I have no need for an aquarium chiller - I'm just here to catch a glimpse of Leon! But I have to say that this was a fascinating and educational video. And it was very enjoyable to watch. I bet you could make a video about changing a tire look enjoyable! Great job!
I also came here to see Leon and see how he has grown since molting. I also hope that the Tony lobster that I am keeping will soon molt to remove the scars on its body.
Refrigeration tech here. The condensing coil on most modern fridges run along the outside walls of the unit. I'm thinking you got really lucky in not popping one. That unit also has a flammable refrigerant, just felt you should know. Over all, I think this diy is really smart. It should work well for a long time I suspect.
The little guys just have the coils as he showed in the video. Even "active coolers" normally just have one cold wall and you can generally feel where it is.
@@TheBrokenLife He showed the freezer's evaporation coil in the video, it's the condensation coil that's around the outside, but you can feel the warmth. They're usually bonded to the outside metal shell to radiate heat efficiently. And yes, flammable refrigerant happens a lot, which is why there's a large label about it. Big refrigerators have an larger condensation coil with a fan, so their walls are mostly insulation and the occasional wire. My thought was to put it on a stand and go in/out the bottom, which tells you how paranoid I am of the walls...
@@jameswyatt1304 I'd have to watch it again, but I'm used to seeing the condenser right by the compressor with a little fan on it, even on the big guys. Deep freezers would be where I'd expect to see a "warm skin". Oh well... Nothing venture, nothing gained, and it worked out in the end.
I'm not a refrigeration tech but by looking at the copper going up from the back of the unit into the side walls 5:45 I was concerned with his thought process. If you'd like to answer my question though, would it make a difference to the cooling rate overall if he put spacers between the coils? I'm thinking it would be more effective if the metal was being cooled equally on each circumnaviation of a coil, rather than, as is, where the metal to metal touches. It might not, of course, because the metal, once filled with cold water would just cool itself. Thanks. And yes, good build, and opened my eyes, to diy processes.
@@ValeriePallaoro spacers and a fan to move air over them will make the temperature transfer more efficient for sure. However doing that would increase BTU load on the system and might overwhelm that units capacity.
As suggested by The Broken Life, you need to grommet where the hoses pass through the metal cabinet. The vibration of the compressor, along with the sharp edge of the hole in the sheet metal will eventually saw through the tubing. While actual passthrough grommets are ideal, one possibility is to force silicone rubber caulk in and around the hole. This will cushion and trap the tubing in the hole, thereby eliminating the sawing motion of the vibration.
@@ValeriePallaoro You still need a grommet or bead of caulk to prevent the sawing motion. The stainless steel tubing would take longer to saw through, but any time you have an "edge" like a hole in sheet metal, you need to ,either bond or grommet. Look at the firewall in your car (sheet metal wall between the engine and interior) every wire or hose is grommeted or bonded.
@@bobcraig3827 I think he can get away with it this time... The hose fits snugly and its got the insulation and plastic to support it from digging into the metal... If there was no insulation I'd agree with you....
I came here for Leon, I'm staying for your interesting projects and very chill attitude, voice and editing style, which is such a refresher in this era of flashy and in your face media. Keep up the good work! :)
This was an interesting build! 👍 If you revisit this chiller in the future, I'd recommend taking that stainless coil down to a hydraulic shop and having the ends flared so the hose is less likely to ever come loose or leak. I'd also suggest bulkhead fittings on the pass-through locations on your fridge so you have less of a chance of abrasion ever wearing through the hoses, improved air sealing, and less foam exposure (Cabinet foam is extremely flammable. That cyclopentane (analogous to butane) sticker on the back is a warning that the foam is literally full of it). I'd also consider putting the pump on a moisture sensing outlet and routing the hoses above the height of the tank (maybe they already are?) so they could never siphon it empty. I use a 5/8" siphon hose to transfer fuel from cans into my vehicles and the flow rate is is about 1.25 gallons/minute with about a 24" fall. If heat gain through the hoses becomes an issue, pipe insulation is pretty readily available and reasonably inexpensive. It's worth seeking out the stuff with a rubber outer shell that has an adhesive sealing flap. The stuff HD usually carries is just foam with a barely glued lip. The rubber stuff also doesn't "hate" being spray painted so you could somewhat make it match your decor.
Don't hesitate to get your Leon merch. I just got my Leon mug and I love it. Should have got two because I have a sneaky suspicion my husband might steal it, I've seen the way he is eyeing me down as I drink my morning coffee. Thank you Leon, I'll think of you everyday now.
