-Ohm or higher. Many "armchair-technicians" love to talk others into lower impedances like 1/2 ohm thinking you get more power from the amplifier, which is not necessarily true. I'm glad the advice you read is error'ing on the safer side. The amplifier will work just fine at 1-ohm.
I need a 4 channel power which one I buy the power or the compact power
Either the T400X4ad or the T400-4, it's your preference.
Hi, I have a question, I have the amp t-1000.1bd and I want to connect 3 subwoofers 4ohms each, so the impedance will be 2.67 ohms. The amp will be working fine???
Yes, the T1000-1bd and T1000-1bdCP are stable down to 1-ohm, so although it will have reduced output, it will work fine at 2.67 ohms.
Thanks for answering very fast in less than 5 minutes . ROCKFORD FOSGATE #1...👍😉
At 2.67 ohms what kind of power will it run watts?
I am thinking to buy a single P3D4 12 @ 4 ohms connected to T500BDCP. 2 ohm load. Is this configration correct? Will my amp t500bdcp shut down after excessive usage for one or two hours or even more?
Hi Saif, the Power T500-1bdCP amplifier is rated to produce 500 Watts x 1 @ 1-ohm, so you will be totally fine running it at 2-ohms.
Thx for the answer RF
I'll buy P3D4 12 + T500-1BDCP and wiring will be @2 ohm
I have a scv 3k that clamped around 1500 with a 1 ohm load. Will this RF 2500 clamp around 2500 with a 1 ohm load?
We run true Dynamic Power tests against Rockford Fosgate amplifiers. Assuming you're referring to the Power T2500-1bdCP? It's Dynamic Power numbers can be found under the SPECIFICATIONS tab on our website: www.rockfordfosgate.com/products/details/t2500-1bdcp/
T2500-1bdCP Dynamic Power
1823 Watts x 1 @ 4-Ohm
2940 Watts x 1 @ 2-Ohm
2980 Watts x 1 @ 1-Ohm
I was talking about clamping in a car. The way you have the sub in a car will change the ohm level. If I use this T2500, it should clamp 2940 watts in the car cause my ohm level moved up to 2 ohms from 1 ohm. and 2 ohms is about the same as 1 ohm on this T2500. If this will happen, this is the best amp technology out there. And i am a believer. And will buy this amp. I would love to see real wattage in the car.
The Constant Power technology inside the T2500-1bdCP is pretty amazing! You can learn more about CP and how it works here: ruclips.net/video/7EP4-4TMWFw/видео.html
Regarding "clamping" ... not 100% sure what you're referring to because the impedance plot of a subwoofer/enclosure is very complex. In addition, the effect on the amplifier is complex as well (see the Constant Power video above.) It's not a cut and dry 1-ohm/2-ohm equation.
The Dynamic Power tests we use at Rockford Fosgate are NOT based on simple resistive loads, because loudspeakers (subwoofers) consist of capacitive, inductive, as well as resistive loads. The Dynamic Power data we publish is considered "real world" to what is capable in the vehicle. I wouldn't read too much into forums that weigh heavily on "clamping" and "box rise". There are simple factors like charging system voltage, proper grounding, and current reserve (energy storage capacitors) that have a much larger effect on amplifier power than those factors.
? I have T1500BD the sub are dual 2ohm 10inch Kicker Comp Q rated 700 watts rms what's the best way to wire them ?
Running 2 10 dual 2ohm Kicker Comp Q series
Hi Mchickencat, do you have the T1500-1bd or T1500-bdCP? Is the "bd" in the model number RED on the amplifier badge?
I am debating between the p600x4 and the t400x4ad to run 4 of my door speakers i’m not sure which one to go with. My front speakers are 80rms and rear is 55rms, i know “power” wise that the Punch should be good but i hear the Power amps just sound better. Anyone have any ideas?
Hi Francisco, the main difference between the Punch and Power in this regard is the slight power differences and the circuit topology. The Punch model use Class-AB (sound quality) and the Power uses Class-AD (class-d). You'll have better sound quality with the Punch model, but the Power amp provides similar power in a compact package. If you have the room, use the Punch model. If you're tight on space, use the Power model. Here's a quick overview of the specs:
• P600X4 ($399.99): 75 Watts x 4 @ 4-Ohm / 150 Watts x 4 @ 2-Ohm / 300 Watts x 2 @ 4-Ohm Bridged
• T400X4ad ($439.99): 100 Watts x 4 @ 4-Ohm / 100 Watts x 4 @ 2-Ohm / 200 Watts x 2 @ 4-Ohm Bridged
Does anyone know how I can tell if my amp is in fact the Constant Power model not the older one? I don't have the manual nor box.
