How to Fix Car Noise When Turning (CV Joint and Axle)
HTML-код
- Опубликовано: 19 янв 2015
- CV axle replacement. How to stop car noise when turning the steering wheel. How to replace CV axle in your car DIY with Scotty Kilmer. How to fix noise when turning. If your car makes noise while turning it usually means the CV joint is bad and needs to be replaced to stop the problem. DIY car repair with Scotty Kilmer, an auto mechanic for the last 47 years.
⬇️Things I used in this video:
1. Diagonal Cutting Plier: amzn.to/2nraIEF
2. Breaker Bar: amzn.to/2BEo9Ep
3. Mechanic’s Tool Set: amzn.to/2Bzmccg
4. Needle Nose Plier: amzn.to/2ic4Olq
5. Flashlight: amzn.to/2BFak8y
6. Steel Jack: amzn.to/2Asgjxo
7. Shop Towels: amzn.to/2jGDfkA
8. Jack Stand: amzn.to/2jGOwBg
9. Disposable Gloves: amzn.to/2zSRuxO
10. Common Sense
11. 4k Camera: amzn.to/2hZ4AxX
12. Mini Microphone: amzn.to/2newgV9
13. My computer for editing / uploading: amzn.to/2i2sKYz
14. Video editing software: amzn.to/2jv5Fhf
15. Thumbnail software: amzn.to/2k7tz6C
🛠Check out my Garage to see what I use every day and highly recommend:
www.amazon.com/shop/scottykilmer
❗️Check out the Scotty store:
goo.gl/RwhRGU
👉Follow me on Instagram for the latest news, funnies, and exclusive info / pics:
goo.gl/ohy2cA
Consider subscribing and press the bell 🛎 icon to be notified of all new videos.
And remember, every day (7 days a week), I upload a new video on the Scotty Kilmer Channel: / scottykilmer
Also, if you like my car help, be sure to watch my live car talk show, every Thursday afternoon at 1 CST and Saturday morning at 10 AM CST on RUclips. I answer your car questions LIVE there. Just check it out at: • Video
Scotty Kilmer is a participant in the Amazon Influencer Program.
#savagescotty 
Авто/Мото
Things I used in this video:
1. Diagonal Cutting Plier: amzn.to/2nraIEF
2. Breaker Bar: amzn.to/2BEo9Ep
3. Mechanic’s Tool Set: amzn.to/2Bzmccg
4. Needle Nose Plier: amzn.to/2ic4Olq
5. Flashlight: amzn.to/2BFak8y
6. Steel Jack: amzn.to/2Asgjxo
7. Shop Towels: amzn.to/2jGDfkA
8. Jack Stand: amzn.to/2jGOwBg
9. Disposable Gloves: amzn.to/2zSRuxO
10. Common Sense
11. 4k Camera: amzn.to/2hZ4AxX
12. Mini Microphone: amzn.to/2newgV9
13. My computer for editing / uploading: amzn.to/2i2sKYz
14. Video editing software: amzn.to/2jv5Fhf
15. Thumbnail software: amzn.to/2k7tz6C
🛠Check out my Garage to see what I use every day and highly recommend:
www.amazon.com/shop/scottykilmer
❗️Check out the Scotty store:
goo.gl/RwhRGU
👉Follow me on Instagram for the latest news, funnies, and exclusive info / pics:
goo.gl/ohy2cA
Scotty Kilmer i was wondering my chevy astro is making like grinding sound only when i turn right and i cannot find rwd cv joints for my 04 chevy astro
Scotty Kilmer hey I got one for you . what if it makes the same exact noise as that but only all the way to the left and it's a rear wheel drive truck ....
YourMetaYugioh same
Dear Mr. Kilmer, I watch your videos regularly and really love them. I am facing a peculiar problem with my car which is just 1 year old. While accelerating at low rpm, I can hear clunking sounds coming from below the engine bay on the driver side. Also when the car hits bumpy roads and there's rhythmic bumps there's clunking simultaneously. My car service people could not find the problem. I changed the motor mount, but the problem persists. what can it be? I feel like I'm driving a 10 year old car with the irritating clunks.
Scotty Kilmer my cars clutch is letting out about half way but is not slipping and.has a.brand.New master cylinder and.slave
Is it just me or does everyone feel like they could do this job after watching Scotty's videos? I sure do.
LOVE your videos, Scotty.
yup!
Just allow a LITTLE more time!
most car repairs are pretty easy if you know how to do them, and have the tools. it also helps if you actually enjoy doing it.
Just like every video. Someone did it 50 times and shows you how. I think "oh I can do that you say it only takes an hour huh?" Then 8 hours later I'm curled up in a ball in a corner wondering where my life went wrong.
