Alright Tony, as a PA boy, with another PA boy over here in the UK, come on over to England and do an on-location video of “Stay Tuned.” Hell, I’ll even pay for your airfare. The English engine/Foxbody combination has me intrigued. That said, we are just a couple of Pennsylvania boys and a British mate, with Foxbody Mustangs doing the impossible over here; restoring, rebuilding and drag racing with the logistic pains of being overseas.
That single tube in the motor mount, I'd add a second tube underneath. The single tube looks like it's almost horizontal. Not a good situation. Amazing that it fits, and they make a bell housing for it? Nuckin Futz. Great works guys. Can't wait to see the next episode.
The T-56 was used in aston v12s from at least ‘99-‘06. Dodge, Cadillac, Chevy, Ford, Pontiac, and Holden have used this transmission from the factory in their cars. It’s an incredibly common transmission for “sporty” cars and trucks.
A tip for clearing tunnels and bashing sheet metal in, use a 4x4 as a chisel and hammer it on the surface, it will make a lot more room in a cleaner way, with almost no hammer marks. That thing is gonna be awesome.
quote: Initially Martin and Sox were competitors, but Martin approached Sox to drive his car after concluding that he just couldn't beat him. Sox drove a 1963 Chevrolet and then a factory-sponsored A/FX Mercury Comet in 1964. In 1965, he drove an altered-Wheelbase Plymouth. so,fox and martin is safe as these 2 drove all the big three.good tribute
I was one of the "it's never going to fit" crowd. I can't tell you how happy I am to be proven wrong - this is one of the best hot rodding projects you've ever done, Tony & crew! Unique always wins when everyone else is doing the same old, easy-peasy engine swaps and builds.
I was right there with ya. I know how tight those engine bays are to begin with. They still have a lot of hurdles to jump. At least they have the main one cleared.
@@MikeAnderson-uj3oo Even though they have some massive issues to deal with, I'd say the remaining hurdles are next to nothing (though I would have tried a K-member that supports coilovers in order to hack out the shock towers for throttle body clearance). If there's a bellhousing, there will be a flywheel and clutch, and the remaining bits to make it workable are nothing in comparison to the job they just achieved. Plus, since they had to low-mount the rack, they should be able to avoid the bump steer issue by using the later spindles - relatively easy issues to overcome. The only thing I'm concerned about are engine mounts. I don't trust how far out they're cantilevered, or the thickness of the mounting plate. That's the only obvious point of failure that I'm seeing at the moment.
@@earlbrown They can hack the core support and install one slightly angled, C4 Vette style. They can go full Porsche and run a pair of radiators on either side of the fenders - and given Tony's experience with a 996s - including having PowerKraut on hand as a reference - doing that wouldn't be too difficult either. So many ways to make this happen. The intake is the only concern I still have. Does the "other" intake bolt up as the internet claims it will, will it drive the build cost way up, and will it provide the clearance necessary?
Ya, needs a bigger baseplate to spread out the force and 2 more supports. maybe after the headers are figured out then rework the mounts. awesome build!!!
Yeah that base plate was a little scrawny looking. I'd put a thicker longer plate bolted where it currently is, with an extra part sticking forward. Triangular gusset under the arm to the plate hanging out over that space . Maybe some back support.
I've owned several Ford era Jaguars. The biggest issue I encountered on almost every one was the wiring. Mechanically, they are built tough. And yes, I do know I'm talking about Jaguar. Like Jeremy Clarkson said once, an Aston is basically a Jaguar in a party frock. In the situation you guys are in, you will no doubt be using an aftermarket, stand alone, wire harness. So you will be able to eliminate all the issues they are notorious for. I will be honest, I really had doubts that you we're going to shoehorn that monstrosity in place. Good job boys. And Tony.
Lol that's me right now I have a 197,000 mile jaguar XKR from 2002. The engine is incredibly solid but some wiring harnesses for the throttle body are corrupted so I have to replace them
Please keep that chain hoist, my father was a expert old school machanic, i remembered his shop always had a chain hoist taking out engines ect, great memories i had listening to that sound , brought back huge memories as a kid watching him tear into cars , he had no fear to fix them . My father was awesome and i see that in you! Never change buddy ok!!@
Fun fact, the reason things seem to good to be true on availability for conversion parts is because the 6.0 v12 from Aston was a ford design utilizing the 3.0 duratec v6 block as starting point. They literally duplicated the casting end to end to make a v12
no, the block is completely different in design with deep skirt and no girdle. it has its own bellhousing the reason it has a magnum upgrade bellhousing is because it came with a t56 from the factory.
This brings me back to wrenching on Fox bodies as a daily hobby! Having all the 5.0 mods, there’s no way we would have done this back in the 80’s/90’s. But with the “modern” engine swap options, this just makes crazy sense. (Emphasis on CRAZY) Fun to watch all your project videos!
