Thanks for running the most detailed BMW coding channel on the RUclips. This is by far the best source of BMW software related DYI l I've seen apart from Shawn Sheridan's well known solutions. Keep it going, Vladimir. I really like how granular your BMW lessons are. Thanks for your passion and dedication to BMW community.
Hello and thank you to Vladimir for posting this video. For anyone using the G12 chassis, below is how I managed to flash the Alpina B7 EGS onto my 2016 750i xdrive. I tried Alpina B7 vehicle code 7F13, which ended up not working since the B7 is based on the G11/12 Chassis so I used stock 7F23 vehicle code. However, Alpina B7 (2016) earliest production on G12 Chassis was 12/2015 according to realoem site. My car was manufactured at 0715. So I had to change only the Vehicle Manufacture date for 0316 that E-Sys would recognize for 7F23. Changed I-Target (ship.) to 0316 build, and calculated. I learned from forums that you can tell if SVT SOLL is correct for Alpina if after injecting FA with 920/9XA in Salapa, you will see changes in DME, EPS, and (VDP) as well as EGS. The SWFL for the B7 for the G12 chassis (2016) was swfl_00003bb7-166_090_003. After flashing I saw the D1 indicator successfully and test-drove the car with no problems. Cleared errors after in ISTA.
@BimDoc I have a BMW G11 740d xDrive. The Alpina D7 is not coming out. Is it possible to upload the software from the Alpina G30 D5? And will it look the same as colleague @thespecter396 ?
Thank you, Vladimir, for all your hard work! Thanks to this video I successfuly flashed my 8HP70 gearbox in 2012 F11 535xD today! Greetings from Latvia!
@@kari-mattiloukiainen6825My BMW F11 is the pre-LCI model, so I only had to change the Typeschlussel from XB11 to XB71. The Zeitkriterium stayed the same: 1211 (the car has been produced in December 2011)
Something to remember is that this is guide for twin turbo engines, and not single turbo. For single turbo engine there is Japan version Alpina that fits to x30d engines much better.
come across to your channel purely by accident and WOW!! Your wealth of knowledge is astounding mate. Спасибо огромное что делишься столь важной информацией. Еще раз, спасибо. Подписка однозначно 👌🏻
Hi Vladimir, great video and thanks for steering desire to work on BMWs. Could you do a video on how to install a used transmission, reset and code it to work with the new host.
Very good video 🤘🏻 however… The last two years I was using xhp sw ST3 on my F530d, I get used it on very nervous gearbox even on comfort mode. I always want to compare with Alpina sw (now I did, thanks to you). I will put xhp back, like I said. I get used to it ob nervous shiffting, downshiffting and upshiffting is more lazy in alpina. But yeah, it is for free, that is advantage.
Hi, first of all, a big compliment for the content you produce.I have a question: Will there be another video on how to flash the DME/ECU specifically? I tried to remove the US speed limit by changing the type code from 3T33 to 3T31. Then I flashed the DME, but the problem still persists. Maybe it’s also related to resetting the DME’s working hours... I don’t know... Thanks 😊
Reflash DDE is easy but as you already mentioned it will give you nothing because of engine operating hours counter. So easiest solution is to make a chiptuning and that’s it 😉
Hello vladimir , do you have any idea what vehicle type to input for g12 alpina transmision , cannot find it on internet. By the way im subscribed to your channel, keep doing it you are very good !!!
Part two was never released. I did not find good method to measure the difference between ALPINA and standard SW in tranny. So it will be more scientific not feeling based. If you have any suggestion I’m one big ear 👂
@@BimDoc I guess a few measured pulls on Dragy or similar. But the main question is, is it worth it? I am thinking of trying the xHP gearbox map, but it's a few hundred €€€.
Thanks for another great video! I did watch all videos about bmw and learned too much already! I'm in doubt of do that because I think it is too much to my 118i f20, you think that is better do alpina or 2tb? Currently using 205.. my car has stage 3 remap..
Vladimir, I have a 2011 BMW 535i Xdrive with the N55 engine and the vehicle is equipped with the M-Package. Is my vehicle compatible with the Alpina software? Thank you and again Keep up the AWESOME contributions to the world of Bimmer Fanatics.
Hi Vladimir, i have a 2022 X5 M50i and i was wondering after watching this very informative video about transmission tuning that if its possible to flash tune my cars transmission with alpina software. Thanks
Thanks Vladimir for all your videos. I learned and, more importantly, i understand a lot from them. I have a G31 530xd made in April 2017, right hand drive and I want to try the alpina gearbox software. being a xdrive, i guess the Typschlussel code is different than in your video. can you help me with this one or where to find it?
@@BimDoctried the same one, but after calculations, on EGS didn't find a SWFL with 47DA, just another file with red, so i stopped doing anything further.
Hi, Vladimir! Very interesting and educational video! But on my car (G07) Salapa doesn't accept from the very beginning 920 and 9XA, the frame turns red and the values are not saved. What am I doing wrong?
@@vavava2045 Hi! Could you, please, share your experience on coding G07? Any success on adding Alpina gearbox, suspension, stabilizator parameters in G07?
