When will someone do a vid on how to replace a dead air pump motor? Mine just slowed down slowly to a halt and wont work again. This series is good and goes in to this more than some. Thanks.
Alright William, videos are well done. Good bit of information. Looking bit of advice,I’m having problem with air jets, once plug hot tub on at mains, jets come on straight away and don’t go off. I even stripped control panel of top of hot tub and jets still running when I turn it on at mains. Have you came across that before or any idea what it might be ?
I got problem that after heater change my differntial current fuse keeps switching of even the one on the wire or the one in my house. Could you suggest the cause I mean it should be wiring done wrong or coil is broken?
Hi William Really helpful videos, thank you. Our filter keeps stopping. I've stripped it and the black unit is red hot. Do you think that's an issue with the propeller, which causes the motor to work too hard, or the motor itself?
Hi William, I have issue with mine, no error codes the temperature gauge works as I did a descale with easyscale ? Any ideas what issue is, when I press filter n heater buttons does click ? Help it's only had few months?
Hi Martin, found your video really helpful. Trying to work out if the heater is working properly. Have taken unit apart and element was certainly warm after running water through for a couple of minutes. Does the water coming out of the outlet feel warm or is it just marginally warmer than the water going in.?
Hi Phil, I am William, I take it from your comment that the heater is not heating up to the right temperature, this could be a number of things, the first thing I would check is the Thermostat in top water outlet section and make sure the propeller is spinning fast (check my 3rd video) if there is anything at all stopping the full water flow then the heater thermostat will stop the heat element from carrying on heating (Safety device) it sounds like the heat element is heating up then switching off, take any filter off (bottom) the inlet and test the outlet water flow (Top) is flowing at a good rate, if slow then it’s likely to be the propeller or its motor, if still the same, check the heating element voltage for voltage flow, it’s probably easiest to replace with a new one, hope this helps you
Hi, I’m getting FC error on my cleverspa, not even inflated yet, it was stored for few months and now won’t inflated, after I plugged in it comes with FC error straight away, iv the resetting thing (press and hold filtration button) but that won’t work. Any advice please?
Hi William, our clever spa air jets don’t appear to working, there is power to the tub and the heater/filter is functioning normally but the air jets don’t come on. We watched a previous video and stripped unit down and checked the non return valve which was operating as it should. We also checked the pump which appeared to moving freely But now we can’t get the tub to inflate. The light still illuminated on the air jet button but there is no sound of the fan turning etc Any advice on this one?
Hi, if the pump is running, the air should be going through the tube with the none returnable valve. If it is going through and down the pipe, check it hasn't creased at the bottom of the housing (common fault) if the pump is not running it needs to be checked, it gets electricity to it.
Hi, I have a Cleverspa Monte carlo tub which has suddenly stopped working altogether with no display at all. I've tried replacing the LCD display but still no joy. Any ideas on what this could be? I've also checked to make sure power is getting to the tub which there is. Thanks in advance.
Hi Martin, this is a difficult one, firstly it sounds like something between the voltage regulator and the motherboard isn't working, you need to check whether the system inside the pump housing as power bye check from the LCD backwards to the motherboard then if there isn't any power check from the voltage regulator to the motherboard,
I have hl error code would you suggest buying a new heating element or could it be something else ? It does pump for a while but is not warming up and the temp is saying 54 I just don’t know if it can be fixed ?
Hi Debbie, An HL error usually means there is a blockage. Preventing the water circulating around the pump & heating system. The blockage can be caused by a dirty filter, a blocked impeller or limescale build up, this will cause a higher temperature reading (in your case 54) I would first take off any filter in side the Tube (if fitted) temporary whilst testing, check there isn’t any thing blocking the impelled from rotating freely (bottom inlet) and a strong flow coming out of the (top outlet) if the water is heating after 2 minutes then getting up to the high temperature then stopped heating its likely the water Isn’t flowing faster enough and the thermostat as cut the power to the pump ( it should reset when cooled down) check out my video 2/3 which shows the heating element in detail, hope this helps
When will someone do a vid on how to replace a dead air pump motor? Mine just slowed down slowly to a halt and wont work again. This series is good and goes in to this more than some. Thanks.