Brady you did such a good job! i first saw this concept about 30 years ago in the aquarium room of my biology teacher. he used the same method to cool down an mediterranean aquarium im summer.
Came for Leon, didn't expect to see Leon. Was pleasantly surprised by Leon and listened to the entire thing in the background with 0 intention of ever needing a chiller XD. Good times were had.
I love DIY projects! This doesn't look too hard for anyone with any skill level to pull off. It's an interesting project. I had fun watching you make it! ☺️
I've been watching Brady's vids since day one of Leon and it just now dawned on me: his voice is nearly the same as the narrator of "How its Made." Good luck getting that out of your head, viewers.
A man showing off something he is passionate about. This is 'youtube back to basics' when money came second and the will to show something that makes you happy came in first hand. Money is the driving force for 99,99% of youtubers today.
I enjoy your videos so very much! They keep me interested, entertained, and educated… and your narration is especially soothing. I lost my rat terrier a year ago last week and Leon has become a little joy and therapy to look forward to. Keep up the fantastic work and I look forward to many more videos! ❤️
... we can all live through this Leon the Lobster ... he has such an angle in his keeper ... blessings to your unique family ... and ... yes ... please keep these video's coming we love Leon for many reasons ...
Fairly new viewer here, (Leon Fan) Love your smooth and easy delivery, I could listen to you narrating tying your shoes. If I didn't know any better I'd say you were Bruce Brown (Endless Summer).
I've got 2 of those same Craftsman drills from my Dad. I used them when I was a kid 45 years ago and they are just as brutally strong today as they were back then!
@@ggburnitup4055 They're a tad noisy, but not as bad as even today's cheap drills. They are powerful... if you have the side handle attached, I've sheared off quarter inch lag bolts driving them into oak. Bolt quit, drill didn't.
@@ggburnitup4055 No problem. They are bigger and a bit clunkier than a brand new Milwaukee or Bosch corded drill, but it's also 50 years old and still taking names!
Started this video to support the Chanel. i put videoes with Leon On when i fall asleep, and have to put the same video on several times to see the end. So started this one just to support but ended up enjoing it. So smart!
Brady, this was an awesome DIY. I would like to suggest, just for a little more efficiency, some spacers in the coils to allow air to pass between them more easily. I may be wrong as your refrigerator environment may be rather static in regards to airflow, but thought I would suggest it anyway as I suspect a coil spacer would be relatively cheap and easy to find.
The metal coil should be immersed in water inside the fridge, remember that air is an insulator so the current setup isn't efficient whatsoever. The fridge then cools the water and it acts like a heat sink, look up home brewing and distilling and you'll understand. The temperature of the fridge can be set much higher thus it won't run constantly and waste electricity.
I was wondering just about this. Maybe a shortened 5 gallon bucket with a hole in the bottom for the lower pipe and then caulk / aquarium sealant around it. I think the water would make the heat transmission MUCH more efficient, like when you add a couple gallons of water to the iced down beer in the cooler to really get it cold fast.
Maybe not the most effective way, but sure a fun way. Since air is great insulator, and the fridge is filled with air, you need a lower temperature in the fridge the if it was filled with water. If you want to be even more cost effective, there are probably a lot of second hand fridges, ppl tend to get new when changing up the kitchen and fully working ones end up on the second hand market. Lastly, i love these videos. The production is great and your voice is relaxing and nice. I'd like audiobooks read by you.
Note to self, Brady's finger is the same as a 5/8 drill bit. LOL you're a super interesting guy! And you're the only man I've ever seen that knows how to use a dustbuster! 😍😍😍😍😍 😆😆😆😆😆
Omg I needed this idea so bad, Ive looked into aquarium chillers for hydroponics and this is the way! Thank you!! I found you with your wholesome lobster video and the algorithm gave me this! Genious! 1/3 - 1/2 price of chiller and a useful fridge. Good tip that a full fridge/freezer is more efficient than empty too.
I wish I would have seen this a few years ago. Maybe Scarface would have made it. Let me explain. So I worked in a grocery store and wanted to rescue a lobster that we had for weeks. Apparently people were picky about eating a lobster that had a scar on its head. Not sure how it got there but needless to say he was the only one left week after week after several replenishments. Scarface was the perfect name for the fellow on death row. There was hope. I wanted to purchase him and take him to the ocean but here in Florida that would of been another death sentence. So I thought about an aquarium but well that was pricey. That along with keeping the aquarium at a low temperature was another problem. Long story short, I went in for my shift one day and found that someone didn’t mind the scar. Thanks for saving Leon and for the learning experience you gave me. Wish I would have done the same. RIP Scarface.