Tony's bro his body language is like nope, this ain't going to work or fit. If I didn't see it with my own eyes I wouldn't have believed it. Crew stabbed that thing in like it was stock.😮
A line I used to use a lot is "I hate when people tell me something is impossible, especially while I'm doing it!" While crowded, that would still fit on a T-shirt.
South Bend Clutch might be able to match up a clutch set, they told me they have a cross reference of what works with what and can provide a solution for whatever your trying to accomplish.
Thats basically two ford v-6 put together. And basically a ford v-6 bellhousing bolt pattern. So not too wild, unlike what you guys are doing. Can't wait to hear that thing rip. Best car channel on RUclips!
I had the same color, same year fox, had some “mechanic” fix the struts as I didn’t have welding experience (it came out about as bad as yours), I had to sell it after putting a ton of work into it because I had move out of my apartment after getting dumped. For a split second I thought this was my fox that yall ended up with when I saw those strut towers haha. I will own one of these again, sick video !
I will agree 1000%. I am so sick of LS swaps. And right behind that is body swaps. Taking an old body and sticking it on a modern car. Whatever happened to guys building their own chassis ? I just don't see the enjoyment in that. Maybe because I have built a few complete cars myself. Small block Chevette, 4x4 Elcamino, Mid engine VW van, Rear engine Ford Courier pick up, These were all complete hand fabricated chassis. No sticking a body on top of something else.
Right? Don't get me wrong, I understand why people do LS swaps. Easy to find and easy to make power with but they're everywhere. That's why I'm wanting to go with a 8.1 swap in my obs Chevy. Not unheard of but still not an LS swap.
Simply Stunning! I absolutely love this build, Tony! I can’t say enough about it but I’ll try. This embodies the true spirit of hot rodding, just like the vets did on the dry lake beds after they returned home from WWII. Speaking of “dub’ya, dub’ya TWO,” as my beloved grandpa used to call it, I’m reminded another well known Mustang that benefited greatly from a British V-12 swap, the fighter aircraft that served as inspiration for Lee Iacocca’s original Ford Mustang: the P-51! Not sure if you realized it, Tony, but you just stumbled upon my dream custom build with significant historical heritage. I instantly envisioned a bright silver paint job with air brushed panels and rivets in a direct nod to the P-51D, with an old school olive drab interior with stacks of aviation gauges, levers, and canvas or leather bomber seats? My imagination is running wild with names like “LOW LEVEL ‘STANG” or, since it was the Rolls-Royce designed engine that completely transformed the Mustang into a real world beater, just straight up call it “MERLIN!” One last thought- if you route the exhaust out the front fenders to resemble the aircraft, paint some nose art of a dark haired, bosomy pinup girl in knee-high socks and not much else, name her “SIMPLY STUNNING” as she is on my tattoo and you can consider me at the top perspective buyers. Please! My wife may divorce me but I’d go into debt for the opportunity to own this direct link to aviation and automotive history. Don’t call me crazy, just crazy enthusiastic.😂
I dont know if Ive seen a better looking swap in a foxbody, those intake runners and the way it sits down in there looks amazing! I also like the history between the two companies which has even carried on to newer care like the front grille of a ford fusion looking like an Aston, etc. it all makes perfect sense to do this swap, while also making none at all, thats what rodding is about. I cant wait to hear this thing roar and see how you tackle to tuning, electrical.
These Aston V12’s are bullet proof. Have many clients with 100k miles on them. Only thing they are known for is going through plugs and coils. We’ve been using the Amazon coils successfully and they are 1/4 the price.
I went the opposite way years ago. Long before anyone was doing engine swaps. I put a Chrysler engine - transmission and rear-end into a British sports car. Four wheel disc brakes. Six Konis. All braided lines. One reason I can appreciate your work. Great episode. My new favorite thing to look forward to on a Friday. Worked on my BMW, came in and watched this.
@@stephencurry8552 oooh. I really didn't expect that. Wasn't expecting it to be an XJS either. Honestly, glad I asked. That's awsome. 😎 Any chance you've any footage of it?
A friend of mine just finished rebuilding one of those motors, inside they're just 2 V6 Mondeo motors... But they do go well and they do sound awesome...
