Yamaha YFM700 Grizzly Won’t Start | Yamaha ATV Starting Problems | Partzilla.com
HTML-код
- Опубликовано: 5 сен 2024
- Buy the parts to fix Yamaha ATV starting problems: bit.ly/yamaha-a...
Need some help diagnosing starter problems on your Yamaha ATV? We’re here to help. The starting system on your Yamaha ATV is a chain of circuits and components, and failures anywhere along this chain could cause starting problems on your Yamaha Grizzly.
Check out our exploded Yamaha YFM700 Grizzly starting system diagram to get a look at the parts before we start testing: www.partzilla....
We’ll start and end with some simple explanations, and in the middle we’ll get into the meat of the electrical system on this Yamaha Grizzly. First, the battery will need a test. If it’s dying on you, it’s a simple replacement that you can find at Partzilla.com. Once you get past that, we’ll look at the starter motor, the relays, the brake light relay, and the diode. After we get done looking at these connections, we’ll check out the switches. The kill switch and the starter switch could be the culprit, and we’ll also look at the switches on the gears.
Read how to do this job step by step: www.partzilla....
If your battery is dead, you may have charging problems on your ATV. Find out how to diagnose ATV charging problems: • Yamaha ATV Electrical ...
If you need an ATV or motorcycle battery tester, click here: www.partzilla....
VIDEO HIGHLIGHTS:
Checking the battery - 2:15
Replacing the battery - 3:00
Starter motor test - 4:00
Relay test - 5:30
Brake light relay test - 6:50
Diode test - 8:45
Run switch test - 10:45
Engine start switch test - 11:25
Gear and reverse switch test - 12:25
Find thousands of Yamaha ATV parts here: www.partzilla....
Talk to us:
Twitter: / partzilla
Facebook: / partzilla
Instagram: / partzilla
In the video we’re working with a 2007 Yamaha Grizzly YFM700, but you may have similar steps for your Yamaha ATV. If you’re not sure whether these steps apply to your machine, leave a comment and we’ll get back to you.
RELATED CONTENT:
Yamaha YFZ450R Charging Problems:
• Yamaha ATV Electrical ...
Yamaha YFM700 oil change:
• How to Change the Oil ...
How did you clean this so good? Please do a video on how to clean where electrical components are
I'm here now for my confession. After I let a kid start up my Kodiak for fun, it later refused to start. I checked everything - connections, switches, fuses, battery, grounds, relay, even regulator. NO LUCK. Then I sat on the quad and tried to remember what he might have done while sitting on it. Then I discovered a very small button I NEVER KNEW EXISTED under the starter switch - the engine kill switch. So after replacing the solenoid and almost submitting to a mechanic for help, I found the problem. The kid had hit that button by accident I never knew it. I told my wife I had finally found a loose plastic wire connector, so we'll leave it at that.😁
I like to watch his videos I learn a lot
Excellent video. One comment. When working on the battery or starter relay positive wire. Remove the the negative wire from battery first. Then work on the positive wire. When your set up for a test reconnect the negative battery wire.
Reason for this is the negative side of the battery is connected to ground, all the metal of the machine. You don't want your wrench connecting positive to ground.
Hello thanks for the great video I'm having some issues with my grizzly 700 turning over but not starting do you know where the fuel pump relay or fuse would be? Kindest regards
Excellent as always. I just bought a used 1998 Yamaha Grizzly 600. When I turn key there is just a click and a buzz. I replaced starter relay and same thing. I can jump the relay posts and motor will turn over, but for the life of me I cannot get a connection through the push button. Driving me crazy
Having the same problem did you get it fixed ?
Great Video presentation. I've got a customers bike in the shop and it's a total mess when the original rider was a young kid that destroyed this 2004 Yamaha Bruin 350 4x4 harness. I've never seen so many splices and twisted wires in my life. So far I have determined that the starter relay is shot. I also believe a pigtail should be on these quick disconnects .
How do I go about cleaning the battery area as you did?
Kareem Hinkson would love to see this also!
Informative and helpful video for testing the relays. But what about those 5 pin relays? They are easy to test their function with voltage, but how to test them for resistance?
