I am so glad I found this video! I've been going through h3ll trying to figure out what the ef is going on. I could not pin point the "goose" sound at all. So, just like in your video, went outside ran the car for a bit, it started making that "goose" sound. Opened the gas cap, put a piece of paper on it, and sure enough there it was. Making the EXACT noise from the video. You may have saved me some money! I'm going to go to the mechanic and see if he can check those two things. I'll keep you posted!
@@jasminecortinas0610 The entire kit with the connectors. Costed about 109$ at Ford. It makes a big difference even in the accelerator response. The mileage is around 32.4 mpg after nearly 4000 miles.
This sound was driving me nuts. Thank you for this video. what does this kind of repair run on a 2014 Fusion. Apparently many people with Fords have this problem why hasn't it been recalled
Great vid, I wish I'd have found this back when I had this issue. I replaced the purge valve and it completely resolved the issue. Thanks for putting this clear and precise explanation out there!
This is the most helpful car diagnostic and solution video EVER! Thank you so much! I haven't tried either yet, I'm very certain this is the issue with my car. The dealership wanted to charge me $145 just to diagnose the problem and who knows how much to fix.
@@psautomotive5530 I have a 2013 Ford Taurus. The purge valve was replaced by me because of OBD 2 code P1450. I used a new purge valve and everything is fine until the car warms up and I get a fast ticking sound from the purge valve. No rough idle, no vacuum from gas tank, no stalling.. Just annoying ticking sound. I'm hoping it's not the canister as you said. Or the lines..or even an electrical problem. What would you suggest?
This is what I'm going through right now! Sometimes it is hard to put fuel in the car I have to put it on a real low flow and hold the fuel nozzle and now that farting noise
Great video. I'm having this issue now (2013 Lincoln MKZ). My mechanic changed the purge valve assembly about a year ago. But now it's happening again. I'm wondering if it's the square canister part you mentioned
Me too. They replaced the canister MD the solenoid and still happening.he replaced fuel valve solenoid last year and FORD dealer replaced it 2 yrs ago. Seems a defective part ...how long are the solenoids supposed to last?
Thanks for this video - my 2016 Fusion Titanium (2.0L EcoBoost) started making this sound yesterday, actually died on me pulling into the parking lot of my kid's daycare! Started right up though, and a day later, the check engine light pops up - P1450. Just bought the purge valve from RockAuto for 45.00. Thanks again for the video!
The pulse valve (the one in the engine compartment) is a $130 part! It is impossible to remove and replace the whole setup without a lift and removing the lower engine cover and the alternator. On my wife's car, I cut the hoses and simply swapped the solenoid and the two one-way valves. I reconnected the tubing using two pieces of heat shrink tubing.
I'm having this problem now on my 2016 Fusion with a 2.5 L. It's been making a strange noise in the back of my vast, but the noise only happens about 2 times a month and then it never makes the noise again. I traced the noise to the driver side back of the car and now finding out that it's coming from inside my fuel tank makes sense. My husband just changed out the purge valve. It's been dying when I get gas since I got it last year. So it's great to see this video and see where the canister is located so we can buy the part and change it out.
Paisano, el vapor canister cual es el ID o SKU de esa refaccion ? Tengo un ford fusion 2013 SE ecoboost con ese fallo, consumo mucha gasolina y tengo problemas al cargar gasolina porque bota la pistola. Gracias de antemano y saludos desde Tijuana Baja California
Really great video but I’m a little stuck. I’m dealing with a 2015 fusion ecoboost that just came up with the p1450 code. It is running sluggish and has a very hard time getting to even 60 mph. It starts just fine but does not sound or run right
14 Fusion: I have the same issue, my car dosent want to start after getting gas. Also while driving I randomly here whining from the back of my car, if I stop at a light, the car try’s to idle but then it cuts off. Has anyone experienced that?
