Thanks man. Just waiting for delivery of a cross version for my kids. Learning as much as I can so that I'm prepared. I'll try to pay it forward if I come up with any additional tips. :)
Hey man, I just had to tell you that have a good take on this common problem and I enjoyed the video. I wanted to share one thing that also causes the same problems: At around 10.55 or so you can see the float actuator (light metal yoke that swivels on a slide pin) that moves a needle valve. That needle valve is the second most common place for dirt to accumulate. If you remove the slide pin, float retainer and needle valve and clean with spray carb cleaner it will solve a lot of issues that aren't covered by your procedure. AND, if you do the procedure that you outline in this video and remove the throttle slide from the top you can clean the jet you removed IN PLACE as well as clean the slide and entire assembly with very little chance of cross threading anything (brass jets into aluminum) so its worth looking into next time you do this. WHICH, you will twice a year cause these things get more dirt in the fuel than a weed wacker in the dessert. Great video, have fun!
took me straight to the problem! thanks. I also looked closely inside my fuel tank and saw crap in there. so I drained the old fuel while I cleaned the brass shaft and it started again.
if not starting, check the ignition the fuel and the intake, check this major things if not starting, the spark plug, the carburetor, ignition coil, fuel filter, wirings, and also check the fuel tank..
hi it worked for me so thanks alot and btw i started to clean of the carb that made it closer to start then i cleaned it more then even closer to start but when i did this it started first time pull starting it so thanks alot
Mine hasn't started in around 5 years broke the pull start, tried every year or so and after almost getting a heart attack from the pulling I almost gave up. I even tried to weld a nut to the starter so I could use my drill haha can't weld aluminium. Today cleaned the jet and bang she ran.
Try this spray carb cleaner or power tune in your gas tank get it to run then just let it idle lots of smoke will come out of your exhaust its normal rev the engine every now and then until smoke stops or spray power tune only in the breather on the carb it will clean debris and dirt out of carb while ... Well fixin it (To an extent)
the flout doesn't let fuel in it sits on a little arm in your case and when there's no fuel it doesn't flout and as it fills up it rises and closes the needle.
Remove old gas even the gas line. spray carb cleaner often. let cleaner set overnight. mix new oil gas. check spark plug. if it still wont go try starter fluid but not much.
ima try and clean the carb again i took mine all out left it in gas to loosen some oil or what not but when i put it back together it seems that there migt be a problem could be dirt it only starts with choke on and when i open the choke meaning to let more air it bogs well, thanx for the vid
It might be wrong i think u may have your inline filter the wrong way around did u fit it with arrow pointing down towards the engine they normally have a arrow showing which way the fuel needs to flow.
If the issue is not the fuel line and you believe it is the carb, try buying carb cleaner for cars and use it on the bike also the bubble on the carb may be cracked or popped, hope this helped
you have to switch off the air filter and you turn on the gas tank button and it will be work, you wait 30 seconds not more and you switch on the air filter... Try, you don't risk anything...
I'm rebuilding one right now for my nephew. I'm assuming starting it with the real wheel in the air might help cause the clutch locks and wants to turn the rear wheel not allowing it to rev.
Either bad fuel and needs tune or Remove your carb inspect fuel clean carb with ultra sonic or use carb clean and an air line , replace hose and petcock check tune if the carb has a high needle
on top of the carbrator the throtle line is black it screws into the carb take it out . then hold throtle in and it should bring the black peace up and then keep holding the throttle in and screw it back into the carb
Well, it looks like it didn't work that well, possibly a spark plug issue or a piston rings issue? My best advice would be to buy a brand new 15 carburetor so it'll be clean and better, a new spark plug and some new piston rings, or why not to directly buy a big bore kit.
