Another great tut, Nicko! THANK YOU! Another option for drying tube and mask is using the mask fit [test] setting, rather than turning it on and off. It gives a stronger air blast for a few minutes, before switching to the cool down mode.
LMAO - I love the end! That is exactly the way I drain and dry my CPAP tube. I do less Hip Thrusting and I always turn on Kylie Minogue "Can't get you out of my mind". Well done!
My partner and I (located in regional Australia) each purchased an Airsense 11 in Oct/Nov 2021 (his was a replacement for a Phillips, while I was just starting my CPAP adventure). The local supplier had a stack of them. Literally, they were literally stacked up. In our kits we each received the unit itself, the standard (white tab) humidity tank, heated hose, a mask, and a carry case. They didn't have filters for the 11, so gave us some for the 10 with instructions to cut to fit. There was no mention of a side panel or an alternative humidity tank. Thanks to your great video, my partner went back to our local supplier to ask about the grey tab humidity tank. The newer staff member there advised that the Airsense 11 has not yet been released. 😳
Pre-order the Airsense11 AutoSet 4G - cpap.review/airsense11-aus There is very limited stock available and no doubt it will sell out like it has everywhere else. CPAP Direct also wholesale cpap equipment so If you are in the sleep apnea business and want a better deal than you're currently getting direct from the manufacturers without all the headaches and sales targets. Speak to Reza @ cpap.com.au and tell him you're mate with Uncle Nicko. They can also provide you with home sleep test equipment so you can build your own patient base. If you're starting out on your CPAP Journey, here are some Top Secret AirSense11 features to help you on your way. 1. You can add an SD card in the side. 32GB or below will do the trick and make sure it's unlocked when you insert it. The SD card can be used on sleephq.com for advanced charts and reporting. 2. The AirSense11 screen will automatically adjust the brightness depending on the ambient light in the room. If you're having a hard time reading it, increasing the room's brightness will increase the screen's brightness. You can also use your phone and place it on the sensor at the top to increase brightness. 3. There are two humidifier chambers available. One is a cheap option that must be used with distilled water, and another is more expensive and can be used with tap water. It's also dishwasher safe. 4. The AirSense11 has a secret menu that can be accessed by simultaneously holding down the Blue and Purple icons for 3-5 seconds. This will unlock a lot more features and settings. 5. Adding a Climatelineair11 heated tube system will activate the climate control feature, which is one of my favourites. You can also then pre-heat your humidifier 20 minutes before bed for instant humidification. 6. If your Tube is a little damp, turn the AirSense 11 on and then off your device will activate the humidifier cool down feature, which will run air through the tube to dry it out. Here's some of my favourite CPAP gear from 2023. 1. Magic Uploader - Automatically uploads your CPAP data to SleepHQ for therapy analysis and reporting. It uploads data in real-time! Link - www.sleephq.com/magic-uploader/ 2. AirPro Copilot - The perfect backup battery! It can run an AirSense 10 for 10 hours on 20cmH20. Takes 2.5 hours to quick charge and is ultra-light and portable. Link - ruclips.net/video/mxI2YD6yKh8/видео.html 3. ResMed AirSense11 - It's small, portable and compatible with all my toys. It has incredible data capabilities. SleepHQ Yearly Pro members receive a $200 discount - cpap.review/airsense11-pro 4. CSpring MK2 - ruclips.net/video/r8UxiMSs1_0/видео.html 5. SleepHQ O2 Ring - www.sleephq.com/product/sleephq-o2-ring/ try.sleephq.com/ is my online cpap support community & cpap reporting platform. Master your therapy and improve your sleep with our powerful cloud-based platform. Create a FREE account and download your detailed therapy report today! Features Include - 1. High-resolution 'breath-by-breath' analysis - View every apnea and every breath in full detail. 2. Sleep Journal - Track how changes to device settings influence your sleep & therapy results. 3. Custom PDF reports - Detailed therapy reports complete with journal entries. 4. Therapy Trends - Monitor changes to your apnea control over time. 5. Support - Access to the SleepHQ Community Forum 6. Education - From CPAP novice to therapy PRO. Master your device and settings with the SleepHQ Academy course 7. Blood Oxygen, Heart Rate & Movement Data - Connect a SleepHQ O2 Ring to your account to view additional data sources and take your therapy to the next level. 8. Access to exclusive, member-only discounts on the latest and greatest CPAP gear And much more! Join My Facebook Community - cpap.review/facebook My Monthly Newsletter - cpap.review/newsletter Thanks for the support Cheers Nicko
@KevOzilla, yes, I’m still using it every night and I think I’m one of the lucky ones who din’t have a lot of issues finding a mask that works for me. In my personal case, I think the machine is a lifesaver, cannot sleep without it.
I just got my new machine two days ago. Been using a 10 for many years. You mentioned the SD car having a lot of information. Can I read that on my Mac or do I need a special machine? I've been watching your videos and have learned more in two days than I've learned in 10 years about CPAP machines. Thanks a lot.
Glad you're enjoying them mate. Yeah the platform i built is called sleephq.com and it's a web based application so you can access it from any device that has a web browser (ie chrome, firefox, safari etc). Visit SleepHQ.com, sign up for a free account and you can upload and review your therapy data statistics and trends. Cheers
Another way of drying your hose is putting it in a washing machine but only on the Soin cycle. I line the drum with a couple of bath towels to prevent the heated tube from being damaged by the impeller. Depending on your washer ionly have it on l low to normal but only about 20 seconds. This is pretty crucial. I've been using my CPAP machine but I've noticed a couple of things: 1) if you use the prewarm water feature and bump the hose, you may get an error saying the climate hose prewarm. The only way I could clear the error and reinvoke the prewarm cycle was to unplug it for about 30 seconds. 2). Very handy about knowing about airplane. At my CPAP dealer they didn't give me an SD card and access my machine over the cellular network. Can I use any 32 mgb or larger SD card? Thanks and enjoy watching your videos.