So far I have had no problems with starting etc but I did have check engine once and today it made that noise twice without any other issue. It was cyclical like 5 "buzzes" in the row very weird. Never heard that in any other car
Mee too. Had this problem in my 2013 Lincoln MKZ. My mechanic changed that vapor canister purge valve assembly. It's doing the same thing again a year later. In the shop right now 🤦🏾♂️
@@gsht5839 how much did it cost!! Mine is doing the same thing! And everytime I put gas in it stops or won’t start and I’ll have to wait a minute and then it starts but knocks for a minute
My car has this sound comes out of the fuel cap rpm vibrates along side the sound, and when I want to turn off my car it won't turn off and keeps running even when I take off the key. I'm assuming the issue is the same with the car in the video
There's also a Carbon Canister and a Solenoid that could be part of the problem. I just changed the rear Solenoid PART# CP806 Helped but started up again after a few weeks. The reason folks begin having this issue is from Overfilling theor gas tank!!! Stop topping off your tank, when the nozzle clicks, STOP. You're flooding the carbon canister.
Having the same issue, my car will die out. I have to put my push the cap less valve open and let the air equalize before it will start up, I stuck a paper clip in for temp solution
hey i have a ford fusion 2014 with problems when i turn it on it does not turn on fast and most of the times turns down by itself where im assuming gasoline is not flowing well it seems like its clogged what do you think i should do ? i think what you did is very similar to my situation thanks
Ford needs to issue a recall for this problem and just go back to putting a regular gas cap on like most cars do. It would solve a lot of problems and I have been a Ford user for more than 40 years but I hate the capless fuel tank
I have the same issue in a 2019 fusion titanium Already checked the purge valve and I was told there is no problem in it. Also I don’t have any problem starting the car after fueling nor it dies in the traffic So I changed the canister/vent valve .. it was not an easy replacement because of AWD but I really hope it will solve the issue
Same I have a 2019 fusion I already changed the purge valve with all those hoses that go connected to the engine and 2 weeks later I got my check engine light back on for same code about the evap high pressure. So I’m guessing it’s the canister near the gas tank area..
I have a 2017 fusion 2.0 echoboost and every time i fill up when i start the car it idles rough. high and low high and low for 5 minutes before it smooths out. This is exactly whats happening to me it sounds like...hmmmmmm
Yep. My Lincoln is in the shop right now for this. I spent $450 a year ago on the same issue. Changed the purge valve assembly. Now it's happening again. If u don't address it your car may start to cut off in you.
Mi fusión tiene ese mismos problema, cuando lleno el tanque de gasolina tengo que dar 3 o 4 veces para que encienda. Solo lo hace cuando pongo gasolina.
This is for a 2016 Ford Fusion, don't know if it's different per year. Purge Valve Assembly - Online I've seen as low as $60 USD. In stores about $100 USD Vapor canister vent solenoid - Online $54 USD. In stores it was $36 USD. These are only pricing for parts. Each repair shop the cost will vary.
This is the noise my 2018 Ford escape is making in my engine light is on. Every time I fill up the car it takes a car at least 5 minutes to start again.
I replaced the solenoid in the rear. The noise stopped for about 2 weeks. Can back louder. I am now replacing the hoses in the front. Having trouble getting my hands down there. I tried to use a screw drive to release the clip on the hoses noting shooting out for help.
Would it be a problem if i left this issue fir a while!? Im from overseas and my local dealer told me they have to order the part from US which will take about 6 weeks to arrive. Should i keep driving with this issue or stop until i replace the part?
Hey lev.. I got that code. Did you replace the whole assembly? I just replaced the Purge Valve by cutting the hose in half and adding it. The Purge Valve was only $23 my car was fine restarting after full tank but still the code so prob just need to replace who assembly eh?
How is it going. Well I’ve already change the purge valve and the charcoal canister it was fine for like a month but now it’s making that noise again and it smells like acetone
Since the fuel tank is design for vacuum or (negative pressure) it not dangerous. The problem is that the fuel system won’t work properly and can cause vehicle start problems.
@@psautomotive5530 I'm driving a chevrolet Cruze 2016 1.4 T LS and there's too much air coming from the petrol tank but the car starts per. What could be the problem
I guess accurate diagnostic is a solving to the problem. Carrying out the repair is a separate matter I think. In other words, if you fix either or both the parts that will solve the same problem you experience in your car. All the best.