The 5 pin resistors seem to function opposite the other resistors. When power is applied, then the resistance in that middle pin goes from low to high?
What is the tool you are using when testing the resistance on the diaode? Assuming the red & black clips replace the usual testing nodes and input on the mulit-meter respectively, but what is that other unit you're using called, exactly?
Your are a rockstar and a gentleman!! Thanks
I appreciate that!
As allways a very informative video!. Thanks john👍
So got a 2023 Yamaha grizzly 700 eps se. Have a total rebuild on engine. Turn it on hit start button runs dies it does this about four to five times then runs on its own. Any ideas before I take it back to the shop.
if it starts in park but not in high with brake, tighten rear brake switch spring. i just used needle nose and bet the end more to tighten up the spring.
Thank you for the kind, thoughtful and helpful video.
I have a 2016 Yamaha Kodiak 700 EPS SE that stopped while my wife was running it. The machine is a work vehicle on our ranch. We do not race or use the machine for play.
Prior to it stopping we did not notice any error codes on the display. And now the display will light up but it does not show any data.
i have put a new battery in the machine.
When keyed on the screen will light up but it doesn't display any information. I do not hear the fuel pump run.
The engine will turn over but not start. The lights and winch for example, do run.
I hear clicking noise when first keyed on. I placed my finger on the object it to confirm, it looks like it might be a relay clicking on the right side of the machine. When first keyed on one clicks, the other doesn't make any noise.
To check the fuses, I placed the negative terminal of the multimeter on the negative post of the battery. I keyed the machine on, I then placed the positive terminal on each fuse and checked both sides of the fuse for voltage.
They all read 12.X volts.
Can you suggest further troubleshooting processes?
Since the display lights up but doesn't display any data like miles or hours on the machine could the ECU have failed to cause this?
Thank you and happy trails, Mike
hi, check the lean angle sensor
@@luis420ification thank you. It turned out the fuel pump was causing a short that was blowing the 15 amp fuse located on the starter relay.
Is it the 2 sensors on the stator ?
Quick question, what does the harness connected to the starter relay go to?
When yu jump the starter and Don't turn over does that mean it's no good
Before I order a new ECU for my 2009 Grizzly 550 Hunter, is there a test sequence that I can perform?
Diodes checks out good,so what happens when it’s bad. I got voltage across both wires on solenoid coil.
I replaced the starter and starter solenoid on a 700 Kodiak. It now cranks over but I lost my digital display in the process, still won't fire up, what did i do wrong?
What did you use to clean up so well in around the battery area? Just curious of the product if there is one.
How the heck did you clean the battery/ECU compartment that easily? Looks brand new!
I have a grizzly 700 that has the big bore kit and it’s showing two codes on the screen which is 12 and 22
Hi
thanks for the informative video.
Perhaps you could help me with a problem with a 2009 YFM550,
The bike starts and runs fine, intermittently it stalls at any RPM, it will restart but shows a error code 33, it will then run fine for a period of time, then repeatedly stop. I have replaced the coil and tested new and old with no problems. I know code 33 relates to ignition coil, any help be appreciated.
Cheers
Bill
This is common and almost impossible to figure out. If you tested coil packs and they are good, usually you have a direct short somewhere on the harness. You can try to trace them and sort it out, or get a new harness and run it. Not great options, but not much else to do.
I have a 2007 Yamaha grizzly 700 and it will turn over but it is to week to start I tried to jump it off with the car and same thing happened with are some of the things that would cause it to act that way
I have a 2009 Grizzly 4wd, and after it warms up, I can turn it off and it doesn't want to start. Just cranks over. Any thoughts?
Grate video.
Got I brand new Yamaha. After cold weather getting problems with battery local dealer checked it up and charger it, it starts, after a night the same problem, engine want start.
Does anyone know is it under yamaha warranty ?
What if you replaced the starter and the starter relay but the machine still won’t start while in neutral?
Great thorough video. I have a 2013 Grizzly 700. Looks very similar. Do you know if it’s the same staring circuit.
