Thankyou for good comment, loads of videos are planned as loads of work is waiting to be done on 407s also once lockdowns and things goes away loads of car events videos will be filmed
Maybe need to update diagbox. If its grey its either not there or diagbox needs a update depends on a car and year also sometimes it ask you to choose wich ecu you have so just needs to try all and if it lets you access then thats the one. And if it doesnt let you access it then not. Grey means the diagbox cant access them or they are not there
Hello, good video, I have a 206 hdi 03. I have the same software as you but i have been using pp2000 for mine. Can i use diagbox the same as you are using? The software looks better. Thanks
Hi mate i think you already using best software for it. I normally use Peugeot planet for cars older then 2004 and for cars from 2004 onwards I use Diagbox. But you surely could use Diagbox for your 206 aswell with no problems
Diagbox you can get from ebay for like 50£ it's basicly 2 discs and cables. It's best to have a separate laptop just for Diagbox also it works best on Windows xp professional.
@@Mad4FrenchCars ok thanks very much i do in fact have the same set up as you i got mine from ebay same as you. I have some faults i need to fix like faulty mass air flow valve air intake and abs fault to sort out, should keep me busy!
@@Ptvermoes Mileage in any citroen or Peugeot is recorded in bsi and speedometer so if you get bsi and speedometer from a same car with same part numbers then that's one way to do it, mind you then ignition lock and door lock will have to be changed or a your keys programmed to new bsi. With Diagbox you can't change mileage only change it from km to miles I believe
Hi mate i cant remember now on top of my head. What happen did you pull out a steering wheel angle sensor out of comms unit? Why is it giving you this fault? I have pulled a steering wheel angle sensor out once with a steering wheel from comms unit i had to get a new comms unit as it was no chance to put it back together same like factory
Just go through liturally every section most likely will be under some actuator test. I remember having a same issue vut i couldnt manage to recalibrate it and it worked fine with another used comms unit and sensor.
@@Mad4FrenchCars Hi Mate! I have problem with ESP (unfortunately it's sensor in whell). I tried calibration in PP2000 but without effect. I heard that in DiagBox it's possible - but I can't find it :-) Stering column have 660* possition and no react on change possition of whell.
@@mkonikowy i am not a 100% sure what the solution would be but you might have more luck if you join a facebook hroup called Peugeot 407 UK there is over 2000 407 owners and someone deffinatelly had it sorted same issue very recently.
I watch you from Greece I have the same car and here I do not deal with these cars. I like learning things about the car.
Nice one mate. I really apreaciate you find a video use full. Thankyou for watching a videos
Very good walkthrough of the diagnosis, thanks a lot
Thanks for all these useful infos! Waiting for more videos abt the 407
Thankyou for good comment, loads of videos are planned as loads of work is waiting to be done on 407s also once lockdowns and things goes away loads of car events videos will be filmed
Thanks for sharing this important information 👍🏿
Thank you for watching
Thanks for your video. Very helpful.
Thanks for the video , can you please tell me where I can download diagbox software ?
Thanks, great video!
Thankyou mate I will make a better video with Diagbox soon as I have it on fast laptop now
Great, thank you 👍
I will deffinatelly gonna make more videos with diagbox in a future this one was just a quick one. Thankyou for a good comment
Hey man is this chinese version of diagbox? Where did you get it
Thanks m8 going get 1
Best investment
Some of them are gray and green is that problem. When I try to do it it's saying ecu not recognized? Can you help me with that?
Maybe need to update diagbox. If its grey its either not there or diagbox needs a update depends on a car and year also sometimes it ask you to choose wich ecu you have so just needs to try all and if it lets you access then thats the one. And if it doesnt let you access it then not. Grey means the diagbox cant access them or they are not there
Diagbox fine on a W8.1 laptop I had lying around with no VM... Yet to test on W10.
If on windows 10 then only properly works first update i think 7.57 after that you have to use virtual drive
Hey, how do you code a second hand abs pump with lexia/diagbox on Peugeot 3008?
Hi mate I am not sure about coding but prity sure you have to carry out bleeding of a brake fluid procedure
Hi do you have the ebay link? How much does the cable cost? They are quite expensive :(
Türkçe çevirisi yaparsan çok dağa güzel anlarız tesekkurlrr
Which DiagBox Version are you using ? and which HW version are you using ? I'm trying to get one :)
Its quite an old version but it works on Windows 10 with no virtual drive 07.57
Hi, can DiagBox reset Adblue warning on Peugeot 508?
Yes it can also it can tell you why warning is there in a first place.
@@Mad4FrenchCars Okay, thank you very much...
Hello, good video, I have a 206 hdi 03. I have the same software as you but i have been using pp2000 for mine. Can i use diagbox the same as you are using? The software looks better. Thanks
Hi mate i think you already using best software for it. I normally use Peugeot planet for cars older then 2004 and for cars from 2004 onwards I use Diagbox. But you surely could use Diagbox for your 206 aswell with no problems
Diagbox you can get from ebay for like 50£ it's basicly 2 discs and cables. It's best to have a separate laptop just for Diagbox also it works best on Windows xp professional.
@@Mad4FrenchCars ok thanks very much i do in fact have the same set up as you i got mine from ebay same as you. I have some faults i need to fix like faulty mass air flow valve air intake and abs fault to sort out, should keep me busy!
@@Mad4FrenchCars Can you change the millage? I bought a used display for my Citroen C4 Picasso, and now the millage is wrong. Need to change it.
@@Ptvermoes Mileage in any citroen or Peugeot is recorded in bsi and speedometer so if you get bsi and speedometer from a same car with same part numbers then that's one way to do it, mind you then ignition lock and door lock will have to be changed or a your keys programmed to new bsi. With Diagbox you can't change mileage only change it from km to miles I believe
Does it work win7 and 10?
I believe if you use virtual drive then you can run on any windows. I run ot a first update on windows 10 with no virtual drive and it all works
My diagbox not see the ecu.what cant be the cause?sorry for my english
I am not sure mate sometimes it happens then ignision is not on before scanning a car. I am not sure what could couse it
@@Mad4FrenchCars i try what you sad tomorow.thank.s bro😊
I try it works.thanks you are the best
@@bmarian9357 thank you matr
I have a fault....fuel flow regulator....can i fix de regulator...i mean clean it????
Hello Dear ! Do You know where I can do: steering angle sensor calibration in Peugeot 407 in DIAGBOX ? I can't find it.. mhmm
Hi mate i cant remember now on top of my head. What happen did you pull out a steering wheel angle sensor out of comms unit? Why is it giving you this fault? I have pulled a steering wheel angle sensor out once with a steering wheel from comms unit i had to get a new comms unit as it was no chance to put it back together same like factory
Just go through liturally every section most likely will be under some actuator test. I remember having a same issue vut i couldnt manage to recalibrate it and it worked fine with another used comms unit and sensor.
@@Mad4FrenchCars Hi Mate! I have problem with ESP (unfortunately it's sensor in whell). I tried calibration in PP2000 but without effect. I heard that in DiagBox it's possible - but I can't find it :-) Stering column have 660* possition and no react on change possition of whell.
@@mkonikowy i am not a 100% sure what the solution would be but you might have more luck if you join a facebook hroup called Peugeot 407 UK there is over 2000 407 owners and someone deffinatelly had it sorted same issue very recently.
Go to....esp....repair....pack repair
У вас руль не з тої сторони стоїть, от в тому і проблема !
You probably right lol