You shouldn’t have had too widen the trans tunnel on your 83 s10 to do the 350/350swap cause I didn’t have to when I did mine back in 2012 the only thing I had to do was notch the floor because I decided to slap a hurst ratchet shifter in it since I had line lock and a trans brake
This is what engine swaps were back in the day to see what crazy combinations they came up with. Hot Rodding the old school way love this. Shove the biggest engine into the smallest car 🚗
HellYeah Tony! Let’s see what the Aston Mustang can do. Fun projects like this keep me coming back. Gotta think of a clever James Bond name for it. Beer and a Slice Time! Ready to Stay Tuned🤘🤘🔥🔥🔥
@@StayTunedTA I grew up watching Powerblock TV and Stacey David would always have like a cart with all the new parts they were putting on the project that was totally product placement. Throwing the old parts off the bench is the final Powerblock TV touch
What a cool project! Not to give you any bad ideas, but Nobel has done wonders strapping turbos to this engine's V6 sister. Just an idea! Call it the Asstang 😂
Tony and his guys are BADASS , V8 Porsche , Sike clone p/u , 55 Chevy , drift car , sleeper Lincoln and now a killer Mustang !!! . I think BANGERS & SMASH would be a great name lol . Cheers 🇨🇦
you guys are great!! I have a tedious and frustrating job to do on my truck today and every time I need I break so I don't start throwing things, I come in and watch you guys grinding away on this project and it gets me motived to go back out to the garage and endure more punishment.
Thank God you've chosen a manual transmission ! EVERY CHANNEL GOES WITH THE AUTO TRANS ! In a few short years the stick will disappear into the night...thank you for putting up a fight ! WHY NOT THE "TKX?'
delusional, it needs brilliant exhaust they developed the system many many years ago. or the brazillian secret weapon exhaust that successful on doing that recently
That’s a FoxTon of motor in there . “full of pizza and full of hope” is my motto in the garage as well lol should definitely be a shirt with like the new hope Star Wars font and count me in for one lol .
I don't understand why youtube dosen't suggest different videos more I had no idea about this channel till the collaboration with Derek but I'm glad I found it eventually
From 1999 to 2006 the Lincoln LS was available with a 3.0 l v6 with a manual transmission. The Aston Martin V12 was built from the 3.0 l v6 molds. Therefore the rest of the rear of the engines are the same. The flywheel and clutch from the Lincoln engine will bolt up to the crank on the V 12. I have seen both engines and when you look at them from the rear you can't tell the difference. Ford would use all the same dimensions as they already had the main parts. I don't think the clutch would be able to handle the torque oh the V 12 but it would be a start. Hope this helps. Good luck.
Tony will definitely reach one million subscribers. I share and tell everyone I can about he's channel. That's what everybody needs to do SPREAD THE WORD
I remember in my younger days someone said that Engine (Hemi) won't fit in that car, 1966 Chevy II, WRONG! I wish I still had the pictures! Stahl made the headers for it! (East Carnegie, Pa.)
That is one nice, "Mostly Adequate" V12 install! I worked on Astons for a few years. I feel your pain. But you will LOVE the way it sounds when yer done!
Dudes!! Mad props!! Just saying it... V-12 Mustang!! Ahhhhh.... I found myself saying several things at diff. points. 1) They're gonna have to cut that firewall out to let that monster roam: remains 2b seen! 1a) They're gonna end up w a 13" driveshaft!! 2) Gonna have to cut that trans tunnel: True! 3) Don't like the angle of the dangle! (motor mounts) need gussets! 4) Still have major hurdles: room for accessories, Rad, fans, steering shaft, Master cyl, (maybe under floor or electric?) HEADERS!! Carnac says: (answer): I see a LOT of Fab in your future!! All that said?? "DAMN THE TORPEDOS"!! FULL SPEED AHEAD!! Brakes?? WE DON'T NEED NO STINKING BRAKES!! BRAKES ARE FOR QUITTERS!! GODSPEED GENTLEMEN!! BE CAREFUL!!!
The fitment of that reminds me of my buddy’s old S13 that had an RB26 in it. It was shoehorned in there for sure! I remember we had to hammer a small dent in the core support to clear the crank pulley.
I think I ordered that car your working in 1989. It had a special anniversary badge on the passenger side dash Ang a removable sunroof. Brings back memories
I remember when David Fryberger was putting the LS in the van and he had that plastic mockup engine. That would be awesome to have right now doing this project.
As tight as it is for headers you guys should look up swapping out that rag joint for a borgeson u-joint. Was into Fox Mustangs back in the late 90's/early 2k's. Even wrote tech articles for a local Mustang website. LOVE what you guys are doin'!
Right on QA1 Tubular SubFrame!! This one is gonna be Rad! Fun!! I agree with Fox & Martin. Also with a revisit in about 4 months to a year with hop upgrades. Sweet Bridgeport, we use those at QA1.
Tony, I recommend you put grease fittings into all the urethane bushing mounts so you can grease them, that’s what I do with mine. We all know how badly these urethane bushings squeak and you’re adding in several squeak points.
