This is genius!! I've watched quite a few of these now and while they are ll great, this one uses nothing but cheap hardware store parts and a drill.. GENIUS!
Nice job! There are video's on YT that show you how to make a jig that'll make multiple size dowels with just the jig and your tablesaw. Some even include sanders to sand your dowel while it's being made.
Такая конструкция обычно первой приходит в голову. Когда я первый раз делал станок для круглых палок, делал похоже, только ножа было два. Но потом оказалось, что лучше всего работают конструкции, где медленное, с произвольной скоростью, можно даже от руки, вращается заготовка и быстро вращается режущий инструмент, стачивающий выступающие места. Например, болгарка с пильным диском или фрезер и т.д.. Потому что режущий инструмент сбалансирован, значит нет вибрации, и срезает материал любой твёрдости, значит поверхность получается точнее и более чистой. Ведь заготовки часто не имеют идеальной формы и имеют сучки и прочие изъяны.
very good idea. A little improvement : try to make an angle on longitudinal ribs to make it cut better, like a drill bit. I think you will get better surface finishing.
At the end of the day the cutter is just hot rolled mild steel and not likely to hold a cutting edge for very long before it starts to tear out wood like the two tear outs in the third dowel A wooden dowel.cutter with a single tool steel cutter set at an angle like hand pencil sharpener makes smoother dowels as does a dowel tube type cutter . Or a dowel plate
Look in extremely danger and unstable.....i like it 😏👍....great video i gonna make one...my like and subscribe Greetings from buenos aires Argentina...
If you fix two stands after the cutter to just hold the rod so that the woods turning would be restricted to turning only not playing it would have cleaner round rod would have been.
На входе поставить отверствие круглое в которое входит квадрат , на вьіходе поставить отверствие в которое входит обработаньій квадрат , так качество обработки будет вьіше и вместо ключа торцевого изготовить квадрат , тогда отпадают дополнительньіе подготовительньіе работьі и еще если фрезу изготовить с соответствуещей стали , тогда фрезу можно закалить . Удачи !
Good idea. The issue is you get what you pay for. A cheap hole saw would work for a couple of sort softwood dowels. Then be too dull and start to burn the wood…no-one has the time to sharpen it between uses. Using (otherwise scrap sized) iron pipe will it’s thicker walls will last, be able to take the wear of hardwoods and be much easier to sharpen and maintain as needed. Great video.
A hole saw should be a hardened tool steel as well - that’s a good idea. It would require a lot less sharpening than iron pipe, which doesn’t really hold an edge.
El único inconveniente es que no queda totalmente recto ya que el taladro no esta fijo y esta expuesto al movimiento del cuerpo. Ese sistema solo serviria para empotrar trozos en la pared para poder atornillar tornillo que se requieran para apoyarse alguna repisa, cables, etc.
Obviamente es un procedimiento que nos entrega la solución de una manera ingeniosa y sencilla. Si quieres perfección, no te queda otra que usar un torno, pero ¿¿¿cuánto cuesta uno??? 🤷♂
This is genius!! I've watched quite a few of these now and while they are ll great, this one uses nothing but cheap hardware store parts and a drill.. GENIUS!
Pretty smart. This would work for lots of stuff, nothing fancy, just very cool. Thank you. Jim
3
Invention of useful tools👍👍
Muito obrigado por compartilhar conosco suas experiências
Muy buen video. Uno de los mejores que he visto, respecto a transformar una madera cuadrada a redonda. 👍🏼👌🏼
Xlent innovation, mai बहुत dino se aise jugaad k talks m tha.thanks my dear.
Nice job!
There are video's on YT that show you how to make a jig that'll make multiple size dowels with just the jig and your tablesaw. Some even include sanders to sand your dowel while it's being made.
Excelente video, me encanta como se hacen los palos para las escobas. o para las cortinas muy buenas...
Спасибо за видео.