@@SM-es8lt Hello! Unfortunately there is no success. I can't find the Alpina factory code for my car. In my configuration (engine + automatic transmission) it simply is not there.
Hi. Have you done part 2, or what is your opinions for that alpina software? And can i ask, is that alpina software usually in full psz files, or do i need download those from somewhere else?
@bimmerdoc Do I need to remove all other package assignments (business, m-sports, comfort, etc. package) from my FA after adding the 920 + 9XA? Thank you in advance!
Waiting for Part 2.. also, wanted to check if this will have any effect on wear and tear of gearbox? For the better or for worse. If shifts are optimised technically the wear and tear should be lesser, so curious. 😊
I still haven’t found a method how to measure a performance efficiently. That’s why there is no part 2. Of someone knows how to do it correctly let me know please.
Is it normal also for the others here that with the alpina software the Car always goes to First gear when nearby stopping? It is a Little bit annoying that now the Car goes by Like 5kmh from second to First gear, its a harder gearchange that you feel in the vehicle. Btw its an F11 530d
Hello and greetings from Switzerland I love watching your videos and i learn a lot of you. Thank you for that :) So my question is, my father has an BMW X3 F25 35d I want to do Alpine EGS Flash i have typekey WY71 and TimeCriteria 0316 So for i-level shipment i have to match timecriteria like 16/03/xxx to have correct svt_soll right ?
Thanks for the vid. Do you have to up the vehicle software level to the recent version BEFORE flashing? Or can you leave your, day, F10 mfd. in February, 2010 on that old software level and flash that Alpina firmware with time code that's more recent than your car? Or do you roolback the software level of your car to the software level of Alpina firmware that you're about to flash?
Кодирование после прошивки выполнять по оригинальному FA или измененному Alpina? Не вызывает ли противоречий изменение кода типа с VIN, где эти символы также имеются ? Отсутствие необходимости кодирования в примере - случайность или результат предварительного изменения SVT-файлов?
Just do some reserch and found that actually GA6HP26Z is another name for ZF6HP28 on BMW gearbox..means it can do the Alpina flash..and i believe for Getrag tranny they use GM infront of the model of the gearbox..please correct if i'm wrong..cheers mate
Владимир,привет. Для F01 не получилось,не знает esys код XB71 для него, пробовал разные YE73,YF73,KA73,KC53,YA73,YB53 и т.д. Tal успешно рассчитывается для 760,750х,но это не альпина,видно в swfl. Где я промазал,интересно? Машина F01 3dx 2012 8HP70 YC41
Владимир, возможен ли теоретически подобный трюк с прошивкой блока двигателя? У меня X5 45e (394hp) Новый 50e имеет с завода 490hp с тем же бензиновым мотором B58, уверен что ему на заводе просто сделали увеличение наддува
Great How-to. However, I would like to remind everyone that this should only be done to tuned cars. The Alpina software changes shift points to very late in the rpm register. For example, my F11 530d stage 1 (320hp and 675nm) makes max power at 4000rpm and max torque between 2-3000rpm. With the Alpina flash the gear changes were 4750rpm and one gear was 4900rpm. This is outside peak power and torque curves of your tune map making your car slower since there is no power or torque in those shift points. You need at least the 535d stage 1 for the F10/11 for this to be of any use. For G-series I suspect you need a 540d stage 1 at least.
@@hochh6978 with ESYS you need to change your Typeschlussel line to YA73. This uses the 750i N63 Alpina parameters. You havent told me what year model your car is only that it has an early N63. Assuming you have a F10 550i you can use YA73 to flash alpina transmission software to your 5-series.
Спасибо за информацию очень интересно. Приходилось F 10 525 Д менять коробку на 8hp70 Похожим методом с Autel ULTRA S все получилось супер все работает машина на ходу .
Вау!!! Ты реально крут! Браво! Владимир, если можно, несколько вопросов: 1) Я так и не понял, можно попытаться прошить коробку на моей F30 N13 или можно даже не пытаться?) 2) Я так понимаю, что ЕСИС так же предлагал зашить и двигатель АЛЬПИНОЙ, почему ты не стал этого делать? 3) И как я предполагаю, что подобной хитростью можно поднять класс мощности по типу 320>328? Заранее благодарен!
Hi, will this work on a F11 M550d? There wasn't the equivalent Alpina version, hence I'm not sure it will have any benefit on the 3-turbo engine. BTW, great work Vladimir... no channel is as clear in explaining things as yours.
Hello, Can I code with enet cable? I have full 4.45.30 so there are alpina software in it, too? I'm driving F31 30d 2013 what do I have to Change? Can you please help me and answer my question? Thank you
Hi Vladimir I have a 2011 bmw 640d and wanted to get the alpina software just on the gearbox. Can you please help guide me to do this? Many thanks Khalil
Hey buddy, do you have a video showing how to update the software on the NBT2 Unit ? I’m on id5 with a K firmware. I want to upgrade it so that I can get fullscreen Apple CarPlay
Updating NBT Evo is the same, as any other ecu. Only difference is that it takes around 1,5-2 h and it’s easier to brick it. Additional power supply is MUST! See my video about bmw technical campaign to understand how to flash ecu
@@BimDoc hi BimmerDoc, which option needs to be selected in the PARAMETERS TAB, Overwrite existing InstalledECUList or Merge with existing InstalledECUList? I am noticing some people using "Overwrite" and others using "Merge". Which one is correct and are there any risks of using one over the other? Thank you!