You’re are truly skilled my guy. Really enjoyed this DIY and it is amazing to think how many things it could actually be used for. Thank you so much. Love you guys.
Nice little build, I've been thinking of doing something similar to this for home brewing for a while. A small electric fan to circulate the air around inside the fridge will help with heat transfer.
Every time I go to toss out a new suggestion you come around and do the thing before I have a chance to open my mouth. Fantastic work man, brilliant little bit of thinking with that DIY setup as well!
Nicely done! I love projects like this because I’m always thinking of small improvements and tinkering with it! Joey Mullen (before he started vlogging) would be proud!
Have you thought of keeping the coil submerged in a bucket in the fridge? Maybe it could help with the thermal transfer and cool down the large tank more efficiently. Just a though and cool project.
@@LHyoutube I thought that's what you were referring to. About 20 years ago I was really into pc builds but could never afford it. I remember PC World magazine showcasing custom water cooling rigs. They were awesome looking and allowed for some crazy overclocking at the time.
Probably some insulation on the external tubing and perhaps making the internal coils run around the inside of the fridge instead of just staying in the middle would increase the effictiveness, but this is a great project with very little effort. Wonderful work!
If anyone is planning on trying this they can call manufacturers of the fridge for information on where wiring and tubing is in the fridge, also the inlet and outlet pipes can be insulated for better results ( I worked in both Aquarium and refrigerator industries ) Keep the updates coming on Leon, They are very interesting and your delivery is excellent.
I'm currently working on building a paludarium for some Kaiser newts, and seeing that I live in the scorching central valley in CA, I'll definitely need to get a good chiller for these cold-loving amphibians. Though I'll probably just end up buying a prefabricated chiller, the idea of building one from scratch is certainly intriguing. I might try this project myself once I have a bit more experience under my belt; I'm not a very handy person, and I'm sure I'd find a way to screw this up somehow if I tried it now.
Read all the (well, not all of them, of course) comments. There are some very good tips to add to the functionality of this build, use a second hand fridge (cost reduction) where to site your drill holes (safety) grommet your tube holes (reduces wear and tear on the plastic) don't take out the drip tray (otherwise freezer drip water into the main area of the fridge) There's a hella bunch of knowleagable people in the comments section. Though, my thought is no Kaiser newts in central vally CA, (they are stunning, tho) I'm sure some warm loving species would be kinder (I can't imagine how I'd feel if my cooling system broke down on 'em) Be brave. DIY is really all about failure until you get it right.
Nicely done! You can also increase it's effectiveness buy insulating the clear tubes externally. The more insulation, the less strain on the compressor. I had used a long freezer (a GE I believe) and dedicated most of the right side of it for my 45 gallon tank chiller. It worked well (dropped the temp on average of 15 to 18 degrees in a fairly warm basement) and I had plenty of space left over for other frozen goods to boot, so it was a nice thing to do all around. Say hi to Baxter and Leon for me!
I built one for my 100 gal tank with a much smaller refrigerator and a dinky coil compared to yours , the only difference is my coil is submerged in a bucket of water ! The water temperature is almost a constant temp with no fluctuations when the refrigerator kicks on and off..
@@wayne-oo Not terrible. I'm shooting for at least 50 to get me through the summer. My fridge gets as low as 22 degrees F. Think I can make it work?? I'm on the fence in pulling the trigger on a chiller.
Leon became the luckiest Lobster in the world when you stepped into his life...or into the Seafood Mkt. Hooray for your new creation, Leon's new water cooler. Great job! (Btw Zoomies, ref. Ader Farm Great Pyrenees guard dog).
As a failsafe, I'd add a thermostat to shut down the fridge incase it gets too cold. I'm not sure how sensitive he will be to temp swings but a lot of inverts are. Overall a great job!
Aluminum tape with insulation tape around the outlet tube could help keep temperatures down even lower, also seal the holes on the refrigerator with foam fill let’s get that thing chilling
This was a well thought out project that is affective and cost controlled. I suppose you could even add a filtration system into the hose to remove suspended particles from the water of needed, requiring less time vacuuming the substrate. Leon is going to one cool lobster on those hot summer days! Great job..I think you are spoiling him...LOL
It is an interesting concept and build but I'm curious to see how long the compressor lasts in the refrigerator. They aren't really designed for a constant heat source and instead for short bursts and maintaining the fridge at a specific temp.