The Constant Power models have a RED colored "bd" in the model number badge atop the amplifier.
@@rockfordfosgate and the tag on the bottom will say bdcp if its still there
I'm planning to buy two JBL CX Series 12" single voice coil 4-Ohm subwoofers for black friday, which amp do you recommend for my 2015 gmc sierra 1500 crew cab, by the way I'm planning on keeping my BOSE speakers for the highs
Hi Juan, the JBL CX Series 12" are rated to handle up to 250 Watts RMS each, so two subwoofers would give you 500W Power Handling and can be wired in parallel to create a 2-ohm load. If you're looking for just a mono subwoofer amplifier, you could use the Prime R500X1D since it's rated to produce 500 Watts x 1 @ 2-Ohms. However, I caution you if you love to hammer your system... that amplifier can produce up to 647 Watts which would over power your system.
If you're looking for a multi-channel amplifier to also run the mids & highs, we'll need to see what the RMS power handling is on the speakers, so without knowing, you could use either the Power T1000-4ad (250W x 2 @ 4-Ohm for the stereo channels and 500W @ 2-Ohm Bridged for the sub) or the T600-4 (100W x 2 @ 4-Ohm for the stereo channels and 300W @ 4-Ohm Bridged for the sub.)
I'm going to to with the Power T1000-4ad thanks
That's a great amplifier! Be careful when setting up the gains for your tweeters and midrange because it's one mighty powerful amplifier. Just want to make sure your system lasts for a very long time. You may want to setup the Gain Overlap at 0dB for those speakers.
I'm kind of confused because you first mentioned the JBL CX1200 12" woofers I'm trying to get handle up to 250 watts RMS each but on the description it says 1,000 peak power each, or am I being understood between RMS and peak power?
I agree it's confusing. If you can't find the certified power ratings (CEA-2016 for amps and CES-2031 for speakers) then always use the RMS Power Ratings. "Peak Power" or "Max Power" ratings are usually just double or quadruple the RMS ratings to represent "this product can handle this power for a few milliseconds".
As mentioned earlier, the Power T1000-4ad will be great using the rear bridged channels for the subs and will generate 500W for both subwoofers (250+250=500). I'm just suggesting to use caution on the front channels because you'll be delivering 100W to the left and right sides, so check the power rating of your tweeters & midrange. To be safe, set the gains on the front channels to 0dB Gain Overlap so you don't over drive them.
I have a (2007 year made) rockford fosgate p500 1bd and I have 2 punch 2007(year made) p3sd410 can I conect them to 1ohm with this amp or this subwoofers??
You mean the P500X1bd? Yes, it's designed to run at a 1-ohm load.
@@rockfordfosgate No. I bought it in 2007 and the owner manual says P500 1BD
@@mikemorales5361 Ah, the Punch P500-1bd. Yes, it's also designed for a 1-ohm load. You can find the owner's manual here: rftech.custhelp.com/app/answers/detail/a_id/865/
@@rockfordfosgate great now i know I can run this amp at 1ohm. But M'I in a safe zone to run the 2 punch p3sd410 that I bought back in 2007 without burn them??
@@rockfordfosgate or would be better to run them at 2 ohms??
Hey there I just bought one of this will it work for 3 12s jl w6s they need 500 rms is this amp weak for my subs or perfect
Hi Kevin, sounds like you may have the 12W6v3-D4 or the 12W6v2-D4 and they are rated to handle 600 Watts RMS. They don't necessarily "need" 500W, but typically a subwoofer like this works great from 30% RMS up to the RMS power rating (150W - 600W). Since you have 3 of the dual 4-Ohm voice coils, they can be wired to create either a 6-Ohm or 2.67-Ohm load and have a total power handling capacity of 1800 Watts (we'll assume you'll wire them to create a 2.67-Ohm load.)
