Lots of knives will be ruined trying this. Takes a steady hand, and a very specific steady angle. If you're new to sharpening, this may not be the technique to try with a knife you care about
A flap disc is too coarse for this job they are mostly 60-100 grit you should be closer to 240 grit and 10,000 rpm is too fast you will create heat in the edge
As soon as your blade heats up and changes color at all, your hardening and tempting are gonna. It will never hold an edge again. It might as well be scrap steel. Angle grinders are WAY TOO FAST.
I thought the same thing. When I seen the sanding pad on the hand grinder. Mower blades are good & that's all I would do!! I paid a lot for my knifes!!!!
Shouldn't he have gone to the other side of the grinder for opposite side of the knife? How can he grind when the wheel is arriving on the knife edge. It should always be moving away.
Thx for the idea! Grinding machine must be set to the lowest speed. Additionally, it is difficult to hold the knife at the correct angle - on both sides! The angle specified by manufacturers in Europe for chef's knives is almost always 15. If you sharpen the knife to an angle of 12, you will have to grind for quite a while because you have to grind away steel. Your idea is therefore only good for experienced people. There are simpler methods. Skully from Stuttgart, Germany
@@creationholic101 The video doesn't show how to sharpen the opposite side of the blade. When you turn it over the edge of the blade will dig into the flapper wheel. Just use sharpening stones and do it right.
If I am not mistaken, I believe the video shows the knife blade being sharpened from both sides. Also, I think there may be a little more time involved than just "3-minutes" to do this exercise---- but a training video (or even training someone in person) always takes more time than doing the actual job. Other than that, I think it's a great idea for sharpening a blade---Thanks .
Se, após 15 dias, você "afiou" a faca, usando a ferramenta e produtos do vídeo, mas a faca ficou novamente cega, fale comigo. Sou fabricante e afiador de lâmias e te digo o que deu errado.....hahaha
This needs a half a thumbs up. Grinder is wrong!! Eats to much of your blades and or knife. What you really want is a belt sander. Lawn mower blades 3 swipes each side. Knife, maybe 2 swipes. So 5-10 seconds
Kept a kitchen knife at work for cardboard and whatever, sharpened it with a belt sander, it lasted 20 years, knives can handle much harsher conditions than what is generally shown in sharpening ,maybe not this, it would round the edge and make uneven cuts in the steel.
I sharpen my knives at home with a typical dual grit sharpening stone. The technique takes a bit of practice but is not difficult. Plenty of videos on the net
Youd have better luck just using a belt sander with high grit paper. Grinding the blde literally does just that...grind away. Just buy a whet stone and sharpen your knifes the professional way.
The first sanding disc is 100 grit. What is the second disc with the polishing compound? Also what is the purpose for cleaning with toothpaste at the end? I typically use a 17° angle for my knives which is typical of Japanese knives. I also use sanding belts and buffing wheels and precision guides even though I have many fine stones (...but, no time to work with them unless I am in the woods without electricity and a machine shop)!
If you don't pay attention with a sharpening stone, you know what you get? A messed up edge. If you don't pay attention with a grinder and a blade... who wants to answer?
DO NOT DO THIS. This method will overheat the metal on a microscopic scale which will make the steel soft and it will not hold the sharp edge for very long and this permanently ruins the knife.
This is dangerous to do to a grinder. That knife cud bite the disc and send it flying towards you.. not a smart way. Doing this could lead to serious injuries
its effective but its dangerous. i would suggest desktop mini grinder wheels they are far safer then this. but it works and effective. just very unsafe.
👎 Начало видео, где давит на томат и конец, где режет с поступательным движением, это дешовый трюк. Великого открытия тут нет. Использовать такой инструмент для заточки ножей глупо..🤪 Отказываюсь от подписки. Всего наилучшего.
Oh Jesus H Christ ! If you have all those other fancy ass tools why the fuck wouldn’t you have a knife sharpener ! 🤣🤣🤣. Find a porcelain cup and use the bottom to sharpen the freakin knife ….
