Can I Recover The Data? iPhone 11 That Died & No Longer Boots Up. DC Power Supply Tutorial.
HTML-код
- Опубликовано: 30 июн 2024
- Here is how to recover your data from an iPhone that does not turn on. This motherboard has a short circuit, which is causing no signs of life. So I show every step, in detail, how to diagnose the issue, repair it & get it fully functional, so we can recover the customer's data.
Do you need your data recovered? Send me a message for a quote: vccboardrepairs.com/contact
The first step is to isolate the motherboard & take it out of the housing. Any of the small parts plugged in could be the reason why it doesn't boot up.
Then we connect to the DC Power Supply, to check for shorts before prompt to boot & after prompt to boot. In this case, we had a 3A short BEFORE prompt to boot. This tells us we have a short on either:
1. VDD MAIN
2. VDD BOOST
or 3. Batt VCC
In this case, we found a short on VDD MAIN.
Then we use a thermal camera to try to track down where that short is. In this case, we were unable to pinpoint it directly, as it was either under a shield or inside the sandwich.
So I proceeded to split the sandwich to check inside, only to find the short was on the top side of the board, all along.
After removing the shield, we discovered the shorted capacitor.
We removed it & cleared the short.
Reballed the sandwich back together & got the phone fully functional!
Let me know in the comments, what you learned from this video!
Here’s the list of tools I used in this video:
⭐ USB A Meter: www.vccboardrepairs.com/usbAm...
⭐ USB Charger: www.vccboardrepairs.com/brick
⭐ 183C Leaded Solder Wire: amzn.to/4dthLS9
⭐ T20 Heater w/ iPhone X - 15 Plates: www.vccboardrepairs.com/heater
⭐ The BEST Solder Wick: amzn.to/49RpA16
⭐ Fluke Multimeter: amzn.to/3UwBIyK
⭐ KORAD DC Power Supply: amzn.to/45Qxjvc
⭐ Mechanic Boot Cable Box: www.injuredgadgets.com/mechan...
⭐ Dual Soldering Iron Station: amzn.to/47RV4Dt
⭐ JBC C210 Knife Tip: amzn.to/47RV7PF
⭐ Atten Hot Air Station: amzn.to/3tjYIYl
⭐ Microscope: amzn.to/48coNYN
▶Here are some other tools I have tested & fully recommend: www.vccboardrepairs.com/gear
▶Subscribe for more phone repair tool reviews & tutorials: ruclips.net/user/vccboardrep...
▶Need a repair? Or need to recover your data? Request a quote: www.vccboardrepairs.com/conta...
▶Useful Links◀
Crowdsourced repair solutions: repair.wiki/w/Repair_Wiki
Join my Locals Community: vccboardrepairs.com/locals-co...
30 Day Microsoldering Starter Course: vccboardrepairs.com/solder-co...
90 Day Advanced Solder Course: vccboardrepairs.com/90-day-co...
Buy a shirt: merch.vccboardrepairs.com
▶Phone Repair Videos◀
Microsoldering Repair Videos: • How To Fix iPhone 13 w...
Data Recovery Tutorials: • Where To Copy Your iTu...
Phone Repair Tool Reviews: • LIVE! iPhone 6S Plus O...
▶Best Thermal Cam Setup◀
Seek Compact Pro: amzn.to/34I4whX
Seek Stand: vccboardrepairs.com/buy-seek-...
Seek Macro Lens: www.vccboardrepairs.com/buy-m...
▶Social Media◀
Facebook Group: vccboardrepairs.com/vcc-fb-group
Facebook Page: / vccboardrepairs
Instagram: / vcc_board_repairs
TikTok: / vcc_board_repairs
▶About VCC Board Repairs◀
We are a Las Vegas, NV based repair shop who offers mail in repair services for microsoldering repairs & data recovery. Our specialty is iPhone, iPad, Samsung and other mobile devices. We also offer B2B pricing for repair shops. Contact us today for a quote: www.vccboardrepairs.com/conta...
▶Affiliate Note◀
This page contains affiliate links. If you choose to make a purchase after clicking a link, I may receive a commission at no additional cost to you. Thank you for your support!