A great amplifier is the Power T1500-1bdCP. It's rated to produce 1500 Watts x 1 at both 1-Ohm & 2-Ohm loads due to its "Constant Power" technology. We don't have power ratings at 2.67-Ohms since it's an odd impedance, but under Dynamic Power conditions (real world) it can produce up to 1549 Watts x 1 @ 2-Ohms. This is PERFECT to power these subwoofers without exceeding their power limitations. Here's a handy link to that amplifier:
Power T1500-1bdCP
www.rockfordfosgate.com/products/details/t1500-1bdcp
Rockford Fosgate thanks I getting a cutcab done rn with 3 w6s v4s with a 4th order box hope that amp gives these sub the power they need
Sounds great Kevin! If you need any assistance setting up the amplifier, feel free to give our tech's a call at 1-800-669-9899. They'll be happy to clarify any questions you may have.
I have a t1500BDCP powering 2 JL W6v2d4 12” at 4 ohms, the amp gets hot, do I need to upgrade my vehicles electrical?
Does the amplifier shut down? If so, how long does it run before it does?
Rockford Fosgate it doesn’t turn off right away, it did stay on for a while of playing loud music.
It took about 20-30 minutes
There's nothing wrong with the amplifier. Our MEHSA technology moves the heat away from the MOSFET more efficiently away to the heatsink like NO OTHER amplifier on the market. The heatsink is doing exactly what it's designed to do, dissipate heat. Look at this video at timecode 01:55 where we describe what MEHSA does for the cooling effect.
Wat kind of sub is the best to run on that amp
There are several Power Series amplifiers discussed in the video, but we suggest matching the RMS power handling of the subwoofer with at least the RMS power of the amplifier, preferably the Dynamic Power. The point is not to exceed the RMS power handling of the subwoofer.
Rockford Fosgate so with this amp I got what subs well be the best to use in Rockford fosgate brands
Rockford Fosgate subs of course ;-)
Hi there, i have 2 punch p3 shallow sub and set of T2 components on the front and set of power coax on rear door what amp should i use? F
What model number P3 Shallow subwoofers do you have?
P3SD2-8, P3SD4-8, P3SD2-10, P3SD4-10, P3SD2-12, or P3SD4-12?
Rockford Fosgate p3sd4 10
O.K. great! The P3SD4-10 is rated to handle 300 Watts RMS, so two subwoofers will give you 600W total power handling capacity. These 4-ohm DVC models can be wired to create a 1-ohm or 4-ohm load.
There are several options, you could use a single amplifier like the P1000X5, or use two amplifiers like the P500X1bd for the subs and the P400X4 for the front components & rear coax.
Rockford Fosgate thank you! I brought p1000 2x and p400x4.
Great! Our only suggestion is be careful with the P1000X2. That is a powerful amplifier and it will most certainly be feeding nearly double the power those 2 subwoofers can handle, especially being "shallow". Good news is ... this future-proofs your setup if you to upgrade to the Power T1 slim subwoofers as they respond more like a traditional subwoofer and have higher power handling capacity.
Can i run it 0.5ohm daily? My box rise up to 1.3 ohm
No Rockford Fosgate amplifier - old or new - is recommended to run below the recommended impedance as stated in the owner's manual. 0.5 Ohm daily is not recommended. This is because "Box Rise" is not a constant, and therefore can cause dangerous low impedance conditions for the amplifier, running it harder and shorten the life expectancy of the electronics.
I wired my sub to rockford t2500bdcp to 0.5 ohm, I checked many frequencies and my lowest box rise was 1.1 ohm . Rockford recommendation is 300 ampere external fuse for t2500bdcp and when I played 33 hertz tune and the box rise was 1.1 ohm my external fuse is blown. Rockford says that on 1 ohm load this amp will give me the same power that on 2 ohms, but if i wire my sub to 1ohm load there is always will be more than 1 ohm because of box rise
What do I set my gains on my T600.2 I bought it used the gain was set at 5, The EQ was set at 125, and the Hertz was set for 60 Hertz . I'm putting it to push a SA 15 2 ohm dvc are those gains setting good. should I leave it alone. please let me know what to set it at for 1 SA 15.