How to sharpen a knife i in an extremely stupid, lazy, and dangerous way. Seriously, people who post stuff like this should be banned from making videos for misleading the public and spreading bad information. PS - Just go buy an electric knife sharpener.
Lots of knives will be ruined trying this. Takes a steady hand, and a very specific steady angle. If you're new to sharpening, this may not be the technique to try with a knife you care about
You just need a light force and slow movement and it will be very easy
And if you get the edge too hot you'll change the temper of the steel and ruin the blade
Thank you! Cheers!
A flap disc is too coarse for this job they are mostly 60-100 grit you should be closer to 240 grit and 10,000 rpm is too fast you will create heat in the edge
@@creationholic101 what is the name of the equipment you used?
Thanks.
I'm from South Africa.
Welcome to Creation Holic channel! Hope you have a good time while watching the video
As soon as your blade heats up and changes color at all, your hardening and tempting are gonna. It will never hold an edge again. It might as well be scrap steel.
Angle grinders are WAY TOO FAST.
Hello! thanks for your comment. Wish you all the best!
good tips for life
Thank you for watching
Angle of knife should be 22° to get the best edge.
Thank you for sharing your feedback
👍🏼thanks for sharring❤
Thanks for watching!
it is very useful for me
Thanks for liking
رائع
Thank you! Cheers!
I thought the same thing. When I seen the sanding pad on the hand grinder. Mower blades are good & that's all I would do!! I paid a lot for my knifes!!!!
Glad you like them!
Great 👍
Thanks for the visit
Brasil sc.excelente.
Thank you! Cheers!
Don't ever do this, there is a guard on a grinder for a reason plus you will waste your knife , use a whetstone that's how it is supposed to be done
Thank you for sharing your feedback
From Malaysia.... support you bro👍👍👍👍👍
Thank you so much 👍
Shouldn't he have gone to the other side of the grinder for opposite side of the knife? How can he grind when the wheel is arriving on the knife edge. It should always be moving away.
Hello! thanks for your comment. Wish you all the best!
Thx for the idea! Grinding machine must be set to the lowest speed. Additionally, it is difficult to hold the knife at the correct angle - on both sides! The angle specified by manufacturers in Europe for chef's knives is almost always 15. If you sharpen the knife to an angle of 12, you will have to grind for quite a while because you have to grind away steel. Your idea is therefore only good for experienced people. There are simpler methods. Skully from Stuttgart, Germany
Just how many households have such a grinding machine at home?
@@ronyeap88 its an anglegrinder, not unusual to have, also, no speed settings and this is dangerous
Thank you for sharing your feedback. Have a good day!
Super!
Thank you! Cheers!
None of my angle grinders have a speed control they're all alone high speed which would really heat the edge and make it super easy to damage.
Thank you for sharing your feedback. Have a good day!
Good idea.
Thank you! Cheers!
Exelentes dicas 🇧🇷🇧🇷 fortaleza ceará Brasil
Glad you like them!
Thanks for sharing, great idea
Thanks for watching!
Love the idea. What was that second disc you used?
polishing disc
Oh .. razor skill !!
👍😄
Thank you for watching
good, but needs additional tools 👍
Thanks so much for watching our video. Wish you all the best
Pittsburgh, PA
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
In Tanzania this method was created more than 30 years
It's very good, isn't it?
Exelente 👍🇺🇾🧉🏍️ Uruguay
Hello! Welcome to Creation Holic channel! I am glad you like this ideas. Wishing you all good things!
India, Karnataka, Bengaluru
Welcome to Creation Holic channel! Hope you have a good time while watching the video
Harika iş 🙏🇹🇷
Thank you! Cheers!
日本です。日本の包丁は切れ味がよいです。また切れ味が悪くなっても3秒で切れ味を良くする「包丁研ぎ器」という道具も¥1000程度で買えるので 今回の動画は観て楽しむだけになりました。
Thank you! Cheers!
