From Memory they just sit around the shaft and when putting the outer case on you can work them into place. sorry for not being 100% sure but this process was done quite a while ago
I once went to a repair shop and watch a guy do this process, but on a Harlo forklift (modified Ford 445c I think). They stood the whole axle housing upright, make sure you put wheel lug nuts back on to protect the studs. I'm in the middle of this right now, it makes putting every back in place pretty simple. Now I've gotta rig up blocks on a pallet jack like these guys did, thank you for the good idea, much easier than the floor jacks and chain hoist I used to get the thing off. Cheers!
Would you know the axle retaining nut size off hand? I have a Ford 3550 and everything looks similar. I believe it to be a 34 mm but your input would be greatly appreciated!!
Hello, I would like to know what is the real position of control valve, manifold & tubes in tractor transmission ford 655a.because they armed my transmission and the F and R lever are inverted. if I act for the front, it goes backwards. if I drive backwards it's going to the front
if your going to do a video on how to replace brakes you have to explain things not just fly through it at high speed ok when you know how not much good for the diy person.
Doing this today on my 4000. Thanks for the video, it's a big help!
not a problem thanks for your comment
Cat has very similar design in 416B Backhoe.
Did I misunderstand? It seems that this includes brakes ... plus. Outside seal replacement too?
Muy buen video, de hecho el mejor a diferencia de otros que solo hablan pero no enseñan nada.👍👍👍👍👍👍👍👍
Excelente video. saludos 👍👍👍👍👍👍
Ford is very gold
Do you remember how you kept the steel disc centered? The one with the larger, non splined hole?
From Memory they just sit around the shaft and when putting the outer case on you can work them into place. sorry for not being 100% sure but this process was done quite a while ago
I once went to a repair shop and watch a guy do this process, but on a Harlo forklift (modified Ford 445c I think). They stood the whole axle housing upright, make sure you put wheel lug nuts back on to protect the studs. I'm in the middle of this right now, it makes putting every back in place pretty simple. Now I've gotta rig up blocks on a pallet jack like these guys did, thank you for the good idea, much easier than the floor jacks and chain hoist I used to get the thing off. Cheers!
Hola. podrían subir un vídeo de cómo reparar el toma fuerza de un Ford 4130
Gracias
top mechanics! well done
Hola cómo saber de la válvula eléctrica que va debajo y aplica el 4x4
So are the ford 5000??
Good morning
Good hard croc
Would you know the axle retaining nut size off hand? I have a Ford 3550 and everything looks similar. I believe it to be a 34 mm but your input would be greatly appreciated!!
I am sorry this job was done quite a wile ago so i am not 100% sure. But if you need any other help just ask
33 mm and thanks for the reply
Bravo
Anyone no what oil goes into the back end of a ford 4000
Super farm would do perfectly, there is a new Holland number standard it has to be above, can’t remember right now
Did I miss them replace the outer axle seal? mine is leaking oil on to the rim
No you did not miss the new seal going in unfortunately that bit was missed from this video. You do have to remove the half axle to replace it
Hello, I would like to know what is the real position of control valve, manifold & tubes in tractor transmission ford 655a.because they armed my transmission and the F and R lever are inverted.
if I act for the front, it goes backwards. if I drive backwards it's going to the front
Hi this tractor has a manual transmission so unfortunately i am unsure on how to resolve your issue
Job me
"Fe Fi Fho Fhum".....
if your going to do a video on how to replace brakes you have to explain things not just fly through it at high speed ok when you know how not much good for the diy person.
No sirve de nada no muestran como sacar balero y sello egoistas
T shat