Hi Gz, the Power T600-2 amplifier gains should be set to match the source unit. We have an article on setting gains here: "How to Properly Set Your Gains" rftech.custhelp.com/app/answers/detail/a_id/46 . For the crossover, I would personally set it to 80Hz since a lot of bass comes from the 50-60Hz region (the current crossover setting is set to -24dB at 60Hz so you're losing lots of bass).
so why 80 Hertz? and my eq is set to 124 on the amp and my gain at 5 . what do I set the eq on the amp? and why 80 Hertz if I'm losing alot of bass. my unit is is set at zero and natural sound I got bass blockers on my highs it's a pioneer head unit.
Did you have time to review the tutorial on Setting Gains? It explains how to adjust your gains with and without an equalizer, regardless of the source unit being used. The crossover frequency is just a recommendation, but as mentioned earlier, the current crossover setting is set to -24dB at 60Hz (it doesn't "start" at 60Hz) so you're potentially losing a lot of bass if you like the hard-hitting frequencies that typically reside at 50-60Hz. We also have an article on crossovers if you need more information on how they work here: rftech.custhelp.com/app/answers/detail/a_id/68
I have a t1500, and had 2 type Rs hooked up to it. But the amp is just too much, what are some great subs to go with this amp?
Hi Jose, the Power T1500-1bdCP is a great amplifier and is rated to produce 1500 Watts x 1 @ 1-Ohm but can dynamically produce 1715 Watts x 1 @ 1-Ohm. The following woofer combinations give you at least 1500 Watts of power handling capacity:
(1) 2Ω SVC Woofer to create a 1Ω load:
• T2S1-13 - Power 13" T2 Single 1-Ohm Subwoofer
• T2S1-16 - Power 16" T2 Single 1-Ohm Subwoofer
• T3S1-19 - Power 19" T3 Single 1-Ohm Superwoofer
(2) 2Ω SVC Woofers to create a 1Ω load:
• T2S2-13 - Power 13" T2 Single 2-Ohm Subwoofer
• T2S2-16 - Power 16" T2 Single 2-Ohm Subwoofer
• T3S2-19 - Power 19" T3 Single 2-Ohm Superwoofer
(4) 1Ω SVC Woofers to create a 1Ω load:
• T2S1-13 - Power 13" T2 Single 1-Ohm Subwoofer
• T2S1-16 - Power 16" T2 Single 1-Ohm Subwoofer
• T3S1-19 - Power 19" T3 Single 1-Ohm Superwoofer
(4) 2Ω DVC Woofers to create a 1Ω load:
• P2D2-12 - Punch 12" P2 2-Ohm DVC Subwoofer
• P2D2-15 - Punch 15" P2 2-Ohm DVC Subwoofer
• P3D2-10 - Punch 10" P3 2-Ohm DVC Subwoofer
• P3D2-12 - Punch 12" P3 2-Ohm DVC Subwoofer
• P3D2-15 - Punch 15" P3 2-Ohm DVC Subwoofer
• T1D215 - Power 15" T1 2-Ohm DVC Subwoofer
Just got a t1000db to push my 2 10 inch T1s can't wait for install my pdx1000.1 just shit to bed......
I currently have a t1000bdcp, t1500bdcp and t400/4. I'll never run anything but Fosgate and have been since mid 90s....sorry not sorry
@@tjaprilgage The T1000-1bdCP, T1500-1bdCP, and the T400-4 are very powerful amplifiers designed to produce amazing Sound Quality!
@rockfordfosgate they definitely do that. There's just little different about a RF amp and when you know you know. I guess maybe that dynamic power . I own other amps but they just ain't the same.
@ Awesome! Thanks for sharing your feedback with other Fanatics!
Is one t600-4 enough for 8 pps4 6.5? Or should i get two t600-4 and run 4 on each amp?
One amplifier is good because you can run 2 sets on each channel for more power at 2-Ohms in lieu of getting a 2nd amp and running at 4-ohms.
@@rockfordfosgate My t600-4 has arrived as well as my 8 pps4 6.5 midrange drivers. Will wiring 2 sets individually to each channel create the 2 ohm load? Or do i have to bridge them?
@@victorl147 Wiring two 4Ω midrange in parallel will create a 2Ω amplifier load. YOu can use our Woofer WiringWizard for illustrations on how to wire here: www.rockfordfosgate.com/support/wiring-wizard/