私もこれやっています。
it's amazing, isn't it?
How come it takes six minute video to display sharpening and knife family three minutes
Because U don't know how to slide forward.
Video content is a guide for people to do, if you do it it only takes 3 minutes
@@creationholic101 The video doesn't show how to sharpen the opposite side of the blade. When you turn it over the edge of the blade will dig into the flapper wheel. Just use sharpening stones and do it right.
😂
If I am not mistaken, I believe the video shows the knife blade being sharpened from both sides.
Also, I think there may be a little more time involved than just "3-minutes" to do this exercise---- but a training video (or even training someone in person) always takes more time than doing the actual job.
Other than that, I think it's a great idea for sharpening a blade---Thanks
.
Ez úgy marhaság ahogy van!
It's quite effective, try it and feel it
Se, após 15 dias, você "afiou" a faca, usando a ferramenta e produtos do vídeo, mas a faca ficou novamente cega, fale comigo. Sou fabricante e afiador de lâmias e te digo o que deu errado.....hahaha
👍😄
Can you share more about this issue?
I would say the issues is cause no coolant (water) was supplied during sharpening, thus overheating and weakening the sharpened thin Metal?!
Thank you! Cheers!
@@ekstremyst Boa sugestão. Está usando a lógica de forma correta.
This needs a half a thumbs up. Grinder is wrong!! Eats to much of your blades and or knife. What you really want is a belt sander. Lawn mower blades 3 swipes each side. Knife, maybe 2 swipes. So 5-10 seconds
Hello! thanks for your comment. Wish you all the best!
Amazing method… a fucking sharpening stone … a strop… I mean wtf? Get off my google ! Lol
que tipo de discos utiliza, espero respuesta, gracias
Flap Discs 100
Kept a kitchen knife at work for cardboard and whatever, sharpened it with a belt sander, it lasted 20 years, knives can handle much harsher conditions than what is generally shown in sharpening ,maybe not this, it would round the edge and make uneven cuts in the steel.
Thank you for sharing your feedback. Have a good day!
a sharp knife
Thank you for watching
Romania said hi, nice video.
Thank you for watching
Son medios demasiado agresivos para los cuchillos
Te durarán poco tiempo
Sou cuteleiro faço minhas facas na forja a carvão eu mesmo faço meus flaps até a lixa d'agua nr 1000 para amolar minhas facas.
Автор видео - фигляр, с такими ножами так не пойдет 🤝
Thanks for sharing!
Safety first , don't do that , DANGER for not experienced folks
Saludos desde Cananea, Sonora, Mexico
Welcome to Creation Holic channel! Hope you have a good time while watching the video
How much grinder RPM my friend? 😩
8,500rpm
How do I sharpen my knives if I don't have a grinder, from South Africa. I am a woman and don't have access to that tool
ruclips.net/video/K3RxuMWvREg/видео.html
I sharpen my knives at home with a typical dual grit sharpening stone. The technique takes a bit of practice but is not difficult. Plenty of videos on the net
Greece
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
Yo my guy, there's an invention called a whetstone for this exact purpose. Try it.
Thank you! Cheers!
Just a little dangerous 😅😅 Good luck at the ER
Thank you for watching
“ It will keel”
Youd have better luck just using a belt sander with high grit paper. Grinding the blde literally does just that...grind away.
Just buy a whet stone and sharpen your knifes the professional way.
Thank you! Cheers!
Супер, качественно и быстро. Но это только если руки из правильного места растут.😂
😂😂😂Thank you for watching
The first sanding disc is 100 grit. What is the second disc with the polishing compound? Also what is the purpose for cleaning with toothpaste at the end?
I typically use a 17° angle for my knives which is typical of Japanese knives.
I also use sanding belts and buffing wheels and precision guides even though I have many fine stones (...but, no time to work with them unless I am in the woods without electricity and a machine shop)!
buffing wheels and polishing wax
For removing any built up plaque from the knife.