@@EbolaxMonkey It's still going to kill the fridge in a few years, at least when in a warm climate. This concept is the equivalent of leaving the fridge door open all day.
If you live near or in a college town, these types of mini fridges are up on second hand sites like CRAZY this time of year! You could save yourself an extra $100 bucks by buying a second-hand fridge!
Great project, you are relying on the air flow within the fridge to circulate around the stainless coil, you could increase the cooling capacity by adding a low voltage fan to blow the cool air through the coil, you can buy usb powered fans from Amazon with speed control for a few dollars.
It's super calming to just watch DIY projects when done correctly, like this, other times the person is doing those '5 minute DIY' stuff that just is plain stupid considering their usually making something that's already kind of easy, to be harder
We need Leon!~ We need Leon!~ We need Bradys description of how Leon is doing! Please get Leon a side by side aquarium filled with other fish, so he thinks he has other aquatic things around him. Or better yet he needs a flat screen tv that projects happy life at the bottom of the Ocean.
I have no need for an aquarium chiller - I'm just here to catch a glimpse of Leon!
But I have to say that this was a fascinating and educational video. And it was very enjoyable to watch. I bet you could make a video about changing a tire look enjoyable! Great job!
I'm just waiting to see him smothered in butter!
I also came here to see Leon and see how he has grown since molting. I also hope that the Tony lobster that I am keeping will soon molt to remove the scars on its body.
@@redditstoriesrelationshipsusa Yes! More rescue lobsters 😍🦞
@@jagboy69 I'm thinking you'll be waiting for a very long time!
@@nancycowell-miller4321 at least until the algorithm changes or people get bored watching a lobster in a tank.🥴
Refrigeration tech here. The condensing coil on most modern fridges run along the outside walls of the unit. I'm thinking you got really lucky in not popping one. That unit also has a flammable refrigerant, just felt you should know. Over all, I think this diy is really smart. It should work well for a long time I suspect.
The little guys just have the coils as he showed in the video. Even "active coolers" normally just have one cold wall and you can generally feel where it is.
@@TheBrokenLife He showed the freezer's evaporation coil in the video, it's the condensation coil that's around the outside, but you can feel the warmth. They're usually bonded to the outside metal shell to radiate heat efficiently. And yes, flammable refrigerant happens a lot, which is why there's a large label about it.
Big refrigerators have an larger condensation coil with a fan, so their walls are mostly insulation and the occasional wire. My thought was to put it on a stand and go in/out the bottom, which tells you how paranoid I am of the walls...
@@jameswyatt1304 I'd have to watch it again, but I'm used to seeing the condenser right by the compressor with a little fan on it, even on the big guys. Deep freezers would be where I'd expect to see a "warm skin".
Oh well... Nothing venture, nothing gained, and it worked out in the end.
I'm not a refrigeration tech but by looking at the copper going up from the back of the unit into the side walls 5:45 I was concerned with his thought process. If you'd like to answer my question though, would it make a difference to the cooling rate overall if he put spacers between the coils? I'm thinking it would be more effective if the metal was being cooled equally on each circumnaviation of a coil, rather than, as is, where the metal to metal touches. It might not, of course, because the metal, once filled with cold water would just cool itself. Thanks. And yes, good build, and opened my eyes, to diy processes.
@@ValeriePallaoro spacers and a fan to move air over them will make the temperature transfer more efficient for sure. However doing that would increase BTU load on the system and might overwhelm that units capacity.
If only all dads treated their kids as well as you treat Leon ❤
Best lobster 🦞 Dad ever ❤️
Random comparison...you clearly have a story in your life to suggest this, and I'm sorry that you have xx
You should let them discount the fridge as a scratch and dent you could have saved even more money.
Speak for yourself
No kidding.
I like this!!! Chill your beer and fish!
As suggested by The Broken Life, you need to grommet where the hoses pass through the metal cabinet. The vibration of the compressor, along with the sharp edge of the hole in the sheet metal will eventually saw through the tubing. While actual passthrough grommets are ideal, one possibility is to force silicone rubber caulk in and around the hole. This will cushion and trap the tubing in the hole, thereby eliminating the sawing motion of the vibration.
I was thinking to push the coil ends through the wall and then do all the connections externally. Would that negate the need for grommets?
@@ValeriePallaoro You still need a grommet or bead of caulk to prevent the sawing motion. The stainless steel tubing would take longer to saw through, but any time you have an "edge" like a hole in sheet metal, you need to ,either bond or grommet. Look at the firewall in your car (sheet metal wall between the engine and interior) every wire or hose is grommeted or bonded.