Hi, could you support with some info about how to distinguish which alpina flash is better for my 6hp26/28z (diesel), I have an xhp but after 1.5 year of experiments I don`t like it using in daylily driving looks like shifting 1-2-3 slippering, and then everything ok, also if I push accelerator little bit more to go faster it just slippering and try to shift to lower gear! Crap! Now I am on stock nothing special but for daily it is better for sure, also it accelerates faster by just pressing accelerator, without any redundant shifts.
@@BimDoc yeah me either, I saw only for n47 n54 but not m57 in pair with 6hp. Nevertheless may you can give me some advice, why stock firmware batter works in daily driving then xhp any available flash? Diagnosti shows good health transmission status.
How about a 2018 540iX (B58, G30)? Can it flash to Alpina? Tried hard to figure out which transmission it uses but still no clue... Need some help here.😵💫
Здравствуйте Владимир, Подскажите пожалуйста, есть Е70 3.0 дизель, Рестайл с ZF8HP70, посмотрел по выпуску Альпин, с такой коробкой и Е серия была только 2-ух литровая дизельная Alpina D3 Bi-Turbo… Как вы думаете, подойдёт ли данная прошивка на Е70? просто 3 литра вместо 2ух и полный привод смущают 😹💪🏻
Спасибо за внимание. Владимир, а ты знаешь про xHP, насколько хорош тюнер или какой вариант лучше, относительно бюджетный? Хочу заняться тюнингом автомобилей, в двигателе и коробке. Спасибо.@@BimDoc
I’m so disappointed, my car does not have the proper transmission for alpina software 😞 have you ever tried replacing a transmission? For example, I have an N55 engine with 8HP45 transmission. Can I swap 8HP70 transmission and code it to work? I imagine that it fits, as the alpina B3 is the same chassis as F30, right?
i have a G31 530dx i try with JD11 and it came after calculate only SWFL_000058D5 and not the 47D7 ? ty for help bro after i try JN51 the original one there is so SWFL blue or red all stay gray
i got it you where right my i-step was 17-03 i set it on 17-07-505 like yours and it works ty very much nice videos nice help keep going brother stay healty@@BimDoc
@@BimDoc любая прошивка - двоичный файл. Конечно, сравнивать биты не самая лучшая идея, а что если открыть в текстовом редакторе? В сети много программ для сравнения двух тестовых файлов, независимо от логики содержания. Есть даже онлайн сравнители.
Здравствуйте Владимир, подскажите можно ли залить в bmw f10 550xi 8hp70 софт Alpina, и какой тип кузова ставить, из видео и комментариев все льют в дизеля вот и решил спросить можно ли на бензиновую акпп заранее благодарю
Владимир здравствуйте! Собираюсь обновить ПО в своей машине, есть практически все, Зарядник, icom, pszd, ista+, esys, пусть и не большой но багаж знаний. Однако все еще боюсь приступать к прошивке, поскольку не хватает одной маленькой, но очень важной детали. Подскажите пожалуйста как можно получить вашу наклейку на ноутбук? 😂
Thanks for running the most detailed BMW coding channel on the RUclips. This is by far the best source of BMW software related DYI l I've seen apart from Shawn Sheridan's well known solutions. Keep it going, Vladimir. I really like how granular your BMW lessons are. Thanks for your passion and dedication to BMW community.
Thnx)
Hello and thank you to Vladimir for posting this video.
For anyone using the G12 chassis, below is how I managed to flash the Alpina B7 EGS onto my 2016 750i xdrive.
I tried Alpina B7 vehicle code 7F13, which ended up not working since the B7 is based on the G11/12 Chassis so I used stock 7F23 vehicle code.
However, Alpina B7 (2016) earliest production on G12 Chassis was 12/2015 according to realoem site. My car was manufactured at 0715. So I had to change only the Vehicle Manufacture date for 0316 that E-Sys would recognize for 7F23. Changed I-Target (ship.) to 0316 build, and calculated.
I learned from forums that you can tell if SVT SOLL is correct for Alpina if after injecting FA with 920/9XA in Salapa, you will see changes in DME, EPS, and (VDP) as well as EGS.
The SWFL for the B7 for the G12 chassis (2016) was swfl_00003bb7-166_090_003. After flashing I saw the D1 indicator successfully and test-drove the car with no problems. Cleared errors after in ISTA.
That’s a great information! Thank you for your input into bmw coding community )
@BimDoc I have a BMW G11 740d xDrive. The Alpina D7 is not coming out. Is it possible to upload the software from the Alpina G30 D5? And will it look the same as colleague @thespecter396 ?
