This is so amazingly well explained. It gives a short simple overview of what a BMS is and how it works without compromising on any vital information. Very well done
Question. I have a 4s 12p pack with a BMS. Here is my question. If I connect the leads to each row (4) they monater each row but what each call on each row. There no way they are checked,Right. Thank you
Thank you. One question please, when the BMS terminates charge or discharge states, in a cell, do the other cells, combined, continue functioning at a lower capacity? Or does the system just shut down as a result of that 1 bad cell? I'm sorta new at this. Thanks again.
Hi, I have a left over 48 volts BMS and charger from an E-bike. And I wanna use the 58 Volt charger to charge a 24 Volt 18650 battery pack. Can I use half of the BMS to charge the smaller Battery pack???
Hey there, my skateboard BMS is clearly the issue because it is not safe or reliable. Idk whether its the BMS or a bad battery cell. But if you could please help. I'd be grateful.
My 17s battery pack is not charging above 69v I have series 13s and 4s bms There is a bit of unbalance in the cells about ± 0.05 volts Also the bms cuts the power at only at 61 volts about 3.56 per cell Please 🙏 tell me the reason so I can repair it (About two times the positive and negative terminal also get short fow a few second with bms installed)
I want to charge 12V lithium phosphate battery with a charger or power supply especially fast charge with 100Amps that can take energy from Mains supply. How to select my power supply ?
So if i were to replace a battery woth a max charge Voltage of 8.8v with one that has a max charge voltage of 8.4 the BMS would basiclly think the battery is older and not overchage it?
Sir I have a question I have li ion battery pack with making it basic bms which is comes from chine In this battery pack I tested on aging machine it is goes upper voltage 39 volt to sharp 54 volt when I charging my battery pack having nominal voltage is 36v/10ah what is the reasion behind it
Hi Erik, when the battery pack is not on a load (not connecting to any appliance or device) or even charging, will the BMS be still working automatically to balance the cells ? the cells will discharge themselves over time, not sure if the BMS still detect the pack and start balancing according to the cell parameter. Thanks !
this was a well presented explanation and i greatly appreciate it. i do have a question. can the leads of the BMS be connected to the plus or minus on the batteries. the info i have it should be the plus side. however overkill BMS is using some plus and some minus connection. do u have some inside? thanks for ur time
Thank you for your video. Great explanation for how a bms works. I am wanting to learn how to test a battery pack that won't take a charge. Is it a bad battery or a bad bms? Can the bms be bypassed to see if the batteries in the pack will charge directly?
I'm very new to ebikes. If you have 10 seconds I have a quick question sir; if someone was running 2 hub motors and their combined max current from the controllers was 60 amps, and you used a battery with 50amp BMS (52v 20ah), what would happen? If you ran WOT you may trip the BMS of the battery and it come back on after a few seconds? Or something worse? Thank you!
I am an engineering student from India. i am looking for a proper BMS and also the most reliable battery that my team NIRMAAN HYPERLOOP can use in our boring machine and the hyperloop pod, if you could help us with your knowledge on thus, it would be great. thank you
Howdy S-S, ... any RECOMMENDATIONS for a 48 Volt BMS brand Name ? I run a 36 PV panel system, in a 6S / 6P configuration 230 volt "DC" input ALL-IN-ONE 120 / 240 volt "AC" GROWATT Inverter SPF 6000T DVM-MPV I would like to BUILD my own Battery Bank ... Thanks, COOP the WiSeNhEiMeR from Richmond, INDIANA ...
you mean to say monitoring the cell or battery if its charging the wire for cell b1 b2 b3 just monitoring only not charging the charging come from negative and positive and the other 3 wire b1b2 b3 just monitoring the voltage when charging
justin trudeau is clearly a man of many talents.
Yes, but this look alike sells bMs, rather than plain BS.
I was about to say that 😅😂😂😂
😂😂😂
haha
Ur geniune comedian😂
This is so amazingly well explained. It gives a short simple overview of what a BMS is and how it works without compromising on any vital information. Very well done
Dear Mr. Eric,
Thanks for presentation, your video is very simple and effective about BMS.
Totally agree
What a great way to explain to a beginner. The concept is very clear with this presentation and will help understanding the next levels. Thank you Sir
Thanks for the clear explanation, it turned out very helpful for my thesis!
Dear eriik,
Thanks for the simple and clear explanation, well done 👍
Very simple to introduce the BMS. Great presentation !!
Easy to understand presentation. Well done Erik.
Simple and well explained, thanks a lot!
Question. I have a 4s 12p pack with a BMS. Here is my question. If I connect the leads to each row (4) they monater each row but what each call on each row. There no way they are checked,Right. Thank you
very clear explanation video ! Thanks a lot!
Simple explanation but powerful. 🙏
this is the best explanation on bms....
I will make a playlist if you don't have one!!!! This is so great!!!
Excellent video. Thank you.
Thanks for the clear explanation, your work appreciated
Very good lesson for BMS knowledge
Very Nice Explanation. Lots of information. Please do more videos
Can I connect the battery directly to the hover board, bypassing the BMS?
Finally someone else who explains this
Thank you. One question please, when the BMS terminates charge or discharge states, in a cell, do the other cells, combined, continue functioning at a lower capacity? Or does the system just shut down as a result of that 1 bad cell? I'm sorta new at this. Thanks again.
Hi, I have a left over 48 volts BMS and charger from an E-bike.
And I wanna use the 58 Volt charger to charge a 24 Volt 18650 battery pack.
Can I use half of the BMS to charge the smaller Battery pack???
Great presentation. Very articulate clean.
Thanks for doing a great job of explaining what the BMS in a battery pack does.
