Grazie! I don't know about you, but I still very much appreciate this video as I was able to follow along, even though he speaks a different language than my own. How many videos have you watched, where a presenter speaks your language, and with non-stop blabber before even a showing of anything worth attention is revealed? This guys is awesome though. Thanks for sharing the post.
I have a pair of LED H1s in high beams while I got a kit of anti-glare HID conversion in dipped beam and they are so much better, brighter and white and certainly lights up the road more further and even spot the hazard like a deer! However I had to put a load resistors in as it throws a fault up with blue beam symbol stays on on the dashboard due to no resistance.
H1’s have dust caps unlike H11’s. Usually these dust caps are small so the LED’s will have to be small as well. Secondly, if there’s a driver, you’ll need to cut the dust caps to fit all the wiring through and if space permits, you may squeeze the driver behind the dust caps as well. Then comes the heat sink from the LED’s which require cool air to operate to prevent the LED’s from burning out and imagine being stuffed inside a small dust cap along with the wiring and driver. Some drivers permanently remove the dust cap to solve these problems but in the long run, moisture and dust is going to get into your headlights (just look at your engine bay to see how much debris is inside) and ruin everything. It’s almost impossible to fit H1 LED’s into projector housing unless you take some time to modify the dust cap according to your respective LED.
this video is very informative especially changing the connecting pin. But i am curious the heat from the LED are all cover and tarp in that lamp area. Does it have any effect on the lamp ?
Thank you so much. I've searched for an instructional video in on H1 led installation in English, came across yours and wow. Great clear filming and so easy to follow.I take my hat off to you Sir.
@@carsandfurious_ hello,I have a Honda odyssey mini van, 2002, it didn't come with the foglights, so I ordered a set that will fit, my question is, the h1 bulbs are required, I want to do the high beam and low beam, will I need a special relay, or just go directly with the included wiring diagram ?
@@carsandfurious_ ok,thank you for the reply.. so basically I will just need a switch to turn them from high beam to low beam on the foglights ? These are h1 bulbs with the high/low beams,I'm wanting to use on the foglights...
non cè paragone tra led e alogene,ma si può vedere un video sul faro destro? perche io ho provato a cambiare una lampadina sul destro e dovrei smontare tutto il fanale.
Thank you my friend. Bought bulbs for 2006 hyundai sonata "plug and play" that werent so plug and play. You are literally the only video i could find that helped me threw this (male) 2 probgs & 1 female slot issue. Appreciate to & apologize for only knowing english, saw you replied in english on anothers comment so i thought i should send my appreciation. 🫡
@carsandfurious_ Indeed, sadly shortly after completing my lights I went to get lunch for the family & as I turned the key for the trip home all I got was a "click" for the relay switch in the hood. 😑 starter went out...& stayed out lol even after every trick to get her going again....by your superior experience, do you believe the two are connected or could be a possibility on why my starter went out? -I only ask because tomorrow I'm bringing car to auto shop and if it's something the mechanic needs to know about in case I did something wrong and will cause more issues in the long run. I will of course do my research myself online to find out but thought I'd run it by you to see what you felt. If you have time and feel like it, I'd love to hear your thoughts, no worries if you don't feel the need to respond. 🫡
@@Sir_Richard_Crainum_lll Hello, now I read. very strange I have used the lights for many years I have not had any problems. I think the cause is something else, you need to check the status of the battery and the cables. Let me know what the mechanic says
@@carsandfurious_ ended up simply just being a dead starter. Put the new one in & she's all better now! I really appreciate the feedback, really means a lot. 🙏
Halogen bulbs work better than Leds on non projector housing. On most cars the high beams are not beneficial to run on Leds, they just spread the light without throwing away
Ciao, quello che io non capisco..... è che appena montati funzionavano benissimo ma dopo 2 giorni le lampadine si accendono come 2 fiammiferi o neanche e la centralina mi errore..... secondo te cosa posso aver fatto di sbagliato!?!?!?
idk how in the world you can fit your hand behind the left headlight to get to the high beam bulbs. the fuse box is getting in the way as i was trying to install these led lights but i failed 🤣
Senza tagliare il cavo della lampadina , non posso metterci il nastro isolante per tenere attaccato il filo nero alla massa ? Comunque c'è contatto, giusto?
@@DevisBubbaDelPupo ciao scusami hai ragione ti ho fatto perdere tempo, pensavo fosse il video H7 mentre è quello H1, scusami ancora. ti servono proprio questo tipo?