Without the humidifier and with the cover installed in place of the tank, Because it's the same turbine, it will become as loud as the Airmini when you breath. (Loud at the mask level as the sound of the turbine travels through the air in the tube) The humidifier tank acts like a muffler because if the cavity/baffles it adds to the path of the air.
Hi, thank you for this useful video. At 2:10 you state that part 39101 does not require the use of distilled water. However when I read online and on the rasmed website it states that you must always use distilled water even with the chamber above. Can you point to me where it says that you don't need to use distilled water with the 39101 water chamber?
Thanks Nick. Regarding the last tip for drying out the tube, I've been using the "Mask Fit" function and leaving it on for about 5 mins to dry out the tubing. Do you think that is bad for the machine to blow hard like that for a sustained period of time?
I was recently diagnosed with sleep apnea through the VA hospital here in the US. I started therapy almost 2 weeks ago and I cannot get used to this thing. The longest I have worn my mask is just shy of 2 hours before ripping it off. On average I wear it for around 30 minutes before I take it off. I don't know how any of you can do this. Currently I get better sleep with sleep apnea than doing the therapy. Haha!
Same here the VA forced me into a horrific sleep study then gave me the machine. Any type of mask I ripped off. Only thing I can barely tolerate is the nose insert pillow ones. I found a way to have it real loose on top and behind head works best.
Try using it during the day when you’re awake and doing things like reading or watching tv, using your computer/phone, etc. get your mind/body used to having it on in a non-sleep state when you’re relaxed and comfortable. If you can only tolerate it for 30 min like that, that’s fine! Just keep working at it like that and keep trying to increase your time even minute by minute - if you get anxious or stressed, you’ve gone too far too fast. You may also need a doc to prescribe an anti-anxiety med for you for while you’re working on it. Also, if your machine has a ramp setting or an auto setting, talk to your sleep therapist about using these to start “low and slow” each time you put on your CPAP to slowly adjust your pressure depending on if you’re awake/asleep and if you’re having apneic events. The key to successful transition to CPAP therapy is patience, practice, and perseverance. You must also give yourself the grace to not adjust immediately or quickly and need help in doing so. We are all different and need different approaches to learning new things. Adjusting to having something on our face is no different. If you have not tried it yet, the ResMed face masks do have a line that have the tubing that comes off the top of the mask (on the top of your head) vs off the front of the mask (your face). To me, these are more comfortable and less constricting. I prefer the “nasal cushions” (different yet similar to nasal pillows) but I think they also have a rig for a face mask as well. If you’re having problems with proper fit (mask seal) and/or taking it off, you may find you need an additional padding or a different mask option. I would also suggest talking to your sleep therapist about trialing a new one. I hope your CPAP experience gets better!
@@jessicawarth218 I’ve tried that. I’ve been trying to use this machine for almost 2 months now. I hate it. I have an appointment with a dentist to get fitted for the dental device. Hopefully that works because this CPAP machine (mask) is horrible. I cannot stand anything strapped to my face and I’ve tried several styles. I get better sleep when not using the machine. Haha.
That climate control tube is nice not gonna lie .....I do alot of camping when it's very cold and that climate tube is amazing lol I have on multiple occasions just used it in my sleeping bag on the highest pressure setting to try and warm myself up a bit ......I do use a big eco flow powerbank incase anyone would wonder
this is very helpful thank you!! i'm trialling one of these this week and when i picked up from about sleep they didn't show me any of these things!
Месяц назад
Hi Nicko, I’m finally upgrading from a Phillips Remstar A Flex to the Resmed Airsense 11, but now realise there are actually 3 models to choose from: Autoset; CPAP; and Elite. I’ve come to a standstill. Do you recommend one over the others? Cheers
Hey Nick, Everyone seems so intent on getting all their equipment dry before use, but I just don't see the point. I know others may have a different routine, but I generally wash my stuff on a Saturday or Sunday afternoon and then use it in the evening. As soon as I use it, it's going to get wet anyway. Do you really think there's a need for all this drying?
Hi Nick I have tore down my wife's ResMed air sense 10 and was wondering if you know where to get the small cable that connects the two circuit boards (4 wire press on type)
Just stumbled upon your channel trying to reduce my sleep ap machine pressure apparently its retracting my ear drums! Anyway your channel makes me feel a little less alone. I got diagnosed with severe sleep apnea at 19 and had to buy a machine. Im fit and healthy etc but its probably genetics. Im really embarrassed I have it at such a young age and have cried a lot about it. Thanks for creating a space where i feel comfortable to share my experience ❤
Hey at least you caught it early. I thought waking up angry and grumpy as a kid was just normal. Nope, it was brain oxygen depletion my entire life. So pat yourself on the back, you just bought yourself a few more decades!
**Better tip for brightening the screen** Open literally ANY app (doesn’t matter which one) that has a white background. Simply set the iPhone (white screen down) on top of the light sensor and instantly watch the display of the AirSense 11 get super bright. (No need to use the flashlight feature of your phone, as that’s too much for what’s needed). Now you have to,hand to conduct your business with the machine. When you’re done, simply remove the iPhone from the top of the cpap. Easy.