This beats all I have ever seen a ford car that farts and a 1000 dollars worth of work to go with it, If my Mustang ever do this I will be done with ford cars for ever. A farting car $&@$&&&$-:;;;
I agree that it’s absurd. Not to mention that to replace the purge valve you gotta take all those hoses off instead of a single quick connect into the valve. But this is barely a $200 job at most. If you do it yourself which all you need is videos like this and a simple jack with jack stands or even just wood blocks you will save $300+ in labor.
I am having this same problem now. I believe Ford should be fixing these problem because it seems like a lot of people with Ford having this issue.
Yes it's is a safety issue of your car dies while driving
I agree. I have a 2015 Ford Fusion and I’ve already had to replace it twice in two years and it’s starting to act up again.
I got this right now yo! Crazy
I got it now
I bought a 2016 back in 2018. Replaced in 2020, and it failed again after two years
I am so glad I found this video! I've been going through h3ll trying to figure out what the ef is going on. I could not pin point the "goose" sound at all. So, just like in your video, went outside ran the car for a bit, it started making that "goose" sound. Opened the gas cap, put a piece of paper on it, and sure enough there it was. Making the EXACT noise from the video.
You may have saved me some money! I'm going to go to the mechanic and see if he can check those two things. I'll keep you posted!
What was the problem?
What did they do? Did it work?
Thanks for keeping us posted.
Thanks. I replaced it and it works beautifully. My gas mileage went from 28 mpg to 31 mpg after replacing it. That noise freaked me out.
Which one did you replace? my car is doing it and it’s making my nervous
@@Xo.ErisKain I have the same question?
@@Xo.ErisKain which one did you get??
Which one did you
Replace?!!!!!!
@@jasminecortinas0610 The entire kit with the connectors. Costed about 109$ at Ford. It makes a big difference even in the accelerator response. The mileage is around 32.4 mpg after nearly 4000 miles.
The video was much helpful but my question is. Can you test out the three items separately to which one is actually bad?
This sound was driving me nuts. Thank you for this video. what does this kind of repair run on a 2014 Fusion. Apparently many people with Fords have this problem why hasn't it been recalled
Exactly because I have that problem right now
Me too this is heartbreaking
Great vid, I wish I'd have found this back when I had this issue. I replaced the purge valve and it completely resolved the issue. Thanks for putting this clear and precise explanation out there!
Thanks
So do the sticky note help the problem ?
How much
this is the best explanation. this guy is a great teacher. thank you
This is the most helpful car diagnostic and solution video EVER! Thank you so much! I haven't tried either yet, I'm very certain this is the issue with my car. The dealership wanted to charge me $145 just to diagnose the problem and who knows how much to fix.
Hi Samantha thanks for your comment. Let me know if you solved the problem
@@psautomotive5530 I have a 2013 Ford Taurus. The purge valve was replaced by me because of OBD 2 code P1450. I used a new purge valve and everything is fine until the car warms up and I get a fast ticking sound from the purge valve. No rough idle, no vacuum from gas tank, no stalling.. Just annoying ticking sound. I'm hoping it's not the canister as you said. Or the lines..or even an electrical problem. What would you suggest?
Usually the purge valve makes that ticking noise as long as the check engine light doesn’t come back I think you’re going to be fine
This video helped me solve the problem. I got the ourge valve swapped out and it's work great.
This is what I'm going through right now! Sometimes it is hard to put fuel in the car I have to put it on a real low flow and hold the fuel nozzle and now that farting noise
Yep. Cost about $450 when I had that problem a year ago. Changed that purge valve assembly. No problems for a while, now it's back to farting
Did you get it fixed.
Great video. I'm having this issue now (2013 Lincoln MKZ). My mechanic changed the purge valve assembly about a year ago. But now it's happening again. I'm wondering if it's the square canister part you mentioned
same car same problem
They replaced my purge valve about 15 months ago and now the problem is back - - -
Me too. They replaced the canister MD the solenoid and still happening.he replaced fuel valve solenoid last year and FORD dealer replaced it 2 yrs ago.