I love the antique crane/hoist being used, but gotta put an electric hoist on her. The chains dragging on body's gives me chills. It'd be around $15k fully installed to that original crane, which I know is literally a project. But so worth it. Maybe at 500k subs :)
With so many cowl hood options for foxbodies available I wouldn't worry too much about good clearance. Great work as always, although I question the longevity of those mounts but I could be wrong.
Specs on the 2001 5.9L is 420 HP @ 6000rpm. So if you can do some intake and exhaust work you could get 450 out of her. Going to be a blast to drive. High rpm screamer.
This is going to be epic! This channel needs to get to 1,000,000 subs. One of the best car shows on youtube.
Easily the best and most unique.
Yup
Agreed, we just need a few episodes with Lucky.
This might just get it there. Cool build for sure
You needed a name. Try this. Aston Farten'. Shitin' n gittin'!
Need a shirt that says "we're gonna need a bigger shop"..😂
Man, we DO.
This needs all the upvotes
😂yes definitely
with Chiefy and jaws on it
@@StayTunedTA we need a shirt that says somthing about the pizza
V12 noise out of a Foxbody is going to be absolutely Wild! and thanks to your engine donor and whoever developed that bellhousing
Straight pipes or equal length headers?
@@CorePathway thats brilliant exhaust , not some BS straight pipes
When it runs putting anything English into anything means you're going to spend alot of time in the shop, good thing they have one
@@CorePathway Equal length 100%
Alright Tony, as a PA boy, with another PA boy over here in the UK, come on over to England and do an on-location video of “Stay Tuned.” Hell, I’ll even pay for your airfare. The English engine/Foxbody combination has me intrigued. That said, we are just a couple of Pennsylvania boys and a British mate, with Foxbody Mustangs doing the impossible over here; restoring, rebuilding and drag racing with the logistic pains of being overseas.
Another shirt worthy quote, " they said we were idiots... They weren't wrong about that...". Love watching you guys push the bounds of lunacy.
fox and martin.........sounds sick,and a funny throwback to the old days of hotrodding and drag racing
is it sacrilege though? For a non-Mopar?
They did race Fords also before mopar
@@StayTunedTA they raced Fords before Mopar
Name the car Saucy crumpet.
@@StayTunedTAthe whole thing is kinda wacky. You could paint it even like one of the Sox and Martin cars.
Tony, you definitely need to call it The ASstang!!!!
Absolutely I was thinking the same thing.
Also thinking the same😂
Me too!💯👍✌️
I should have read your comment first. Well damn. lol
Astang Martin
That single tube in the motor mount, I'd add a second tube underneath. The single tube looks like it's almost horizontal. Not a good situation.
Amazing that it fits, and they make a bell housing for it? Nuckin Futz.
Great works guys. Can't wait to see the next episode.
My exact thoughts about those motor mounts.
That engine is based on the Ford 4.6, that’s why there’s a bellhousing for it.
@@Mike-Honcho-yep ford v12
Yes that looks sketchy as hell
The T-56 was used in aston v12s from at least ‘99-‘06.
Dodge, Cadillac, Chevy, Ford, Pontiac, and Holden have used this transmission from the factory in their cars. It’s an incredibly common transmission for “sporty” cars and trucks.
A tip for clearing tunnels and bashing sheet metal in, use a 4x4 as a chisel and hammer it on the surface, it will make a lot more room in a cleaner way, with almost no hammer marks. That thing is gonna be awesome.
quote: Initially Martin and Sox were competitors, but Martin approached Sox to drive his car after concluding that he just couldn't beat him. Sox drove a 1963 Chevrolet and then a factory-sponsored A/FX Mercury Comet in 1964. In 1965, he drove an altered-Wheelbase Plymouth. so,fox and martin is safe as these 2 drove all the big three.good tribute
I was one of the "it's never going to fit" crowd. I can't tell you how happy I am to be proven wrong - this is one of the best hot rodding projects you've ever done, Tony & crew!
Unique always wins when everyone else is doing the same old, easy-peasy engine swaps and builds.
I was right there with ya. I know how tight those engine bays are to begin with. They still have a lot of hurdles to jump. At least they have the main one cleared.
@@MikeAnderson-uj3oo Even though they have some massive issues to deal with, I'd say the remaining hurdles are next to nothing (though I would have tried a K-member that supports coilovers in order to hack out the shock towers for throttle body clearance). If there's a bellhousing, there will be a flywheel and clutch, and the remaining bits to make it workable are nothing in comparison to the job they just achieved. Plus, since they had to low-mount the rack, they should be able to avoid the bump steer issue by using the later spindles - relatively easy issues to overcome.
The only thing I'm concerned about are engine mounts. I don't trust how far out they're cantilevered, or the thickness of the mounting plate. That's the only obvious point of failure that I'm seeing at the moment.
I didn't see a whole lot of room for a radiator.