Tried looking through videos but do you have a rec for my 1 armed, elderly mother. She had a stroke so is unable to use her left arm and struggles constantly trying to get any mask on or untangled. To complicate, the stroke also effect her memory so its harder for her to learn more complicated multi-step tasks.
Hey mate, sorry to hear about your Mom and her stroke. A few masks that come to mind are the ResMed AirFit P10 pillow mask which has no clips or buckles and just pulls on over the head and the other which is a little out of left field is the Pap Tap mask that has no headgear and is held in place via a mouth guard that you bite and mould - ruclips.net/video/tlJ0_YC9WS4/видео.html . All the full face mask designs have clips etc however an F30i is probably your best bet as the clips are magnetic and it's relatively easy to pull on over the head. Cheers mate
I am a new cpap user. You commented on another video that people were complaining that on the airsense 11 the water tank was hard to remove. I have a new air sense 11 and it is not hard to remove at all. Three times in the past month I have gotten a message that the humidifier was not working. I assume this could be because the tank is not seating securely. I am not sure what I should do.
I have a humidification chamber with a white tab for distilled water only. Can I replace it with a gray tab or does it require a different cpap model? Appreciate the videos!
Hello mate, yes you can. They look very similar and work the same way but the grey tab one is dishwasher safe and i believe it has a special film/coating on the heater plate. Cheers
Excellent information. Highly appreciated. Would it be possible to assist in getting into the Tools / Service section of the BMC REsmart GII Auto. I need to see if I can recalibrate the blower motor, but the Service section requires a pass code. Getting ERROR 75 (Blower not starting) Do you perhaps have this for the BMC REsmart GII Auto? Regards
I got the Airsence 11 few month ago. I set the humidity to Auto and the heated hose to Max 30. It is too dry. I changed it to manual and set the humidity to 6. Heavy Condensation formed in the heated tube. I lowered it to 5 and still condensation is formed. Then, I lowered it to 4. It get too dry and i cough and cannot sleep. I replaced the heated hose and still the same problem. I have the S9 and humidity set to Max 6 and heated hose Max 30 and I had NO problem with condensation. Do you have an advise to me what to do?. Thank you from Toronto, Canada.
I woke up this morning and both my machine and app’s report gave me a total use time of 10 minutes, but it said that was for tonight, not last night’s sleep. I did sleep until 11:10AM, so I’m wondering if there’s a cut off time when your machine stops logging time for last night’s sleep and starts to credit your sleep time to to the following nighr’s? Also concerned that the calendar is thrown off, and when I wake up tomorrow, it will do the same thing. Any thoughts?
I think it's pretty good to be honest. When the AirSense10 dropped in 2014 the retail price here was $2595. I thought AirSense11 would be more than that considering the limited supply so it was a welcome surprise when they dropped at $2049. There's probably less margin for retailers also which means the price will not be dumped like we saw with the AirSense10 and other devices. Don't expect to see it down near $1500 in a few months time. All the best. Nicko
Have you or are you going to run the test that shows how accurate it is? I know you did the AS10 in one of your vids and it sucked. Is this one that much better?
For me I just add water and wait. it seems to heat my water automatically. So when I go to sleep the water seems to be heated compared to just filling and using right away.
@@andycondal286 I also have an AIrsense 11 and an O2 ring, and unfortunately at this time, they do not pair. However, if you have the O2 ring on your phone, you can sync the data from the previous night to your phone, then 'share' it (Airdrop if iphone or CSV file sent to an email if Android). That file can then be uploaded to SleepHQ.
Doing an import into SleepHQ for an AS10 Redmed CPAP. I notice the Redmed labelled SD card is 4GB, how many years of saving to the SD card? I.e. Machine from 2017. Getting a Resmed AS11 this afternoon and a new mask. I have had the same mask since 2017, LoL
I have question, I watched another cpap RUclips producer discuss something called a v-com for people that have air leakage from the mouths frequently. My Dad and I both use a cpap but he has periodic mouth leakage. So I was considering getting him the V-COM But after watching your videos it occurred to me that maybe the v-com would actually give the cpap false readings or would at least deeply muddle the data recorded ... thoughts? The second concern I had after watching your videos was something my mom said about Dad's sleep... that things would be going nicely (sleep wise for my dad) but then he would stop breathing and then gasp and have an air leak from his mouth... seemed a lot like that guy you reviewed who had these periodic central apneas. My cpap is monitored by my doctor but my dad's is not 😞 I need to get him in to see my sleep doctor and get him a new machine maybe a respro airsense elite which captures a lot of data and figure out if his apnea is actually being treated. He had a sleep study done a long long time ago and his current cpap is something he bought online but I'm gonna get him to my sleep doctor, get him a new machine and get him a pulse ox ring What was the kind of machine for people with the weird sleep breathing rhythms? Thanks for your videos it's been very enlightening and scary (in a good way)!
Hey mate ! I have the Airsense 11; and I changed it to the auto woman mode . I am sleeping better; however the ramp is too long and too low; I feel like I’m struggling to breathe and I start to panic; any advice?