Seems a defective part
...how long are the solenoids supposed to last?
HOW MUCH ?? ?
I have a 13 MKZ and mine started this too
Thanks for this video - my 2016 Fusion Titanium (2.0L EcoBoost) started making this sound yesterday, actually died on me pulling into the parking lot of my kid's daycare! Started right up though, and a day later, the check engine light pops up - P1450. Just bought the purge valve from RockAuto for 45.00. Thanks again for the video!
Did the purge velve solve the probem?
Did the purge valve solve your problem?
I would get embarrassed it always happens in the morning as im arriving to work. I just see people turning to see why my car farted lol
It happens
@@psautomotive5530 is cover under 100k miles warranty?
Exactly how I felt. Lincoln MKZ 🤦🏾♂️
Yes. I thought guy behind me was blasting his subs. 😂😂
I finally got it fixed it was a simple fix
The pulse valve (the one in the engine compartment) is a $130 part! It is impossible to remove and replace the whole setup without a lift and removing the lower engine cover and the alternator. On my wife's car, I cut the hoses and simply swapped the solenoid and the two one-way valves. I reconnected the tubing using two pieces of heat shrink tubing.
It's a 45.00 part on RockAuto for my 2016 with the 2.0L ecoBoost.
Lol you hacked your wife's car up buddy 🤣
You can do it without a lift, it’s way easier with picks
3/8" ID fuel line and 2 hose clamps works too instead of the heat shrink tubing.
I'm having this problem now on my 2016 Fusion with a 2.5 L. It's been making a strange noise in the back of my vast, but the noise only happens about 2 times a month and then it never makes the noise again. I traced the noise to the driver side back of the car and now finding out that it's coming from inside my fuel tank makes sense. My husband just changed out the purge valve. It's been dying when I get gas since I got it last year. So it's great to see this video and see where the canister is located so we can buy the part and change it out.
Paisano, el vapor canister cual es el ID o SKU de esa refaccion ? Tengo un ford fusion 2013 SE ecoboost con ese fallo, consumo mucha gasolina y tengo problemas al cargar gasolina porque bota la pistola. Gracias de antemano y saludos desde Tijuana Baja California
Really great video but I’m a little stuck. I’m dealing with a 2015 fusion ecoboost that just came up with the p1450 code. It is running sluggish and has a very hard time getting to even 60 mph. It starts just fine but does not sound or run right
Replace the Evap purge valve. Take the foam cover off and it's on the drivers side under the intake pipe
Thanks I have that exact issue on my 2013 Escape 2.0. Hard starting after filling and car farting.
14 Fusion:
I have the same issue, my car dosent want to start after getting gas. Also while driving I randomly here whining from the back of my car, if I stop at a light, the car try’s to idle but then it cuts off. Has anyone experienced that?
Yes experience currently with my 2014
Yes that exact same situation
You are THE MAN. Thank you!
So far I have had no problems with starting etc but I did have check engine once and today it made that noise twice without any other issue. It was cyclical like 5 "buzzes" in the row very weird. Never heard that in any other car
ohhhh that explains alot, I just messed with those lines trying to get the air filter changed
This was so great. Thank you for making this video!
finally know why this issue persists. thanks
No problem
Question, will this part work with the ford edge 2016 titanium 2.0 turbo 4 cyl??
Thank you so much. I freaked out when my car started making that sound
Which one was it that cause it the valve or the solenoid?
Yea which one was it
I have a 16 Ford Fusion (awd), and have had the exact same issue
Mee too. Had this problem in my 2013 Lincoln MKZ. My mechanic changed that vapor canister purge valve assembly. It's doing the same thing again a year later. In the shop right now 🤦🏾♂️
@@gsht5839 how much did it cost!! Mine is doing the same thing! And everytime I put gas in it stops or won’t start and I’ll have to wait a minute and then it starts but knocks for a minute
What electrical issues might it be. If not 3 items listed.
Mechanic is thinking starter.?? It seems wrong.
Very informative video thank you
Great explanation, thank you for this video!
Estimated cost for replacement?
