Nice video, especially the use of stickers! For the etching process, I tape a piece of styrofoam to the back of the piece so that it floats on the surface. Eliminates the need for the tape to suspend the metal.
Leslie Kail Villarreal No I am not on FaceBook Leslie, should I be? I have messed around making jewelry for sometime, but just now getting serious about it and have acquired many high Grade tools. I would perhaps consider taking a vacation to your area and pay for your instruction for a couple weeks crash course (trouble with mastering soldering). I think the world of you and I feel that I could learn from you. Thank you, Cory
I have been looking at doing some jewlery making, and buying one of these mills for it, though I am debating which mill to buy first. I am looking at doing something similar to this, but I am also looking at making other things like rings and chainmaille jewlery too. I plan to go only with the largest size mill to get the most out if it no matter what I am doing. However, if I get the combination mill, I have a wider variety of what I can do, I can use the D shaped wire section for making rings, other sections for making wire for chains, and the flat section for etching flat metal bracelets. The other option is to specialize and really optimize my ability to produce a specific item, for example, if I buy just the 130 mm flat roller then I have a wider area to use for etching a larger plate in one go, which I can then cut into several bracelets and then place them into a container to give them a chemical patina. This would have to be done one or two bracelets at a time on the combination roller because of the limited flat surface. The benefit of the combination roller is I can change things up based on what items I make end up being more popular amongst the people I make them for. But the drawback is that I cannot be optimized for producing those things with minimal time investment. The benefit of the flat mill is that I can do a high volume of a particular item for minimal time investment, but am much more limited in the variety of items I can make. Which would you recommend?
Leslie Villarreal... Thank you so much for simplifying this.. its been so daunting for me..probably over thinking it ya know... plus its just now getting warm enough to go outside im in Tennessee... iv had the liquids to do this for months and just couldnt find a good clear video on this to feel confident to try it..again probably over thinking it... the sticker thing is so cool who knew...they just opened up a hobby lobby 5 minutes from me this week... i should get in on the stock i guess... lol... you are great for sharing this with us.. i was just sitting here today thinking its time to learn to etch metal...Im going tomorrow and buy some of these stickers.. Cant wait to take your classes you teach.. Hopefully next time around i will get too...but im already a big fan of yours anyways... much love and best wishes to you and yours...
Hi, Leslie, Do you have to anneal the brass plate after using the brass plate several times, because the plate will become very hard after a while, or is this plate only to use for a few times? Love your video's. Greetings from The Netherlands, Anja
Thank you Leslie, you rock! This was a very informative video. I always enjoy your online classes too, tons of great info for both experienced and novice smithers. Couple of questions: How many rolls do you usually get from your brass plates (the ones you used stickers on)? I see you using card stock on one side in the mill. Can you help me understand what propose that serves, and why only on one side? I've been in studio workshops where they made us use extra pieces of metal (like you did the card stock) and on both sides. I didn't like using the metal for two reasons, wasting metal, and not as good result on pattern.
It depends on how hard you squeeze them in your Mill and how deep your etch is. Generally when i use 16g brass they last about 4 rolls on sterling silver and about 5 on fine silver. The cardstock just protects your rollers from extra scratches from the brass.
I am new to all this and really want a rolling mill. My question is which Pepe machine is the right one...90mm/110/130? And then there’s the decision of combination rollers that also “makes” wire or just straight rollers. I am a hobby jewelry maker and I love etching and love what this rolling mill does....
Hi Leslie , came across this video and thought I would give it a go ! I bought some mild Steel from my local metal smiths and it works fine but rusted afterwards . How do you prevent your plates from rusting ? I was thinking of using some of this steel in. Jewellery, as I see some people using steel. Do you know how they prevent it rusting? Thanks
Hi Leslie - Thanks for a great tutorial(!). I was wondering if you (or anyone) might have suggestions on where to find brass tubing for bracelets fairly cheaply(?). I guess it would be possible to use flat sheet, but then it means bending / soldering. Ordering metal from Rio isn't very cost-effective. Just wondering if you might have some tips. Thanks! -
Leslie, thanks for all of your great videos. I've learned so much from them. Can you tell me where you got the stickers you used to etch with? Also, my sister-in-law and I are thinking of going in together and buy a rolling mill. What do you recommend for a moderately priced one?