Thank you, Vladimir, for all your hard work! Thanks to this video I successfuly flashed my 8HP70 gearbox in 2012 F11 535xD today! Greetings from Latvia!
Nice work!
What Typschussel/zeitkriterium You used?
@@kari-mattiloukiainen6825My BMW F11 is the pre-LCI model, so I only had to change the Typeschlussel from XB11 to XB71. The Zeitkriterium stayed the same: 1211 (the car has been produced in December 2011)
Something to remember is that this is guide for twin turbo engines, and not single turbo.
For single turbo engine there is Japan version Alpina that fits to x30d engines much better.
It is correct remark. So that software suits better bmw like G30 540d. Due to twin turbo.
There are differences between Alpina Europa and Alpina Japan? can you please tell me the SALAPA Code for it.
Hi! Could you please add more details? What should we change to flash Japan software? Is it available in full psdzdata?
What is the type code and date for a F07 530D GT LCI please?
Красавчик, не вздумай останавливатся, инфа важна иполезна, джегельме! Джемс продолжения. Алга!
Продолжу 😉
Спасибо! Очень полезное видео!
come across to your channel purely by accident and WOW!! Your wealth of knowledge is astounding mate. Спасибо огромное что делишься столь важной информацией. Еще раз, спасибо. Подписка однозначно 👌🏻
You are welcome 🤗
Again a good Video from you. Love it.
Glad you enjoyed it
And here we are, another interesting video with unique information. Thank you for the great work!
You always welcome 🤗
your video is awesome, can i ask for VO coding instead of flash? Thanks
VO coding with ALPINA FA will give you nothing (
Hi Vladimir, great video and thanks for steering desire to work on BMWs. Could you do a video on how to install a used transmission, reset and code it to work with the new host.
Not doable with standard bmw software
Владимир привет.По твоим видео начинаю учить английский язык.Спасибо .
Это хорошая практика 😉
Very good video 🤘🏻 however…
The last two years I was using xhp sw ST3 on my F530d, I get used it on very nervous gearbox even on comfort mode. I always want to compare with Alpina sw (now I did, thanks to you).
I will put xhp back, like I said. I get used to it ob nervous shiffting, downshiffting and upshiffting is more lazy in alpina. But yeah, it is for free, that is advantage.
Jep))
Hi,
first of all, a big compliment for the content you produce.I have a question: Will there be another video on how to flash the DME/ECU specifically? I tried to remove the US speed limit by changing the type code from 3T33 to 3T31. Then I flashed the DME, but the problem still persists. Maybe it’s also related to resetting the DME’s working hours... I don’t know... Thanks 😊
Reflash DDE is easy but as you already mentioned it will give you nothing because of engine operating hours counter.
So easiest solution is to make a chiptuning and that’s it 😉
Thnks for the video! Please make some more about E-series, like E39.
JOB DONE! Greta video!!!
Владимир спасибо, видео просто бомба 💥
Пользуйтесь )
Is there a part 2 with the review?
Haven’t done part 2
Because no food method to compare regular and ALPINA software in the tranny
Hello vladimir , do you have any idea what vehicle type to input for g12 alpina transmision , cannot find it on internet.
By the way im subscribed to your channel, keep doing it you are very good !!!
Not all G12 do support ALPINA
Hello Vladimir, thank you for your Video and the given Information. Do you know what is my Target Type key for my BNW G11 750d ?.
Same as for 730d / 530d
Just checking: Was part two of this video ever released? I couldn't find it in English when searching your videos.
Part two was never released.
I did not find good method to measure the difference between ALPINA and standard SW in tranny. So it will be more scientific not feeling based.
If you have any suggestion I’m one big ear 👂
@@BimDoc I guess a few measured pulls on Dragy or similar. But the main question is, is it worth it? I am thinking of trying the xHP gearbox map, but it's a few hundred €€€.
Thanks for another great video! I did watch all videos about bmw and learned too much already! I'm in doubt of do that because I think it is too much to my 118i f20, you think that is better do alpina or 2tb? Currently using 205.. my car has stage 3 remap..
In your case 2TB will be better. Because your transmission is not made for ALPINA (
Vladimir, I have a 2011 BMW 535i Xdrive with the N55 engine and the vehicle is equipped with the M-Package. Is my vehicle compatible with the Alpina software? Thank you and again Keep up the AWESOME contributions to the world of Bimmer Fanatics.
Tranny is not compatible with ALPINA SW ((
Hi Vladimir, i have a 2022 X5 M50i and i was wondering after watching this very informative video about transmission tuning that if its possible to flash tune my cars transmission with alpina software. Thanks
It might be possible. Depends on the transmission type installed
@@BimDoc do you provide online remote software upgrades or coding services?
Nice tutorial, as usual. Btw how to get those bimmerdoc stickers to be sure as flashing goes good?
Those can be earned on bmw programming courses )
Thanks for all the good content, learning a lot. Will this work with a 2016 f15? Not sure what the vehicle code would be. 2016 f15 xdrive.