اللهم صل وسلم وبارك على سيدنا محمد وعلى اله وصحبه اجمعين
عملك ممتاز جدا واصل
Bom dia meu amigo gostei da sua ideia muito bom mesmo que legal parabéns
Simple sa lekin behtarin idea
Children, don't try this at home, especially with your fingers holding down a part being ground via grinder that one can lose control of real easy.
Please children read this! I almost lost my fingers last week because I was too confident to pay attention!!
Fricking awesome great idea
awesome workout I ever see thanks that's what the real ideàs
Very cool....i use a router bit...with a router table and fence....works good too. Well done!
With a much tidier job in the jig the results would be good! This job it's only a started idea!
Щгщрщощо
Удачи тебе мастер 👍👍👍
Отличная идея!! Брависсимо
This is the best tool for make wooden dowels
That's more than I can do. Nice job!
Anda sangat cerdas. Terima kasih tutorialnya
Brilliant idea Kaka, greetings from an Indonesian carpenter
👍🏻👏Красавчик, толково придумано, отлично сделано!
Very good idea!
Good job 👍👍👍✌🇱🇰🇱🇰🇱🇰🇱🇰🇱🇰
Спасибо! Лайк! Маладэс!
Amazing work
Amazing 🙂 loved it 👍
Excelente dica parabéns, gostei muito do gabarito
Eu pensei nisso e o rapaz do video já colocou em prática.
Super cool jig! Thanks for posting this video 😊
Excelente Muy 👍 Bueno 👏👏👏
Good instruction
Good job sir
Creative wood skills. Well made video.
Show de bola meu amigo parabéns pelo seu trabalho ganhou mais um inscrito e deixo aquele like valeu 👍🏻👍🏻👍🏻👍🏻💯🤝
Amazing and nice
So glad he finished the project with a full set of fingers
Easy but impressive! Thank you!
👍👍👍
A ferramenta é top
Start with an old bit 1” and weld a plate to it. So much easier and faster. Enjoy. Follow me for more tips.
Такая конструкция обычно первой приходит в голову. Когда я первый раз делал станок для круглых палок, делал похоже, только ножа было два. Но потом оказалось, что лучше всего работают конструкции, где медленное, с произвольной скоростью, можно даже от руки, вращается заготовка и быстро вращается режущий инструмент, стачивающий выступающие места. Например, болгарка с пильным диском или фрезер и т.д.. Потому что режущий инструмент сбалансирован, значит нет вибрации, и срезает материал любой твёрдости, значит поверхность получается точнее и более чистой. Ведь заготовки часто не имеют идеальной формы и имеют сучки и прочие изъяны.
Если ещё добавить несколько простых направляющих после прохождения проточки...,что бы заготовка не отклонялась, то получится ещё точнее и проще.
Зуб заточил не с той стороны.Поэтому и сколы на изделии.
Great innovative thinking.. love your videos
Good idea! Good luck!
감사합니다 저도 만들고싶읍니다
very good idea. A little improvement : try to make an angle on longitudinal ribs to make it cut better, like a drill bit. I think you will get better surface finishing.
Sorry for replying on your order comment on older video but will this work for 3/8th dowels?
@Digão Conteúdo Variado fala aí meu parça top msm o vídeo
At the end of the day the cutter is just hot rolled mild steel and not likely to hold a cutting edge for very long before it starts to tear out wood like the two tear outs in the third dowel
A wooden dowel.cutter with a single tool steel cutter set at an angle like hand pencil sharpener makes smoother dowels as does a dowel tube type cutter . Or a dowel plate
Very good
This is awesome
good job..bos...
Здорово!
Ide kreativ sangat bagus,,
Good job i have learnt something thanks
Kênh nào làm DIY là tôi đk hết
Way cool
Oke👍boooossssku👉👍👍👍👍👍 sip
Al u need now is a sander for the inside of the metal pole so that it will come out smooth
Omg the ease of this dowel based on pipe size wow…
SHOWWW...
PARABÉNS
It was amazing
Look in extremely danger and unstable.....i like it 😏👍....great video i gonna make one...my like and subscribe
Greetings from buenos aires Argentina...
Dowels this size and larger can be made by basic spindle turning on a lathe ,and have a smoother finish with minimal.sanding
But how many peopple have lathe machine in their workshop.
