Boss Chapter 2: GT-100 Amps, Speaker Sims, Mic Choice & Placement
HTML-код
- Опубликовано: 8 сен 2024
- Hi Guys!
Thanks for dropping in again to Tone.Yard.Music, my personal Creative Portal. Currently I'm doing weekly videos on the Boss GT/GP systems and today I'm featuring the GT-100 Amplifier Section.
I'm sure you have played around here enough to know where all the drive tones are, speaker sims, mic placement etc, but here I'm going to show you how important it is to carefully choose your Amplifier, apply various settings on the unit and then return back and tweak again to really smooth out the tone you are looking for.
In this video:
1. Master Settings Required to getting started (Output / Phase Loop)
2. Recording a Loop to use while you edit
3. SECTION 1: AMPLIFIERS (Full demonstration on all amps)
4. SECTION 2: SPEAKER (Full demonstration on all speaker sims)
5. SECTION 3: EQ (Maximum Q, Boost, Scan & Cut)
6. SECTION 4: REVIEW: Going back and fine tuning your tone.
7. Demonstration of the Orange Revern Amplifier Tone I've created.
I hope this helps you really understand the unit and see the potential. If you can hear it in your head, you can create it !
Instgram ► / jaredgunston
** Support the Channel **
Subscribe Today! ► goo.gl/BaM7ng
#JaredGunstonTV #Producer #RUclipsContentCreator #Guitarist #GuitarTone #GuitarTips #Distortion #GuitarSoundForLive #GuitarSoundForRecording #StudioGuitarist #Vocalist #VocalEffects #VocalCompression #BossArmy #RolandPlayer #GX-100 #GK-3 #GR-55 #GT-1000 #GT-1000core #SY-1000 #VE-500 #Pocket-GT #VocalWireless #GuitarWireless #HereToHelp
#BossSA #RolandMusicSA
![[Jack Thammarat] BOSS GT-100 Demo](/img/1.gif)
This is one of the best demonstation video of the unit.
Also an inspiration for all the lazy people out there who want readymade presets to find their dream tone..
This is how you build a tone. Cheers!
Shivam khandelwal thanks MAN! wow what a great comment.
Mark Jones haha! fair enough dude, each to their own! :)
I have been using Boss GT-100 for about 3 years and never tweak the EQ setting like you did in this Video. Thanks for sharing this, I will try to do some EQ tweaking on all my favorite patch.
Thanks man! A Little "Engineering" trick, glad it works for you guys too!
Genuinely learned more from this video than i have from reading the manual repeatedly and reading online guides for the last 2 weeks. thanks man
Fantastic man!!
Great job man 🤘🏼 even BOSS couldn’t explain it better
Thank you for this! I didn't know how to craft my tone. I'm starting all over again. Worth it. 😁
I am glad my technique works for you :)
i was searching for this information for 3 days. you are our saviour
Very helpful! I wonder why Boss doesn't make Videos like this. They should pay you a lot! Its hard to look all these RUclips Videos till you find some like this! Good job, thank you a lot...and perhaps some more?
I used this unit for 3 years. At first for a long time I didnt have my sound dialed in because it have so many cabs, mics and settings it took me at least 15 months to learn what is what. Killer sound, and this unit is cheap. New firmware update comes with Guitar to MIDI so you can use your guitar as a midi controller. You can use the pedals as a midi controller and probably allot of things I am still not aware of. It can reamp. It have 2 outputs in USB port so you can record your effects from one input and DI input on the other. It have a very good audio interface. Plenty of signal in the volume knob. It is a small unit you that you can turn up to insane volumes with its volume knob wich is very impressing. I guarantee you it have more output then any amp can take without clipping, that is if you turn it all the way up, as it all can be adjusted. It takes time to learn as this unit can do insane ammounts of things.
Same for the 1000 gotta spend 1.5 years to master and then you still learn. I spent good time with 100 and it was my got to sound for a long time.
Salut ! Your work is perfect ! One of the best demo ever ! Congratulations ! Bravo !
Good job, dude. Realy great sound... Respect from Russia.
Some people who say they can't dial a good metal tone with gt 100, need to watch this video..then may be they will change their minds..😁..
Nice demonstration of how to tweak the parameters of gt 100
Meant to reply to this earlier. Thank you!!! They great devices, not copies of tones, you put in the effort and design your own sound.
@@JaredGunstonTV This is one of best demonstration i have watched so far.. 👍
@@rockr8840 thanks dude. Still at it!
Using a loop to help select a preamp is a great idea. Thanks.
