Out of the Ordinary and Rarely Known Idea
HTML-код
- Опубликовано: 22 июл 2024
- Rarely Known soldering ideas and tricks
segment
00:00 - Opening
00:04 - How to Remove SMD Leds Using Cable Lugs
01:21 - How to Solder a Battery With a Nickel Strip
02:46 - Soldering holder from Bolts
03:55 - solder tin receptacle from syringe
05:52 - How to desolder using copper fiber
06:52 - Plastic/pvc cutter from solder
08:47 - receptacle to clean the soldering iron from an old lamp
09:45 - Soldering tin pots
11:33 - Styrofoam cutter from solder
12:41 - Closing
Visit the Creatividea Channel
See other videos here:
/ @creatividea
Don't forget to LIKE, SUBSCRIBE, and provide suggestions and comments
Thank you - Хобби
Baru kepikiran..ini mantap dan keren idenya
kereeeen pake bangeeeeet🥺👍🏻👍🏻👍🏻👍🏻
Wonderful, my friend
Wáo..! That Good and number one for you ❤❤❤
mantab bos idenya
pcb holder nya ide bagus
kerren bos serba simpel I like you
Great idea 👍👍👍👍👍😃😃😃
Good idea 👍👍👍
Super ideas
11:07. Its very good idea...bro.
But unfortunately, wasting on tin roll happened here..👌
very gopd👍
Отличная идея с отверстием в шине для аккумулятора! Да и все идеи хороши! 👍👍👍🤝
Kreatif dan inspiratif. Sukses selalu dan salam youtuber 👍👍👍🙏🙏
makasih sukses selalu
Ojalá dieras más detalles de lo que usa. Gracias
Boa seleção de músicas
guzel fikir elerinize saglık
يعطيك الف عافية بس سؤال ماهي المادة المستخدمة قبل لحام القصدير على بطاريات الليثيم وشكرا
Sir aap kaun se company ka iron bit use kartey hai. Please tell
elinize sağlık
Ý tưởng hay, rất bổ ích. Cám ơn tác giả!
Браво, добра идея. Ще я пробвам някой ден..
Thanks happy new year
🥳🥳🥳
Good
👍👍👍👍
👍👍👍👍👍👍👍
9:10 do not clean soldier tip with abrasive. It will remove the external layer and will deteriorate quickly
аккумуляторы нужно паять мощным паяльником 60-80 ватт и короткое время, одним касанием.
Bonjour c'est quoi le produit dans la bouteille ?
красавчик))
ok
نوع الكاوية ايه واجيبها من فين
Bro in this video bettery solder what r you use? Thats super glue?
This stainless flux
@@creatividea what is stainless Flux? We are just knowing about the ordinary soldering Flux? Is it something special and where we can buy it?
Tricks for those who are banned at Aliexpress. Most of necessary tools available there are more effective. I have serious doubts about trick to remove LED's from aluminum plate - the cabe tip is quite thin, can it heat the plate to melt the solder??? Ali offers PTC resistors to remove LED's.
bonjour quel et le nom du produit pour soudé a létain,pour soudé les batterie
Caraca Mano, você é demais! Vou ver se faço aqui em casa, já que tenho o jogo básico do básicos de solda.
а если еще и добавить паяльной пасты в шприц с припоем !!!
С алюминиевой подложки да запаянные безсвицовкой ну да, или плату подогрел заранее. Тогда и пинцетом можно снять.
@@yakdmitriСильно перегретое жало, наверное? Или заранее всё подмазано пастой с висмутом?
@@user-ht3dd3mb9y Такой тонкий наконечник не передаст достаточно тепла, даже если он перегрет. Ведь у этой платы алюминиевая подложка.
@@yakdmitriОбычно да, но если в помещении за тридцать, греет галогеновая лампа подсветки места работ, а на паяльной станции выставлено под пятьсот, то... главное снятый вовремя стряхнуть, если он ещё нужен...
First view bro and first like or first comment
thanks 🙏🙏🙏
@@creatividea welcome 🙂🙂
Not a very good idea as it is consuming good amount of time to damage the LED before it gets desoldered
1 is bullshit, an old idea never done like this (only copper wire that has a much higher thermal conductivity), also perfectly obsolete as now you can easily buy a hot air gun with an external pump. 2 is bullshit, as you get a heated battery full of flux. Only welding. Also cute how you test the contacts by pulling them apart, normally you need a resistance check ;) 3 is bullshit because normally you don't have that much edge area on your boards. No idea why can't you just hold it by that alligator clamp you've got, especially as this is only needed for hot air soldering. 4 has no use, as for the boards you can just carry the solder on the iron's tip (and for the thick wires it is much faster to just cut some solder and hold it by hand). 5 is a waste of time that seemingly works for the single-sided PCBs (though essentially you've just done the old trick of heating all the pins at once, it will not work for a larger part as the pins will stick to the edges and damage the copper plating). Hold the board by hand, heat the pins adding some solder for the thermal conductivity, shake the part out, heat the solder and just slightly hit the board against something for one to fall off, much faster and no wick involved :P Also totally useless, as your single-sided PCB will open the holes if some flux is added anyway. 6 is just a fire alarm trigger, get a sharp blade or Dremel for the thicker stuff ffs. 7 - like we here used to say, if a cat has nothing to do, one licks one's balls. Put this thing into a much smaller can, which takes tons less both time and space ;) 8 is not worth it, just get a larger tip and tin them normally. 9 is a styrofoam mess-up-er, as the wire has to be straight and stiff (normally fixed at both ends).
Минусовые конечно же припаивать не нужно.
Колхоз…😅
Plumbers Flux lol