Just increase the ramp initial pressure to a level more comfortable If you are using Air11 in AutoCPAP (min and max pressure ranges) try to set Ramp pressure near or equal to min AutoCPAP pressure If you are using Full Face mask you need increase the pressure a little bit more to avoid that struggling feeling
Thank you for these helpful hints. I have been using this machine for some times now.This machine has many inconveniences.. especially with the humidifier.. It consumes lots of water, even if you turn the humidifier to zero.. it still consumes water. As well the humidifier is tough to open. The worst part, the tube makes noises (the heated one or not). If you use the heated one then you have to ensure that the level of heating temperature corresponds to the room temperature. These noises disturb my wife... I am still working on removing these noises and may switch back to the non humidifier option. I also do not understand why they dont supply the non distilled water humidifier at purchase time. I have all of these options but I have not found out the correct solution. As well why dont they publish all of these information in the user's manual? Bottom line, I do not like this Aisense and wishes that my Dreamstation could be replaced. I do not recommend that CPAP.
It depends of the serial number and associated region of your machine I’m from Mexico and can’t connect Air11 to MyAir app if my account was crated for Mexico region So what I do was create a new account from US region since my machine comes from that country and then AirSense app connected my device. Very tricky that stuff
Yeah, I'm wondering the same. I think it comes with it, but is removed by the DME. Mine thought I'd be a clueless nitwit and told me the machine wouldn't work without the water container, but never gave that cover to me. Sigh.
I would hardly call providing a few tips 'riding it hard' Regardless of what i recommend, there will be millions of people who will end up with the AirSense11 and as such it's just a few tips to help those who do have it.
@@CPAPReviews My folks use the Airsense 10 and when I went to the medical equipment provider to pick up my PAP device after I was diagnosed, I asked them about the Airsense 10 (I noticed one in a display case along with lots of, what I assume, were older models). They said ResMed in many cases only provides the newer Airsense 11 to the medical equipment providers, that all new PAP users have to use if going through insurance (at least in the US). You can still buy Airsense 10s on other sites, so they're clearly still making them. I guess they are just pushing the new model hard.
@asciiavatar yes that's correct. ResMed has higher margins on the AirSense11 so they make more selling it compared with the AirSense10 which is why they push it through insurance
Yah, the put in a smaller blower, but as a consequence it is louder, which is why I sleep with a fan blowing air on my head (I get hot at night), the white noise drowns out the blower sound
Hello for the USA. My Air Curve 10 took a dump recently. After that, I went into rehab for a knee problem. The people here said that I should still use something, and they gave me an Air Sence 11 to use while I am here. They set it up for apap, and I HATE IT. I was very used to bi-level, and apap doesn't work anything like bipap. I feel like it's a constant struggle to breathe, so I turned it off. That's all I have to say about it. Thank you for your channel. 👩🦳
you're full of it. Just got one yesterday and Monday I'll call to send me a postage to send the shity think back. Why I'll let you know. The #10 as soon I'll wake up turn my head and saw 3 green apples. This piece of shit I need glasses and a cup of strong coffee to see same. With the reservoir full it barely lasted 1st night. This with humidity on 1 It goes back for sure. Again you-re full of it.
Thanks man, from the US, I appreciate you helping take the drudgery out of cpap. They still aren't fun but at least a little better.
Glad to help. Thanks for the comment legend. Cheers
hey im from the us also and im on cpap how has it been for you? do you use the airsense 11 also?
Another great tut, Nicko! THANK YOU! Another option for drying tube and mask is using the mask fit [test] setting, rather than turning it on and off. It gives a stronger air blast for a few minutes, before switching to the cool down mode.
That's a great idea! You guys are teaching me some cool tricks also. That's what i love about this great community. Cheers
LMAO - I love the end! That is exactly the way I drain and dry my CPAP tube. I do less Hip Thrusting and I always turn on Kylie Minogue "Can't get you out of my mind". Well done!
My partner and I (located in regional Australia) each purchased an Airsense 11 in Oct/Nov 2021 (his was a replacement for a Phillips, while I was just starting my CPAP adventure). The local supplier had a stack of them. Literally, they were literally stacked up. In our kits we each received the unit itself, the standard (white tab) humidity tank, heated hose, a mask, and a carry case. They didn't have filters for the 11, so gave us some for the 10 with instructions to cut to fit. There was no mention of a side panel or an alternative humidity tank.
Thanks to your great video, my partner went back to our local supplier to ask about the grey tab humidity tank. The newer staff member there advised that the Airsense 11 has not yet been released.
😳
Hahaha, whoops! Pretty big fine for importing and selling medical equipment with no ARTG number. It's north of 100K.
Great video! I love my Air Sense 11 so much. Got it one and a half year ago but should have had it since long ago. Probably since a kid.
Did not know about that last one. Here I've been trying to trick it into drying the hose out using the mask fit test feature.
I'll have to try that mate! Very clever. Cheers
Pre-order the Airsense11 AutoSet 4G - cpap.review/airsense11-aus
There is very limited stock available and no doubt it will sell out like it has everywhere else.
CPAP Direct also wholesale cpap equipment so If you are in the sleep apnea business and want a better deal than you're currently getting direct from the manufacturers without all the headaches and sales targets. Speak to Reza @ cpap.com.au and tell him you're mate with Uncle Nicko. They can also provide you with home sleep test equipment so you can build your own patient base.
If you're starting out on your CPAP Journey, here are some Top Secret AirSense11 features to help you on your way.
1. You can add an SD card in the side. 32GB or below will do the trick and make sure it's unlocked when you insert it. The SD card can be used on sleephq.com for advanced charts and reporting.
2. The AirSense11 screen will automatically adjust the brightness depending on the ambient light in the room. If you're having a hard time reading it, increasing the room's brightness will increase the screen's brightness. You can also use your phone and place it on the sensor at the top to increase brightness.