Thanks John,, I listened to you now my buggy won’t start,, used wire to cross solenoid, burn something up don’t know what, gotta take it to dealership. So my word to everyone is Don’t listen to John tally
Very well explain 👏
I have a 2005 Grizzly..you talked about a scenario which happened to me recently-I rode my bike down my graveled dirt driveway, about an 8th of a mile. It was running great (I live on a bumpy dirt road) when I got back on it wouldn't start. That was a month ago or more. My main problem is...I cannot remove the outer plastic shell..it has "pins) in it with teeny screws? In them so I first used a screwdriver...no luck..then I read that you should push the pin in and it should pop out. No luck. Can you please teach me how to get the shell off ? I know I could fix it by watching your video, but I need to see what I am doing and get my hands in there! Thanks a bunch!
Instead of pushing the pin in,PULL the screw/pin outwards.There is a tool for this or small flathead screwdriver will work,slip it in between pin&housing of pin.This is an old thread so you probly already solved this.
This was great
Hello, I have a Yamaha grizzly 450. Starter relay keeps blowing the fuse 30A, I replaced the starter relay, still the same problem. Any idea
G'day John, I have a kodiak ultramatic 4x4 oncommand, The starter is spinning but is not engaging. Is the engage mechanism in the motor as i removed the starter and usually you can see a spring on a twist spline which throughs out and engages the cog. I am guessing this is part of the internals. I cant find anything online about this particular problem. It has been working fine up till a few days ago. A now it like a light grinding sound. The cog the starter spins on looks good. Any advice would be great. Cheers Daz
When checking the starter relay/solenoid, what is an acceptable resistance reading? For example I have a 2008 Grizzly 450 and when I do your test it reads 3.4 ohms. Is the starter relay good? The service manual I have just says check for continuity, no reading for resistance. Love your videos. Very helpful
Had the same question. I found that it should be under 5ohms.
Great video! Thanks for sharing your wisdom.
having similar issue but i turn key on only eps light comes on dash the rest of dash wont light until i hit start buttuon and it wont stay running unless i hold down start button down
John, what about the neutral safety switch? How can you test that?
What does it mean when my starter relay consistently clicks. Seems like everything is ok?
The ignition fuse keeps burning out.
I have a 2016 Yamaha kodiak 700, the starter relay buzzes when I hit the start button, I checked the battery and charged it and replaced the starter relay assembly. The bike still buzzes when trying to start, any ideas??
Did you ever figure out you’re Problem? I have the same quad, same problem.
Y'all found the problem yet I have same issue
@@gustavohernandez8642 I replaced the starter relay assembly got a new battery and was still doing the same thing. When looking at the bike from the front it was one of the small relay fuse box on the left, the wires were so corroded with mud that they weren't even making contact with the fuse. I rigged up some new connectors to the wires plugged it into the relay box and never had that issue again. I also had this issue with the fan but I never fixed that issue.
with all these plug in connections would it be a good idea to put special purpose grease to help keep moisture out and preserving the contacts?
No need, they have a rubber seal on them.
Thanks for sharing! Im not sure on what the problem is on my 2017 Grizz SE as it wont start as soon as its a little cold (eg: -5 in garage). New battery ,new spark plug, turn over good but no start. Have you ever seen this issue? Any info would help. Thanks
Mine does the same. Fine all summer but as soon as it starts getting cold, turns over but won’t start.
Hi, Need some help with my 2003 660 Grizzly, the display was not coming on when turning on the main switch, moved the wires a bit , display came on, later on I heard the machine trying to start itself with kill switch and main switch off, turned on the main switch and it started, shut of main switch machine continued to try and start, kill switch would not shut if off, had to disconnect the battery
Hi you have some great videos but I have a question I got a grizzly 700 at auction and it starts for a few seconds and stops and the meter only shows mileage and hrs only when it is running thanks
I have the same issue I think. My display don't work unless I'm pushing the starter button. Will fire while pushing but when I release the button it dies
I got a 660 grizzly I have checked all of the wires but it's not turning over
Hello, I have fault code 14 and cannot to start. I checked vacuum pipe - its good shape. I replace a new air pressure sensor - it doesn't resolve a problem. I can not delete fault 14 (I do it as described in repair manual) all other faults always disappear but fault 14 not. Any suggestions is highly appreciated. Thank you.