i had my mini dirt bike it running for ages and i haven't used it in a while and i just tried to start it up, nothing. didn't even sound like it wanted to start, so i poured fuel into the spark plug hole and it started straight away, but then cut out, now it wont start at all? I think its because no fuel is getting to engine but don't see why as i have a brand new carb and air filter and yes i have fuel mixed correctly
I'm a real beginner here with pocket bikes but I've had one for like 2 years and I tried to start it yesterday and I did everything and pulled the rope and no noise what so ever
+zesthrax Gaming i had my mini dirt bike it running for ages and i haven't used it in a while and i just tried to start it up, nothing. didn't even sound like it wanted to start, so i poured fuel into the spark plug hole and it started straight away, but then cut out, now it wont start at all? I think its because no fuel is getting to engine but don't see why as i have a brand new carb and air filter and yes i have fuel mixed correctly
Did you watch the video? I talked about both of these things. Your gas line is leaking and so was mine (in video at 3:05). You don't want it to be doing that. Do what I did and replace the whole gas line, making sure you keep the fuel filter bulb. Then see if it starts if not clean the carb. Watch the video though.
These aren't really that "shitty". Someone who doesn't know about small two stroke engines would discount the value of the bike with a comment like that. He has replaced everything but the carb. Old and/or dirty gas sitting in carb gums up all the little passage ways in the carb. Also, I have found most of my replacement parts at local Home and Garden store in weedwacker isle. Including the correct 3/8 fuel line AND FUEL FILTER. I found my bike in the trash and it wouldn't start. I first checked for spark. Had spark, so I swapped carb for new one on of eBay. For the time it would have taken me to soak and clean the old carb in spirits, It was simpler for me to just buy new carb for 8 bucks. Also these carbs, regardless of cleared jet (pinhole) there are other internals that can be clogged. New carbs will run straight out of the box. They just need mnor adjustment. Always run fuel filter and run bike dry by shutting off fuel switch while bike its running before putting away.
i have the same bike i won it from the ex too. i just put a new spark plug it started then after that it wouldn't start. do you think i have to clean the carb?
My pocket bike does not starts, I know it needs a mixture of oil and gas, but I can't find what type of model it is, so any idea what the average mixture is? And if that's not the problem any other ideas?
My mini dirt bike hasnt run for a while and the other day it started, the problem is that it went straight to full rev's when i hadn't twisted the throttle at all, as i wasnt expecting it the bike fliped backwards and the throttle snapped as well as part of the fairing. I am scared to start it again because of this. I've been told that my throttle slider is in the wrong way, but is there any other things that are causing this? Please help
Try clean out the carburettor but if it's an older bike don't replace the carburettor because all the other carburettors you buy are aftermarket you'll find their alot better than the aftermarket but also replace the gasket that links through the engine
+Aqueel Ali i had my mini dirt bike it running for ages and i haven't used it in a while and i just tried to start it up, nothing. didn't even sound like it wanted to start, so i poured fuel into the spark plug hole and it started straight away, but then cut out, now it wont start at all? I think its because no fuel is getting to engine but don't see why as i have a brand new carb and air filter and yes i have fuel mixed correctly
Well the worst problem for mine was I replaced the engine then my uncle who knows a hell load of info about 2 stroke small engines and 4 strokes said the carburettor gaskets might be gone causing a vacuum leak I've been going through carburettor by buying a new one fitting it and still not starting found out all I had to do is change the gaskets. The gasket you need to change are the carburettor gasket that attaches the carb onto the plastic black manifold thing and the gasket that's attaches the the plastic inlet manifold thing onto the engine where the reads are. www.amazon.co.uk › ... › Engine Gaskets try the link it's best to get all gaskets but just pit on the carburettor and reeds gasket
on mine. the little tube connected to that part is leaking gas. is it suppose to do that? also somtimes my bike starts up then when i hit the throttle it shuts off
fuel line is too big which is why it bogs out. getting too much fuel will do that. ive got a pocket quad with a 49cc also. check your fuel key, mine was clogged.
My mini dirt bike hasn't run for about 2 years and the other day i tried to start it, it started but cut out very shortly, i tried it again and it started then cut out . Today it isn't starting, i cant even hear the exhaust wanting to start. I've looked at loads of different videos and they're not really helping. Does anyone know what to do? I dont know much about mini bikes so i dont want to take it apart too much as i might muck it up. Please help
adjust your air, and idle screw, and get a performance carb, i had a million problems with the stock ones, and now when i run the performance carbs all of my problems are gone, and next time, just remove the entire engine. way more easy, and on these bikes you dont even need experience, dont worry if you fuck something up, there are a lot of tutorials on how to (dis)assemble your bike. so you'll know what part is missing if you lost something.