Yeah, Simple, I think we've all been there. When I finish a repair or maintenance job I'm usually kind of proud of myself. Then I notice that extra part I forgot to install. It's a good day, if I can remember where it went. Otherwise it's back to Google while trying not to get too much grease on the keyboard.
I sure like your videos Scotty. They're short and to the point in 2 to 4 minutes or so. I don't need to watch someone take off nuts and bolts in a 26 minute video on how to remove a tire for example. And you're entertaining. You deserve that Emmy.
Or listen to trance music while doing it.
Or listen to them describe how their back is hurting, they had to drive to 5 stores to get the part, their income/job challenges currently, their beautiful tool kit they bought for $59 at Walmart, etc... SMH
These types of videos get about 30 seconds of my attention, then we're done... Good Catch Charlie... Good catch!
100% short, simple, and to the point. Great tricks of the trade. If my Dad only watches him... I only watch him!
"took me 15mins of wiggling, but I finally got it back in".. we've all had that problem after too many drinks.
South Main Auto Repair never had that problem.
+South Main Auto Repair I knew I'd find you here looking for tips!!
After a few drinks I probably would have just skipped the clip.
'With enough wigglin you can get the balls in'
Lmaooo IKR 😝😂😂
This man is an absolute genius, every trick I've learned basically came from watching his channel as a teen
He makes it seem like it’s as easy as taking a dvd out of a DVD player and putting a new dvd in 😂😂 this guy is good
OffendedDefender becuz its not that hard lol. Pretty much the same thing. Remove and replace.
Right set of tools, common sense and a bit of patients can go a very long way
@@ezekielpatlan2324makes me wonder why mechanics charge 100 bucks an hour
I didn't know Ozzy Osborne was so knowledgeable of cars
Hahahahaha wtf
AAAAAALL ABOOOOOOAAAAAAARD
Good one!!!!😂😂
He isn’t
I'm going to changes ...hahaha
"And tighten up the big lug nut that holds the axle in place-UNNNGGGGHHH" XD
These videos are fascinating and I can't stop watching them, even though I will readily admit that at no point in my lifetime will I ever even consider attempting any of these repairs.
I love this man... his teaching on cars been saving me a lot of trouble for paying to much for this that took me 1 hour or 2 !
Dude I love all your videos. I started watching them just for fun lol
👍🏾👊🏾✌🏾🇳🇬🇺🇸
I love your videos Scotty. The most nice and friendly guy around. And I hope you were lucky dealing with that tornado. Best teacher in town.
Thank you Scotty, you are good man. Sharing your knowledge is a wonderful gift! I didn't have a dad growing up to show or share with me the tips and advise that i have learned from you over the years!! Thank you!!! 😊
this is a crazy cool guy that knows what he is doing have helped me a lot
Love how you jump straight to the point. Simple, fast and done. Thank you
Thank you scotty for you fun and simple videos...i really enjoy them and they have giving me alot of confidence in myself and saved me alot of money. As a female and a single mom never being able afford expensive cars...your videos have made my life so much easyier...so thank you
You're the man and my favorite mechanic guy👍
Hey Scotty :) I just wanted to say thanks for all your hard work on your videos! I'm not to bright when it comes to cars but your videos make it nice and simple for me to understand what the heck I'm looking for and what I need to do. Thank you!! :)
If you like my car help, be sure to watch my live car talk show every Saturday morning at 10 AM CST on RUclips. I answer your car questions LIVE there. Just check it out at ruclips.net/video/VognjkYaMjg/видео.html&feature=c4-overview . And remember, every TUESDAY I upload a new video on the scotty kilmer channel on RUclips, ruclips.net/user/scottykilmer , so don’t miss them.
Scotty, you made this look so quick and easy, I know it’s going to take me all day just to figure out what I need to do. My mechanic won’t work on my car if it still gets me from point A to point B. That is why I’ve been driving my 04 crv with front end noise when I’m making slow sharp turns in parking lots for the last year or so. Thanks for the great information. James
This old dude is the proof that you can learn and have fun at the same time 👏👏
Scotty Kilmer you are the man. Your knowledge and know-how is most trusted. Glad to have your advice. 🇺🇸
heres a tip for those that don't have a pipe like mr scotty is using,if you have a big floor jack like mine,i think its like a 5 ton or something,you just remove the pipe off the floor jack and use it.now i used this when replacing the wheel bearing on a 1995 gmc z71 truck and those nuts are really on tight but no problem.take it easy good luck see ya and all that
Best and clearest explanations I've seen so far.