@@earlbrown They can hack the core support and install one slightly angled, C4 Vette style. They can go full Porsche and run a pair of radiators on either side of the fenders - and given Tony's experience with a 996s - including having PowerKraut on hand as a reference - doing that wouldn't be too difficult either. So many ways to make this happen.
The intake is the only concern I still have. Does the "other" intake bolt up as the internet claims it will, will it drive the build cost way up, and will it provide the clearance necessary?
Those mounts need gussets for strength. Great job Tony.
Yes, please. At least one more brace. There's a lot of length and odd angles. I don't trust them.
Agreed 100%
Ya, needs a bigger baseplate to spread out the force and 2 more supports. maybe after the headers are figured out then rework the mounts. awesome build!!!
Yeah that base plate was a little scrawny looking. I'd put a thicker longer plate bolted where it currently is, with an extra part sticking forward. Triangular gusset under the arm to the plate hanging out over that space . Maybe some back support.
Yeah, they look engineered to shear clean off or at least bend downward very soon
I've owned several Ford era Jaguars. The biggest issue I encountered on almost every one was the wiring. Mechanically, they are built tough. And yes, I do know I'm talking about Jaguar. Like Jeremy Clarkson said once, an Aston is basically a Jaguar in a party frock.
In the situation you guys are in, you will no doubt be using an aftermarket, stand alone, wire harness. So you will be able to eliminate all the issues they are notorious for. I will be honest, I really had doubts that you we're going to shoehorn that monstrosity in place. Good job boys. And Tony.
Lol that's me right now I have a 197,000 mile jaguar XKR from 2002. The engine is incredibly solid but some wiring harnesses for the throttle body are corrupted so I have to replace them
Cardboard Assisted Design is the only "CAD" most of us shadetree guys have access to. Great work gentlemen!
Please keep that chain hoist, my father was a expert old school machanic, i remembered his shop always had a chain hoist taking out engines ect, great memories i had listening to that sound , brought back huge memories as a kid watching him tear into cars , he had no fear to fix them . My father was awesome and i see that in you! Never change buddy ok!!@
I work for Tremec. Never been prouder so see my company name. Can’t wait to see this thing rip.
Fun fact, the reason things seem to good to be true on availability for conversion parts is because the 6.0 v12 from Aston was a ford design utilizing the 3.0 duratec v6 block as starting point. They literally duplicated the casting end to end to make a v12
no, the block is completely different in design with deep skirt and no girdle. it has its own bellhousing
the reason it has a magnum upgrade bellhousing is because it came with a t56 from the factory.
@@xalty1200you two are talking about two different engines. Technically. But you're both right... And wrong. . .
I can’t believe you crammed TWO Duratec V6’s under that hood!
You had me at "V12 in a Mustang".🍻
This brings me back to wrenching on Fox bodies as a daily hobby! Having all the 5.0 mods, there’s no way we would have done this back in the 80’s/90’s. But with the “modern” engine swap options, this just makes crazy sense. (Emphasis on CRAZY)
Fun to watch all your project videos!
Tony's bro his body language is like nope, this ain't going to work or fit. If I didn't see it with my own eyes I wouldn't have believed it. Crew stabbed that thing in like it was stock.😮
A line I used to use a lot is "I hate when people tell me something is impossible, especially while I'm doing it!" While crowded, that would still fit on a T-shirt.
South Bend Clutch might be able to match up a clutch set, they told me they have a cross reference of what works with what and can provide a solution for whatever your trying to accomplish.
Thank y'all for a different swap into a fox. I'm super excited for this build and it already looks like a beast.
Juice
Thats basically two ford v-6 put together. And basically a ford v-6 bellhousing bolt pattern. So not too wild, unlike what you guys are doing. Can't wait to hear that thing rip. Best car channel on RUclips!
so a flywheel and clutch setup for this may have to be aftermarket sourced Mondo V6 maybe? 8 bolt crankshaft though
I had the same color, same year fox, had some “mechanic” fix the struts as I didn’t have welding experience (it came out about as bad as yours), I had to sell it after putting a ton of work into it because I had move out of my apartment after getting dumped. For a split second I thought this was my fox that yall ended up with when I saw those strut towers haha. I will own one of these again, sick video !
This is SO much better than yet another LS swap!
I will agree 1000%. I am so sick of LS swaps. And right behind that is body swaps. Taking an old body and sticking it on a modern car. Whatever happened to guys building their own chassis ? I just don't see the enjoyment in that. Maybe because I have built a few complete cars myself.
Small block Chevette,
4x4 Elcamino,
Mid engine VW van,
Rear engine Ford Courier pick up,
These were all complete hand fabricated chassis. No sticking a body on top of something else.
Right? Don't get me wrong, I understand why people do LS swaps. Easy to find and easy to make power with but they're everywhere. That's why I'm wanting to go with a 8.1 swap in my obs Chevy. Not unheard of but still not an LS swap.