@@bobcraig3827 I think he can get away with it this time... The hose fits snugly and its got the insulation and plastic to support it from digging into the metal... If there was no insulation I'd agree with you....
@@bobcraig3827 it's not sawing through stainless steel dude.
@@EikottXD Saw through the TUBING.
dude
Nothing stops you from.keeping Leon happy and healthy and I'm SO HERE FOR IT💙💙!!
I came here for Leon, I'm staying for your interesting projects and very chill attitude, voice and editing style, which is such a refresher in this era of flashy and in your face media. Keep up the good work! :)
This was an interesting build! 👍
If you revisit this chiller in the future, I'd recommend taking that stainless coil down to a hydraulic shop and having the ends flared so the hose is less likely to ever come loose or leak. I'd also suggest bulkhead fittings on the pass-through locations on your fridge so you have less of a chance of abrasion ever wearing through the hoses, improved air sealing, and less foam exposure (Cabinet foam is extremely flammable. That cyclopentane (analogous to butane) sticker on the back is a warning that the foam is literally full of it).
I'd also consider putting the pump on a moisture sensing outlet and routing the hoses above the height of the tank (maybe they already are?) so they could never siphon it empty. I use a 5/8" siphon hose to transfer fuel from cans into my vehicles and the flow rate is is about 1.25 gallons/minute with about a 24" fall.
If heat gain through the hoses becomes an issue, pipe insulation is pretty readily available and reasonably inexpensive. It's worth seeking out the stuff with a rubber outer shell that has an adhesive sealing flap. The stuff HD usually carries is just foam with a barely glued lip. The rubber stuff also doesn't "hate" being spray painted so you could somewhat make it match your decor.
For christ sake.... Its a chiller for aquarium water... Its fine the way it sits...lmao....
Don't hesitate to get your Leon merch. I just got my Leon mug and I love it. Should have got two because I have a sneaky suspicion my husband might steal it, I've seen the way he is eyeing me down as I drink my morning coffee. Thank you Leon, I'll think of you everyday now.
Brady you did such a good job! i first saw this concept about 30 years ago in the aquarium room of my biology teacher. he used the same method to cool down an mediterranean aquarium im summer.
Came for Leon, didn't expect to see Leon. Was pleasantly surprised by Leon and listened to the entire thing in the background with 0 intention of ever needing a chiller XD. Good times were had.
I love DIY projects! This doesn't look too hard for anyone with any skill level to pull off. It's an interesting project. I had fun watching you make it! ☺️
Ya ok…. No some people are just not capable in certain things , I’m one of those people , kudos to you for being you
plz Watch Video. DIY Aquarium Chiller By New_Aquarium_Hobby.
I've been watching Brady's vids since day one of Leon and it just now dawned on me: his voice is nearly the same as the narrator of "How its Made."
Good luck getting that out of your head, viewers.
A man showing off something he is passionate about.
This is 'youtube back to basics' when money came second and the will to show something that makes you happy came in first hand. Money is the driving force for 99,99% of youtubers today.
Leon hit the Jackpot when you rescued him. He one lucky lobster 🦞
Probably better odds in the lottery actually
*He IS...
(English for Beginners, Lesson 01)
You are a genius you showed kids how to be empathic and a scientist at the same time! I love Leon!
Helping Leon keep his COOL!
😁
So glad leon is here for us to document! Lobsters are so neat, unique, and amazing. Leon has really grown, and us viewers have learned to love him!
What a lucky lobster Leon is to have such a caring guardian! Peace and blessings.
I enjoy your videos so very much! They keep me interested, entertained, and educated… and your narration is especially soothing. I lost my rat terrier a year ago last week and Leon has become a little joy and therapy to look forward to. Keep up the fantastic work and I look forward to many more videos! ❤️
Hello 👋 Lana
How are you doing today
... we can all live through this Leon the Lobster ... he has such an angle in his keeper ... blessings to your unique family ... and ... yes ... please keep these video's coming we love Leon for many reasons ...
Is it just me or do all his videos give off a peaceful dream like vibe?
Fairly new viewer here, (Leon Fan)
Love your smooth and easy delivery, I could listen to you narrating tying your shoes. If I didn't know any better I'd say you were Bruce Brown (Endless Summer).
So happy to see Leon doing so well🥹
Hello 👋 Leslie
How are you doing today
I'm so glad you put bottles of water in the fridge! The whole time I was hoping you would
I've got 2 of those same Craftsman drills from my Dad. I used them when I was a kid 45 years ago and they are just as brutally strong today as they were back then!