Wow!!! Great playing mate. Love that tone man😃. Thank you for sharing that technic. It helps big time. I didn't know about the eq cut awesome stuff.
Nice set up sending support here
Que legal! Eu não sabia que dava pra editar o patch com phrase loop ligado....
👍🏽👏🏽👏🏽👏🏽
I needed that explained to me ,,, thanks for the tutorial
Thank you! I couldn't find the cab. sim. section, so this demo helped a lot.
hi there,
many thanks for this video. It is really helpful. Thumb up and greetings from Germany....
good video of the gt100 finally...guys dont even try the online patches they really suck...create your own its simple. Dont waste your time.
Очень позновательно, спасибо большое!!!
thanks for the demo
thanks man..really really helpful..appreciate it..
+Bikash Rana Most welcome! Thanks for watching !
Nice tutorial. This is what I was looking for. Cheers.
thanks man, an old one but still think it holds up today! :)
This is extremely useful. Thank you so much!
Bit of an old video but I think the logic still applies. Thanks for watching
👍
@@JaredGunstonTV Ive been using my pals gt100 but ive been thinking about getting one of my own. are there better sounding units?
@@yiftach2949 gt1 is the same brain and cheaper and smaller. The Gt1000 is my current from them and is the new flagship.
Dude, thank u so much for these vids....I am gna pick one up next week...then have a mass clear out....thanks again..
You did amazing! Great video
THANKS A LOT MAN! That was really useful! YEAH!
Awesome video, man!!! Thanks.
Diggin' these vids dude! Very helpful
+Chaz Nielsen Thanks! :D
Great demo thanks!
What are you hearing when sweeping for freqs to cut? I mean, they all sound strange when boosted but im unclear on what stands out sonically on the ones worth cutting. Thank you.
Thanks a ton man! Very good and helpful video. :)
wow !! thanks a lot man. cheers \m/
Cool, thanks 👍
This is so amazing
Well done Sir!
Thanks!
I'm too lazy, This is not in the ballpark of my pedal and amp though I wish it was conveniently so. AT 12:12, things sound a lot better though, probably with the bass in there.
Thats what most people do when they search for amp sound they like, but I found a better method. Scrolling through the presets or amps and speakers is time taking. There are many presets, many amps and speakers, so what I started doing is not choosing any of them at all. Not even amp or speaker cab. This is cosm amp, and it can do its own amp sounds and speaker cab sounds. Completely custom. Try playing with custom amp and custom cab option to quickly get a killer tone. You will find yourself making great sounds faster, and spending more time on playing them rather then searching for them and tweaking to your own needs with EQs and this type of stuff..
Fair and valid point. For me I find using this method I learn the types of amps and the possibilities of each. And in my line of work I have to know how to dial up a specific tone type etc so having that knowledge before hand helps me. Thanks for your point though I'm sure it can help some!
dude!!!! first of all REALLY THANKS!!!! that helped A LOT just one question ... do you have the pedal directly connected to a PC or though an amp? ... amazing sound didnt know about that "Q" thing filter!
Fantastic! Direct in, no amp. :)
+ToneYardMusic Wow amazing ! You just convinced me to buy it ! For a direct output, the Hi Gain sound is insane !
sounds cool
Hi hope you're doing well can you help accidentally I have somehow turned the LED lights off on the channel A and B banks can you tell me how to turn them back on if you can help it will be appreciated ......... Thanks
Amazing video!! Never used the loop to create the patch... fantastic!! I normally use the output to small cube... As I use one of them... so I can't change cabinet and mic... do you recommend changing to line even using amps? Thanks a lot!!!!
Rodolfosrb thanks!! I recommend line/phones yes. Running 1 to your amp and another to the PA. That way you can make studio quality sound out front and eq your amp to please you.
Thanks...sound very good.Can you share your GT-100 patches?
+Darkwood Darko I'm submitting for Boss Tone.Central. I'll keep you posted if I get it, then all my tones will be for download :)
Can you tell me if the Gt 100 can have as many stomp units in front of the amp or even after as you like... i.e Two EQ's , two OD or Three T screamers if I wanted that......... Great vid by the way..
Hello. Thanks for the video. When setting up a patch like this do you use headphones, studio monitors, or what? Did you ever post this patch anywhere? Do you ever change the Input Level from the default "0" setting? Thanks again.