YEAH!! WHAT HE SAID!!! EFF THE LS!!! 😆😂🤣
Tony call it the ASTON-MUSTING DISVANTAGE!
I really appreciate the lift safety callouts, not everyone thinks about that stuff.
Simply Stunning!
I absolutely love this build, Tony! I can’t say enough about it but I’ll try. This embodies the true spirit of hot rodding, just like the vets did on the dry lake beds after they returned home from WWII.
Speaking of “dub’ya, dub’ya TWO,” as my beloved grandpa used to call it, I’m reminded another well known Mustang that benefited greatly from a British V-12 swap, the fighter aircraft that served as inspiration for Lee Iacocca’s original Ford Mustang: the P-51!
Not sure if you realized it, Tony, but you just stumbled upon my dream custom build with significant historical heritage. I instantly envisioned a bright silver paint job with air brushed panels and rivets in a direct nod to the P-51D, with an old school olive drab interior with stacks of aviation gauges, levers, and canvas or leather bomber seats? My imagination is running wild with names like “LOW LEVEL ‘STANG” or, since it was the Rolls-Royce designed engine that completely transformed the Mustang into a real world beater, just straight up call it “MERLIN!”
One last thought- if you route the exhaust out the front fenders to resemble the aircraft, paint some nose art of a dark haired, bosomy pinup girl in knee-high socks and not much else, name her “SIMPLY STUNNING” as she is on my tattoo and you can consider me at the top perspective buyers. Please! My wife may divorce me but I’d go into debt for the opportunity to own this direct link to aviation and automotive history. Don’t call me crazy, just crazy enthusiastic.😂
I dont know if Ive seen a better looking swap in a foxbody, those intake runners and the way it sits down in there looks amazing! I also like the history between the two companies which has even carried on to newer care like the front grille of a ford fusion looking like an Aston, etc. it all makes perfect sense to do this swap, while also making none at all, thats what rodding is about. I cant wait to hear this thing roar and see how you tackle to tuning, electrical.
Thank you again for playing Subtastics. We are headed to York, PA soon. Pizza is on us.
-Martin Ford-sese
-King Henry (Henry Ford)
-The Dragoon (British Cavalry, also has “drag” in the name)
-Fish n Rips
-Winston
The Name is Bondo, Jimmy Bondo. Best I could come up with🤣🤣🍺🍕
HAHAH, I was jus doing that. Bond, Hydra Bond.
@@StayTunedTAHow I spent the first 15 of the video. 🤣🤣 Shoutout to ya, Barb, and Zimmie kid. It’s a great one so far🤘🤘
Built ford tough with Aston stuff
@@StayTunedTA Double Oh NO
@@StayTunedTAname the car Saucy crumpet.
These Aston V12’s are bullet proof. Have many clients with 100k miles on them. Only thing they are known for is going through plugs and coils. We’ve been using the Amazon coils successfully and they are 1/4 the price.
Cant wait to see Tony drift the wheels off this thing
I went the opposite way years ago. Long before anyone was doing engine swaps. I put a Chrysler engine - transmission and rear-end into a British sports car. Four wheel disc brakes. Six Konis. All braided lines. One reason I can appreciate your work.
Great episode. My new favorite thing to look forward to on a Friday. Worked on my BMW, came in and watched this.
🤔 was it an XJS?
@@3xeplodng_3agle_studios No, it is a 1965 TR-4
@@stephencurry8552 oooh. I really didn't expect that. Wasn't expecting it to be an XJS either. Honestly, glad I asked. That's awsome. 😎
Any chance you've any footage of it?
@@3xeplodng_3agle_studios No, just photos. I have had no need to video anything.
Fox & Martin is hands down the best name. Do it! You could do a shirt with a gentleman butler filling up the fox with a jerry can.
20:36 “I bet ya that doesn’t come off”
This repeatedly makes me laugh
A friend of mine just finished rebuilding one of those motors, inside they're just 2 V6 Mondeo motors... But they do go well and they do sound awesome...
Love the Tavarish clip, where yet again Tony drives MUCH faster than his passengers are comfortable with.
Love this build boys!!! Pro tip: air hammer makes the tunnel widening job A LOT easier!!! Had to do that when I put a 350/350 in a 83 S10.
You shouldn’t have had too widen the trans tunnel on your 83 s10 to do the 350/350swap cause I didn’t have to when I did mine back in 2012 the only thing I had to do was notch the floor because I decided to slap a hurst ratchet shifter in it since I had line lock and a trans brake
Thank you for preaching a bit of safety Tony
This is what engine swaps were back in the day to see what crazy combinations they came up with. Hot Rodding the old school way love this.