It will not work in that specific vehicle unfortunatelly
Great work. Can I do It on G20 340d? What is typeshlussel for g20 xdrive ?
Should be doable
можешь сделать пж подробный ролик как менять стиль приборной панели на Альпину, а то я только купил бмв и как нужно не знаю)
В принципе можно и сделать )
nice video 👍👍 can you show the nbt evo retrofit programming too with e-sys ?
I understand that but cannot find type
Code for a g12 no where
Thanks Vladimir for all your videos. I learned and, more importantly, i understand a lot from them.
I have a G31 530xd made in April 2017, right hand drive and I want to try the alpina gearbox software. being a xdrive, i guess the Typschlussel code is different than in your video. can you help me with this one or where to find it?
Try to use the same code
I guess it should work fine (at least I haven’t noticed any problems)
@@BimDoctried the same one, but after calculations, on EGS didn't find a SWFL with 47DA, just another file with red, so i stopped doing anything further.
got the same do you find the problem?@@ShadowSpirity
Again a good Video from you.🙏❤
I appreciate that
Can this be applied to an 2016/2017 F11 520d automatic?
No it cannot. Because you have not suitable transmission installed
Hi Vladimir. How is this procedure different from chip tuning? May be you could explain it in part 2 video? Thank you!
Why not to cover that in part two )
Alpina B7 AWESOME !!!
It sure is!
Great tutorial, thank you very much! Can someone tell me the Typschlüssel KP91 (F10 550ix) for Alpina? Thanks again
Класс. Пока ещё борюсь с программой что бы все запускалось и читалось без ошибок. Смотрю все видео на будущее.
А вторая часть ещё не вышла?
Еще не вышла )
Hi, Vladimir! Very interesting and educational video! But on my car (G07) Salapa doesn't accept from the very beginning 920 and 9XA, the frame turns red and the values are not saved. What am I doing wrong?
It means that there were no ALPINA in G07 chassis
918
@@vavava2045 Hi! Could you, please, share your experience on coding G07? Any success on adding Alpina gearbox, suspension, stabilizator parameters in G07?
@@SM-es8lt Hello! Unfortunately there is no success. I can't find the Alpina factory code for my car. In my configuration (engine + automatic transmission) it simply is not there.
Hi. Have you done part 2, or what is your opinions for that alpina software? And can i ask, is that alpina software usually in full psz files, or do i need download those from somewhere else?
I really do like how tranny works with ALPINA SW
And yes it’s being found in full pszdzdata
@@BimDoc Thank you 🙏
@@BimDoc How about engine software... Can you put Alpina engine software for DME?
@bimmerdoc
Do I need to remove all other package assignments (business, m-sports, comfort, etc. package) from my FA after adding the 920 + 9XA?
Thank you in advance!
No need to remove those.
Waiting for Part 2.. also, wanted to check if this will have any effect on wear and tear of gearbox? For the better or for worse. If shifts are optimised technically the wear and tear should be lesser, so curious. 😊
I still haven’t found a method how to measure a performance efficiently. That’s why there is no part 2.
Of someone knows how to do it correctly let me know please.
Is it normal also for the others here that with the alpina software the Car always goes to First gear when nearby stopping? It is a Little bit annoying that now the Car goes by Like 5kmh from second to First gear, its a harder gearchange that you feel in the vehicle.
Btw its an F11 530d
посмотрел первую часть "Полный мануал/гайд по кодированию BMW F-серии через e-sys" не увидел там объяснения, что означают галочки в настройках
Там и не говорилось об этом. Ещё не знал тогда таких нюансов. В новом видео Esys для чайников уже более актуальная информация.
Hello, you can also tell in detail about the programming of the bmw e65 Autogetribe and the dinamic driv from Alpina?
Haven’t tested those. Cannot comment unfortunately
Hello and greetings from Switzerland
I love watching your videos and i learn a lot of you. Thank you for that :)
So my question is, my father has an BMW X3 F25 35d
I want to do Alpine EGS Flash i have typekey WY71 and TimeCriteria 0316
So for i-level shipment i have to match timecriteria like 16/03/xxx to have correct svt_soll right ?
Yes shipment must match the criteria
@@BimDoc alright thank you very much i ll try that :)
Thanks for the vid. Do you have to up the vehicle software level to the recent version BEFORE flashing? Or can you leave your, day, F10 mfd. in February, 2010 on that old software level and flash that Alpina firmware with time code that's more recent than your car? Or do you roolback the software level of your car to the software level of Alpina firmware that you're about to flash?
It’s better to update and keep the whole vehicle on one istep level for better performance!
Awesome. Can you please do a guide for 530d versions?
I have shown in that video for 530d (G30)
If you have F10, then it’s also doable
@@BimDoc Sorry, I meant F10. That's awesome and thank you for the guide!
I can help you with that, let me know if you’re still interested
Will this guide work on 2013 f10 535d?
Yes it will work
Worked with a F32 430D Coupe 3R51, had to create the files with esys 3.30 and flash it with 3.27 to to the car 🎉
Great feedback!
does it fit bmw m760li v12 2020
Thanks bro, but I didn't get it, can we do transmission coding like xHP freely with ESYS?