He seems like the type of man that’s actually a mad scientist and has a laboratory under his garage.
Dude knows his shit. I ain't going to do it myself because I don't have room but, I'm going to get the part to save money. thanks bro!
Great video. I did this exact job on my 02 Camry just a few months ago. That clip is annoying as all hell to get back into position. It looks deceptively easy in this video but every time you think it's seated, the opposite side pops out. My hand actually slipped on the pliers after what must have been 30-45 minutes of fighting it and it magically seated correctly just by accident.
I'm really glad I just watched this one, because I drive the same car he used in the video and it could use some new CV axles but I didn't realize it was this simple, so I've been putting it off. Will be doing that and probably new struts very soon.
Great video Scott!!
It’s a little more difficult up here in NEW England USA Due to RUST!! just did the job yesterday. You have to take off the Bearing mount (3 bolts) pull it right out mount and all THEN take off the retention ring and bottom set srew. THE Bearing Collar is rust welded to the mount. We cut the shaft back 2” from the mount, broke off the bearing grease cap then heated along the inside collet seat with a mini touch (glowing hot) rapped it out with a sledge hammer. Put the mount bracket and retention ring and set srew on the new shaft outside the vehicle then with the 3 mount bolts put it back in **side note** we used grease on Both ends of the splindles 👍
“With enough wiggling you can get the balls in” 3:16
Bolts, not balls
Side note for this video...every CV axle I've ever replaced needed a little persuasion when coming out of the transmission. Using a good pry bar, wedge the pry bar between the transmission housing and the CV housing and "pop" them out. On this car in this episode, the inner axle spindle has a C-clip that keeps it from falling out. Also if you live in an area where you get snow SOMETIMES the outer axle CV shaft will "freeze" itself in the steering knuckle. Some penetrant and an impact hammer with a point bit (sitting in the center of the axle shaft) usually does the trick. Happy wrenching everyone!
-Bandito Brothers
i appreciate this soo much scotty!! I live here Houston as well, and recently saw my brother purchase a 02 malibu as a starter car and out of nowhere it started making that noise and we thought it was because the front bumper was loose and was scrapping the tire, but now i know what it is and what i needs to do. Thanks
Scotty kilmers videos are always good to watch
Still got the humor in you. Great videos Scotty!
Great video! I have one question: should I get an alignment done after replacing both cv axles?
Will be changing mine soon, glad to watch this a few time to see the process! Thank you!
He makes it look easy. Makes it understandable. I learn more here than I have anywhere else.
Hail Scotty greetings from trinidad... Please note we don't call it pipe in trinidad.... It is called torque multiplier...... To aid in breaking out stubborn nuts!
Anybody still here
No I'm not here.
Still here. Kia
Yes
Ford festiva yea
Yes sir....my 2010 Juke died yesterday😂😂😂
Love watching your clips.
You have the absolute best car repair videos. I can't tell you how much money I saved thanks to your do it yourself vids
Make sure yall get an alignment after any suspension work. Especially the CV joints.
Most cars I've driven don't require an alignment after a CV axle change. Tie rods, ball joints, etc...yes.
He disconnected the strut to knuckle bolts which have a camber adjustment. Scotty should've at least showed to mark the relationship of the strut to knuckle so you could realign it close enough. But yes this car does need an alignment now
Agree. Mark or spray bolts before remove.
David Krapenschitz not necessarily true. I'm guessing ur definitely not a mechanic so I don't think ur qualified to give advice and fake ur knowledge on this topic.
You sir, have impeccable timing! My car just recently started making that noise under the same conditions and I was wondering what it was.
You're the best, thank you!
I’ve never seen this entrance before for Rev up your engines! Love it Scotty
The best RUclips channel been watching u for years ! 💪🏿💪🏿💪🏿💪🏿🙏🙏🙏 May god bless you
Only if my mechanic could do that in 4 mins...!
They drove the car with obviously bad cv joints, cracked winshield, yet had those shiny new green "nitro fill" valve stem caps... I bet the car smelled like weed....
To be fair, it's easier to shoplift valve caps than a windshield or hard car part. :^)
Joseph DiSalvo which is kind of what I was hinting at. Why even bother to nitro fill thar ugly ass steel wheel with pure nitrogen vs the regular old 78% kind. Though I do remember in middle school we used to take those off the teachers cars at school and play pencil break with them. Our term in the day was for the metal ones, we called them "chromy's"
South Main Auto Repair lol you know its true, I take it from the name you work in the auto repair biz too... scotty can't bash his customers, but when you work on other people's cars you tend to notice things that usually go hand in hand with other things...
no, it smelled like mold cause it was sitting outside unused for years
Scotty Kilmer got to love that too... in Florida its a given even if its a couple months.
