Ciao, I found your video, I had the same problem. My right light didn't work. I took the car apart, but still couldn't find the problem. After watching your video I found the connector melted a little, the metal in the connector was bend backwards. After fixing this problem with a small screwdriver my light worked again. I nearly went to the garage, now it saved me a big bill. You have no idea how releaved I am. Thanks again.
This is only a half and temporary solution to the lighting problem. To prevent contacts from burning out, two relays and two fuses must be added. The current lighting circuit will then control the relay coil and significantly reduce the thermal load on the contacts.
Acabo de hacerlo funcionan otra vez!!! Gracias ♥️ la verdad es que tal y como están las cosas no podemos permitirnos ir al taller para estas cosas... Me has salvado el mes 😂
We need God's help when starting somewhere with the PANDA 😊 I have a Panda from 1991 (0.75 fire engine), and recently when I turned the headlights switch the car jumps because of the load or it wont start if turned off. The turn signal was working not well recently, too - lightinng almost constantly and emitting strange noize. I guess it is some kind of short of both? Can you recommend what connectors to clean? Is it the earth cable which needs to be cleaned as on the videos about old car battery troubleshooting - headlights??
Putting a new connector and wires is not the permanent solution. the problem is sometimes the wires get to much voltage, and then it got to hot and melt. With this solution it will happen again. If you put a fuse between the wires, it wil blow the fuse and not melt the connector.
💛 Repairing kit here: amzn.to/2jSorUe
Ciao, I found your video, I had the same problem. My right light didn't work. I took the car apart, but still couldn't find the problem. After watching your video I found the connector melted a little, the metal in the connector was bend backwards. After fixing this problem with a small screwdriver my light worked again. I nearly went to the garage, now it saved me a big bill. You have no idea how releaved I am. Thanks again.
Thanks for your feedback 🙂👍 I'm happy to know it worked for you😊
This is only a half and temporary solution to the lighting problem. To prevent contacts from burning out, two relays and two fuses must be added. The current lighting circuit will then control the relay coil and significantly reduce the thermal load on the contacts.
Thank you for the information! 💪🏼❤️
How and where I should add them?
What kind or relay? Thank you!
great video ... now i know how to fix it😀👍god blessing u you and thanks again 👋😀
Thanks for your feedback 👌 ✌️
Thank you. Thanks to you, I knew where to find the plug.
Thank you for watching 💪💪
Un grazie enorme dall' Italia!!!!!
You are welcome!!💪❤
Thank you
Perdona tengo el mismo problema y también tengo la pieza derretida, a día de hoy aún tienes el panda ? Y siguen funcionando tus cortas ?
Ya no lo tengo pero estuvienro funcionando 2 o 3 años por lo menos
Acabo de hacerlo funcionan otra vez!!! Gracias ♥️ la verdad es que tal y como están las cosas no podemos permitirnos ir al taller para estas cosas... Me has salvado el mes 😂
Gracias por hacérmelo saber👌✌️
Great videos!!! I'll try now to fix it 😏
Thanks for your feedback 🤙💪
Gracias loco
We need God's help when starting somewhere with the PANDA 😊
I have a Panda from 1991 (0.75 fire engine), and recently when I turned the headlights switch the car jumps because of the load or it wont start if turned off. The turn signal was working not well recently, too - lightinng almost constantly and emitting strange noize.
I guess it is some kind of short of both?
Can you recommend what connectors to clean?
Is it the earth cable which needs to be cleaned as on the videos about old car battery troubleshooting - headlights??
Grazie Sono riuscito a riparare grazie a te
You are welcome 💪👍
Very good amigos!
Thanks for your feedback ❤💪
Gracias por el video y la solución
De nada! Gracias por dejar un comentario!!💪❤
Merci, thank you, i have same problem .i will look and try,
Thank Philippe for your feedback!
Muchas gracias por el video me ahorre 380 e visiten ala madriddddd
De nada👌✌️
Thank you bro👌
You are welcome! 💪🏼♥️
Nice bro
Thanks for your feedback 👌 ✌️
Salut nu mi se pune contactul învârt de cheie dar nimic curent are masina
Putting a new connector and wires is not the permanent solution.
the problem is sometimes the wires get to much voltage, and then it got to hot and melt.
With this solution it will happen again.
If you put a fuse between the wires, it wil blow the fuse and not melt the connector.
Thank you for your feedback!
Indeed, my wires are keeping melting
It didn't happened me yet. Let's see
@@GuyInAMountain I'm gonna go with the fuse now.
Non basta bisogna cambiare anche
Il devio luci completo