Because of stubborn folks like myself who purchased the lights with the understanding they're a "plug & play" item & nothing else is needed for them to work...welp, screw waiting another day or so to order & receive the now needed adapter, said plug & play...let's make em plug & play :]
Grazie! I don't know about you, but I still very much appreciate this video as I was able to follow along, even though he speaks a different language than my own. How many videos have you watched, where a presenter speaks your language, and with non-stop blabber before even a showing of anything worth attention is revealed? This guys is awesome though. Thanks for sharing the post.
Thanks a lot to you !!!! Very kind of you!!😊
I have a pair of LED H1s in high beams while I got a kit of anti-glare HID conversion in dipped beam and they are so much better, brighter and white and certainly lights up the road more further and even spot the hazard like a deer! However I had to put a load resistors in as it throws a fault up with blue beam symbol stays on on the dashboard due to no resistance.
Hello, yes, some cars have canbus and a resistor must be mounted to turn off the error in the instrument panel
H1’s have dust caps unlike H11’s. Usually these dust caps are small so the LED’s will have to be small as well. Secondly, if there’s a driver, you’ll need to cut the dust caps to fit all the wiring through and if space permits, you may squeeze the driver behind the dust caps as well. Then comes the heat sink from the LED’s which require cool air to operate to prevent the LED’s from burning out and imagine being stuffed inside a small dust cap along with the wiring and driver. Some drivers permanently remove the dust cap to solve these problems but in the long run, moisture and dust is going to get into your headlights (just look at your engine bay to see how much debris is inside) and ruin everything. It’s almost impossible to fit H1 LED’s into projector housing unless you take some time to modify the dust cap according to your respective LED.
Completely agree
Dude, EVERY headbulb has a dustcap, not only H1's.
So this goes for EVERY led conversion.
I know, i did about 300 conversions. Both led and xenon
this video is very informative especially changing the connecting pin. But i am curious the heat from the LED are all cover and tarp in that lamp area. Does it have any effect on the lamp ?
Hello, unfortunately I mounted them a long time ago and now I don't have this car. But I found myself very well. Thank you very much
Thank you so much. I've searched for an instructional video in on H1 led installation in English, came across yours and wow. Great clear filming and so easy to follow.I take my hat off to you Sir.
Hello, thank you very much, very very kind of you
@@carsandfurious_ hello,I have a Honda odyssey mini van, 2002, it didn't come with the foglights, so I ordered a set that will fit, my question is, the h1 bulbs are required, I want to do the high beam and low beam, will I need a special relay, or just go directly with the included wiring diagram ?
@@shonoff83 Hi, no you don't need a relay, it's fine with original system
@@carsandfurious_ ok,thank you for the reply.. so basically I will just need a switch to turn them from high beam to low beam on the foglights ? These are h1 bulbs with the high/low beams,I'm wanting to use on the foglights...
@@shonoff83 yes just a switch for independent fog lights, and then high or low beam. You are welcome
Is it safe to put the grounding wire this way?
Hi, yes no problem. the work was done a long time ago and is still perfect.
non cè paragone tra led e alogene,ma si può vedere un video sul faro destro? perche io ho provato a cambiare una lampadina sul destro e dovrei smontare tutto il fanale.
Ciao , è si tutta un altra cosa. mi spiace non ho più la C3, però si può cambiare normalmente anche li senza smontare il faro no no
Thank you my friend. Bought bulbs for 2006 hyundai sonata "plug and play" that werent so plug and play. You are literally the only video i could find that helped me threw this (male) 2 probgs & 1 female slot issue. Appreciate to & apologize for only knowing english, saw you replied in english on anothers comment so i thought i should send my appreciation. 🫡
Hi friend, thank you very much. I am very happy that my video was of help to you. You are welcome 🙂🙏
@carsandfurious_ Indeed, sadly shortly after completing my lights I went to get lunch for the family & as I turned the key for the trip home all I got was a "click" for the relay switch in the hood. 😑 starter went out...& stayed out lol even after every trick to get her going again....by your superior experience, do you believe the two are connected or could be a possibility on why my starter went out?
-I only ask because tomorrow I'm bringing car to auto shop and if it's something the mechanic needs to know about in case I did something wrong and will cause more issues in the long run. I will of course do my research myself online to find out but thought I'd run it by you to see what you felt. If you have time and feel like it, I'd love to hear your thoughts, no worries if you don't feel the need to respond. 🫡
@@Sir_Richard_Crainum_lll Hello, now I read. very strange I have used the lights for many years I have not had any problems. I think the cause is something else, you need to check the status of the battery and the cables. Let me know what the mechanic says
@@carsandfurious_ ended up simply just being a dead starter. Put the new one in & she's all better now! I really appreciate the feedback, really means a lot. 🙏
@@Sir_Richard_Crainum_lll Well, the important thing is that you solved the problem🙂
I installed this h1
This month it is a little bit difficult
Because have no space to my hand
A hug from Brasil
Hi you are right, unfortunately there is little space, if you have a bit of big hands it is a bit of a problem. Thanks and regards to you🙂
Hello, with what model of camera did you record, the image looks very good.