Studio Monitors. I sometimes adjust my global noise suppression level depending on which guitar I use. :)
EQ on that thing is the weirdest thing I ever touched. It sure can do some weird tones, but it is easier to use graphic EQ. I avoid the EQ on my pedal.
merci.
svp j ai probleme avec Pra quand je modifi un patch et je met Pra (on) ce changement se fait sur tous mes autre pacth automatiquement
Im using a mesa boogie 4x12 and an evh 5150. Ive got my gt100 running through the fx loop of the amp to my liking. I got a great sounds i just wanna add like an ir or something similar to the mooer radar...is it more practical to just use the built in mic placement sim inside of the gt100? If i have a physical 4x12 cab and speakers that i love..do i use the speaker simulation as well? Or should i just use the mic sim? Also do i need to place the mic sim in my signal chain or does it just go automatically when its active
Hello! Well... in my honest opinion, if you're using it for Fx and or Amp Control, I used to do the same with a Hughes & Kettner Warp X head and 4x12 cab and I'd just turn the amp section off, play around with output settings though to get the cleanest sound for your setup, Honestly I used to leave it on RECORDING but a lot of guys moan about tone on this setting, vs the Lines or Amp Return Setting, Actually come to think of it... I got good results on the Small Combo vs Stack Return... just have a play and you'll see. If you want to add IR what would you be using it for? To change out your cab sound ? Not best to maybe look at a load box and a IR loader. ? Otherwise running 4 cable method you could achieve different tones to your cabinet if setup correctly. (I THINK!)
Short answer: You don't need the Mic Sim and or Amp slot in use is you are using your Head and Cab. Unless you wanted to add a secondary drive/Over Drive or Clean tone into your mix.
How do you make a blank starting point? Thanks
Press write and look for INITIATE.
in english lol : i record my effects loop and I read it but when I change an amp or an effect the sound remains the same. help me !!!! thanks
Hi the bro . I try to do it but did not work for me . Can you post that patch please?
Are you using the looper while making the changes? Sorry if this was previously posted somewhere.
Yes
j enregistre ma boucle d effet et je la lis mais quand je change un ampli ou un effet le son reste le meme . help me !!!! thanks
Question - is it possible to run the cab sim on GT-100 separately for left and right side, lets say I want to put the left output in my power amp without cab sim and the right output to my drummers monitoring system with cab sim? Thanks
Martin Javorek I used to ask the same thing and in all honesty it sounds the best to me set to line/phones
Great video. I love the Orange Reverb amp at 12:52 - do you have the patch or patch settings available?
+JestersTear1 Yeah that's the amp tone I like to use most of the time... Since this video I've really smoothened my tone. I'll definately be sharing. I'm also submitting to Boss Tone.Studio. Let's hope i get it!
Great news :)
Have you got on Boss Tone Central ?
I currently have boss me-25. is there a huge difference in sound quality? I dig the lcd screen and looks easier to tweak than the smaller me25. let me know. tech noob here
asdf asdasf hey! Much easier to tweak yeah. The new gt1 is the replacement for the Me25 with this sort of programming and software. personally I prefer the gt range.
hi do you have a patch close to John petrucci I have some that are close would like to know if you had a good one ...., cheers
Steven Louth send me an example.
I am wondering, if this feature is even usefull when I already play on an amp with speakers. I can go through FX return and use cab sims, but the mic pos and speaker cab sim option just confuses me to the extreme.. Should I even use this? I think its for recording via USB only, but then why the hek I can turn it on and off while I play on an amp? When choosing preset I always have to check if speaker cab sim and mic pos are on because it kinda make no sense in having these on and the difference in sound is big.
It's for recording out yes, but great for designing your tone on stage too should you not have an amp and if you do use an amp pop it in the fx return and it will help enhance your tone. If it isn't for you though and you not using the mix section I assume you using amp drive and tone and pedal as an fx centre?
My friend (grasshopper) you have answered your own question. The good man simply showed us very nicely and very clearly how to utilize the powerful and flexible GT-100 in a pure virtual world.
Enjoy your "real amp and speakers" my friend and practice your Brazilian Jujutsu rear-naked choke in the meantime.
Cheers!
my gt100 does not have the last two amp models :/ orange rv and brng uk ,what should i do to get these?
Hi! Update your software!
www.boss.info/us/products/gt-100/downloads/
Where are the other chapters?
Hi ! thx for the video ! I'd like to download your effects, is it possible ?
+Anthony Rouneau I'm submitting for Boss Tone.Central. I'll keep you posted if I get it, then all my tones will be for download :)
Quick question, I just purchased an Audio Technica M40x headphones and I tried them on the GT 100, I can only hear the right side, is there any settings that I need to mess around to make both work?