@@Micro_Trader dowels can also be made , using the Bodbers trade tools of side axe , draw knife and spoke shave , and spring pole lathe
The knife is simple and powerful, but the pre-processing of wood is a bit more complicated
Excellent
K medida se utiliza para hacer palos de 15/16, y 7 /8 . K medida es tubo galbanizado. Gracias
هذا الاختراع ممكن تعمله وتعمل منها مسامير خشبية الرجل للمكانس اليدوية،ودمتم بخير وصحة وعافية.
Looks like adding a chip breaker might help
Trust me. Any up and down movement on the drill will give you a wide variations of diameters.
Просто и понятно
Mantap👍
Zor
Hola que madera utilizó. Gracias
Pine
Pls replace the bearing of the angle grinder
If you fix two stands after the cutter to just hold the rod so that the woods turning would be restricted to turning only not playing it would have cleaner round rod would have been.
Genius.
Tanks you 👍👍👍👍🇱🇰
На входе поставить отверствие круглое в которое входит квадрат , на вьіходе поставить отверствие в которое входит обработаньій квадрат , так качество обработки будет вьіше и вместо ключа торцевого изготовить квадрат , тогда отпадают дополнительньіе подготовительньіе работьі и еще если фрезу изготовить с соответствуещей стали , тогда фрезу можно закалить . Удачи !
Wouldn't it be easier just chop off the bases of a cheap hole saw set for about £20.
You would have about 10 different sizes to use as well
Good idea.
The issue is you get what you pay for. A cheap hole saw would work for a couple of sort softwood dowels. Then be too dull and start to burn the wood…no-one has the time to sharpen it between uses.
Using (otherwise scrap sized) iron pipe will it’s thicker walls will last, be able to take the wear of hardwoods and be much easier to sharpen and maintain as needed.
Great video.
No. The wider the teeth the better.
A hole saw should be a hardened tool steel as well - that’s a good idea. It would require a lot less sharpening than iron pipe, which doesn’t really hold an edge.
@@MD-en3zm just found a 10 piece carbon steel hole saw set at tool station for £ 7. 13
This would cut wood doweling for years without sharpening
El único inconveniente es que no queda totalmente recto ya que el taladro no esta fijo y esta expuesto al movimiento del cuerpo. Ese sistema solo serviria para empotrar trozos en la pared para poder atornillar tornillo que se requieran para apoyarse alguna repisa, cables, etc.
Obviamente es un procedimiento que nos entrega la solución de una manera ingeniosa y sencilla. Si quieres perfección, no te queda otra que usar un torno, pero ¿¿¿cuánto cuesta uno??? 🤷♂
Ему нужно установить поддерживающие упоры с таким же диаметром по всей траектории движения бруска.
good.......👍👍👍
Yeah with just a couple of changes that could be way more efficient and give better results.
Идея имеет право на жизнь... Особенно для малого производства. По такому принципу можно делать под разные диаметры...
Чтоб заготовка не болталась на выходе лучше закрепить деревяные люнеты на некотором расстоянии друг от друга.
Your method is probably easier, but i just carve them by hand. It doesn’t take long.
Super gadżet
Tank yu
Good old finger vice
Como eu faço pra comprar uma maquina dessa
I like it but I want something I can turn without the prep work on the wood. What could that be? 🤔
Só funciona se soldar videa na lâmina pois do contrário a fresa esquenta e ao invés de cortar,queima e não arredonda mais.
👍🏽👍🏽👍🏽❤️❤️❤️😀😀😀
👍👍👍👏👏👏👏💕💕💕
Bhai is blue color wale pakad ko kya bolte h
Pretty fantastic work, dude! 😃
I need to make something like that as well!!!
Stay safe there with your family! 🖖😊
Buy a lathe, but seriously, keeping the electric drill in the correct plane to create a straight dowel would be beyond most people.
Шканты ,,👍
Great
A dowel needs a hole. what size bit will make a snug hole the same size as the inside of that nipple?
Mantap 👍