If you don't pay attention with a sharpening stone, you know what you get? A messed up edge. If you don't pay attention with a grinder and a blade... who wants to answer?
Hello! thanks for your comment. Wish you all the best!
Fu**d knife
Narration please. How are we supposed to know what's going on!
❗Please enable subtitles in your language 🙋🏼♀ Thanks for watching 😋🤗😘
@@creationholic101ohhh... I see. Now I know what's going on 😊 thanks.
3 min schärfen in einem 6 min video
The video content is a tutorial, if you actually do it it will take less than 3 minutes
DO NOT DO THIS. This method will overheat the metal on a microscopic scale which will make the steel soft and it will not hold the sharp edge for very long and this permanently ruins the knife.
Hello! thanks for your comment. Wish you all the best!
Takes 6 minutes of video to demonstrate how to sharpen a knife in 3 minutes. Hmmm.
Video content is a guide for people to do, if you do it it only takes 3 minutes
This is dangerous to do to a grinder. That knife cud bite the disc and send it flying towards you.. not a smart way. Doing this could lead to serious injuries
Thank you for sharing your feedback and expressing your perspective
L'alta velocità può rovinare l'acciaio... smerigliatrice a velocità regolabile messa al minimo sicuramente meglio
Hello! thanks for your recommendation. Wish you all the best!
Seemed longer than 3 minutes 😂
The video content is a guide and if you do it, it will take less than 3 minutes
Grinder RPM looks slow
8,500rpm
Or you could just use a knife sharpener. My 10 dollar sharpener makes my knives razor sharp after 3 pulls through
Thank you! Cheers!
its effective but its dangerous.
i would suggest desktop mini grinder wheels they are far safer then this.
but it works and effective.
just very unsafe.
Hello! thanks for your comment. Wish you all the best!
Sharpen, my knives on the concret outside my door. No need to flaff around like this video.
Thanks for sharing!
Like to see you cut paper after that😊
It is not advisable to use a grinder without the guard. You should at least advise viewers the risk of doing so.
Hello! thanks for your comment. Wish you all the best!
O
Thank you for watching
I could of sharpened it on a steel before you even set up your bloody angle grinder!
Thank you for sharing your feedback and expressing your perspective
How to sharpen your knife in three minutes..... 6 minute video
The video content is a tutorial, if you do it it will take less than 3 minutes
👎 Начало видео, где давит на томат и конец, где режет с поступательным движением, это дешовый трюк. Великого открытия тут нет. Использовать такой инструмент для заточки ножей глупо..🤪 Отказываюсь от подписки. Всего наилучшего.
I'm sorry to hear that the video didn't meet your expectations. I appreciate you bringing this to my attention
@@creationholic101Не переживайте, из других видио я почерпнул много хорошего 😊
Too long time mate
The video content is a tutorial, if you actually do it it will take less than 3 minutes
Ok cool
No no no
Thank you for watching
Just get to the point of doing it ffs
Thank you for watching
Oh Jesus H Christ ! If you have all those other fancy ass tools why the fuck wouldn’t you have a knife sharpener ! 🤣🤣🤣. Find a porcelain cup and use the bottom to sharpen the freakin knife ….
Thank you! Cheers!
More like how to ruin a knife in 3 minutes
Can you give me more information?
How to sharpen a knife i
in an extremely stupid, lazy, and dangerous way.
Seriously, people who post stuff like this should be banned from making videos for misleading the public and spreading bad information.
PS - Just go buy an electric knife sharpener.
Please try and feel
Crap!
Please try it and accept it
@@creationholic101BS video. Accept this.
3 minutes my butt
The video content is a guide, if you do it it will take less than 3 minutes
Absolutely dumb, especially with 100 grit … don’t do it.
Please try and feel
Stupid idea, really dum video 😢
I'm sorry to hear that the video didn't meet your expectations. I appreciate you bringing this to my attention
Samarqanddan salom 👍👍👍🔪🪚⚒️🧲
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
I think i can do this too @thefirsthammer
Please try and feel