Do these problems with either one of these parts cause a car to shut off as if it runs out of gas?
I replaced the purge valve and vapor canister but the problem is still there. The link in the description for the electrical problem is not working.
Thank you for this video! Now I know how to handle a very naughty Lincoln!
Thank you so much for this information 🙏
Please post a working link to the electrical video. Thanks!!!!!
Do you remember where you purchased the part
if my car vapor locks can i bleed vapor from this?
So do the sticky note help the problem ?
Is it safe to drive the car to the mechanic when this happens? I pulled over bc I got worried
thanks. great video
Thanks
Also sometimes we have found the gas tank flap open like I left it open but I know I didn't.
Anyone know how much the repair cost is for a mechanic to do it?
Is there a way to diagnose which part needs replacing prior to actually replacing them?
I wish. We just threw 300 parts a d labor. Two of the 3 done still no good.
My car has this sound comes out of the fuel cap rpm vibrates along side the sound, and when I want to turn off my car it won't turn off and keeps running even when I take off the key. I'm assuming the issue is the same with the car in the video
whats the part number for the second option?
There's also a Carbon Canister and a Solenoid that could be part of the problem.
I just changed the rear Solenoid PART# CP806
Helped but started up again after a few weeks.
The reason folks begin having this issue is from Overfilling theor gas tank!!! Stop topping off your tank, when the nozzle clicks, STOP.
You're flooding the carbon canister.
I clicked on the link and there was no video for the electrical.
Having the same issue, my car will die out. I have to put my push the cap less valve open and let the air equalize before it will start up, I stuck a paper clip in for temp solution
Thank you
Your welcome. Remember to hit the suscribe button so we can keep on making this videos, thank you
hey i have a ford fusion 2014 with problems when i turn it on it does not turn on fast and most of the times turns down by itself where im assuming gasoline is not flowing well it seems like its clogged what do you think i should do ? i think what you did is very similar to my situation thanks
Calle The barber Sounds like the Master Air Flow sensor
Could be the gas pump not holding pressure
I mean the check valve in the fuel pump
And I've also noticed a bit of lag and acceleration as well. But no doubt, that is the fart noise I'm hearing.
It will cause the car to ride a bit rough
Ford needs to issue a recall for this problem and just go back to putting a regular gas cap on like most cars do. It would solve a lot of problems and I have been a Ford user for more than 40 years but I hate the capless fuel tank
Tienes la versión en español?
Good stuff....thnaks
I have the same issue in a 2019 fusion titanium
Already checked the purge valve and I was told there is no problem in it. Also I don’t have any problem starting the car after fueling nor it dies in the traffic
So I changed the canister/vent valve .. it was not an easy replacement because of AWD but I really hope it will solve the issue
Same I have a 2019 fusion I already changed the purge valve with all those hoses that go connected to the engine and 2 weeks later I got my check engine light back on for same code about the evap high pressure. So I’m guessing it’s the canister near the gas tank area..
Where are you located?
I have a 2017 fusion 2.0 echoboost and every time i fill up when i start the car it idles rough. high and low high and low for 5 minutes before it smooths out. This is exactly whats happening to me it sounds like...hmmmmmm
Yep. My Lincoln is in the shop right now for this. I spent $450 a year ago on the same issue. Changed the purge valve assembly. Now it's happening again. If u don't address it your car may start to cut off in you.
hi!! i got the noise but not the code...any way to diagnose wich part is failure?
Which one did you end up getting that worked, I'm having the same issue
Mi fusión tiene ese mismos problema, cuando lleno el tanque de gasolina tengo que dar 3 o 4 veces para que encienda. Solo lo hace cuando pongo gasolina.
Es muy comun
First time it made sound like a BAD wiperblade?
I replaced the vapor canister and the vent valve and it’s still not starting after I fill the tank
What about the fuel purge value solenoid?
Is it fixed.
Did you fix it.
My husband says fix and trade.
After all this I'm wondering if we fox just keep...
Does anyone know the actual part number for this?
How much does a repair like this estimate around?
This is for a 2016 Ford Fusion, don't know if it's different per year.