With esys you cannot make Chiptuning as with xHP
@@BimDocThanks sir, with esys can I code 2tb transmission and activate launch control to my g30 520i?
What is the production number for 2011 550? Xa71 is for 535d
Кодирование после прошивки выполнять по оригинальному FA или измененному Alpina? Не вызывает ли противоречий изменение кода типа с VIN, где эти символы также имеются ? Отсутствие необходимости кодирования в примере - случайность или результат предварительного изменения SVT-файлов?
Акпп кодируется изменённым ФА
Нужно или можно после прошивки прописывать оригинальный FA назад?
Hi mate, does this alpina flash software remove the torque limiters like xhp ?
Good question btw))
I don’t have a clear answer for that. Maybe someone knows it?
Hi Vladimir could you please post the link to the Car technology Forum. Thank you
Here you are
cartechnology.co.uk/
@@BimDoc Thank you
Good job great video..I have a question can this alpina flash put into GA tranny not ZF only?
Only ZF trannies are supported
@@BimDoc ok thanks for the info mate..gd luck and all the best for future content..
Just do some reserch and found that actually GA6HP26Z is another name for ZF6HP28 on BMW gearbox..means it can do the Alpina flash..and i believe for Getrag tranny they use GM infront of the model of the gearbox..please correct if i'm wrong..cheers mate
Спасибо за видео, все очень подробно рассказано. У меня f13 650, можно ли установить прошивку от f10 550? мотор и трансмиссия идентичны ведь.
Скорее да чем нет.
Надо пробовать
Владимир,привет. Для F01 не получилось,не знает esys код XB71 для него, пробовал разные YE73,YF73,KA73,KC53,YA73,YB53 и т.д. Tal успешно рассчитывается для 760,750х,но это не альпина,видно в swfl. Где я промазал,интересно? Машина F01 3dx 2012 8HP70 YC41
Когда-то делал на F01
Но да, там надо поиграть
Hello. What is the production number for 2010 550i without xd, left, europe
You can see your production number in your FA
What is the production number to flash your tranny to ALPINA is another question
@@BimDoc, yes, you are right, I mean flash to Alpina
Владимир, возможен ли теоретически подобный трюк с прошивкой блока двигателя? У меня X5 45e (394hp) Новый 50e имеет с завода 490hp с тем же бензиновым мотором B58, уверен что ему на заводе просто сделали увеличение наддува
Да, но нет )
Класс модности не поменять без сброса моточасов. Упретесь как минимум в это.
Great How-to. However, I would like to remind everyone that this should only be done to tuned cars. The Alpina software changes shift points to very late in the rpm register. For example, my F11 530d stage 1 (320hp and 675nm) makes max power at 4000rpm and max torque between 2-3000rpm. With the Alpina flash the gear changes were 4750rpm and one gear was 4900rpm. This is outside peak power and torque curves of your tune map making your car slower since there is no power or torque in those shift points. You need at least the 535d stage 1 for the F10/11 for this to be of any use. For G-series I suspect you need a 540d stage 1 at least.
I’m making the test with stage 1 on my 530d
Hey, nice comment, thanks for that. Figured, you are not going to flash that firmware on the initial revision of N63 since it's not tunable, do you?
@@hochh6978 you can definitely flash the B5 version of the software for the N63 equipped cars that are running stage 1.
@@ir655 hi, Arman. Do you know of any tune firmware for the first revision of N63? Me, I don't.
@@hochh6978 with ESYS you need to change your Typeschlussel line to YA73. This uses the 750i N63 Alpina parameters. You havent told me what year model your car is only that it has an early N63. Assuming you have a F10 550i you can use YA73 to flash alpina transmission software to your 5-series.
Спасибо за информацию очень интересно. Приходилось F 10 525 Д менять коробку на 8hp70
Похожим методом с Autel ULTRA S все получилось супер все работает машина на ходу .
Hi, will this work on 2017 440i f32 b58, if so what is the code I need to use please? Will I keep existing vehicle production date?
ALPINA software might be an option on that car.
If interested in programming send pm message for more details
Вау!!! Ты реально крут! Браво!
Владимир, если можно, несколько вопросов:
1) Я так и не понял, можно попытаться прошить коробку на моей F30 N13 или можно даже не пытаться?)
2) Я так понимаю, что ЕСИС так же предлагал зашить и двигатель АЛЬПИНОЙ, почему ты не стал этого делать?
3) И как я предполагаю, что подобной хитростью можно поднять класс мощности по типу 320>328?
Заранее благодарен!
С N13 ставится АКПП которая ну никак альпину не потянет (
Не прошивал ДДЕ под альпину так как там были и другие компоненты поменяны кроме софта.
@@BimDoc Теперь понятно!
Ну а если все же попробовать мне себе АКПП Альпиной зашить, чем чревато?
Hi, will this work on a F11 M550d? There wasn't the equivalent Alpina version, hence I'm not sure it will have any benefit on the 3-turbo engine. BTW, great work Vladimir... no channel is as clear in explaining things as yours.