Acutally i did use glossy paper for this design too . i made several of these plates with different transfers.I'm not a big fan of PNP but I had some already transfered. did a ton of etching that day!
Nice video, especially the use of stickers! For the etching process, I tape a piece of styrofoam to the back of the piece so that it floats on the surface. Eliminates the need for the tape to suspend the metal.
Thank you so much, I have been scratching my head about patterns on silver. I am a beginner.
You can do it!
Great tips !!!!
Thank you,Cory
(P.S. I'm the guy who likes your videos better than Dave's).
Cory Streat LoL .. who is Dave?
Great ideas, thank you.
You are so welcome!
Hi Leslie, You are an amazing Silversmith! Keep up the great work!
You're the greatest Leslie !!!!
I learned an awful lot from your videos and wish that I were able to take classes at your studio.
Cory Streat are u on Fb?
Leslie Kail Villarreal
No I am not on FaceBook Leslie, should I be?
I have messed around making jewelry for sometime, but just now getting serious about it and have acquired many high Grade tools. I would perhaps consider taking a vacation to your area and pay for your instruction for a couple weeks crash course (trouble with mastering soldering).
I think the world of you and I feel that I could learn from you.
Thank you, Cory
Hi Leslie, very detailed vid, thanks for sharing this, love your work!
you are so helpful and generous thank you so much .
Thanks Leslie! Great info. You inspire me!
I have been looking at doing some jewlery making, and buying one of these mills for it, though I am debating which mill to buy first. I am looking at doing something similar to this, but I am also looking at making other things like rings and chainmaille jewlery too.
I plan to go only with the largest size mill to get the most out if it no matter what I am doing. However, if I get the combination mill, I have a wider variety of what I can do, I can use the D shaped wire section for making rings, other sections for making wire for chains, and the flat section for etching flat metal bracelets.
The other option is to specialize and really optimize my ability to produce a specific item, for example, if I buy just the 130 mm flat roller then I have a wider area to use for etching a larger plate in one go, which I can then cut into several bracelets and then place them into a container to give them a chemical patina. This would have to be done one or two bracelets at a time on the combination roller because of the limited flat surface.
The benefit of the combination roller is I can change things up based on what items I make end up being more popular amongst the people I make them for. But the drawback is that I cannot be optimized for producing those things with minimal time investment.
The benefit of the flat mill is that I can do a high volume of a particular item for minimal time investment, but am much more limited in the variety of items I can make.
Which would you recommend?
i
recommend you watch my Durston video
Leslie Villarreal... Thank you so much for simplifying this.. its been so daunting for me..probably over thinking it ya know... plus its just now getting warm enough to go outside im in Tennessee... iv had the liquids to do this for months and just couldnt find a good clear video on this to feel confident to try it..again probably over thinking it... the sticker thing is so cool who knew...they just opened up a hobby lobby 5 minutes from me this week... i should get in on the stock i guess... lol... you are great for sharing this with us.. i was just sitting here today thinking its time to learn to etch metal...Im going tomorrow and buy some of these stickers.. Cant wait to take your classes you teach.. Hopefully next time around i will get too...but im already a big fan of yours anyways... much love and best wishes to you and yours...
Aww you are welcome! Have fun etching!
Great tip, thanks for sharing. Dave ( p.s. I'm the guy in the Pepe product videos)
love your vids! you rock :)
Merry Christmas Leslie
Merry Christmas ! 🌹🌲🦌If you need to contact me go to my website and click on the contact link
Hi, Leslie, Do you have to anneal the brass plate after using the brass plate several times, because the plate will become very hard after a while, or is this plate only to use for a few times? Love your video's. Greetings from The Netherlands, Anja
Anja van de Ridder-van Laarhoven you want the brass plate to be hard after its etched
This is wonderful and just what I had been looking for recently, I tried to share with my son on facebook and it wouldn't. :(
use this link to share with your son just copy and past it in an email or text message : ruclips.net/video/HfWG9xVff00/видео.html
Dave is the English spokes person who does videos for PEPE TOOLS.
Cory Streat oh! Dave is extremely knowledgeable!