The best instructor video by far,👍🏽
Scotty's videos are the best!
"ill answer em when this tornado passes over" 😂
Scotty do you take students, I would like to learn from you sir?
Yes pls... I would love to learn everything u no.
everytime I try to find an answer i always end up HERE. love your vids dude!
I’ve learned many great things from you Mr.Kilmer.
At 3:15 did I hear: "With enough wiggling you can get the balls in"? Hahah...what she said :)
*bolts in!
Lol
HAAAAA A SEX JOKE SO FUNNY WOWWW AHAHAHHAHAHHAHAHAHA
you forgot to put the little bolt back in for the axle !
Lloyd Dailey noticed that too
He also didn't show putting the nut back on the tie rod end but you know he put them both on.
Nice and short and to the point.type of vids we need.
Thank you for all your great videos
how is it i was charged for 4 hours of labor, when you were able ot get it done in a short video?
*editing
I think you already know the answer to that.
solution to any and all car problems: "Give it a little bit of wigglin"
And some other things in life!
Thank you Scotty for another great video.
You are the best mechanic.. You make it look so easy.. And i love all your videos.. Thank for showing that.. Iam learning a lot with your videos.... Iam a painter
how about the rear wheel drive?
+bobby z that's a good question ! I have a 99 Blazer rear wheel drive !
I have the same noise in rear wheel drive :(
some RWD vehicles have cv joints back there. If not, often worn axle bearings do that
I have found a brake pad looseness with the caliper (almost nothing, but touch it make a horrible clank noise like the explain in your video), change it solve the problem with the noise, but I'll change the bearings for sure, thanks Scotty for take time to answer me, I have seen your videos for long time.
Jesus Christ it took you only 4 mins and 3 secs to finish the job? It will take me 4 hours to do that lol
Probably video editing, but he probably still did it faster than non-mechanics
He doesn't look like a demented wizard for nothing...its magic
This dude is a legend, first place I go to when I have something new to fix.
Scotty Kilmer your the best Sr!!! I really enjoy all your videos!! From Houston Tx
holy fck I like this guy lol
There wasn't even my problem but I like how this guy gave good instructions so I still give them thumbs up.
Great job Scotty my car is having this problem right now. Love your videos. 👍🏾
You makes it looks so easy...Thank You Scotty !👍🏽
Done another of work through these videos saved me so much money
I think this is the 2nd cv video you have posted but it's great to see it done on another vehicle. Did this on my car and made a world of difference. If suggest putting a new seal on if you have the axle out since it's cheap and can get damaged when removing the old axle
You're my hero Scotty!
Ok.....this my new money saver youtuber awesome
Nice job Scotty. As always!
You Sir, have a gift for teaching. Thanks!
Thanks for the car know how Scotty, we all appreciate it :) keep the videos coming
Thank you for your great videos...Hope you have avoided Tornados and stayed safe.
Really enjoy your helpful videos , thanks Mr Kilmer
Short and to the point, thank you. Love you videos.
I love your videos. They are funny but very informative. You provide a great service for the world. I think you should have your own tv show. Thanks for your help!
Thanks for the support!
The only mechanic that makes car repairs look easy.
thanks Scott for DYI, much appreciated!
thank you scotty. your videos are my go to for car problems. i sish more mechanics we like you and help full.
Hey Scotty the lady behind the counter called the cops when I asked her if she knew what a "Wiggle" tool looked like!! LOL! Your the best!
Hey Scotty. Thanks for the video. I feel like this was based off the question that I asked you last week about my car making a noise as I turned right. As soon as I saw this I thought that lol. Another great video
Like this. Straight to it. No nonsense talk.👍
God Bless you Scotty! You have just earned another fan : )
Scotty Kilmer stays wildin. That ending 😂
Scotty your videos endings are the best!
Scotty i love you, anytime i look for a video you have it😂
ALWAYS GREAT TIPS THANKS SCOTTY!
Awesome video love the joy you bring doing what you love .👍
You’re the best Scotty
Thanks for the great video Scotty! I wish it were as easy as this spline shaft on my 95 Avalon---looks like 5-6 huge super tight bolts way the hell in there that have to be taken out then reinstalled (for each CV shaft)--what a pain....
This man is a true icon
Love your videos stay awesome! Thank you ! Not everyone has someone to learn from at home
Thanks scott for this video.Very helpful.
I love the movie clips I am glad to see them back.
Nice and easy explanation I like this guy.
Gotta love you man! ❤ Thanks for all of your videos throughout the years i learned a lot!
Im glad i found you !!!