Hey there, my skateboard BMS is clearly the issue because it is not safe or reliable. Idk whether its the BMS or a bad battery cell. But if you could please help. I'd be grateful.
Hi
Can u tell me how to decide what should be balancing current according to the capacity of the cells?
Do we have a full circle recycling system?
Hello, How to solve cell unbalance? Is there any relevant introduction in this regard?
My 17s battery pack is not charging above 69v
I have series 13s and 4s bms
There is a bit of unbalance in the cells about ± 0.05 volts
Also the bms cuts the power at only at 61 volts about 3.56 per cell
Please 🙏 tell me the reason so I can repair it
(About two times the positive and negative terminal also get short fow a few second with bms installed)
Excellently explained
I want to charge 12V lithium phosphate battery with a charger or power supply especially fast charge with 100Amps that can take energy from Mains supply.
How to select my power supply ?
what's the song?!
So if i were to replace a battery woth a max charge Voltage of 8.8v with one that has a max charge voltage of 8.4 the BMS would basiclly think the battery is older and not overchage it?
Great , thanks for this , clear classes
Sir, charger why not on without bms??
How to on for testing without bms??
So what Smart phone app can access this information? How is connected?
why is the gnd of the slave of the two integrates connected by the daisy chain connected to the last cell of the master
Sir I have a question I have li ion battery pack with making it basic bms which is comes from chine
In this battery pack I tested on aging machine it is goes upper voltage 39 volt to sharp 54 volt when I charging my battery pack having nominal voltage is 36v/10ah what is the reasion behind it
Hi Erik, when the battery pack is not on a load (not connecting to any appliance or device) or even charging, will the BMS be still working automatically to balance the cells ? the cells will discharge themselves over time, not sure if the BMS still detect the pack and start balancing according to the cell parameter. Thanks !
I'm rebuilding a 15s2p battery pack, can I replace the original 30 amp bms with a 60 amp bms? Thank yu
Thank you! Very Helpful
Is there a BMS 16S in your plan for LifePo cells for HV battery design?
Very good presentation, thank you sir.
Great presentation ,
does the BMS limit what the battery pack's max pulse draw is or is it separate?
What is a comms. Interface?
Wt is galvanometer resistance in BMS
Good explanation. How does one bypass a BMS and charge a low cell via current controlled power supply at say 20% of the Ah rating rated current.
Which language used for this project , pls tell me
What does charge and discharge mean in a bms?
How can we get it
Best explanation!
Why are the outputs based on algorithmic averages as you have stated, and not actual readings?
Great video! :)
Wonderful video sir
Very clear, thanks a lot!
Really good vídeo :)
why is there a 400-500% price difference when we go from cell to pack level?
great explanation
Hi Erik, great videos!
Can you also explain how an I²t counter works? I understand it is like a bucket that fills up. How does it empty itself?
Very good explanation sir
very nice and informative
Very informative
u create grate vid .thank u very much
this was a well presented explanation and i greatly appreciate it. i do have a question. can the leads of the BMS be connected to the plus or minus on the batteries. the info i have it should be the plus side. however overkill BMS is using some plus and some minus connection. do u have some inside?
thanks for ur time
We are building our EV Motorcycle.. we need this. Educational.
Thank you for your video. Great explanation for how a bms works. I am wanting to learn how to test a battery pack that won't take a charge. Is it a bad battery or a bad bms? Can the bms be bypassed to see if the batteries in the pack will charge directly?
Very Helpful 👍
I'm very new to ebikes. If you have 10 seconds I have a quick question sir; if someone was running 2 hub motors and their combined max current from the controllers was 60 amps, and you used a battery with 50amp BMS (52v 20ah), what would happen? If you ran WOT you may trip the BMS of the battery and it come back on after a few seconds? Or something worse? Thank you!
SOC is taken for System on Chip.
Nice information
Thanks
I am an engineering student from India. i am looking for a proper BMS and also the most reliable battery that my team NIRMAAN HYPERLOOP can use in our boring machine and the hyperloop pod, if you could help us with your knowledge on thus, it would be great. thank you
Amazing video. Simple and incredibly intuitive.
Thanks for the video. Great stuff
Things wouldn't exist without electronics
please Matlab Simulink also added for BMS.
great vedio. TYVM.
Sir, great Explained. Please post some video regarding Battery Testing in lab with power Anzylr .. and with some software
what is this SOE ?
Safe operating envelope
Sir please explain about DCDC/ESC converter.
Howdy S-S, ...
any RECOMMENDATIONS for a 48 Volt BMS brand Name ?
I run a 36 PV panel system, in a 6S / 6P configuration 230 volt "DC" input
ALL-IN-ONE 120 / 240 volt "AC" GROWATT Inverter SPF 6000T DVM-MPV
I would like to BUILD my own Battery Bank ...
Thanks,
COOP
the WiSeNhEiMeR from Richmond, INDIANA
...
Thank you 💐
Thanks a lot
Then where is thermal management
Usually master disconnect possible at negative side
Thank you
Thank you
Hello sir please make playlist 👍
i wanna work in your company please
you mean to say monitoring the cell or battery if its charging the wire for cell b1 b2 b3 just monitoring only not charging the charging come from negative and positive and the other 3 wire b1b2 b3 just monitoring the voltage when charging
Harikasın sayende rc arabamdaki sorunu çözdüm
Thanks
Fair enough 👍👍👍👍👍
thanks!
Tom Cruise little brother?? haha, good video.
One video is equivalent to 6 months of university courses :)
thanks 😅
Justin Trudeau teaching BMS, nice.
Nice
this isn't beatmania...
useful