Hey man you need to fully remove the jet on the inside of the carb. There should be a bolt with a jet poking out on the bottom of the carb, take that off the us a flat head screwdriver to take off the second one. Once it's out just lightly tap the two parts apart with a hammer they should just come apart. PS. The gasket in the carb may be fucked so you might want to replace it while you have it apart
All these years gone by and its still a common problem.
thanks for the advice i will try it tonight
This is was so helpful. I bought one that doesn’t start for 20 bucks and sold it running for 250.
Thanks man. Just waiting for delivery of a cross version for my kids. Learning as much as I can so that I'm prepared. I'll try to pay it forward if I come up with any additional tips. :)
Hey man, I just had to tell you that have a good take on this common problem and I enjoyed the video. I wanted to share one thing that also causes the same problems: At around 10.55 or so you can see the float actuator (light metal yoke that swivels on a slide pin) that moves a needle valve. That needle valve is the second most common place for dirt to accumulate. If you remove the slide pin, float retainer and needle valve and clean with spray carb cleaner it will solve a lot of issues that aren't covered by your procedure. AND, if you do the procedure that you outline in this video and remove the throttle slide from the top you can clean the jet you removed IN PLACE as well as clean the slide and entire assembly with very little chance of cross threading anything (brass jets into aluminum) so its worth looking into next time you do this. WHICH, you will twice a year cause these things get more dirt in the fuel than a weed wacker in the dessert. Great video, have fun!
took me straight to the problem! thanks. I also looked closely inside my fuel tank and saw crap in there. so I drained the old fuel while I cleaned the brass shaft and it started again.
It works!!! Thank you. My younger brother is really happy.
Very helpful I got my bike start straight away after your tips thanks
if not starting, check the ignition the fuel and the intake, check this major things if not starting, the spark plug, the carburetor, ignition coil, fuel filter, wirings, and also check the fuel tank..
It’s definitely a spark plug problem because I had the same exact problems on my pocket bike by a new spark plug
just fixed one that we found our neighbour threw it out cause it wasn't starting. Very dope video, Thanks
Thank you so so much I just bought a project pocket bike and I’m going to try this tomorrow
Thank you so much it really helped I look at other videos but nothing that helped and the problem I had you taught me how to fix thank you
hi it worked for me so thanks alot and btw i started to clean of the carb that made it closer to start then i cleaned it more then even closer to start but when i did this it started first time pull starting it so thanks alot
Rider his piston rings are worn out and so are yours.
thaaank youu. I haven't tried the solution yet, but you explained a lot
Mine hasn't started in around 5 years broke the pull start, tried every year or so and after almost getting a heart attack from the pulling I almost gave up. I even tried to weld a nut to the starter so I could use my drill haha can't weld aluminium. Today cleaned the jet and bang she ran.
Thank you soo much really helped my bike and my bike runs perfect now I liked the video and I subed😊
you are a lifesaver sir!thank you!take my upvote and subscribition
CBVoficial you're welcome. thanks for the upvote and subscription
Hey man. The term is a "shut off valve" 😊 and yes, wearing gloves is a good idea. I have a personal issue with gasoline when it touches my skin. 😁
Nice video. The stock fuel lines get hard and brittle as result from the Ethenol in out fuel.
Thank you very much. This was very helpful
Try this spray carb cleaner or power tune in your gas tank get it to run then just let it idle lots of smoke will come out of your exhaust its normal rev the engine every now and then until smoke stops or spray power tune only in the breather on the carb it will clean debris and dirt out of carb while ... Well fixin it
(To an extent)
just found this vid and your engine looks exactly like I have in the 2 pit bikes I have just got, gone grab my spanners now
When ur tuggin on the pull cord don't keep ur hand on the throttle only let bits in at a time cos thats just floodin it
K.LAWLESS how do you unflood it?