I kinda wanna know how useful they were
@@ggburnitup4055 They're a tad noisy, but not as bad as even today's cheap drills. They are powerful... if you have the side handle attached, I've sheared off quarter inch lag bolts driving them into oak. Bolt quit, drill didn't.
@@kleetus92 thank you this is helpful especially since I'm doing more practical work in high school where I work with machines
@@ggburnitup4055 No problem. They are bigger and a bit clunkier than a brand new Milwaukee or Bosch corded drill, but it's also 50 years old and still taking names!
Started this video to support the Chanel. i put videoes with Leon On when i fall asleep, and have to put the same video on several times to see the end. So started this one just to support but ended up enjoing it. So smart!
That was cool and great choice of beer, Stella my favorite 😄
Hello 👋 sugaree
How are you doing today?
This is awesome! Thanks for the info and tell Leon we say hi
Leon is looking good! Rich color!
Thank you for the "how to" video! And of course ....thanks for saving and filming Leon❤️😇
This man is very smart and very creative! Well done, you’re continuing to make Leon feel more and more at home! 🙂
IMPRESSED: The most I could've done is pick up the fridge! Love ya Leon: You got a Great Papa! deb in Sunny SC🕶
was not sure about this set up until you stored additional things in the fridge like food for the aquarium, i got sold.
Brady, this was an awesome DIY. I would like to suggest, just for a little more efficiency, some spacers in the coils to allow air to pass between them more easily. I may be wrong as your refrigerator environment may be rather static in regards to airflow, but thought I would suggest it anyway as I suspect a coil spacer would be relatively cheap and easy to find.
I came for Leon and stayed for the DIY. I love your ingenuity!
The metal coil should be immersed in water inside the fridge, remember that air is an insulator so the current setup isn't efficient whatsoever. The fridge then cools the water and it acts like a heat sink, look up home brewing and distilling and you'll understand. The temperature of the fridge can be set much higher thus it won't run constantly and waste electricity.
I was wondering just about this. Maybe a shortened 5 gallon bucket with a hole in the bottom for the lower pipe and then caulk / aquarium sealant around it. I think the water would make the heat transmission MUCH more efficient, like when you add a couple gallons of water to the iced down beer in the cooler to really get it cold fast.
or at least increase the thermal mass by having a jug of water sitting inside the coil. A mini cooler jug might be perfect fit.
I'm honestly surprised more people haven't pointed this out
@@sebastianwhalin743 they don't teach physics in high school anymore, there's no time left after gender studies and CRT
Wow. Really impressed! I know nothing about the process , but really admire what you are doing for Leon ! You are awesome!
Maybe not the most effective way, but sure a fun way. Since air is great insulator, and the fridge is filled with air, you need a lower temperature in the fridge the if it was filled with water.
If you want to be even more cost effective, there are probably a lot of second hand fridges, ppl tend to get new when changing up the kitchen and fully working ones end up on the second hand market.
Lastly, i love these videos. The production is great and your voice is relaxing and nice. I'd like audiobooks read by you.
You saved a ton of money with your diy project.
Hello 👋 Cheryl
How are you doing today?
Note to self, Brady's finger is the same as a 5/8 drill bit. LOL you're a super interesting guy! And you're the only man I've ever seen that knows how to use a dustbuster! 😍😍😍😍😍 😆😆😆😆😆
😅😅😅👈
Wow this is by far your best video yet, keep up the awesome work! Your voice reminds me of watching how it's made when I was younger
Omg I needed this idea so bad, Ive looked into aquarium chillers for hydroponics and this is the way! Thank you!! I found you with your wholesome lobster video and the algorithm gave me this! Genious! 1/3 - 1/2 price of chiller and a useful fridge. Good tip that a full fridge/freezer is more efficient than empty too.
Such a great solution, Leon is one lucky sea-bug!
I wish I would have seen this a few years ago. Maybe Scarface would have made it. Let me explain. So I worked in a grocery store and wanted to rescue a lobster that we had for weeks. Apparently people were picky about eating a lobster that had a scar on its head. Not sure how it got there but needless to say he was the only one left week after week after several replenishments. Scarface was the perfect name for the fellow on death row. There was hope. I wanted to purchase him and take him to the ocean but here in Florida that would of been another death sentence. So I thought about an aquarium but well that was pricey. That along with keeping the aquarium at a low temperature was another problem. Long story short, I went in for my shift one day and found that someone didn’t mind the scar. Thanks for saving Leon and for the learning experience you gave me. Wish I would have done the same. RIP Scarface.