Do you need your data recovered? Send me a message for a quote: vccboardrepairs.com/contact
Hi, I had tried the link and says"account suspended"
@@beavisjj Unfortunately, my website is experiencing an issue & i'm actively working on it right now to fix it. If you're in the USA, you can text me for a quote: 702-670-2711
I've never seen a video of a dead mobile with 0.00amp draw on usb meter . Could you please share , what could be the problem?
Excellent and clear work, well done
You are really good working...I like it
Excellent work. Thank you for sharing.
I really appreciate your support. Thank you so much
I always watch your best video thanks ❤
Thank you! Appreciate the support!
You work amazingly it's very nice to watch you. Can you do videos on how to replace charging ports and connectors on the board
I have many videos on this topic. Search my channel to find them 😀
Great job Jesse!!!
Your support means a lot, thank you!
As always Jesse... # 1 🎉❤
My pleasure! Happy to hear you're enjoying my channel!
Good work boss thank you
Thank you! Appreciate the support!
You've earned a loyal viewer!
Thanks for sticking around, you're awesome!
Good Job
Thank you! Appreciate the support!
Another good repair, Thanks for the video.
In my experience, I have repaired quite a few iPhone 11 boards, mainly for that no signal issue that stems from certain caps on 2-3 specific lines shorting or partial shorting causing it to be searching all the time, but that aside, I have found that those boards are very heat sensitive, they use 138 solder from the factory so, you only need to go to about 150c or so to split it safely. I found that sometimes if I reballed them with 183 instead of 138 and I had to heat the board to 200c to have the half's solder back together, I found in about 1/5 cases, the baseband would end up with cold solder. However, using a good quality 138 solder, and heating to 150c i found in over 100 iPhone 11's I have never had a cold solder issue under the baseband and issues related to the bottom board again. It just kinda scared me when you heated it up at the start so hot.
On another note. When it comes to removing that plate, I find it is much safer to just use a rotary tool of some sort, and as long as you are very careful not to press too hard, or scratch the board or any components, it works very well. I guess the only trade off is, you have no plate left to solder back on there.
Yes, I've been fixing these for years on a regular basis. I understand how to handle the heat on them. Never had an issue as you described.
To each their own
@@VCCBoardRepairs Absolutely, To be clear, I wasn't criticizing your work, You do a very professional job, I have been watching for a long time now, I have seen the quality of your work.
I think there are a lot of technicians out there who watch these videos to learn how to solder, and I think it is important to share our stories and experiences so that after they have watched the video, they can read the comments and perhaps be encouraged to share their own
To be honest the issues I was referring to are long term, say 3-6 months down the track. A lot of the devices I repair have been sold, and come with warranty for 1-2 years, which is where I can see the issues come back over time, in the short term there is no issues to worry about.
Any way, as I said the first time, Another great repair, Thanks for the video. And I will add too, Please keep making more, I love to see them
Good video ❤
I have a similar issue! iPhone 14 Pro Max shut down suddenly why it was 3% charge I am wondering what the issue might be and if you guys can fix it ! Now it’s not turning on or charging and also I had issues charging it with a third party cable from apple
Yes! We specialize in board repairs, as you can see in my video. Send me a message for a quote: www.vccboardrepairs.com/contact-us
What blade brand do you use to remove the underfill?
I personally use quian li mega idea brand but literally any x-acto or similar blades work well.
jesse i want to buy sugon 8610dx hot air station do you recommend me to buy please
Quick 861dw best
I've never used that. I prefer the Atten ST-862D over the Quick 861DW
there are no links to tools in the description in the new youtube layout?
There is. On desktop, it's on the right side
@@VCCBoardRepairs when i click on more it shows description, transcript and few links to your youtube homepage. there is almost nothing. no other info. i must me doing something wrong. i am desktop. youtube layout changed yesterday. im going to investigate more. thanks for reply. i think youtube eFd something.
I need nand programmer which one will you recommend for me
JC V1S Pro
@@VCCBoardRepairsthat’s too slow
super reparation
Thank you! Cheers!