@@4x5300 5 year old comment dude.
@@richard6802 5 Year old comment but still a valid question.
You literally just let it sit for about 20 mins or more and itll unflood by itself
@@bursterbros4210 Why am i stupid for not knowing something buster bros?
where in Toronto u located need mine fixed lol
the flout doesn't let fuel in it sits on a little arm in your case and when there's no fuel it doesn't flout and as it fills up it rises and closes the needle.
Remove old gas even the gas line. spray carb cleaner often. let cleaner set overnight.
mix new oil gas.
check spark plug. if it still wont go try starter fluid but not much.
ima try and clean the carb again
i took mine all out left it in gas to loosen some oil or what not but when i put it back together it seems that there migt be a problem
could be dirt
it only starts with choke on and when i open the choke meaning to let more air it bogs
well, thanx for the vid
Thanks so much my jet was clogged and now it's running fine
It might be wrong i think u may have your inline filter the wrong way around did u fit it with arrow pointing down towards the engine they normally have a arrow showing which way the fuel needs to flow.
If the issue is not the fuel line and you believe it is the carb, try buying carb cleaner for cars and use it on the bike also the bubble on the carb may be cracked or popped, hope this helped
you have to switch off the air filter and you turn on the gas tank button and it will be work, you wait 30 seconds not more and you switch on the air filter... Try, you don't risk anything...
I'm rebuilding one right now for my nephew. I'm assuming starting it with the real wheel in the air might help cause the clutch locks and wants to turn the rear wheel not allowing it to rev.
deeds millar yes, thats how the clutch works. Shouldn't stop you from lightly revving tho. Good luck
YOU HELPT ME IT WORKS GREAT THANKS!!!!
Either bad fuel and needs tune or Remove your carb inspect fuel clean carb with ultra sonic or use carb clean and an air line , replace hose and petcock check tune if the carb has a high needle
on top of the carbrator the throtle line is black it screws into the carb take it out . then hold throtle in and it should bring the black peace up and then keep holding the throttle in and screw it back into the carb
"It was a good shit...uh change" 😂😂
Well, it looks like it didn't work that well, possibly a spark plug issue or a piston rings issue? My best advice would be to buy a brand new 15 carburetor so it'll be clean and better, a new spark plug and some new piston rings, or why not to directly buy a big bore kit.
i had my mini dirt bike it running for ages and i haven't used it in a while and i just tried to start it up, nothing. didn't even sound like it wanted to start, so i poured fuel into the spark plug hole and it started straight away, but then cut out, now it wont start at all? I think its because no fuel is getting to engine but don't see why as i have a brand new carb and air filter and yes i have fuel mixed correctly
I am 11 and mine was the carb it was filled with oil now it runs like a dream
Now your 20 yrs old.
Thanks mate it worked
Hey I've been trying to start mines up but nuttin I have a 49cc I've replaced the fuel lines an pouring in trufuel but nuttin! How can you help?
I'm a real beginner here with pocket bikes but I've had one for like 2 years and I tried to start it yesterday and I did everything and pulled the rope and no noise what so ever
I noticed you removed the front fairing where there should be a key, how did you eliminate the key?
that was so cool because i have the same bike as you but its biger than that on
ps thats a good job
What is the model of this pocket bike? I got this exact same one 6 years ago as a gift
it does really work thank you
How did you get such a nice noise out of your bike? Is it a 49cc engine? What exhaust?
it's 47cc and everything is stock. Not sure why it sounds different than yours
Its a 2 can pipe thats why
What is the mixture of gas to oil for it(ratio)
25:1
hi bud, what covers the part of the carb where your choke is, is it just n air filter or is there some sort of cover ?
I have a 100cc mini pocket rocket don't know the maker, but i broke my carburetor and i put a smaller carburetor on it, will it affect it in anyway?
Yes it won't be as powerful
My mini dirt bike wont start? i dont know why its not starting the idle screw is fine and so is the spark plug?