I noticed that you didn’t make a card stock sandwich for your silver when reducing the gauge of the sheet. So it doesn’t damage the roller?
Not if the plates are made from mild steel
@@LeslieKailVillarreal thank you!
How often can you re-use the etched textures plates?
Beautiful, thank you ;-)
Thank you Leslie, you rock! This was a very informative video. I always enjoy your online classes too, tons of great info for both experienced and novice smithers. Couple of questions: How many rolls do you usually get from your brass plates (the ones you used stickers on)? I see you using card stock on one side in the mill. Can you help me understand what propose that serves, and why only on one side? I've been in studio workshops where they made us use extra pieces of metal (like you did the card stock) and on both sides. I didn't like using the metal for two reasons, wasting metal, and not as good result on pattern.
It depends on how hard you squeeze them in your Mill and how deep your etch is. Generally when i use 16g brass they last about 4 rolls on sterling silver and about 5 on fine silver. The cardstock just protects your rollers from extra scratches from the brass.
I am new to all this and really want a rolling mill. My question is which Pepe machine is the right one...90mm/110/130? And then there’s the decision of combination rollers that also “makes” wire or just straight rollers. I am a hobby jewelry maker and I love etching and love what this rolling mill does....
Hi Leslie , came across this video and thought I would give it a go !
I bought some mild Steel from my local metal smiths and it works fine but rusted afterwards .
How do you prevent your plates from rusting ?
I was thinking of using some of this steel in. Jewellery, as I see some people using steel. Do you know how they prevent it rusting?
Thanks
Hi Leslie - Thanks for a great tutorial(!). I was wondering if you (or anyone) might have suggestions on where to find brass tubing for bracelets fairly cheaply(?). I guess it would be possible to use flat sheet, but then it means bending / soldering. Ordering metal from Rio isn't very cost-effective. Just wondering if you might have some tips. Thanks! -
Do you have a video on using toner laser printer with slick magazine paper? Love your videos!!
I teach that with my online classes
Hi Leslie. Do I have to put card stock on the top and bottom of the peace when I put it through the rolling mill.
Thank you for your videos.
Jerry
Hi Jerry, when I roll silver I only use card stock under the brass:)
Thanks
Leslie, thanks for all of your great videos. I've learned so much from them. Can you tell me where you got the stickers you used to etch with? Also, my sister-in-law and I are thinking of going in together and buy a rolling mill. What do you recommend for a moderately priced one?
Google Starform stickers
The pepe 90 mm is a great mill and very affordable get an all flat one unless you need to roll wire
try A & A jewelry supply for best prices
Great, thanks
Leslie can these plates be used in a hydraulic press?
Thanks for the video. Would cricut vinyl stickers cut on a cricut machine work?
Kris Meyers yes! I have a cameo & I use the adhesive vinyl to etch with. It works the best in my opinion!
Hi Mrs Leslie
I let you know that I am interested to buy this machine it makes textures would you like to show me the address where I can buy it ?
You can get a rolling mill from Rio Grande or Otto Frei
Hi Leslie, did you ever do the tutorial on the cricut cutting machine for the pattern? would love to see it, did I miss it? xx
Jackie Davies no I did not as there are great free tuts already on you tube look for silhouette u cutting vinyl
@@LeslieKailVillarreal thanks my dear I shall have search x
I can tell by the sound of the traffic that you are in Hermosa Beach. Am I right?
Nope!
@@LeslieKailVillarreal Close?
On the biggest brass piece with the deepest etch, did you use the laser printer method, or stickers, Leslie? I know that one wasn't the Stayz-on ink.
it was the made by using rubber stamp (same stamp i show you in the video) stamped on to pap
er then copied to PNP and heat transfered
Interesting. I thought you might have used a glossy page from a magazine over PNP. Thanks, Leslie!
Acutally i did use glossy paper for this design too . i made several of these plates with different transfers.I'm not a big fan of PNP but I had some already transfered. did a ton of etching that day!
Hum I’m thinking jewelry box
1 gallon of muriatic acid in the UK cost 165£. What? Ok they call it hydrochloric acid which is much cheaper..
try looking at a pool supply store its also called hydrochloric acid
@@LeslieKailVillarreal thanks. I will.
M