It depends what transmission do to have.
If it’s ZF8HP70 then it’s doable
@@BimDoc thanks, will have a look (since it's got 740Nm, it must be one of the higher versions)
Можно ли аналогичным образом прошить подвеску? Поддерживает ли альпину BMW G20 320xd с адаптивными амортами?
Не сравнивал подвески на альпина.
Но не встречал информации про это.
По идеи надо просто посмотреть что Esys расчитывает и будет видно
Should we return original previous FA in case of further codings?
Modified ALPINA FA should not be saved into the vehicle
What's your experience with the Alpina transmission flash? I'm planning to flash my 530e mapped to 370hp.
Great video, thanks for your knowledge 👍🏼
tried that to my F30 330e and failed at flashing bootloader, seems like the hardware difference for hybrid transmission. Let me know if u succeeded
Hello does anyone know if this will work on X5 F15 50i 2015? And do you know the typeschussel?
Unfortunatelly on F15 ALPINA is possible only until 2013
@@BimDoc Thank you! Sad to hear
топ контент. лешил многих заработка :) молодец.
Эта инфа далеко не новая. Не думаю что на этом кто-то состояние делает.
@@BimDoc просто я давно искал это, но на ютубе такого нет. А в английских форумах никто на пальцах не обьясняет, все полуфразами, да обрывками.
Hello,
Can I code with enet cable?
I have full 4.45.30 so there are alpina software in it, too?
I'm driving F31 30d 2013 what do I have to Change?
Can you please help me and answer my question?
Thank you
Your esys is good for that.
You can flash ALPINA tranny software wo problems
@@BimDoc I mean ista is a BMW software and there is alpina code too or do I have to Change some files?
Dose the alpina gearbox software update work on 2006 650ci thanks
There are some versions for E series as well
But I haven’t tested those
Hello....very nice job and a good tutorial....For the Bmw 520d F10 with 8hp45 can be code alpina software?Thanks and keep on the good job.. 👌👌👌
ALPINA will not work well on 8HP45 or 8HP50 gearboxes
@@BimDoc thanks for the answer! 👌👌
@@BimDoc А где можно увидеть модификацию своей коробки?
Hello, how are the gearbox adaptation values (clutch fill pressure and rapid fill times) after putting alpina software? Have increased?
Actually I haven’t checked those. But it’s worth checking ))
Hi Vladimir I have a 2011 bmw 640d and wanted to get the alpina software just on the gearbox. Can you please help guide me to do this? Many thanks Khalil
This video is a guide how to do it 😉
Would this work for a 2019 m550i?
You should have a right transmission over there. So might work
Thank you!
Is it possible to do this in f07 530d with the factory level 09-08-532, or car is to old?
You have compatible tranny. So it is possible!
Love your videos and easy explenations!
PS: It's AlpinA, pronounce the A, else you're talking about a French brand Alpine ;)
Roger )
Hey buddy, do you have a video showing how to update the software on the NBT2 Unit ? I’m on id5 with a K firmware. I want to upgrade it so that I can get fullscreen Apple CarPlay
Updating NBT Evo is the same, as any other ecu. Only difference is that it takes around 1,5-2 h and it’s easier to brick it.
Additional power supply is MUST!
See my video about bmw technical campaign to understand how to flash ecu
@@BimDoc hi BimmerDoc, which option needs to be selected in the PARAMETERS TAB, Overwrite existing InstalledECUList or Merge with existing InstalledECUList? I am noticing some people using "Overwrite" and others using "Merge". Which one is correct and are there any risks of using one over the other? Thank you!
Hi is it possible to work with psdz data 4.47.31 with bmw f11 from 07/14?
Yes
Thanks for your help, butI cant calculate svt Target, istep is greyed out. I use esys 3.30.1 what can be the Problem? I got full psdz data
Man.. i forgot to activate fa.. Now it worked fine for me! Really glad that we got you here on RUclips!!!🎉
can i flash with esys pro launcher 2.8.1 ?
Don’t use any launcher to flash
Use plain esys 😉
Hi, could you support with some info about how to distinguish which alpina flash is better for my 6hp26/28z (diesel), I have an xhp but after 1.5 year of experiments I don`t like it using in daylily driving looks like shifting 1-2-3 slippering, and then everything ok, also if I push accelerator little bit more to go faster it just slippering and try to shift to lower gear! Crap! Now I am on stock nothing special but for daily it is better for sure, also it accelerates faster by just pressing accelerator, without any redundant shifts.
I doubt there is an ALPINA software for 6HP26
@@BimDoc yeah me either, I saw only for n47 n54 but not m57 in pair with 6hp. Nevertheless may you can give me some advice, why stock firmware batter works in daily driving then xhp any available flash? Diagnosti shows good health transmission status.