Pull the start a few times then turn the gas flow off and pull again and that should work!its a common problem hope this helps
+zesthrax Gaming i had my mini dirt bike it running for ages and i haven't used it in a while and i just tried to start it up, nothing. didn't even sound like it wanted to start, so i poured fuel into the spark plug hole and it started straight away, but then cut out, now it wont start at all? I think its because no fuel is getting to engine but don't see why as i have a brand new carb and air filter and yes i have fuel mixed correctly
i cleaned my carb and i changed the spark still not starting
Have you ended up fixing it ?
Thank you so so much bro 😊
I need help to connect the yellow small holes that is on the carburetor on the bottom not the hose that's connected to the fuel filter the yellow one
Did you watch the video? I talked about both of these things. Your gas line is leaking and so was mine (in video at 3:05). You don't want it to be doing that. Do what I did and replace the whole gas line, making sure you keep the fuel filter bulb. Then see if it starts if not clean the carb. Watch the video though.
Lol thanks all try it I have the same year one 2009 and same one hope it works
My pocketbike pull chord is way shorter than yours, do u think that could be the problem?
These aren't really that "shitty". Someone who doesn't know about small two stroke engines would discount the value of the bike with a comment like that. He has replaced everything but the carb. Old and/or dirty gas sitting in carb gums up all the little passage ways in the carb. Also, I have found most of my replacement parts at local Home and Garden store in weedwacker isle. Including the correct 3/8 fuel line AND FUEL FILTER. I found my bike in the trash and it wouldn't start. I first checked for spark. Had spark, so I swapped carb for new one on of eBay. For the time it would have taken me to soak and clean the old carb in spirits, It was simpler for me to just buy new carb for 8 bucks. Also these carbs, regardless of cleared jet (pinhole) there are other internals that can be clogged. New carbs will run straight out of the box. They just need mnor adjustment. Always run fuel filter and run bike dry by shutting off fuel switch while bike its running before putting away.
i have the same bike i won it from the ex too. i just put a new spark plug it started then after that it wouldn't start. do you think i have to clean the carb?
Andy try a new coil
i call bs
Andy it’s the magneto that sits on spark plug try replacing it
Tune the idle bolt mine was set up wrong and bogged down on high revs
i got one with 100cc any idea if i need to mix the gas and how?
Hey quick question how do u empty the tank? If it flooded and i want to clean it out. Afraid to put upside down with a full tank. Tia
Kensy McGowan take the line off the carb and open the tank cap
That is how
i won one at the x as well i have not used it at all and now that im older i wanna start it up but it wont :(
Hey I have a 125cc dirt bike and I don't know what rings are or if it's something else plz tell me. It smokes a lot and drips oil from the muffler
you might need to replace the motor I have a 125cc pit bike but mine is racing
your piston rings are shot. you need a top end rebuild of a neat place in the garbage can.
THANKS MEN THANKS but how do i turn the minibike off ?
nick noah turn on the thing next to the gas flower that goes up and down
I though it wasnt going to start and I envisioned the bike being thrown in the bin hahaha
What do u if the back wheel is moving plz help I've never had a pocket/mini bike
What's the fuel/oil ratio u use?
hey my pocket bike starts but keeps going with the fly wheel do u think that i need to replace it
did the trick! Thanks!
i dont think you needed to do all that, you should of tried adjusting the idle screw and it might of worked then
I been doimg that all day it starts and thn dies any ideas?
My pocket bike does not starts, I know it needs a mixture of oil and gas, but I can't find what type of model it is, so any idea what the average mixture is? And if that's not the problem any other ideas?
Probably try 25 parts fuel to 1 part oil but I'm not sure
Is there a way you can start it without the key switch ?
My pocket bike won't start ... I put in a new spark plug and clean the carburetor once alrighty. Any suggestions?