Hi, yes it's true. i used a simple phone, at that time a samsung s8 +
Halogen bulbs work better than Leds on non projector housing. On most cars the high beams are not beneficial to run on Leds, they just spread the light without throwing away
Yes, I agree, I would add that for low beam headlights it is better to mount the LEDs on lenticular headlights and not on normal parabolas
Hi, where did you find the metal adapter for the ground? 😊
Hello, I got it from an auto electrician they definitely have them
Ciao, quello che io non capisco..... è che appena montati funzionavano benissimo ma dopo 2 giorni le lampadine si accendono come 2 fiammiferi o neanche e la centralina mi errore..... secondo te cosa posso aver fatto di sbagliato!?!?!?
Quelle H7 vanno bene senza canbus ma le H1 con canbus danno questo errore
@@andersonsimoes7417 Ciao su che auto le stai montando? su c3 come questa nel video?
Molto strano, non vorrei che sono usciti difettosi.dimmi prima auto e anno
Is it better comparing to halogen ?
is it my phone translating the video title or this dude using English title and speaking different language
Eu tenho um C3 e comprei as mesmas lâmpadas rsrsrsr, ficou muito bom.
Ok perfect!!
Ilumina bem ou eh só estetica, tô querendo colocar no meu c3 tambem
@@viniciusscopel8612 essas em questão iluminam igual uma halógena, não tem muito ganho. Depois troquei por uma shocklight que iluminam bem melhor
Ive seen wire adapters so you wont have to Modify the wires.
Hi, no any changes to the cables.👍
idk how in the world you can fit your hand behind the left headlight to get to the high beam bulbs. the fuse box is getting in the way as i was trying to install these led lights but i failed 🤣
hello, try again calmly, surely you can mount them
Exelente video
Thank you very much
Senza tagliare il cavo della lampadina , non posso metterci il nastro isolante per tenere attaccato il filo nero alla massa ? Comunque c'è contatto, giusto?
Ciao, volendo si però deve essere ben saldo altrimenti ti si spegne
@@carsandfurious_ Grazie mille, proverò 😊
@@davidevallarin9961 Grazie a te!! fammi sapere come va poi👍👍
LED high beams don't have focus. They just goes everywhere. I have also installed LEDs in my high beams and i regret it. Low beams are acceptable.
Hi, yes, the high beams depend a lot on the shape of the dish, not all cars have good results
👏🏾👏🏾👏🏾
Ottimo video, grazie!
Grazie mille!!
@ruggero99 non riesco a risponderti. é un comune fastom femmina. si può trovare in qualsiasi ferramenta
Video utilissimo! Sai mica darmi il link delle lampade che hai preso?
Ciao, grazie molto gentile!! Si il link è in descrizione del video proprio sotto. se non lo trovi fammi sapere che te lo scrivo qui
@@carsandfurious_ Se mi fai questa cortesia... purtroppo non riesco a trovarlo, vedo solo il link del canale e delle pagine social.
@@DevisBubbaDelPupo ciao scusami hai ragione ti ho fatto perdere tempo, pensavo fosse il video H7 mentre è quello H1, scusami ancora. ti servono proprio questo tipo?
Le devi montare su C3?
@@carsandfurious_ tranquillo... se si può si! Vorrei montarle su di una Peugeot 307 prima serie come abbaglianti...
It’s good instruction but 🤦♀️ I don’t wanna do that. I better return & refund my Led H1 $120 AUD. Because warranty will be void.
Ciao ma sono luci di posizione?
Ciao, no queste H1 solo le luci abbaglianti quelle alte diciamo così
Why didn’t you just buy an LED adapter wire? If you did, you wouldn’t have to cut wires
Hello, yes it is true. But it is a simple faston that can be restored immediately
Why order and wait for something when you can just replacing a connector?
Because of stubborn folks like myself who purchased the lights with the understanding they're a "plug & play" item & nothing else is needed for them to work...welp, screw waiting another day or so to order & receive the now needed adapter, said plug & play...let's make em plug & play :]
Non ti dà errore?
Ciao no su questo modello non ha il controllo delle lampadine fulminate, puoi mettere qualsiasi tipo di lampadina
Algum Br que também fez essa adaptação?? KKKKKKKKKK
Era più semplice e sbrigativo che ti fornivano il 2 in 1 ,sempre meglio chiedere prima di acquistare
Lol these bulbs suck. Halogen is clearly brighter.
Lol, you must be blind.
@@garmentdeals3772 I'm agree, on the video hallogen is better, but maybe is not reality...