The best part was the ice cold beer in the fridge at the end! Very cool build. Can’t wait for the next Leon update!
I could so go a Stella right now!
Seems like an awesome diy for future axolotl owners, including myself!
I like me a cold Stella too! Great work, very impressive design!
You’re are truly skilled my guy. Really enjoyed this DIY and it is amazing to think how many things it could actually be used for. Thank you so much. Love you guys.
Nice little build, I've been thinking of doing something similar to this for home brewing for a while. A small electric fan to circulate the air around inside the fridge will help with heat transfer.
Every time I go to toss out a new suggestion you come around and do the thing before I have a chance to open my mouth. Fantastic work man, brilliant little bit of thinking with that DIY setup as well!
Good job, somewhere around 1/3 - 1/2 price and it stores beer! It's so good Leon did a solo on castanets at the end!
Very cool, I'm glad it all worked out buddy. We'll done, I'm sure the fish and/or Leon will love the cooler water
hey! Brady! keeping more beer cool is always a must and, keeping a hot lobster cool in the process that's a bonus!!
Wow this is amazing, thanks sir for this video. So much cheaper and more practical.
Nicely done! I love projects like this because I’m always thinking of small improvements and tinkering with it! Joey Mullen (before he started vlogging) would be proud!
Will never have a saltwater tank, a need for a heat exchanger or a pet lobster and loved every minute of this video
You are very crafty! Great freezer 👍
This video made me finally realize who you remind me of, at least your voice. How it’s made!
This was great! I'd love some more motorcycle content too. I really enjoy your film making style.
That project is really cool. I've always relied on throwing ice blocks in bags in the tank during the summer.
Thank you for this! Answers my question about required temperature.
Awesome project and thank you for doing the best u can for Leon
Have you thought of keeping the coil submerged in a bucket in the fridge? Maybe it could help with the thermal transfer and cool down the large tank more efficiently. Just a though and cool project.
Any chance you're a custom PC builder? 😂
@@LHyoutube Nope, I just like to tinker and build my own stuff when possible.
@@davej652 - Oh OK, it was mainly a joke as water-cooling is a big trendy thing in the custom build PC community 😀
@@LHyoutube I thought that's what you were referring to. About 20 years ago I was really into pc builds but could never afford it. I remember PC World magazine showcasing custom water cooling rigs. They were awesome looking and allowed for some crazy overclocking at the time.
@@davej652 - Overclocking Leon would be cool, imagine the size of his zoomies! 😂
We're making one too...Cowabunga.! Hello Leon. We love you.
Great video. Love peoples advise & comments. We are all learning, all the time.
Probably some insulation on the external tubing and perhaps making the internal coils run around the inside of the fridge instead of just staying in the middle would increase the effictiveness, but this is a great project with very little effort. Wonderful work!
If anyone is planning on trying this they can call manufacturers of the fridge for information on where wiring and tubing is in the fridge, also the inlet and outlet pipes can be insulated for better results ( I worked in both Aquarium and refrigerator industries )
Keep the updates coming on Leon, They are very interesting and your delivery is excellent.
I'm currently working on building a paludarium for some Kaiser newts, and seeing that I live in the scorching central valley in CA, I'll definitely need to get a good chiller for these cold-loving amphibians. Though I'll probably just end up buying a prefabricated chiller, the idea of building one from scratch is certainly intriguing.
I might try this project myself once I have a bit more experience under my belt; I'm not a very handy person, and I'm sure I'd find a way to screw this up somehow if I tried it now.
Read all the (well, not all of them, of course) comments. There are some very good tips to add to the functionality of this build, use a second hand fridge (cost reduction) where to site your drill holes (safety) grommet your tube holes (reduces wear and tear on the plastic) don't take out the drip tray (otherwise freezer drip water into the main area of the fridge) There's a hella bunch of knowleagable people in the comments section. Though, my thought is no Kaiser newts in central vally CA, (they are stunning, tho) I'm sure some warm loving species would be kinder (I can't imagine how I'd feel if my cooling system broke down on 'em) Be brave. DIY is really all about failure until you get it right.
Nicely done! You can also increase it's effectiveness buy insulating the clear tubes externally. The more insulation, the less strain on the compressor. I had used a long freezer (a GE I believe) and dedicated most of the right side of it for my 45 gallon tank chiller. It worked well (dropped the temp on average of 15 to 18 degrees in a fairly warm basement) and I had plenty of space left over for other frozen goods to boot, so it was a nice thing to do all around. Say hi to Baxter and Leon for me!