I've had similar problems that stemmed from using the wrong 1/4" Jack adapter. The size and amount of the rings on the plug varies depending on whether it's mono, stereo, has built in mic etc. You should be using a stereo Jack (3 rings- L, R and GND)
Sometimes only plugging the Jack in partially can be a quick fix but it's usually pretty unstable
Hi just wondering. if you can help me with a quandary I have just got a new amp and struggling to hook up the GT100 and the SY300
I have the GT100! set up in the send and return but not sure how to hook up the SY300 in the chain any ideas will be appreciated....... Cheers.....
Steven Louth hell8! i used to hook them up myself. guitar in to gt100, gt100 to return of amp, or input depending on what you like. gt100 fx send to sy300 input, sy300 output to gt100 fx return. use a midi cable if possible from gt100 to sy300 to control patches. now on the gt100 you can move the fx loop around, you can also choose to have it parallel or serial etc. enjoy!!
whats also fun is to have a string sound fro, sy300, and run the fx loop in parallel. and use the expression pedal of gt100 as a volume for sy300. play clean tones and fade strings in and out.
cheers thanks for that .is there a way to hook it up via the 4 cable method I have tried it 4 cable method and then input gt100 into l/mono of sy300 then guitar out of sy300 input it worked but sounded awful ....
thanks for the help
this pedalboard works better with what kind of amp??? transistors,valves ,???? peavey amps or randall for a gt100?
I'd like to know too.
I read that keyboard amps are better because they have a flat response, but a good one, like Roland, is more expensive, also they are hard to sell, if you decide to do that later. Waiting for any help! Thanks!
+Leandro Souza thanks for the info man! lets try a keyboard amp then.. :)
Hey guys! A nice valve is nice like a kettner. But usually live I'm just using a set of monitors. No acoustic foot print etc. :) I agree on the keyboard monitor, try it!
If Using a valve amp, you should go with the "4 cable method", throught the effects send/return of your amp. after that match the gt 100 output to the Best configuration regarding the type of amp you are Using. example: if you have a combo amp, you should choose tthe same type on the gt 100 's output
I bought gt100 yesterday and I read the manual.. but im still bit confused on patch structures. .. I get lost every time this is my first multi effect pedal
I'm not quite sure your confusion, feel free to add more detail and I'll try to help. Patch structures... you mean FX Chain?
JaredGunstonTV Its just that i feel lost while surfing effects...
JaredGunstonTV i can assign 4 patches on 4 pedals, right? So first I press the first pedal and choose a patch from bank up and down pedal right? and then repeat the same on rest 3 pedals? why does my expression pedal switches off every time i change a patch? only thing I understand is the EZ tone..Please reply and correct me if im wrong 😔
Haritarth Bhardwaj Did you figure it out? Cause it's much easier on a computer.
Only tip I'd give on your playing is you need a deeper vibrato. Other than that, nice.
John Smith shot. but these videos aren't about me, I try to focus on the gear in an easy understandable way. :)
I can't understand why someone makes instruction videos without talking, , explaining why, what for, adjustments, steps, moves being applied are doing, causing, what knobs control what functions, parameters. Guess I missed that in First Video? Some insight explanation would be helpful. But I will watch, probably rewatch may understand better, make notes. Receiving GT 100 today, and have to get prepared quickly. Thank You.
Hi! That was my second video so I was new to the whole RUclips thing. There's talking on my newer videos. Guess you could say the musician channels of today weren't around when I started so had no point of reference yet 😂
Not that they weren't around... Just hadn't discovered that whole world yet. Was going blind.
✌️
How do we do this in the Boss Tone Studio?
It's greyed out.
I dont know why whenever I watch gt100 videos I feel this pedalboard is not QUITE better than my poor GT10. Probably it sounds a bit better, but I feel only a bit. It seems there is not such a superiority in the GT100.
Hi. I went from the 10 to that and from that to a GR55 and a 1000. I think it's all down to preference man. I personally prefer a 100 to a 10 and a 1000 to a 100. But even last night people tell me I've never sounded better on my GR55 which is 10 amplifiers. As long as it does the job that makes you happy man!!
Distorsión de creep Radiohead please one tutorial
I no longer have the pedal bud onto the 1000 at the moment. Wish u well
So many amp models and not one sounding like i want it.
Try the 1000. 🤟
Its not Phase loop, its PHRASE loop.
OK 🤣 just don't call the Grammer police.
It's a phrase loop, not phase.
I often talk quicker then my month can get words out haha!!
Amos sound horrible
Amps