Hello. Can oyu please tell how to delete fault code on grizzly 700 2007 I
can not wire for grounding with EPS controller. Maybe it is different
for 2007 and 2008.
Thanks
Amigo mi bloqueo de diferencial de grizzly 660 2005 no fumciona de la nada que sera
Do you even check the video replies??? Just wondering. If I could find a schematic for this machine it would make things easier
I am not getting power to the display.... yet there is power to the switch?
What am I missing?
I have a 98 grizzly 600 I can pull start but it will only spin over and not fire with the starter
fantastic video
How do I make The coil my 660 grizzly fire
John, my brake light doesn't work with the rear lever (left) and pedal. Also, does not start in gear. I have checked continuity on the left lever switch, it appears to function. Fuse is good. If the brake relay is bad, would it cause the brake light not to work and the bike not to start in gear. Mine is a 2009 700 Grizzly, the location of the brake relay is a little different from you video. Could you help me with finding the correct relay? Thank you!!!
Also, don't think I am getting power on the brown wire to the left brake lever switch.
Thanks again.
Having same problem with exact same 2009 Grizzly 700,would only start in park no other gear and now having trouble having it idle/stay running once started.Only way to have it not stall out now after having to battery pack boost it is to hold start button in and that's NOT GOOD I feel to do.Maybe for your brake/gear starting issue you might beable to tighten up on spring at brake end.I'm looking for an answer for WHY would I have to hold in GREEN starter switch while it's started to beable to keep it running without it bogging out and stalling.It will start EVERTIME its boosted but stall out without starter button held,have new battery as well,maybe bad fuel?Will be investigating this week.
@@jimbo8617 when mine was running rough it was a fouled plug brought on by by bad gas. New plug fixed it. My not starting in gear was a bad wire from brake lever to the light.
Awesome video
Why does starter turn backward Yamaha grizzly 600cc
How do you tell if the relay is bad? I put a meter to mine with it still attached and tried cranking the bike. It only read about 7.5 volts. But the batter was reading 12. Does that mean the relay is bad?
Relay is just an electric controlled on off switch. The relay will usually have 4 pins, two activate the switch and two are the open or closed circuit.You put 12 volts into the relay, and it should click and either open or close the circuit.
I have a 2008 700 grizzly that will not start. I checked the spark plug, replaced the battery, cleaned the air filter. Cranks over fine, but doesn't attempt to fire. Any suggestions what to do next?
That's just what he show in that video.
great videos man. I have an 07 that I bought used and the (L) indicator will go out when I decelerate but then come back on when I get on the gas. any idea?
Are you in low gear?
yes sir. he did the reverse wire bypass so the R doesn't light up and he said that he had this issue but it didn't seem to affect performance while in Low
Como puedo hacer para traducir en español ablado
Mine is a 2019 Yamaha Grizzly 700 special edition I have just under a hundred and fifty miles on it now it's been back and forth to the dealer for the same issue I will start it up fine ride twenty miles or so shut it off and it will not start back up until the engine is completely cool again the dealer keeps messing with the idle adjustment screw thinking that is the problem it runs for a little while good after getting it back and saying that she comes up again I am lost
And the same problem comes up again
2015 grizzly 700eps turns over but not getting fuel any ideas?
Fuses, fuel pump, throttle body. You'll have to run through the fuel system to see what's failing.
my starter relay buzzes on my 1998 ymf350fwb yamaha big bear when trying to start and wont start
You have a lack of power or the relay is bad. Jump to test.
No wonder the old Grizzlies were so tippy feeling......they have the gas tank and the battery up too high on the machine.
Have grizzly turns over will not start
Резиновый коврик ставиться под аккумулятор, а не на него. :)
Hello. Can oyu please tell how to delete fault code on grizzly 700 2007 I
can not wire for grounding with EPS controller. Maybe it is different
for 2007 and 2008.