Alright William, videos are well done. Good bit of information. Looking bit of advice,I’m having problem with air jets, once plug hot tub on at mains, jets come on straight away and don’t go off. I even stripped control panel of top of hot tub and jets still running when I turn it on at mains. Have you came across that before or any idea what it might be ?
Hi my spa turns on displays temperature but none of the functions work light up . Where should I start to try and fix it
I got problem that after heater change my differntial current fuse keeps switching of even the one on the wire or the one in my house. Could you suggest the cause I mean it should be wiring done wrong or coil is broken?
Hi William
Really helpful videos, thank you.
Our filter keeps stopping. I've stripped it and the black unit is red hot. Do you think that's an issue with the propeller, which causes the motor to work too hard, or the motor itself?
Hi William have you any idea why my hot tub leaks when the water reaches the heater filter
Hi William, I have issue with mine, no error codes the temperature gauge works as I did a descale with easyscale ? Any ideas what issue is, when I press filter n heater buttons does click ? Help it's only had few months?
Hi Martin, found your video really helpful. Trying to work out if the heater is working properly. Have taken unit apart and element was certainly warm after running water through for a couple of minutes. Does the water coming out of the outlet feel warm or is it just marginally warmer than the water going in.?
Hi Phil, I am William, I take it from your comment that the heater is not heating up to the right temperature, this could be a number of things, the first thing I would check is the Thermostat in top water outlet section and make sure the propeller is spinning fast (check my 3rd video) if there is anything at all stopping the
full water flow then the heater thermostat will stop the heat element from carrying on heating (Safety device) it sounds like the heat element is heating up then switching off, take any filter off (bottom) the inlet and test the outlet water flow (Top) is flowing at a good rate, if slow then it’s likely to be the propeller or its motor, if still the same, check the heating element voltage for voltage flow, it’s probably easiest to replace with a new one, hope this helps you
Hi, I’m getting FC error on my cleverspa, not even inflated yet, it was stored for few months and now won’t inflated, after I plugged in it comes with FC error straight away, iv the resetting thing (press and hold filtration button) but that won’t work. Any advice please?
Turn it off..change the filter or just unscrew it..wait abit like 2 mins..turn it back on..should be OK.
Hi William, our clever spa air jets don’t appear to working, there is power to the tub and the heater/filter is functioning normally but the air jets don’t come on.
We watched a previous video and stripped unit down and checked the non return valve which was operating as it should. We also checked the pump which appeared to moving freely But now we can’t get the tub to inflate. The light still illuminated on the air jet button but there is no sound of the fan turning etc
Any advice on this one?
Hi, if the pump is running, the air should be going through the tube with the none returnable valve. If it is going through and down the pipe, check it hasn't creased at the bottom of the housing (common fault) if the pump is not running it needs to be checked, it gets electricity to it.
Hi, I have a Cleverspa Monte carlo tub which has suddenly stopped working altogether with no display at all. I've tried replacing the LCD display but still no joy. Any ideas on what this could be? I've also checked to make sure power is getting to the tub which there is. Thanks in advance.
Hi Martin, this is a difficult one, firstly it sounds like something between the voltage regulator and the motherboard isn't working, you need to check whether the system inside the pump housing as power bye check from the LCD backwards to the motherboard then if there isn't any power check from the voltage regulator to the motherboard,
@@williameccleston3845 Thanks, I will have to get the whole unit out and do some checks then.
I have hl error code would you suggest buying a new heating element or could it be something else ? It does pump for a while but is not warming up and the temp is saying 54 I just don’t know if it can be fixed ?
Hi Debbie, An HL error usually means there is a blockage. Preventing the water circulating around the pump & heating system. The blockage can be caused by a dirty filter, a blocked impeller or limescale build up, this will cause a higher temperature reading (in your case 54) I would first take off any filter in side the Tube (if fitted) temporary whilst testing, check there isn’t any thing blocking the impelled from rotating freely (bottom inlet) and a strong flow coming out of the (top outlet) if the water is heating after 2 minutes then getting up to the high temperature then stopped heating its likely the water Isn’t flowing faster enough and the thermostat as cut the power to the pump ( it should reset when cooled down) check out my video 2/3 which shows the heating element in detail, hope this helps