3. There are two humidifier chambers available. One is a cheap option that must be used with distilled water, and another is more expensive and can be used with tap water. It's also dishwasher safe.
4. The AirSense11 has a secret menu that can be accessed by simultaneously holding down the Blue and Purple icons for 3-5 seconds. This will unlock a lot more features and settings.
5. Adding a Climatelineair11 heated tube system will activate the climate control feature, which is one of my favourites. You can also then pre-heat your humidifier 20 minutes before bed for instant humidification.
6. If your Tube is a little damp, turn the AirSense 11 on and then off your device will activate the humidifier cool down feature, which will run air through the tube to dry it out.
Here's some of my favourite CPAP gear from 2023.
1. Magic Uploader - Automatically uploads your CPAP data to SleepHQ for therapy analysis and reporting. It uploads data in real-time!
Link - www.sleephq.com/magic-uploader/
2. AirPro Copilot - The perfect backup battery! It can run an AirSense 10 for 10 hours on 20cmH20. Takes 2.5 hours to quick charge and is ultra-light and portable.
Link - ruclips.net/video/mxI2YD6yKh8/видео.html
3. ResMed AirSense11 - It's small, portable and compatible with all my toys. It has incredible data capabilities.
SleepHQ Yearly Pro members receive a $200 discount - cpap.review/airsense11-pro
4. CSpring MK2 - ruclips.net/video/r8UxiMSs1_0/видео.html
5. SleepHQ O2 Ring - www.sleephq.com/product/sleephq-o2-ring/
try.sleephq.com/ is my online cpap support community & cpap reporting platform. Master your therapy and improve your sleep with our powerful cloud-based platform.
Create a FREE account and download your detailed therapy report today!
Features Include -
1. High-resolution 'breath-by-breath' analysis - View every apnea and every breath in full detail.
2. Sleep Journal - Track how changes to device settings influence your sleep & therapy results.
3. Custom PDF reports - Detailed therapy reports complete with journal entries.
4. Therapy Trends - Monitor changes to your apnea control over time.
5. Support - Access to the SleepHQ Community Forum
6. Education - From CPAP novice to therapy PRO. Master your device and settings with the SleepHQ Academy course
7. Blood Oxygen, Heart Rate & Movement Data - Connect a SleepHQ O2 Ring to your account to view additional data sources and take your therapy to the next level.
8. Access to exclusive, member-only discounts on the latest and greatest CPAP gear
And much more!
Join My Facebook Community - cpap.review/facebook
My Monthly Newsletter - cpap.review/newsletter
Thanks for the support
Cheers
Nicko
Uncle Niko, any tutorial for SleepHQ???
@caguas56 here you go mate - ruclips.net/video/KMwDi3C3a8c/видео.html
Awesome. Found your channel recently after being diagnosed and was issued an AirSense 11. Great content.
Great to hear! Appreciate the comment. Cheers
hey how has it been? still using it every night?
@KevOzilla, yes, I’m still using it every night and I think I’m one of the lucky ones who din’t have a lot of issues finding a mask that works for me. In my personal case, I think the machine is a lifesaver, cannot sleep without it.
@perezdr1 which mask do you use?
Resmed Airfit P10
I just got my new machine two days ago. Been using a 10 for many years. You mentioned the SD car having a lot of information. Can I read that on my Mac or do I need a special machine? I've been watching your videos and have learned more in two days than I've learned in 10 years about CPAP machines. Thanks a lot.
Glad you're enjoying them mate. Yeah the platform i built is called sleephq.com and it's a web based application so you can access it from any device that has a web browser (ie chrome, firefox, safari etc). Visit SleepHQ.com, sign up for a free account and you can upload and review your therapy data statistics and trends. Cheers
Another way of drying your hose is putting it in a washing machine but only on the Soin cycle. I line the drum with a couple of bath towels to prevent the heated tube from being damaged by the impeller. Depending on your washer ionly have it on l low to normal but only about 20 seconds. This is pretty crucial.
I've been using my CPAP machine but I've noticed a couple of things: 1) if you use the prewarm water feature and bump the hose, you may get an error saying the climate hose prewarm. The only way I could clear the error and reinvoke the prewarm cycle was to unplug it for about 30 seconds. 2). Very handy about knowing about airplane. At my CPAP dealer they didn't give me an SD card and access my machine over the cellular network. Can I use any 32 mgb or larger SD card?
Thanks and enjoy watching your videos.
Without the humidifier and with the cover installed in place of the tank,
Because it's the same turbine, it will become as loud as the Airmini when you breath. (Loud at the mask level as the sound of the turbine travels through the air in the tube)
The humidifier tank acts like a muffler because if the cavity/baffles it adds to the path of the air.
Hi, thank you for this useful video. At 2:10 you state that part 39101 does not require the use of distilled water. However when I read online and on the rasmed website it states that you must always use distilled water even with the chamber above. Can you point to me where it says that you don't need to use distilled water with the 39101 water chamber?
Thanks Nick. Regarding the last tip for drying out the tube, I've been using the "Mask Fit" function and leaving it on for about 5 mins to dry out the tubing. Do you think that is bad for the machine to blow hard like that for a sustained period of time?
Love the feature on the Airsense 11 that dries the hose with gentle air. No need to buy a separate hose dryer.
