How To Replace Oil Pressure Sender 2000-2006 Chevy Tahoe
HTML-код
- Опубликовано: 18 июн 2020
- Buy Now!
New Oil Pressure Sender from 1AAuto.com 1aau.to/ib/1AOSU00015
Oil pressure is the lifeblood of any engine. The last thing you want to do is run your vehicle while oil pressure is low. Even if the oil is at the appropriate level, low pressure situations can still occur! This video shows you how to install a new oil pressure sensor on your 2000-2006 Chevy Tahoe.
• Check here for more videos on the 2000-06 Chevy Tahoe • Chevy Tahoe 2000-06 2n...
This process should be similar on the following vehicles:
2000 Chevrolet Tahoe
2001 Chevrolet Tahoe
2002 Chevrolet Tahoe
2003 Chevrolet Tahoe
2004 Chevrolet Tahoe
2005 Chevrolet Tahoe
2006 Chevrolet Tahoe
Tools you will need:
• 8mm Wrench 1aau.to/obZ/1AXAA00011
• 10mm Socket 1aau.to/oK4/1AXAA00017
• 8mm Socket 1aau.to/oK4/1AXAA00017
• Air Blow Gun
• Trim Tool Set 1aau.to/oqY/1AXXX00006
• Vacuum
• Hose Clamp Pliers 1aau.to/oa6/1AXAA00076
• Hose Pinch-Off Pliers
• Needle nose pliers 1aau.to/ohz/1AXAA00051
• Needle nose pliers 1aau.to/ohz/1AXAA00052
• Socket Driver
• Socket Extensions 1aau.to/oSb/1AXAA00015
• Torque Wrench 1aau.to/oBe/1AXAA00044
• Paper Towels 1aau.to/ohJ/1AXSS00035
• Pick 1aau.to/oj8/1AXAA00037
• Razor Blade / Gasket Scraper 1aau.to/oca/1AXAA00280
Subscribe: / @trq
Check out our playlist:
Chevy Tahoe 2000-06 2nd Generation: • Chevy Tahoe 2000-06 2n...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video. 
Авто/Мото
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
For some people it’s showing how to take apart other stuff cause they probably never work on their trucks so it’s a good vid thanks for making this videos
Real "CRAZY" taking all that apart, crazy
What is even crazier is that he didn't replace the knock sensors and harness(notorious for loosing their grounding and there is a bulletin out on replacing these) or the valley pan gasket while he was in there and no mention of it either. But the video is good to watch nevertheless. These guys are by the book and I always glean info from them. I am glad they continue.
@@2009adtommy Well I believe this video is also in conjunction with how to replace intake gaskets, I think the video was just cut
Great video! Decided it wasn't worth doing myself. If I did do it myself, I would follow this video.
Great video, could not have completed the oil pressure sensor without it!
And that is how they charge for 2 hours work on a 20 minute job😉😁
Exactly
Do it yourself then bud and diagnose it yourself
Following the steps made getting to the sensor easier for me than trying to get my hand back behind the manifold. As others say it's easy to get behind the manifold after disconnecting the fuel line and other hoses, I found it easier to just follow your steps and get the job done. Thanks!
Thanks for a great video, very helpful!
I’ve seen three videos on this job and this is by far the most complex.
But like someone said, maybe it helped someone with another job.
Screw that, next time I run out of gas I'm trading mine in on a new one.
So unnecessary to remove all of that. Disconnect the pressure side fuel line at the back of the intake then you can access it fairly easily with a wobble and 12 inch extension. Literally a 10-15 minute job.
+VOLANGLER Thanks for the tip! We'll pass this info along to our production team. 1aau.to/m/Shop-TRQ
This is unreal for such a small replacement.
Well I believe this video is also in conjunction with how to replace intake gaskets and knock sensors.I think the video was just cut to the point.
I didn’t have to take all that off but Good to know how to take it off when I need to i appreciate the video 🫶🏼
Would it be the same pressures for 2000 suburban
Is it necessary to remove the whole intake and all wiring just to replace the sensor.
My 9 year old son and I did this today. He did most of the work. Great video.
2005 GMC sierra 1500, 5.3L LM7, vin-T. does my truck have a filter screen under the oil pressure sending unit? My pressure is at 40 when cold, and drops to 20 when hot. it only climbs when accelerating. the sending unit is new. we don't know if it has a filter under it.
No filter on your truck, i believe GM didn't start until 2007.
Great job except for the leaf you blew down in the head. It’ll work it’s way through😬.
If I don’t have a screen is it okay to put a screen in there?
Dam wth aint noway all that has to be removed
Nall jack, I’m gone let the shop tackle this one here.
is it ways a three wire plug
What is that Special tool?
Keep looking there is a better way to do this. I used my USB camera to see behind the engine. It is way easier than all this.
if you are doing all of these (no need) , change the intake gasket, knock srnsors and hardware, oil sensor, and the other sensor by the oil sensor, and why not, the fuel injectors, i did all of these in my 005 tahoe . make all of these removing hastle worth it !!
+@arturovalderrama4626 Thanks for the feedback! 1aau.to/m/Shop-TRQ
Done this one a couple times. 90% of this video is not needed unless you have huge hands. This videonis from a parts retailer. I think they're just trying to sell you more parts. Great forbreference and illustration though.
Just feel around the back between the engine and firewall, use the 6-point 1-1/16" or a 27mm with a 6" extension right over top and a flex head ratchet and get'er done. Do be carefull about dropping your old sensor or cross threading, etc.
Yes everything you disconnect might makenit easier, but just focus on the fuel rail and purge valve return line right next to the back corner where you're working , not all the reat of that junk. No reason to risk damage, loss, time, fiddling with perfectly good parts, etc when none of it needs touched.
All this job ,all this work is totally unnecessary unless You are the repair shop that needs hours for their techs and mechanics so they can charge 2 1/2 hours labor without caring for customers. It takes me 15 minutes to replace this sensor. The only thing I remove from the vehicle is the engine top cover ,piece of plastic. All You need is 27 mm socket, 6" extension and the ratchet ,you are done in 15 minutes ,You do have to push your hand through ,behind or between fuel line and purge valve hose but no big deal.
Easy job.
Ya the video is 20 min. But they edit out all the cussing and swearing and time to make it look easy. Count how many times the video stops and starts again. It takes a lot longer than 20 min. I know from expirience.
Your turning a 1 hour replacement job into 5 hours dude
Dont have to do all that its a 10-15 minute job if all you're doing is changing oil sender
Small arms I assume?