How about a 2018 540iX (B58, G30)? Can it flash to Alpina? Tried hard to figure out which transmission it uses but still no clue... Need some help here.😵💫
50i will definitely have right tranny
40i tranny if I remember correctly cannot handle so much torque, so not ALPINA compatible
Habe ein M550i welchen Typenschlüssel muss ich für ihn nehmen ? JD51 ist richtig ?
@@BimDoc Thank you sir. This kind of info is HARD to find online!
Приветствую, альпина шла только на бензиновых двигателях ? Можно ли ее поставить на дизель ? Е60 530d
На дизелек тоже залитает.
@@BimDocа по оборотам разве разницы нет ?
Здравствуйте Владимир,
Подскажите пожалуйста, есть Е70 3.0 дизель, Рестайл с ZF8HP70, посмотрел по выпуску Альпин, с такой коробкой и Е серия была только 2-ух литровая дизельная Alpina D3 Bi-Turbo… Как вы думаете, подойдёт ли данная прошивка на Е70? просто 3 литра вместо 2ух и полный привод смущают 😹💪🏻
Хороший вопрос. Лучше сделать просто тюн акпп. Наверняка будет 😉
@@BimDoc делаете? Как с вами связаться?
Здравствуйте Владимир
Там коробки стоят не подходящие. На них не будет прошивки от ALPINA
Спасибо за внимание.
Владимир, а ты знаешь про xHP, насколько хорош тюнер или какой вариант лучше, относительно бюджетный?
Хочу заняться тюнингом автомобилей, в двигателе и коробке.
Спасибо.@@BimDoc
xHP неплохо но чисто для себя. Очень много берут за каждое чтение.
@@BimDoc Если мы покупаем 1 ручную, мы не можем использовать ее на нескольких машинах с одним и тем же двигателем. я правильно понял?
I’m so disappointed, my car does not have the proper transmission for alpina software 😞 have you ever tried replacing a transmission? For example, I have an N55 engine with 8HP45 transmission. Can I swap 8HP70 transmission and code it to work? I imagine that it fits, as the alpina B3 is the same chassis as F30, right?
Transmission swap will case more problems that solutions.
It’s easier to chip tune transmission
Yes of course. I was just asking to know if it would be possible in theory, but not actually do it. Love your vids, keep it up!
Is this good for f34 2014?
If you have right gearbox, then yes
Hi I can't find any information for the g15 m850i is this possible, also could you do engine ecu too?
It should be doable. Flashing engine ecu with alpine software is not a good idea (
hi can you help me to flash my bmw f11 535d alpine software gearbox i have enet cabel ?
Yes it’s doable
Contact me directly pls
@@BimDoc thanks do you have email, or whatsapp i can contact you thanks
Under every video in then description
Hi,where can i get a bimmerdoc sticker, i heard if you put it on a car it will give you plus 50 horsepower
52 to be precise 😅
i have a G31 530dx i try with JD11 and it came after calculate only SWFL_000058D5 and not the 47D7 ? ty for help bro
after i try JN51 the original one there is so SWFL blue or red all stay gray
Don’t forget to play with istep shipment as well
ok but you dint change something in your video? my i step shipment is the same as yours (2017-06 produce date)@@BimDoc
i got it you where right my i-step was 17-03 i set it on 17-07-505 like yours and it works ty very much nice videos nice help keep going brother stay healty@@BimDoc
Доброго дня! Когда ожидать вторую часть? :)
С этим туго. Не нашел адекватного способа для наглядного сравнения прошивок в реальной жизни.
Если есть идеи, то всегда пожалуйста )
@@BimDoc любая прошивка - двоичный файл. Конечно, сравнивать биты не самая лучшая идея, а что если открыть в текстовом редакторе? В сети много программ для сравнения двух тестовых файлов, независимо от логики содержания. Есть даже онлайн сравнители.
Здравствуйте Владимир, подскажите можно ли залить в bmw f10 550xi 8hp70 софт Alpina, и какой тип кузова ставить, из видео и комментариев все льют в дизеля вот и решил спросить можно ли на бензиновую акпп
заранее благодарю
Да на данный авто можно залить ALPINA
Were you able to flash it?
Владимир здравствуйте! Собираюсь обновить ПО в своей машине, есть практически все, Зарядник, icom, pszd, ista+, esys, пусть и не большой но багаж знаний.
Однако все еще боюсь приступать к прошивке, поскольку не хватает одной маленькой, но очень важной детали.
Подскажите пожалуйста как можно получить вашу наклейку на ноутбук? 😂
Наклейка это очень важный элемент для программирования ))))
Выдается участникам курсов по бмв от BimmerDoc )))
Так а где ссылка на форум ?
S962A опция вопрос?!
Приветствую Что означает эта опция специальное поле для характеристик двигателя BMW E39 в прошивке Объясни пожалуйста
К сожалению не знаю. Если кто знает, пишите в комментах. Интересно 🧐
is it possible on 520d also ?
Negative. Tranny does it support that
Владимир, здравствуйте, могу ли я прошить акпп 8hp75, bmw F10 m550d 2014 года прошивкой от Alpina? Спасибо!
50d должен проливаться под ALPINA
@@BimDoc спасибо 🙏
fatalix ?