I was recently diagnosed with sleep apnea through the VA hospital here in the US. I started therapy almost 2 weeks ago and I cannot get used to this thing. The longest I have worn my mask is just shy of 2 hours before ripping it off. On average I wear it for around 30 minutes before I take it off. I don't know how any of you can do this. Currently I get better sleep with sleep apnea than doing the therapy. Haha!
Same here the VA forced me into a horrific sleep study then gave me the machine. Any type of mask I ripped off. Only thing I can barely tolerate is the nose insert pillow ones. I found a way to have it real loose on top and behind head works best.
@@jsplatime to get that 50% rating as payback lol
@@RowdyCheeks hah I'm already 100% so they didn't even file for sleep apnea.
Try using it during the day when you’re awake and doing things like reading or watching tv, using your computer/phone, etc. get your mind/body used to having it on in a non-sleep state when you’re relaxed and comfortable.
If you can only tolerate it for 30 min like that, that’s fine! Just keep working at it like that and keep trying to increase your time even minute by minute - if you get anxious or stressed, you’ve gone too far too fast. You may also need a doc to prescribe an anti-anxiety med for you for while you’re working on it.
Also, if your machine has a ramp setting or an auto setting, talk to your sleep therapist about using these to start “low and slow” each time you put on your CPAP to slowly adjust your pressure depending on if you’re awake/asleep and if you’re having apneic events.
The key to successful transition to CPAP therapy is patience, practice, and perseverance. You must also give yourself the grace to not adjust immediately or quickly and need help in doing so. We are all different and need different approaches to learning new things. Adjusting to having something on our face is no different.
If you have not tried it yet, the ResMed face masks do have a line that have the tubing that comes off the top of the mask (on the top of your head) vs off the front of the mask (your face). To me, these are more comfortable and less constricting. I prefer the “nasal cushions” (different yet similar to nasal pillows) but I think they also have a rig for a face mask as well.
If you’re having problems with proper fit (mask seal) and/or taking it off, you may find you need an additional padding or a different mask option. I would also suggest talking to your sleep therapist about trialing a new one.
I hope your CPAP experience gets better!
@@jessicawarth218 I’ve tried that. I’ve been trying to use this machine for almost 2 months now. I hate it. I have an appointment with a dentist to get fitted for the dental device. Hopefully that works because this CPAP machine (mask) is horrible. I cannot stand anything strapped to my face and I’ve tried several styles. I get better sleep when not using the machine. Haha.
Thank you for the tips! Love the alternate drying option 🎉
Can you share link to the c-usb cable please. Is there one on Amazon?
That climate control tube is nice not gonna lie .....I do alot of camping when it's very cold and that climate tube is amazing lol I have on multiple occasions just used it in my sleeping bag on the highest pressure setting to try and warm myself up a bit ......I do use a big eco flow powerbank incase anyone would wonder
I'm brand new to the world of CPAPs. I was just diagnosed with sleep apnea. 😢
I think I've already found a great place for info once I get going! 🙂 👍😃
Awesome mate, welcome to the club
Loved that ending!! Brother DownUnder!!! 🤣🤣 Thanks for the video! From GG in the US!
Just got mine today, thanks for the secrets
Thank you so much. You gave me a lot of helpful info.😊
this is very helpful thank you!! i'm trialling one of these this week and when i picked up from about sleep they didn't show me any of these things!
Hi Nicko, I’m finally upgrading from a Phillips Remstar A Flex to the Resmed Airsense 11, but now realise there are actually 3 models to choose from: Autoset; CPAP; and Elite. I’ve come to a standstill. Do you recommend one over the others?
Cheers
Where did you get that part of the machine that replaces the water reservoir. My machine didn’t come with that would be great when traveling
Hey Nick, Everyone seems so intent on getting all their equipment dry before use, but I just don't see the point. I know others may have a different routine, but I generally wash my stuff on a Saturday or Sunday afternoon and then use it in the evening. As soon as I use it, it's going to get wet anyway.
Do you really think there's a need for all this drying?
Hi Nick I have tore down my wife's ResMed air sense 10 and was wondering if you know where to get the small cable that connects the two circuit boards (4 wire press on type)
Awesome. Do you have any suggestions for back up power for those using oxygen concentrator along with cpap therapy.
Just stumbled upon your channel trying to reduce my sleep ap machine pressure apparently its retracting my ear drums!
Anyway your channel makes me feel a little less alone. I got diagnosed with severe sleep apnea at 19 and had to buy a machine. Im fit and healthy etc but its probably genetics. Im really embarrassed I have it at such a young age and have cried a lot about it. Thanks for creating a space where i feel comfortable to share my experience ❤
Hey at least you caught it early. I thought waking up angry and grumpy as a kid was just normal. Nope, it was brain oxygen depletion my entire life. So pat yourself on the back, you just bought yourself a few more decades!
@@jspla thank you that's so kind of you, i appreciate your comment. Glad you have detected it too :D
How do you turn off heater plate?
Excellent. Thank You.
**Better tip for brightening the screen**
Open literally ANY app (doesn’t matter which one) that has a white background. Simply set the iPhone (white screen down) on top of the light sensor and instantly watch the display of the AirSense 11 get super bright. (No need to use the flashlight feature of your phone, as that’s too much for what’s needed). Now you have to,hand to conduct your business with the machine. When you’re done, simply remove the iPhone from the top of the cpap. Easy.
Great video. When I'm traveling can I put normal filtered water the first night in my ResMed Airsense 11 until I find a market? Thanks
Great video but my machine keeps saying air leak after 3 water tanks 3 hoses changed it's POS.