I built one for my 100 gal tank with a much smaller refrigerator and a dinky coil compared to yours , the only difference is my coil is submerged in a bucket of water ! The water temperature is almost a constant temp with no fluctuations when the refrigerator kicks on and off..
Thats a good idea
Yeah water would transfer heat much quicker than air.
How cold can you get a 100 gal tank?
@@marcusverhage3679
With 2 inch pink foam on the bottom of the tank in the summer heat of northern Minnesota it stays below 65 F
@@wayne-oo Not terrible. I'm shooting for at least 50 to get me through the summer. My fridge gets as low as 22 degrees F. Think I can make it work?? I'm on the fence in pulling the trigger on a chiller.
pure pleasure to watch someone work :) cheers!
I like my house temp at 65 so he’d be ok here. But I love this video, I didn’t know we could build something like this!
Hello 👋 Stephanie
How are you doing today
Heck yeah Baxter cameo! 😊💖
Awesome you noticed that Natalie! ✌️✌️✌️😻
nice job, and a Stella at the end.. true man of culture.
Leon became the luckiest Lobster in the world when you stepped into his life...or into the Seafood Mkt. Hooray for your new creation, Leon's new water cooler. Great job! (Btw Zoomies, ref. Ader Farm Great Pyrenees guard dog).
Hello Paula
How are you doing today
Great use of Dasani. No one has to drink it and it saves energy.
😅😅😅
This is fantastic you are building this for Leon
You did a great job,So smart,you are so good to Leon interesting video ,Thank you🧡🦂
At first i was wondering why this aquarium video was in my recommended - but then i realised its Leon's dad!
Hugs to Leon 🥰. 🖊️ ✂️🌡️ DIY. Multi uses 👍.
I'm probably not gonna make one of these anytime soon but I enjoyed your video and love listening to your knowledge. Also Leon at the end was cute☺💕😍
As a failsafe, I'd add a thermostat to shut down the fridge incase it gets too cold. I'm not sure how sensitive he will be to temp swings but a lot of inverts are. Overall a great job!
I stopped eating lobster long ago; now I know more about why! Thanks Leon!
Great job I really love this video thank you for sharing
Hello 👋 Michelle
How are you doing today (
This was really fun and interesting to watch. Thanks, Brady!
Definitely a fun project! Thanks for sharing!
Well done! Thanks for posting this
You can feel the joy Leon has in that last scene
Aluminum tape with insulation tape around the outlet tube could help keep temperatures down even lower, also seal the holes on the refrigerator with foam fill let’s get that thing chilling
It always nice to see your technique with chilling explanation, thank you!
This was a well thought out project that is affective and cost controlled. I suppose you could even add a filtration system into the hose to remove suspended particles from the water of needed, requiring less time vacuuming the substrate. Leon is going to one cool lobster on those hot summer days! Great job..I think you are spoiling him...LOL
It is an interesting concept and build but I'm curious to see how long the compressor lasts in the refrigerator. They aren't really designed for a constant heat source and instead for short bursts and maintaining the fridge at a specific temp.
That's why he added the water bottles in the fridge, and freezer area. They stay frozen/cold, and lower the load on the system.
@@EbolaxMonkey It's still going to kill the fridge in a few years, at least when in a warm climate. This concept is the equivalent of leaving the fridge door open all day.
If the stainless steel coil is immersed in a bucket of water , it should overcome it.
Did this for a 29 gallon axolotl tank works super effectively u can keep them at natural temps
You could get hired as a History Channel narrator, Brady. Don't be surprised if they hit you up!
If you live near or in a college town, these types of mini fridges are up on second hand sites like CRAZY this time of year! You could save yourself an extra $100 bucks by buying a second-hand fridge!
Hello 👋 joy
How are you doing today?
Great project, you are relying on the air flow within the fridge to circulate around the stainless coil, you could increase the cooling capacity by adding a low voltage fan to blow the cool air through the coil, you can buy usb powered fans from Amazon with speed control for a few dollars.
It's super calming to just watch DIY projects when done correctly, like this, other times the person is doing those '5 minute DIY' stuff that just is plain stupid considering their usually making something that's already kind of easy, to be harder
Awesome video. I'd wondered how these things worked
We need Leon!~ We need Leon!~ We need Bradys description of how Leon is doing! Please get Leon a side by side aquarium filled with other fish, so he thinks he has other aquatic things around him. Or better yet he needs a flat screen tv that projects happy life at the bottom of the Ocean.
this guy cares sooooo much about his animals