Shove the biggest engine into the smallest car 🚗
Man, this is one Hot Toddy Fox Body
Loving the build and STOKED they had the bellhousing in existence
HellYeah Tony! Let’s see what the Aston Mustang can do. Fun projects like this keep me coming back. Gotta think of a clever James Bond name for it. Beer and a Slice Time! Ready to Stay Tuned🤘🤘🔥🔥🔥
Thanks bud! Kick your feet up and crack that brew! Fox and Martin? Aston Powers?
@@StayTunedTAAston Powers got me. Ha ha ha.
Tony you nailed it with Aston Powers!
@@StayTunedTA Martin Ford?
Double O Uh Oh
I love the build! It's like some of the combinations I've dreamed up over the years. Can't wait to hear it run.
22:40 OH SHIT! He's got the table with the new parts on it. Power block vibes lol
Hahaha, it always scream Fast and Furious to me!
@@StayTunedTA I grew up watching Powerblock TV and Stacey David would always have like a cart with all the new parts they were putting on the project that was totally product placement. Throwing the old parts off the bench is the final Powerblock TV touch
You gotta love the old Power Block days. It was like a two hour long commercial for new parts.
Tony, Fox & Martin is it! This is one of your coolest builds!
Love it what do you think of Austang murtin !!
What a cool project! Not to give you any bad ideas, but Nobel has done wonders strapping turbos to this engine's V6 sister. Just an idea!
Call it the Asstang 😂
You and Lucky built a twin engine Impala. Of all the crazy projects on youtube, this is one I KNOW is gonna run and be awesome!
Tony and his guys are BADASS , V8 Porsche , Sike clone p/u , 55 Chevy , drift car , sleeper Lincoln and now a killer Mustang !!! . I think BANGERS & SMASH would be a great name lol . Cheers 🇨🇦
Also a great name. Good idea 🍻
@@djk91lx28 hahaha thanks , I also thought maybe Toad on the Road lol 😆. Cheers 🇨🇦
@@mikepoint4717 you sir are far more creative than I. Awesome names.
I've been waiting to see this epic build 🙌
HA, same, we waited on drivetrain parts for awhile.
That engine is the size of the car! It’s going to be so cool. 👍 You will have to remove the 5.0 badges and get some V12 badges to take their place.
Dropping a V12 into anything makes it epic.
you guys are great!! I have a tedious and frustrating job to do on my truck today and every time I need I break so I don't start throwing things, I come in and watch you guys grinding away on this project and it gets me motived to go back out to the garage and endure more punishment.
Thank God you've chosen a manual transmission !
EVERY CHANNEL GOES WITH THE AUTO TRANS ! In a few short years the stick will disappear into the night...thank you for putting up a fight !
WHY NOT THE "TKX?'
more gears more better
Manuel harder to steal !!! LOL😅Hot Rods should have manuel and grocery getters need auto !!!JMHO !!
You mean hotrods with manuals and grocery getters named Manuel?
😂@@Drmcclung
@@jasonbirch1182 If you like stick, get a Manuel?
Love it!!! Can't wait to hear it rev out... Definitely needs X-pipe no muffler 🤪
Damn right , x pipe , and maybe some black widows
Mufflers and electric exhaust cutouts Sleeper style !!!
delusional, it needs brilliant exhaust they developed the system many many years ago. or the brazillian secret weapon exhaust that successful on doing that recently
Yes sir cram that motor in there!
I love how the lighting and camera angles used remind me of the old shows I used to watch on speed channel.
Absolutely killer in the best way!
This project is so awesome. Finally something, that is 100% outside the box! Can't wait to see more episodes of this AsStang. 🤘
That’s a FoxTon of motor in there . “full of pizza and full of hope” is my motto in the garage as well lol should definitely be a shirt with like the new hope Star Wars font and count me in for one lol .
I support this tshirt idea
Ooooh man, this is gonna be sweet. Cue the pizza!
Thanks! Appreciate it!
They need to keep track of how many pizzas it takes to finish each car. Obviously the more pizza, the more difficult it was.
I love when you put non-traditional motors in caes. This car is going to turn some heads with the sound. Keep up the great work!!!!
The hole saw on the Bridgeport ... priceless 😂
DB5.0
Going to be nuts!!
YES! V12 POWAH!!!
Let's go!
You are a mad lad and I love this project! I am so glad it fits.
I don't understand why youtube dosen't suggest different videos more I had no idea about this channel till the collaboration with Derek but I'm glad I found it eventually
If I didn't see this video with my own eyes. I wouldn't have believed it. Fox body with a v12. Bravo gentleman.