I am traveling to Mexico. Want to use the side, how do I turn off heater plate?
Is the USB-c adapter for made by Resmed?
I love the idea of having the option but I’m worried about using a aftermarket power source.
I had no idea how to remove that inner piece until now. I’m afraid to take it out coz it’s never been cleaned.. 😳
haha, i've seen some pretty filthy ones over the years
Can you explain what the difference is between the 2 water tubs? I see that one is labeled "Cleanable" which doesn't explain much.
Hey buddy, yeah the premium one is dishwasher safe
Tried looking through videos but do you have a rec for my 1 armed, elderly mother. She had a stroke so is unable to use her left arm and struggles constantly trying to get any mask on or untangled. To complicate, the stroke also effect her memory so its harder for her to learn more complicated multi-step tasks.
Hey mate, sorry to hear about your Mom and her stroke. A few masks that come to mind are the ResMed AirFit P10 pillow mask which has no clips or buckles and just pulls on over the head and the other which is a little out of left field is the Pap Tap mask that has no headgear and is held in place via a mouth guard that you bite and mould - ruclips.net/video/tlJ0_YC9WS4/видео.html . All the full face mask designs have clips etc however an F30i is probably your best bet as the clips are magnetic and it's relatively easy to pull on over the head. Cheers mate
I need to filter out cigarette smoke.....is there an activated carbon filter or some hack for this?
I am a new cpap user. You commented on another video that people were complaining that on the airsense 11 the water tank was hard to remove. I have a new air sense 11 and it is not hard to remove at all. Three times in the past month I have gotten a message that the humidifier was not working. I assume this could be because the tank is not seating securely. I am not sure what I should do.
New to this machine. How do you turn off the the heater plate?
Here's a video you might like - ruclips.net/video/9x-7xkqnqeI/видео.html
I have a humidification chamber with a white tab for distilled water only. Can I replace it with a gray tab or does it require a different cpap model? Appreciate the videos!
Hello mate, yes you can. They look very similar and work the same way but the grey tab one is dishwasher safe and i believe it has a special film/coating on the heater plate. Cheers
I have a 5year old ten about to change it, question is, upgrade to 11 or get another 10. Money not the issue. Which way to go?
Excellent information. Highly appreciated. Would it be possible to assist in getting into the Tools / Service section of the BMC REsmart GII Auto. I need to see if I can recalibrate the blower motor, but the Service section requires a pass code. Getting ERROR 75 (Blower not starting) Do you perhaps have this for the BMC REsmart GII Auto? Regards
I got the Airsence 11 few month ago. I set the humidity to Auto and the heated hose to Max 30. It is too dry. I changed it to manual and set the humidity to 6. Heavy Condensation formed in the heated tube. I lowered it to 5 and still condensation is formed. Then, I lowered it to 4. It get too dry and i cough and cannot sleep. I replaced the heated hose and still the same problem. I have the S9 and humidity set to Max 6 and heated hose Max 30 and I had NO problem with condensation. Do you have an advise to me what to do?. Thank you from Toronto, Canada.
I woke up this morning and both my machine and app’s report gave me a total use time of 10 minutes, but it said that was for tonight, not last night’s sleep. I did sleep until 11:10AM, so I’m wondering if there’s a cut off time when your machine stops logging time for last night’s sleep and starts to credit your sleep time to to the following nighr’s? Also concerned that the calendar is thrown off, and when I wake up tomorrow, it will do the same thing. Any thoughts?
Now this videos definitely informative man there's a lot of garbage out there thanks brother from the land down under!
Half of the water is left over from the night before can I add water to it or should I remove last night water and put in new water
What do you think of the price point they put this at? Its not much cheaper than the creme de la creme lowenstein 20A
I think it's pretty good to be honest. When the AirSense10 dropped in 2014 the retail price here was $2595. I thought AirSense11 would be more than that considering the limited supply so it was a welcome surprise when they dropped at $2049. There's probably less margin for retailers also which means the price will not be dumped like we saw with the AirSense10 and other devices. Don't expect to see it down near $1500 in a few months time. All the best. Nicko
Have you or are you going to run the test that shows how accurate it is? I know you did the AS10 in one of your vids and it sucked. Is this one that much better?
You kill me! 😂😂😂 (USA fan). How do you pre-heat the water chamber?
For me I just add water and wait. it seems to heat my water automatically. So when I go to sleep the water seems to be heated compared to just filling and using right away.
@katmeup7 thank you, here's how you do it - ruclips.net/user/shorts_crxMbIIA4Y?feature=share
@@CPAPReviews brilliant, thank you.
i have wellu ox ring how do you pair it with this?
@@andycondal286 I also have an AIrsense 11 and an O2 ring, and unfortunately at this time, they do not pair. However, if you have the O2 ring on your phone, you can sync the data from the previous night to your phone, then 'share' it (Airdrop if iphone or CSV file sent to an email if Android). That file can then be uploaded to SleepHQ.
Most useful!
Do the side cover come seperately? Mine didn't come with it.
It doesn't come standard mate. Have to buy it as an extra
@@CPAPReviews great to know coz you made me look for my airsense 11 box and do a double check if I missed it. 😆
Doing an import into SleepHQ for an AS10 Redmed CPAP. I notice the Redmed labelled SD card is 4GB, how many years of saving to the SD card? I.e. Machine from 2017. Getting a Resmed AS11 this afternoon and a new mask. I have had the same mask since 2017, LoL
Why would someone not use the humidifier? It’s not explained.