My mini dirt bike hasnt run for a while and the other day it started, the problem is that it went straight to full rev's when i hadn't twisted the throttle at all, as i wasnt expecting it the bike fliped backwards and the throttle snapped as well as part of the fairing. I am scared to start it again because of this. I've been told that my throttle slider is in the wrong way, but is there any other things that are causing this? Please help
Try clean out the carburettor but if it's an older bike don't replace the carburettor because all the other carburettors you buy are aftermarket you'll find their alot better than the aftermarket but also replace the gasket that links through the engine
+Aqueel Ali i had my mini dirt bike it running for ages and i haven't used it in a while and i just tried to start it up, nothing. didn't even sound like it wanted to start, so i poured fuel into the spark plug hole and it started straight away, but then cut out, now it wont start at all? I think its because no fuel is getting to engine but don't see why as i have a brand new carb and air filter and yes i have fuel mixed correctly
Well the worst problem for mine was I replaced the engine then my uncle who knows a hell load of info about 2 stroke small engines and 4 strokes said the carburettor gaskets might be gone causing a vacuum leak I've been going through carburettor by buying a new one fitting it and still not starting found out all I had to do is change the gaskets.
The gasket you need to change are the carburettor gasket that attaches the carb onto the plastic black manifold thing and the gasket that's attaches the the plastic inlet manifold thing onto the engine where the reads are.
www.amazon.co.uk › ... › Engine Gaskets try the link it's best to get all gaskets but just pit on the carburettor and reeds gasket
Aqueel Ali Thanks
I LOVE YOUR VIDS
Most of the time it's pumping too much or too little petrol into the engine try adjusting it
My carb is leaking loads out the over flow pipe on the carb
on mine. the little tube connected to that part is leaking gas. is it suppose to do that? also somtimes my bike starts up then when i hit the throttle it shuts off
hey what is the model name of this bike i have the same one but dont know the brand or anything
I'm not sure how the spring an parts go together on a 50cc coolster pullcord dirtbike
fuel line is too big which is why it bogs out. getting too much fuel will do that. ive got a pocket quad with a 49cc also. check your fuel key, mine was clogged.
My mini dirt bike hasn't run for about 2 years and the other day i tried to start it, it started but cut out very shortly, i tried it again and it started then cut out . Today it isn't starting, i cant even hear the exhaust wanting to start. I've looked at loads of different videos and they're not really helping. Does anyone know what to do? I dont know much about mini bikes so i dont want to take it apart too much as i might muck it up. Please help
How did you take out the jet
thanks man you are awesome!
No problem! Thanks for watching!
Hey guys as i was taking the golden jet thing from the carb i snapped it and half of it it stuck in side and half is out pls help😣
Hi i same bike that you show in demo having same problem....I try every thing with help of machnic but didn't work
Curent problem
adjust your air, and idle screw, and get a performance carb, i had a million problems with the stock ones, and now when i run the performance carbs all of my problems are gone, and next time, just remove the entire engine. way more easy, and on these bikes you dont even need experience, dont worry if you fuck something up, there are a lot of tutorials on how to (dis)assemble your bike. so you'll know what part is missing if you lost something.
3 slow and easy pulls ..... then pull hard. Repeat till it starts. Don’t give it throttle.
K1980 Pray for the world that’s what I do
idle or the carburator (desassembly)
Whats the solution for Problem one?!
hey bro can you help me out?.....I took off all 3 screws but its really hard to take of the carbriator
Hey man you need to fully remove the jet on the inside of the carb. There should be a bolt with a jet poking out on the bottom of the carb, take that off the us a flat head screwdriver to take off the second one. Once it's out just lightly tap the two parts apart with a hammer they should just come apart.
PS. The gasket in the carb may be fucked so you might want to replace it while you have it apart
ey man i noticed that i got the some bike. do you now a way to make it go faster?
Get a smaller sprocket for the bike
cylinder kit and bigger carb
Ok so my pocket bike turns on but won't go I think the throttle might be messed up any suggestions
nice prize.....feel free to have a look at my pocket bike race mods
skullcam nice
What is that bottle called
I need help finding one
Would it work with a mini dirt bike
Aman Sethi yes it would same engine
Yh
Where can I get that exhaust pipe you have?
It's just the stock exhaust, don't know where you could get one aftermarket. Sorry
Destroyer215 www.minibikestunter.nl/detail.aspx?id=1564
Why part shows that you start it and when you pull the throttle back it cuts off