From 1999 to 2006 the Lincoln LS was available with a 3.0 l v6 with a manual transmission. The Aston Martin V12 was built from the 3.0 l v6 molds. Therefore the rest of the rear of the engines are the same. The flywheel and clutch from the Lincoln engine will bolt up to the crank on the V 12. I have seen both engines and when you look at them from the rear you can't tell the difference. Ford would use all the same dimensions as they already had the main parts. I don't think the clutch would be able to handle the torque oh the V 12 but it would be a start. Hope this helps. Good luck.
Taking ls swap to the next level. I freaking love it. If you dont....you need to see a doc asap. Something wrong.
Tony will definitely reach one million subscribers. I share and tell everyone I can about he's channel. That's what everybody needs to do SPREAD THE WORD
Dude! Awesome project, love every bit of it. Been following since HRG, you rock and I love the raw youtube stuff!
I remember in my younger days someone said that Engine (Hemi) won't fit in that car, 1966 Chevy II, WRONG! I wish I still had the pictures! Stahl made the headers for it! (East Carnegie, Pa.)
That is one nice, "Mostly Adequate" V12 install!
I worked on Astons for a few years. I feel your pain. But you will LOVE the way it sounds when yer done!
Dudes!! Mad props!! Just saying it... V-12 Mustang!! Ahhhhh.... I found myself saying several things at diff. points. 1) They're gonna have to cut that firewall out to let that monster roam: remains 2b seen! 1a) They're gonna end up w a 13" driveshaft!! 2) Gonna have to cut that trans tunnel: True! 3) Don't like the angle of the dangle! (motor mounts) need gussets! 4) Still have major hurdles: room for accessories, Rad, fans, steering shaft, Master cyl, (maybe under floor or electric?) HEADERS!! Carnac says: (answer): I see a LOT of Fab in your future!! All that said?? "DAMN THE TORPEDOS"!! FULL SPEED AHEAD!! Brakes?? WE DON'T NEED NO STINKING BRAKES!! BRAKES ARE FOR QUITTERS!! GODSPEED GENTLEMEN!! BE CAREFUL!!!
Another reason i have 2 newer Mustangs. One being 04 SVT Cobra terminator (4900orig mis). Hard to beat these cars!
Y’all are truly living out your dreams. Wild car builds. Pizza and cold snacks with friends. Then making money from it is the cherry on top 🍻🍻 Gents
The fitment of that reminds me of my buddy’s old S13 that had an RB26 in it. It was shoehorned in there for sure! I remember we had to hammer a small dent in the core support to clear the crank pulley.
guess I started watching this before and am now coming back to you guys where you're doing the trans tunnel massaging...I'm hooked now, lol
I think I ordered that car your working in 1989. It had a special anniversary badge on the passenger side dash Ang a removable sunroof. Brings back memories
I remember when David Fryberger was putting the LS in the van and he had that plastic mockup engine. That would be awesome to have right now doing this project.
Thanks!
Its impressive to watch someone who knows what they're doin.
Doesn’t look out of place. Shocked it looks so good. Intake is so sick
This is one of the sickest swaps ever
Awesome build! You all should get a "Sine Bar" for your mill it will help out with the angle cuts.
As tight as it is for headers you guys should look up swapping out that rag joint for a borgeson u-joint. Was into Fox Mustangs back in the late 90's/early 2k's. Even wrote tech articles for a local Mustang website. LOVE what you guys are doin'!
Right on QA1 Tubular SubFrame!!
This one is gonna be Rad! Fun!!
I agree with Fox & Martin. Also with a revisit in about 4 months to a year with hop upgrades. Sweet Bridgeport, we use those at QA1.
I find this channel to be mostly adequate. No scratch that. Substantially adequate. ❤
Tony, I recommend you put grease fittings into all the urethane bushing mounts so you can grease them, that’s what I do with mine. We all know how badly these urethane bushings squeak and you’re adding in several squeak points.
I love the antique crane/hoist being used, but gotta put an electric hoist on her. The chains dragging on body's gives me chills. It'd be around $15k fully installed to that original crane, which I know is literally a project. But so worth it. Maybe at 500k subs :)
My favorite RUclips build to date. Can’t wait to see it all come together!
With so many cowl hood options for foxbodies available I wouldn't worry too much about good clearance. Great work as always, although I question the longevity of those mounts but I could be wrong.
You should fab new badges from 5.0 to 6.0. Might be a cool subtle change to the fox body. :) This is an awesome build. Love watching.
Awesome build! Waiting tirelessly for the next episode.
Good stuff!, keep em coming Tony. Your channel keeps getting better with every episode!.
I love this project. That engine is going to sound crazy coming out of the old foxbody. It will definitely be unique 👌
Specs on the 2001 5.9L is 420 HP @ 6000rpm.
So if you can do some intake and exhaust work you could get 450 out of her. Going to be a blast to drive. High rpm screamer.
We used to eat cake like that all the time... awesome good. Loving the swap guys, keep up the good work and details!