The sh*t you can learn here. Thanks, dude!
Any time! Have a good one Captain
I have question, I watched another cpap RUclips producer discuss something called a v-com for people that have air leakage from the mouths frequently. My Dad and I both use a cpap but he has periodic mouth leakage. So I was considering getting him the V-COM But after watching your videos it occurred to me that maybe the v-com would actually give the cpap false readings or would at least deeply muddle the data recorded ... thoughts?
The second concern I had after watching your videos was something my mom said about Dad's sleep... that things would be going nicely (sleep wise for my dad) but then he would stop breathing and then gasp and have an air leak from his mouth... seemed a lot like that guy you reviewed who had these periodic central apneas.
My cpap is monitored by my doctor but my dad's is not 😞
I need to get him in to see my sleep doctor and get him a new machine maybe a respro airsense elite which captures a lot of data and figure out if his apnea is actually being treated.
He had a sleep study done a long long time ago and his current cpap is something he bought online but I'm gonna get him to my sleep doctor, get him a new machine and get him a pulse ox ring
What was the kind of machine for people with the weird sleep breathing rhythms?
Thanks for your videos it's been very enlightening and scary (in a good way)!
Hey Nicko, quick question should i buy the autoset version or the elite one?
The autoset version
@@CPAPReviews thanks for the quick response, can you elaborate abit why?
End cap?
Hey mate ! I have the Airsense 11; and I changed it to the auto woman mode . I am sleeping better; however the ramp is too long and too low; I feel like I’m struggling to breathe and I start to panic; any advice?
Just increase the ramp initial pressure to a level more comfortable
If you are using Air11 in AutoCPAP (min and max pressure ranges) try to set Ramp pressure near or equal to min AutoCPAP pressure
If you are using Full Face mask you need increase the pressure a little bit more to avoid that struggling feeling
Thank you for these helpful hints. I have been using this machine for some times now.This machine has many inconveniences.. especially with the humidifier.. It consumes lots of water, even if you turn the humidifier to zero.. it still consumes water. As well the humidifier is tough to open. The worst part, the tube makes noises (the heated one or not). If you use the heated one then you have to ensure that the level of heating temperature corresponds to the room temperature. These noises disturb my wife... I am still working on removing these noises and may switch back to the non humidifier option. I also do not understand why they dont supply the non distilled water humidifier at purchase time. I have all of these options but I have not found out the correct solution. As well why dont they publish all of these information in the user's manual? Bottom line, I do not like this Aisense and wishes that my Dreamstation could be replaced. I do not recommend that CPAP.
Hey mate, i really appreciate your feedback and i agree with a lot of it. Cheers. Nicko
Sounds like a wife problem. BTW distilled water is like $2
Why can't i connect my Airsense 11 with MyAir app? It says my region(Aus) not supported
It depends of the serial number and associated region of your machine
I’m from Mexico and can’t connect Air11 to MyAir app if my account was crated for Mexico region
So what I do was create a new account from US region since my machine comes from that country and then AirSense app connected my device.
Very tricky that stuff
That's how I dry mine. LOL
Where do I buy the side cover?
Yeah, I'm wondering the same. I think it comes with it, but is removed by the DME. Mine thought I'd be a clueless nitwit and told me the machine wouldn't work without the water container, but never gave that cover to me. Sigh.
Yeah because side cover everyone has
App does not work
try my sleephq.com app. It's a web app so you can use it on any device with a browser. We also have a native iOS app (no android yet). Cheers
You were telling people the Airsense 11 wasn't worth it a few videos back, now you're riding it hard XD what's going on bud?
I would hardly call providing a few tips 'riding it hard' Regardless of what i recommend, there will be millions of people who will end up with the AirSense11 and as such it's just a few tips to help those who do have it.
@@CPAPReviews My folks use the Airsense 10 and when I went to the medical equipment provider to pick up my PAP device after I was diagnosed, I asked them about the Airsense 10 (I noticed one in a display case along with lots of, what I assume, were older models). They said ResMed in many cases only provides the newer Airsense 11 to the medical equipment providers, that all new PAP users have to use if going through insurance (at least in the US). You can still buy Airsense 10s on other sites, so they're clearly still making them. I guess they are just pushing the new model hard.
@asciiavatar yes that's correct. ResMed has higher margins on the AirSense11 so they make more selling it compared with the AirSense10 which is why they push it through insurance
I hate mine. My S10 was sooooooo much quieter.
Yah, the put in a smaller blower, but as a consequence it is louder, which is why I sleep with a fan blowing air on my head (I get hot at night), the white noise drowns out the blower sound
@@asciiavatar get a chili pad for you bed!!! Makes the bed nice n cool to sleep!
Hello for the USA. My Air Curve 10 took a dump recently. After that, I went into rehab for a knee problem. The people here said that I should still use something, and they gave me an Air Sence 11 to use while I am here. They set it up for apap, and I HATE IT. I was very used to bi-level, and apap doesn't work anything like bipap. I feel like it's a constant struggle to breathe, so I turned it off. That's all I have to say about it. Thank you for your channel. 👩🦳
🎉😂🎉
you're full of it. Just got one yesterday and Monday I'll call to send me a postage to send the shity think back. Why I'll let you know. The #10 as soon I'll wake up turn my head and saw 3 green apples. This piece of shit I need glasses and a cup of strong coffee to see same. With the reservoir full it barely lasted 1st night. This with humidity on 1 It goes back for sure. Again you-re full of it.