Purge Valve Assembly - Online I've seen as low as $60 USD. In stores about $100 USD
Vapor canister vent solenoid - Online $54 USD. In stores it was $36 USD.
These are only pricing for parts. Each repair shop the cost will vary.
Cost me $450 in New Orleans
The labor is the expensive portion
Yep
How much do you think the purge valve may cost if we go and buy it ourselves?
$100 on amazon
Google
In the meantime I put a string in gas flap to stop noise
Did the string stop it from making that fart noise
This is the noise my 2018 Ford escape is making in my engine light is on. Every time I fill up the car it takes a car at least 5 minutes to start again.
This is crazy I just started having this problem I have a 2018 ugh
This problem just started in my ford Fusion Hybrid 2 days ago!!! 😡
i replace that exact part and the check engine light wont come off saying it has p1450 and p144c
I replaced the solenoid in the rear. The noise stopped for about 2 weeks. Can back louder. I am now replacing the hoses in the front. Having trouble getting my hands down there. I tried to use a screw drive to release the clip on the hoses noting shooting out for help.
There’s another video here on RUclips that helped me getting to that bottom connector. Have patience. GL
Would it be a problem if i left this issue fir a while!? Im from overseas and my local dealer told me they have to order the part from US which will take about 6 weeks to arrive.
Should i keep driving with this issue or stop until i replace the part?
I got error code P144C, found that it is related to canister purge. But how do I know which one must be replaced, vent valve or purge valve? thanks!
Is hard to say, you have to see the live data through the scanner to pinpoint exactly what is going on
Hey lev.. I got that code. Did you replace the whole assembly? I just replaced the Purge Valve by cutting the hose in half and adding it. The Purge Valve was only $23 my car was fine restarting after full tank but still the code so prob just need to replace who assembly eh?
Update !!! Fuel pressure valve was defective so we put canister but then realized the new valve was bad 😊so finally fixed. It.
Where is the link ?
What link are you looking for?
How is it going. Well I’ve already change the purge valve and the charcoal canister it was fine for like a month but now it’s making that noise again and it smells like acetone
@@psautomotive5530that was stated at the end of the tutorial video. Part 2????
0:34 - hey now.. time for some gas relief 😅
Is this dangerous?
Since the fuel tank is design for vacuum or (negative pressure) it not dangerous. The problem is that the fuel system won’t work properly and can cause vehicle start problems.
Thank you
@@psautomotive5530 I'm driving a chevrolet Cruze 2016 1.4 T LS and there's too much air coming from the petrol tank but the car starts per. What could be the problem
Well when it stalls out and your rearend yes!
Yes.. severe flatulence can lead to toxic fumes.. not good for ones health or the environment. VERY dangerous!!
this isn't really solved though. you just gave the problem light. solved is fixing the problem. thanks anyway...
I guess accurate diagnostic is a solving to the problem. Carrying out the repair is a separate matter I think.
In other words, if you fix either or both the parts that will solve the same problem you experience in your car.
All the best.
How much dose this typically cost my job is my car dependent i need it lol 😂
I just chnahed my purge valve canister and never heard it again
Minesounds a golf ball bouncing around inside
This beats all I have ever seen a ford car that farts and a 1000 dollars worth of work to go with it, If my Mustang ever do this I will be done with ford cars for ever. A farting car $&@$&&&$-:;;;
Lol I was in a drive though when my car started doing this. So embarrassing.
I agree that it’s absurd. Not to mention that to replace the purge valve you gotta take all those hoses off instead of a single quick connect into the valve. But this is barely a $200 job at most. If you do it yourself which all you need is videos like this and a simple jack with jack stands or even just wood blocks you will save $300+ in labor.
Pretty funny except the not running part
Farting car 😂
The most ridiculously designed part in the car.
The sould is like a giant fart. It only happens when the car is low on gas and it's a hot day.
Thank God my car didn't make these noises 😩😂😂😂
without being techinical. it is basically farting! Unlike Einstein, theoretically makes sense but practically you didnt prove it
Yes he showed it was sucking in air not out of tank.
Pmsl